Search Documents

By J. Versluys

A well can flow exclusively through the casing or exclusively through a tubing but can also flow partly through a casing and at the top part through a tubing. The main principles of the flowing of wells under these conditions were explained in the author's former paper.' Practically all factors that influence the regular flow are dealt with therein. The question of irregular flow, however, will be discussed briefly here. As a rule, an irregular flow must be avoided, as it may be assumed that the efficiency is thereby very small, while on many fields it is injurious to the sand of the oil-bearing layer. Periodical flowing often occurs with rising mixtures of gas and liquid. The phenomenon can be explained if it is accepted that two conditions are possible in the mixture; namely, the foam condition and the mist condition. If there is no stabilizer in the liquid, the foam condition can exist only when the liquid forms a greater portion of the volume than the gas. The mist condition, on the other hand, can exist only when the liquid occupies a smaller part of the volume than the gas. The foam condition occurs when there are gas bubbles in the liquid mass, while in the mist condition drops of liquid are disseminated in a gas-filled space. For sake of simplicity, it has been assumed that the mist condition prevails when 50 per cent. or more of the volume is occupied by gas, while with less than 50 per cent. gas the foam condition will arise. For distilled water and for oils which do not tend to form stable foams this is probably approximately true. If this does not hold good, however, two cases are possible: (1) The fields of the two conditions overlap or (2) they do not meet. If the fields of the conditions overlap there is an intermediate field where either of the two conditions can exist, depending on the history of the mixture. Suppose the foam condition prevails first and the gas

Jan 1, 1931

By M. E. Wadsworth, R. L. Pearson

THE dissolution of UO, in carbonate solutions can occur only il the tetravalent uranium is oxidized to the hexavalent state. The carbonate system is of particular interest because it provides a means whereby the oxidized uranium may be dissolved by forming the complex ion UO,(CO3)3-1. In the presence of oxygen the over-all reaction may be written UO+1/2O,4CO3T+2HCO2UO,(CO4)11+H2O [1] UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. The mineral ulrichite is the natural counterpart of the synthetic UO, used. The kinetics of the leaching of UO, should be similar for any of the uraninite type minerals. A pressurized system was used not with the hope it could be extended to commercial systems as a primary purpose but simply to provide the means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The importance of such pres-

Jan 1, 1959

By R. F. Mehl, M. L. Swanson, J. P. Hirth, G. M. Pound

The sorption of zinc in a-brass was investigated. By analyzing the elliPtically polarized light reflected from the surfaces of a-brass solid-vapor couples, their optical constants and surface compositions were determined. It was shown that the surface compositions approached an equilibrium value exponentially with time. The bulk diffusion coefficient, surface diffusion coefficient and condensation coefficient for a-brass solid-vapor couples were calculated near 350°C from the experimental results. It has been assumed during various diffusion experiments with bimetallic solid-vapor couples (Dunn,1 Seith and Kraus,2 Jenkins,3 Balluffi and Seigle,4 and others) that the surface composition of such couples reaches its equilibrium value immediately. Although this assumption is probably valid at elevated temperatures, it is certainly not expected to be confirmed at lower temperatures.* consequently, it was decided that a fundamental experiment, designed to solve this problem as well as to examine all aspects of bimetallic sorption, would be the investigation of the rate of approach to equilibrium of the surface composition of solid-vapor couples. The sorption (i.e., adsorption, absorption, and desorption) of metals is obviously dependent on the state of the metallic surface and substrate. Much recent theoretical8"9 and experimental10-12 work on condensation and evaporation of pure metals has shown that the surface contour in atomic dimensions is a critical factor in sorption, so that any deformation or contamination13,14 of the surface exerts a profound influence. It is also known that absorption or diffusion occurs much more rapidly along grain were and in other deformed regions. Thus an effective sorption experiment must utilize a strain-free and clean surface, or at least a clearly defined and reproducible surface state. A mechanically polished surface is in a highly deformed17-l9 state. Because the degree of this deformation is uncertain, it is clear that for most experimental purposes a strain-free (i.e., etched, chemically polished, or electropolished) surface is desirable. Although adsorbed gas molecules on metallic surfaces are unavoidable even in the highest vacuum,20 oxide films can in some cases be removed by suitable vacuum annealing. Electrolytically polished and annealed surfaces, being relatively without strain, smooth and free of bulk oxides, were considered adequate for the present sorption experiments. Measurement of the surface composition of a solid-vapor couple presents a unique problem. Since experiments to determine the approach to equilibrium of the surface composition must be performed at temperatures where diffusion is very slow, solute penetration is so small that conventional analytical methods are unsuitable. An optical reflectivity method utilizing a polarization spectroscope was employed because of the relatively small penetration (~200A) of visible light in metals. By this method, elliptically polarized light reflected from the metal surface was analyzed and compared with that reflected from samples of known composition. The a phase of the copper-zinc system was

Jan 1, 1962

By G. G. Waddell, T. J. Crocker, S. S. M. Chan

A successful engineering structural design often depends upon a thorough understanding of the material properties of the structure. It is no exception when designing a supporting system for stable underground openings. For this reason, studies were made in the deep mines of the Coeur d'Alene mining district to obtain engineering properties of rocks and rock masses immediately surrounding underground openings. In this paper, data concerning laboratory tested physical properties of rocks and in-situ deformation behavior of rock masses from the Galena, Lucky Friday, and Silver Summit mines of the district are presented. Interpretations of the data so obtained and suggestions for the use of the results of the investigations as design criteria are also outlined.

Jan 1, 1973

By F. P. Dewey

The first systematic attempt of the National Museum to gather material representing the economic geology and metallurgy of the country was made in connection with the Centennial Exhibition. The department may be considered as having originated then, althongh it was not formally inaugurated until December, 1882. Previous to the Centennial, all the illustrations of economic geology had been included in the mineral collection, and the illustrations of metallurgy were so very few that they had also been included with the minerals. When the museum began its collections for the Centennial, the subject of the mineral resources of tile United States was placed in the hands of Professor Wm. P. Blake, who was eminently fitted to undertake the work by his experience at various international exhibitions and his extensive acquaintance with the mining industry of the country. Professor Blake prepared a broad and exhaustive plan for this purpose, and the very large collection shown at Philadelphia was well calculated to set forth the vast mineral wealth of the country. The history of the department proper may conveniently be divided into three periods : first, the formative period, during which the Centennial material was mainly administered upon, ending Jnly 1, 1884, with the beginning of the preparation for the New Orleans Exposition; second, the New Orleans Exposition period, from July 1, 1884, to June 30, 1887, during which the collections for the New Orleans Exposition were made, exhibited at New Orleans, returned to Washington, and installed permanently in the museum; third, the southwest-court period, from July 1, 1887, to October 1, 1889, during which the collections were arranged in the southwest court of the museum.

Jan 1, 1891

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By O. Vartiainen, R. T. Hukki

A preliminary investigation of the collecting effects of various fatty acids in tall oil has led to a conclusion that the collecting power of fatty acids used in flotation increases with increasing unsaturation of the hydrocarbon chain, Linoleic acid was found to be an excellent collector for oxide minerals.

Jan 8, 1953

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By Jean-Jacques Prompsy, J. S. Rinehart

The purpose of the present study was to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the drill bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. This paper covers one phase of a broad study involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, arange commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a velocity range in which the dynamic effects are greatly exaggerated and made more identifiable. Specifically, fracturing which develops at the end of a cylindrical bar undergoing a shock produced by impact was experimentally investigated, the impacted area being the face of a truncated cone terminating the cylindrical bar. Fracture characteristics were looked at as a function of impact velocity, area of impacted face and cone angle — parameters of considerable importance in the design of drill bit. EXPERIMENTS The specimens were made of Plexiglas, which enabled the fracture pattern to be easily observed. In Plexiglas, the velocity of a longitudinal wave is about 8,700 ft/sec, and the velocity of the transverse wave about 4,200 ft/sec. The specimens were impacted by a steel cylinder whose lower face was parallel to the terminal face of the experimental bit, as shown in Fig. 1. The impacting mass was shifted up and down on two steel rods, dropping from a maximum height of 11 ft, with the velocity varied between 0 and 6.5 m/sec. The initial mass of the cylinder was 4.1 kg, which could be increased by steps up to 8.8 kg by addition of steel plates. The velocity of the steel cylinder was determined by using an electric circuit; as the cylinder dropped, it contacted two steel wires, the first one starting and the second one stopping an electronic counter. Two similar counters connected in parallel were used to corroborate each other. The velocity was checked at each drop as it had been observed to vary somewhat from drop to drop. The two contact wires were located just above the top of the specimen so as to give a value of the instantaneous velocity of the steel cylinder at impact. The distance between the wires was 40 ± 0.5 mm and the discrepancy between the counters was never more than 0.1 m/sec. Thus the velocity was known to within 3.25 per cent. This precision was sufficient with respect to the precision of the machining of the specimens. A very small lack of parallelism between the face of a specimen and that of the impacting hammer resulted in an oblique impact which required a much lower velocity to break the specimen. The experiments had a twofold purpose — (1) to observe the fracture pattern, and (2) to find relationships between the minimum velocity required to generate a fracture within a specimen and the

By H. Brandhorst, C. G. Dunn

THE main purpose of the present note is to provide further information on the effect of orientation on strain-induced grain boundary migration in sheet material. A secondary purpose is to draw attention to the presence of a possible (hkl) dependent surface energy driving force, when the two grains of a bicrystal specimen have different (hk2) planes at the gas-metal interface, and to suggest means of eliminating this effect from the strain effect. If two grains A and B of a bicrystal have specific surface energies ? A and ? B respectively, there exists a driving force for grain boundary migration equal to 2(? B - ? A)/t, where t is the thickness of the specimen.' When t is quite small and the residual strain energy densities €A and €B of grains A and B, respectively, adjacent to the boundary are nearly equal, it is possible that the surface effect may be larger than the strain effect. he difference € B - € A gives a driving force per unit area of grain boundary due to an applied strain.)2 However, with increasing t the surface effect decreases while the strain effect presumably remains constant. Therefore, at some sufficiently large value of t, it is possible to ignore surface energy driving forces.* On the other hand, the surface effect is eliminated for all value of t when both grains have the same (hkl) orientation or have identical values of surface energy. Although the previous study provided information on the effect of orientation on strain-induced erain boundary migration,' no orientations with the (100) plane in the plane of the sheet were included. The present paper provides information of this kind. A seed crystal reorientation technique4 was used to prepare a large bicrystal of silicon iron (3 1/4 pct Si) consisting of two (100) grains in the (100) [001] and (100) [Oil] orientations. After a cold rolling strain (7 pct reduction to 3/4 mm final thickness), small specimens were prepared as before2 and then annealed in hydrogen. The boundary migration was such that the grain in the (100) [011] orientation always grew. After overnight anneals at 1100° or 1000°C, none of the initial (100) [001] grain remained. An anneal of 30 min at 950°c, however, provided information on the start of boundary migration. Fig. 1 shows both the initial position (lower line) and the final position (upper curved line) of part of the boundary, as revealed by thermal grooves. In a different area, part of the final boundary was not revealed by thermal grooves; the rate of boundary migration presumably was too high for the growth front to be defined by the time dependent thermal grooving process. In another area there was a vacated intermediate position connected to the initial position of the grain boundary. This indicates that only part of the boundary

Jan 1, 1962

By Zhengbo Pan, Fujun Gou, Jifei Chen

This paper discusses the various alternatives that are technically feasible for "over-the-raise" continuous advancing in gently inclined coal seams and the computer-aided selection of the optimal mining option. Examples in Wangshiao Coal Mine and Chaohua Coal Mine are cited to illustrate the interval between raises, face length, single or double raise layout and single or double face layout.

Jan 1, 1983

By E. H. Crabtree, T. G. Chapman, V. W. Winters

This paper traces the experimental and pilot plant work completed by the authors since 1939 including the various methods which have been developed in applying coarse activated carbon to cyanidation. The methods and results developed by the authors in desorbing gold and silver from carbons are given and the possibilities for the re-use of the desorbed carbons are discussed.

Jan 2, 1950

By T. S. Lundy, J. I. Federer

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystalline thoria.

Jan 1, 1962

By N. H. Mannakee

[Secretary's Note.—At the Spokane meeting of the Institute, in discussion of President Brunton's address on "Modern Progress in Mining and Metallurgy in the Western United States," and at the request of members present, Mr. Ayres gave an oral account of his new separator, which is here published as an independent paper, partly because of its inherent importance and partly because it describes an improvement which did not originate in the Western United States, and therefore does not fall, strictly speaking, under the title of President Urunton's address.—R. W. R.] A brief history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name "breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the " breaker-boy " as a slate-picker, with his ever-increasing capriciousness. As the richer veins or a splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities, particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complicatioii yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Jan 1, 1910

By Y. Nakahiro

The removal of heavy metal compounds from a synthesized waste cyanide solution is achievable by a precipitation-flotation method. However, the differential separation of constituting metals by this method was thought to be very difficult. The present author found that addition of ferrous salt to the synthesized waste cyanide solution of cadmium and copper can modify the separation characteristics of these metals. In this paper, the separation of cadmium from copper in the synthesized waste cyanide water by the precipitation-flotation method is discussed. This differential flotation uses ferrous salt as a precipitant and sodium oleate as a collector. Based on a series of fundamental flotation tests, actual differential flotation tests were made. The separation of cadmium from copper in the synthesized waste cyanide water was found to be satisfactory. This method can be effective for the removal of difficult-to- separate colloidal precipitates from liquids by the sedimentation method, provided the applicability of this method to the separation of the other metals is promising. This consists of the intensive studies which have been conducted at author's laboratory.

Jan 1, 1980