Search Documents

By Joseph W. Leonard

Evidence is presented to show that certain coals can be super-cleaned, using present coal preparation processes, to reduce sulfur below levels that are commonly believed to be possible. The evidence points to the need to develop continuous sorting methods by which coal coming from a mine can be segregated so that different raw coal types can be processed separately to produce a super-clean coal in addition to coals cleaned to more common levels of sulfur. Evidence is presented and techniques discussed that may be applicable for making the method feasible.

Jan 1, 1976

By K. H. Nimerick, G. P. Laflin

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes polllution.

Jan 1, 1980

By Harold E. Thomas, Samuel S. M. Chan, Nicholas Bada

The U.S. Bureau of Mines has developed a technique for locating and evaluating bedding plane cracks in mine roof by an air-injection and hot-film flow logging technique. It is ultrasensitive to cracks and is especially useful for detecting the early stage of crack development. Potential applications include: (1) correlation with roof sag measurements, (2) locating cracks for grouting, (3) comparison of mechanical and resin roof bolt effectiveness, and (4) possible delineation of the fracture zone to confirm the arch hypothesis. The required equipment is inexpensive and simple to operate.

Jan 1, 1975

By J. Jr. Hudy

The objective of this investigation of the Cendrex was to determine the applicability of the X-ray instrument for the measurement of the ash content of coal. Developed by the Dutch State Mines, this instrument is designed to provide ash analysis of any desired coal product with only a 5-minute lag between sample collection and analytical result. The unit could, with limit controls, be used to feed back signals to preset the separating gravity of coal washers, control the ratio of various coals needed to produce an acceptable blend, and permit the sorting of a washed product into two qualities, one which is below and the other which is above a prescribed ash content. This unit can also be used discontinuously for rapid determination of samples of coals taken in the usual manner.

Jan 7, 1968

By A. Wahab Khair

This paper presents an analysis of fracture mechanisms in coal subjected to bi-axial state of stresses, indentation of laterally con- fined coal specimen. Coal specimens were loaded to failure by the straight wedge indenters at various lateral confinement pressures. Strain distribution and acoustic emission characteristics of coal specimens under stress were recorded. The influence lines of vertical forces acting on the horizontal straight boundary of the coal specimen for each type of wedge indenter have been established using holographic interferometry technique. The effects of wedge indenter angle, confinement pressure, and coal anisotropy on fracture types, failure modes, and post-failure conditions were studied. The results indicated that combined application of holographic interferometry and acoustic emission monitoring techniques is not only suitable for studying deformability of heterogeneous and microscopically discontinuous material under stress but it also enhances the mode of fracture during the post failure stage.

Jan 1, 1984

By A. E. Moss, J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing. By 1954 iron ore will begin to move towards American blast furnaces, and shortly thereafter the annual rate of production is expected to reach 10 . million tons. To bring this vast project into being over $200,000,000 will have been spent for exploration and development, mining equipment, hydro plants, townsites, the building and the equipping of . a 360-mile railroad, and the construction of docks and ore-handling facilities. The most important iron ore deposits are located over 300 miles from tide water, see frontispiece and also Fig. 1. The frontispiece shows principal sources of iron ores and manganiferous iron ores for the U. S. and Canadian steel industry, and the major smelting districts are shaded on the map. No navi- gable rivers lead into the interior. When work was . commenced on this project there were no roads, no railroads, no communication ,system, no inhabitants, and no adequate maps either topographical or geological. The geological field season was limited to approximately 100 days per season. The obstacles facing this enterprise were many and varied. Its success will be due to the integrated team work of people of diverse skills. Explorers, Indian guides, prospectors, geologists, surveyors, mechanical, civil, electrical, and mining engineers,

Jan 1, 1954

Jan 1, 1910

[ ]

Jan 1, 1942

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is undcrlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman Counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production

Jan 1, 1938

By Ossi V. I. Hintikka, Andrew Balint

Sorting tests on limestone at the Lohjan Kalkkitehdas Oy Ojamo mine, Finland, are described. The tests, conducted to evaluate a Sortex 811MW optical separator, were successful, and upon completion, the sorting machine was put into production. Optical separation characteristics of the limestone, used for cement manufacturing, are described. Problems of winter operation are discussed. Operating costs are given.

Jan 1, 1972

By Richard R. Zupp, David A. Stevenson

An experimental method to determine the carbon activity in various solid solutions was developed. Samples of the solid solutions and an Fe-C reference sample were equilibrated with respect to carbon content by annealing them in a Hz-CHI gas mixture in a closed cell. The carbon content of each sample was determined, and the carbon activity was obtained from the carbon content of' the reference sample and well-established data for the dependence of the carbon activity on the carbon content in Fe-C alloys. The influence of vanadium on the activity of carbon in austenitic Fe-C-V alloys at 1000°C was determined by this technique. A general semiempirical correlation was developed to describe the dependence of the activity coefficient of- carbon on the composition of ternary austenitic iron-base alloys containing interstitial carbon and a substitutional solute. The correlation is particularly useful in predicting the partitioning of- carbon between various alloys. THE influence of substitutional solutes on the activity of interstitial solutes in metallic solid solutions is important in the theory of alloy phases. Solid solutions of particular interest are the fcc austenite phases of ternary Fe-C-Z systems, in which carbon is the interstitial solute and Z represents any substitutional solute. Carbon-activity data are also needed in these solid solutions to solve practical problems; the quantitative treatment of diffusion-controlled transformations' is an examvle. Experimental information is available for ternary austenitic solid solutions containing Mn,2 Si,2 and A16 as the substitutional solute. Because qualitative preliminary studies indicated that vanadium appreciably decreases the carbon activity,14 the present investigation was undertaken to determine the influence of vanadium on the activity of carbon in austenite. Although Flender and ever" measured carbon activity over a range of compositions in the Fe-C-V system, they were primarily interested in determining phase boundaries in the ternary system, so most of their measurements were outside the composition range for stability of single-phase austenite. Petrova and Shvartsman' also made limited measurements of the carbon activity in Fe-C-V alloys. The dependence of the carbon activity on the carbon content of an alloy may be determined by passing COCOz or H2-CH4 gas mixtures of carefully measured composition over the alloys, determining their equilibrium carbon content, and utilizing the relevant equilibrium relationships. smith16 used this technique with both CO-COZ and HZ-CH4 gas mixtures to determine the dependence of carbon activity on carbon content in pure Fe-C alloys. His data, which are in good agreement with those of some previous and subsequent investigators,6'17 but not with those of others,lfl'ao are usually considered to be the most reliable. Although the same method can be applied to Fe-C-Z alloys, it is difficult experimentally, because the appropriate gas mixtures are almost pure CO or Hz. A simpler technique is to simultaneously equilibrate the Fe-C-Z alloys and pure Fe-C alloys with the gas mixtures, and then use Smith's data to determine the carbon activity in the pure Fe-C alloy. A number of investigators have employed this technique. others Have used the partitioning of carbon at the interface of a diffusion couple prepared from an Fe-C alloy and a Fe-C-Z alloy. In the present study, a closed-cell method was developed by which carbon was selectively transferred via a gas medium between pure Fe-C alloys and Fe-C-V alloys which were not in physical contact. A similar method was developed independently by Heckler and winchel14 and used to study the Fe-C-Ni system. EXPERIMENTAL METHOD A schematic diagram of the experimental arrangement is shown in Fig. 1. In a typical experiment, a 5-g Fe-C sample was placed in one compartment of a quartz cell, and a 5-g Fe-V sample was placed in each of the other compartments. The cell was evacuated, outgassed, backfilled with approximately 125 Torr of hydrogen, and sealed. After being placed in a fur-

Jan 1, 1967

By A. Eilers

ALTHOUGH the process to which I refer in this paper has been in successful operation for nearly five years, during which time it has been introduced, superseding all other processes having in view the same end, in almost every lead refinery in the country, no description of it, giving economical data, has ever appeared in print, nor has the process been known in its details to any considerable number of engineers beside those conducting it at their works. A discussion of this subject at the present time becomes especially interesting in view of a late publication in the Prussian ministerial organ for Mining and Metallurgy, by Dr. Wedding, in which the method of treating the zinc-silver-lead alloy by distillation, as finally settled upon at Tarnowitz, is very minutely and fully described. It is the more interesting, because in that article reference is made to the American method in an unfavorable light, while, at the same time, it is clear from the article itself, that the most important details of the process, besides the one that it is conducted in black-lead retorts, were not at all understood. In publishing herewith the details of our American method, one of my objects is to invite comparisons between our simple and direct process and the elaborate one at Tarnowitz. In extracting the silver from work-lead by means of zinc, it is always the intention, in this country, to obtain a zinc-crust so rich in silver that the rich lead resulting from subsequent distillation

Jan 1, 1875

By Arthur F. TQggQrt

THE approximate status of education in ore dressing in 1871 is reflected by Rossiter W. Raymond in an article written at that time presenting the curricula and descriptions of the laboratories at the various mining schools in the United States. For the most part, the curricula in which ore dressing was taught were for mining engineering. They comprised courses in geology, mining, and pyrometallurgy about equal in point or credit weights; a short course in ore dressing, and a somewhat longer course in assaying; and courses in surveying, hydraulics, power, and strength of materials-all superimposed on a broad foundation of physics, chemistry, and mathematics. Some curricula contained a fair content of the humanities. Then, as now, the emphasis on fundamentals was greater in the older colleges and universities. The report on the Columbia School of Mines, then relatively young, emphasized that a large percentage of its students were college graduates. As technical and scientific knowledge grew, first metallurgy and then geology were set up as separate curricula. So far as curriculum designation is con-

Jan 1, 1947

By Dorsey Hager

THE possibilities of finding new oil pools in Oklahoma and Kansas are far from promising. In 1916, the only new pools of importance were the Franchot pool near Bixby, the Garber, and the Billings pools in Oklahoma, and the Virgil and Utopia fields in Greenwood County, Kansas. In the first 8 months of 1917, a small pool of unknown extent was opened south of the Stone Bluff pool in Oklahoma, and a pool near Casey, Paunee County, Oklahoma. In Eastern Kansas, interest has been. caused by the sinking of new wells near the old Iola pool, but nothing of magnitude has yet been found. The outlook for new pools is far from encouraging, especially as geological surveys have covered all of Oklahoma and Kansas. There are a few areas where geological surveys throw little or no light on the subject, as exposures are poor, but the chances of finding new pools in such areas are slight indeed, if one can judge from the past history of such areas. So far the geologists have based their opinions largely upon the presence or the absence of geologic structure, such as anticlines, domes, and terraces, but some pools will most certainly be found where no surface structure exists, but where local changes in the sand body favor oil accumulations. However, the possibilities of new pools off structure are small, as fully 90 per cent. of the oil pools are on definite structure. In the past, it is estimated that one test in 150 "wild cats" or new tests has brought in a new field. The writer feels safe in asserting that the proportion will decrease still further, so that but one out of 500 new tests may bring in a pay well in a new area. From now on the principal field of work in Oklahoma and in Kansas will consist in developing the present pools. The years 1915, 1916 and 1917 saw the high peak of Oklahoma and Kansas oil production. The Eldorado and the Augusta oil fields present the largest possibilities for continued production in Kansas. These two pools have been scarcely more than one-third developed, and have greater potentialities than any of the present Oklahoma pools. In Oklahoma, pools of magnitude should

Jan 10, 1917

By J. W. Whitlow, P. K. Theobald, W. C. Overstreet

Monazite placers in a region of the Carolinas ex- in 1951-1954 by the USGS are estimated to contain at least 53,000 short tons of thorium and 4600 short tons of uranium. None of these deposits is being mined. The 5200-sq mile area investigated extends northeast along the western Piedmont from the Savannah River in South Carolina to the Catawba River in North Carolina. Much of the region is 700 to 1100 ft above sea level. Gentle hills and broad interfluves give a local relief of 100 to 200 ft. This increases to 1700 ft at the west margin of the area where the east flank of the Blue Ridge is approached in South Carolina and the South Mts. are entered in North Carolina. This report is restricted to placers in the Piedmont. Monazite deposits in the Blue Ridge and coastal plain were not covered by the investigation. Monazite Mining in the Carolina Piedmont: Discovered in 1879 by W. E. Hidden,' the monazite placers in the Carolina Piedmont were first mined in 1886. The area was a major world source for thorium and the lanthanides until 1895, when Brazilian monazite entered the trade. Total output from the Carolina Piedmont has been nearly 5500 tons of monazite,2 but the placers have been idle since 1911, except for 48 tons produced between 1915 and 1917. Monazite mining was revived in the Carolinas in 1954 when a dredge operated by the Heavy Minerals CO. opened a fluviatile placer along Horse Creek in the coastal plain near Aiken, S. C. Geology and Mineralogy: Two recent papers",' have described the geology of the monazite placer district in the Piedmont between the Savannah and Catawba rivers; the general geology of the region has been reviewed by P. B. King.' These reports show that the placers are in locally derived alluvial sediments that cover the floors of shallow, narrow valleys in an area underlain by monazite-

Jan 1, 1960

By N. A. D. Parlee

THE gas-liquid metal diffusion cell technique1-3 has been used to study the diffusion of nitrogen in Fe-C alloys. The actual apparatus and technique were the same as employed by the authors to study the diffusion of hydrogen in liquid iron.' The diffusion cell' was formed by immersing an alumina tube in a stagnant melt contained in an alumina crucible. The tube (hereafter called absorption tube) contained nitrogen gas at 1 atm and was connected to a sensitive gas-measuring system. The change in the average concentration of nitrogen in the melt in the absorption tube was determined by measuring the rate of absorption of nitrogen in the diffusion cell. Eq. [I], 1-3 derived from the appropriate solution of Fick's second law, was used to examine the data and to calculate chemical diffusion coefficients (D) in situations where the absorption appeared to be controlled by diffusion in the liquid: where V is the stp volume in cu cm, d is the diffusion cell diameter in cm, p, is the density of the melt in g per cu cm, pg is the stp density of nitrogen in g per cu cm, C, is expressed in wt pct, D is in sq cm per sec, and t is in min. According to Eq. [I], a plot of v vs vt should yield a straight line passing through the origin if absorption is controlled by diffusion in the liquid. The slope of this line could be used to determine the value of D under appropriate conditions. As discussed in earlier reports,1,2 the initial thermal expansion of the gas upon immersing the absorption tube distorts the line in the initial stages of a diffusion experiment. However, this is not a serious problem since the slope of V vs 6 plots can be determined from the data points obtained after the initial expansion ceases. The volumes reported on the data plot presented here represent absorption after this thermal expansion ceased. Several preliminary diffusion experiments were attempted with melts of pure iron and with Fe-C alloys containing up to 0.6 pct C. In these cases, no or very little absorption was observed. The only data obtained were for an Fe-C melt which was in addition thoroughly deoxidized by successive hydrogen and vacuum-degassing treatments. These treatments introduced an appreciable amount of aluminum into the melt and reduced its omgen content. The original charge material for this melt contained 0.23 pct s and approximately 0.001 pct &. After repeated hydrogen and vacuum-degassing treatments two diffusion experiments were performed. The analysis of the melt

Jan 1, 1968

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By J. J. Becker

Changes in magnetic properties with particle size are used to study the precipitation process in a Cu-Co alloy. In particular, the effect of a field during aging in producing anisotropy is shown to occur entirely during the growth of the particles, after precipitation is complete. HEAT-treatment in a magnetic field is done commercially to improve the magnetic properties of a number of materials. These can be divided into solid-solution alloys and precipitation alloys. The Permalloys are representative of the first type, and magnetic annealing greatly increases their maximum permeability. On the other hand, in precipitation alloys such Alnico 5 the important result is an increase in maximum energy product. The effect of the field in all cases is to bring about an additional magnetic anisotropy, uniaxial in nature, which makes the hysteresis loop more upright when measured in the direction in which the field was applied. The structural origin of the anisotropy brought about by magnetic annealing is not well understood. In the solid solution alloys, one possible explanation is based on ordering.' Another possibility is the orientation of like-atom pairs.' The precipitation systems known to respond to magnetic heat treatment are Alnico 2, in which the effect was first discovered," Alnico 5, cobalt ferrite (oxide),' and Cu-Co alloys.3 n these materials, the field affects the precipitation process itself in some way. Although there has been much work on Alnico 5. its nature is still incompletely understood. According to Geisler,' the precipitation reaction is of the

Jan 1, 1959

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948