Search Documents

By S. C. Geol, C. H. Page

INTRODUCTION Mining at Mindola Mine, Rokana Division of Nchanga Consolidated Copper Mines Limited is the deepest on the Zambian Copperbelt. Mining extends to 1150 metre depth so far and the present plans extend to 1500 metres, although reserves exist below this level. Mindola Mine is the major producer of copper/cobalt ore at Rokana Division and produces approximately 200,000 tonnes of copper/cobalt ore per month. A standard open stoping method is the only method used for mining with minor variations in positioning drilling drives and other development, figure 1. The standard main haulage interval is 75m but in flat dipping areas the full stope height is split into two or three panels. In 1970 severe mining problems were experienced when mining deeper than 850111 below surface. The main problems included: - Heavy support requirements in drilling drives near stope face. - Premature closure of blast holes necessitating pre-charging of the holes with explosives immediately after drilling and well before the day of blasting. - Severe bumping and spitting due to rock movements on drive surfaces and remotely within the rock mass under high stress. - Low mining efficiency due to dilution from the waste hangingwall. - These stress related factors also caused some premature detonations of precharged but unprimed blast holes which became a serious safety hazard. A number of alternatives have been considered to overcome these problems. A search for leas sensitive explosives to avoid the premature detonation problem has been partially successful, however, the need for a method of reducing stress levels at the mining face is still considered essential as the mine goes deeper. This paper describes experiments with Regional Support Pillars as a method of reducing stresses at the mining face.

Jan 1, 1981

By Walter Renton Ingalls

IN SEVERAL papers and addresses during the past two years, I have dwelled upon some of the economic consequences of the war. The fundamental thought that I have sought to convey is that the world became immensely poorer by the war, not only in material wealth and population, but also in the psychology and morale of the people. I do not see how there can be any intelligent dissent from that statement. All the ideas of post-war prosperity were manifestly fallacious, manifestly fallacious from the outset. If there had been any truth in them it would have followed logically that a great war, with all its destruction of wealth, health and life would be a good thing. Therefore, let us have a great war every ten years or so. Such an idea would be both monstrous and absurd. Assuming then the acceptance of my premise, I have tried to show that the losses by the war could be made good in a short time, i.e., in a relatively short time, only by doing things a great deal better than formerly, and that the accomplishment of such a result called for greater transparency in industry, for industrial cooperation, for thinking in terms of industries as a whole, and for the greater exercise of engineering functions. All of this introduced, of course, the position and psychology of labor. I say frankly that I do not look for labor to contribute any constructive thought to the upbuilding. I neither expect it nor hope for it. This is a pity, for it could do so much for its own economic advancement if it would. However, it never has done so, but rather has benefited only from the exercise of the talents of the few, and the main hope now is to bring it into a passive state, dispelling the resistive fallacies that developed during the war. Let us briefly examine the nature of these.

Jan 1, 1921

By Olin M. Hart

Uranium ores occur in the Lower Cretaceous Inyan Kara group of heterogeneously stratified fluvial and fluvial-marine sandstones in the Black Hills of western South Dakota and northeastern Wyoming. There are three principal mining districts, each in the ancestral and present drainage area of a major river partially responsible for stripping the region to its present topographic form. Primary minerals in the deposits are coffinite and uraninite with minor amounts of paramontroseite and haggite. The ore minerals coat sand grains and fill interstices of complexly cross-stratified sandstone along solution fronts similar to "roll" type deposits of the other districts. Minerals of oxidized deposits are typically carnotite and tyuyamunite with different proportions of secondary vanadium accessory minerals. Ground water was the transporting medium and deposition of primary uranium and vanadium minerals occurred in reducing environments produced and controlled by physio-chemical characteristics of the sedimentary rocks.

Jan 1, 1968

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945

By William B. Hughes

The rubber-sleeve core barrel was developed to improve core recovery from unconsolidated sands, where it is most difficult to obtain cores with conventional barrels. The use of a rubber-sleeve core retainer, together with other departures from clsual design, has required a considerable amount of testing to prove its op-erability. Tests run in shallow experimental holes and in drilling wells in the U. S. and Vemzuela have, to a large extent, proved the operation of the barrel. Internal mechanism troubles, such as sandbinding of the sleeve, have been largely overcome. Cores have been recovered from completely unconsolidated sands where conventional coring has almost been abandoned because of poor recovery. In addition to retaining the core until brought to the surface, the barrel gives a "packaged-ar-cut" core, which is coilverzient for handling and transportatiorz. In the initial work, drag blade cutters, roller cutters, and tungsten carbide insert cutters were usrd for cutting unconsolidated sands. Further bit head development is presently being conducted using diamond heads in unconsolidated sands where shaler, hard sands, and limestones are encountered in adjacent formations. Thir work should render the barrel capable of cratting and recovering most types of formations, possibly including broken and frac- tured fornlations. This development is being carried on in cooperation with a diamond bit manufacturer. INTRODUCTIO N For many years the oil industry has needed greater recovery of cores from unconsolidated formations. Conventional equipment has been used to core unconsolidated sands with little success. Specifically, a core barrel was needed which would recover unconsolidated sands in a condition that would give useful reservoir information. DEVELOPMENT OF 'THE RUBBER-SLEEVE CORE BARREL Basic Requirements of Unconsolidated Sand Corino The basic need was defined as a core barrel that would obtain a continuous unconsolidated core with sand grains in place as deposited in the formation. A preliminary survey of coring equipment and search of the literature pointed out the weaknesses of conventional core barrels. Laboratory tests using unconsolidated sand in a metal tube simulated actual sand movement into the core barrel during conventional coring. In conventional barrels the core sometimes crumbles and bridges, or fails under compressive column action, becomes oversize, and wedges against the walls of the inner barrel. The core barrel requirements established by the surveys and preliminary tests are as follows. 1. The core should be held to- gether as it is cut so it cannot crumble and bridge against the walls of the coring tool, care being taken not to permit damage from fluid circulation. 2. The core should be continuously supported as it is cut so it will not have to support itself in compression. 3. The core should be packaged in the barrel to retain an undisturbed condition during the trip out of the well. The packaging should be such that the core can be removed from the barrel and shipped to the core analysis laboratory without physical disturbance or alteration of fluid content by exposure to the atmosphere. Operation of the Rubber-Sleeve Core Barrel The rubber-sleeve core barrel (Fig. 1) meets the basic requirements for the recovery of unconsolidated sands.

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By AUDLEY H. STOW

I. INTRODUCTION. THE general drift of the discussion as to the relative merits of pressure- and exhaust-fans has resulted, if we may judge from the prevailing practice, largely in favor of the latter. The subject has been hitherto treated, however, with special reference to highly gaseous mines, the effect of the form of ventilation upon dust-explosions having been too little considered. Even in mines containing practically no gas, dust-explosions may occur; and if, as I believe, pressure-fans are to be preferred for their effect upon dust, it may be worth while to reopen the debate, and to challenge the advisability of exhaust-ventilation under certain conditions. There are several forms of colliery-ventilation, which may be described as follows: Plain or simple pressure-ventilation, in which the fan acts as a pressure-fan, and the movement of coal is unobstructed at the surface by doors or equivalent devices in drifts or shafts, the traveling and haulage thus being in the return-current. Plain exhaust-ventilation, in which the fan acts as an exhaust-fan, the movement of coal being likewise unobstructed at the surface, and the traveling and haulage being in the intake. Obstructed pressure-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the intake. Obstructed exhaust-ventilation, in which the movement of coal is obstructed at the surface, in order that the traveling and haulage may be in the return. The apparent advantages in running a fan "pressure" during working-hours, and " exhaust" between shifts, seem to justify the recognition of this combination as a standard form of ven-

Feb 1, 1909

Jan 1, 1882

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37' substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By Charles H. Jacoby

The solution mining of evaporites has a history of approximately 5,000 years. The insitu leaching of metalliferous ore will have many of the same characteristic problems which have confronted industry for years in the production of evaporite minerals. Basically we will be converting the less soluble forms of valuable metals into their more soluble salts and producing these in much the same manner as, for example, sodium chloride. There are a number of problems which we are faced with that are more complex and complicated and, therefore, will require a higher degree of sophistication than previously employed. One of our most important undertakings will be the clearcut definition of the problems involved. While a great deal of expertise can be drawn from the solution mining of evaporites and the oil industry, problems peculiar to the hydrometallurgical field will need to be solved. One of these is the introduction of permeability into an impermeable rock so as to expose the sought after values of metals which by volume are infinitesimal when compared with sodium chloride, potash or other type water soluble mineralization. After establishing this permeability which will be miniscule when compared to a solution cavity, there will be the maintenance of this permeability. In general, salt deposits are of a somewhat uniform chemical composition and thus their chemistry was relatively simple. Each metalliferous ore body is somewhat unique in its chemistry and will need to be treated accordingly.

Jan 1, 1974

By John Langton

In determining what kind of pourer should be adopted for the works of the Moctezuma Copper Co. at Nacozari, Sonora, Mexico, certain considerations imposed by local conditions had to be taken into account. Water.—During most of the year the water-supply is abundant for all purposes, but it dwindles rapidly when the dry season sets in, reaching a minimum flow which is entirely undergrouad. It was evident, that with the greatest care in keeping down the unavoidable loss of water in milling and smelting, these operations and hence the capacity of the works mould ultimately be limited for about two months of the year by the small watersupply available at the period of minimum flow. Transportation.—The nearest railway terminus was in Arizona, at the international boundary-line; and the price of supplies at that point would be enhanced at Nacozari by the additional cost of a 90-mile wagon-haul. During the rainy season, transport to Nacozari was much impeded, and at times made impossible, by the condition of the roads. Hence, to insure continuous operation at the works, it would be necessary to provide for hauling the year's supplies, including fuel for power and coke for smelting, in less than eleven months. In other words, the average freight delivered daily at the works should be at least 10 per cent. more than the average daily consumption. For moderate quantities of freight, pack-carriage by burros is astonishingly cheap. But it has a capacity-limit which is generally very soon reached. A 200-lb. load, and 10 miles a day, 5 with and 5 without load, is the full capacity of a burro. This means one burro per ton-mile of the round trip; and,

Jan 1, 1904

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period April 1 to 15. William B. McKinley, New York, N. Y Collier Cobb, Chapel Hill, N. C. C. W. Goodale, Butte, Mont. E. P. Fleming, Guayacan, Chile. D. C. Brown, San Luis Potosi, Mex. Albert Sauveur, Cambridge, Mass. W. H. Rettie, Yonkers, N. Y. H. M. La Follette, La Follette, Tenn. Mark B. Kerr, San Francisco, Cal. E. Fleming L'Engle, New York, N. Y. H. W. Turner, San Francisco, Cal. H. Garlichs, St. Louis, Mo. Frank M. Leland, Mackay, Idaho. Henry Hay, London, England. Sir Robert Hadfield, London, Eng. Edward J. Way announces that his agreement as consulting engineer in South Africa for the Anglo-French Exploration Co., Ltd., having terminated, he will engage in professional consulting work with headquarters at 135 Cullinan Buildings, Simmonds St., Johannesburg, South Africa.

Jan 5, 1914

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;'-' and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

RACAL COMMITTEE OF ARRANGEMENTS Henry McCormick, Chairman; David Watts, Secretary; H. H. Campbell, A S. McCreath, S H. Chauvenet, C. E. Stafford, George S. Comstock, Jones Wister, E. C. Felton, F. W. Wood, Harvey Fisher. CITIZENS' RECEPTION COMMITTEE Governor H. M. Hoyt, Hon John C. Herman, Hon Simon Cameron, Hon. J. D. Cameron, W T. Hildrup, Charles L. Bailey, W. W. Jennings, Lane S. Hart, H. U. Carter, Gilliard Dock, T. T Wierman, Jr, James Boyd, D. L. Jauss, Dr. T J. Dunott, S. C. Gilbert. William J Rose, James Lynah, Dr. H. B Buehler, William N Lamberton, John Wister, G. M. McCauley, David Fleming, John Q. Donney, M. E. Olmsted, H. S Gross, Henry Gilbert. John B. McPherson, Lyman D. Gilbert, F. W. Forman, L. S. Bent, A. J. Dull, F. R. Leib, Dr. G. W. Belly, James McCormick. The opening session of the meeting was held in the hall. of the Young Men's Christian Association, on Tuesday evening, October 25th. Mr. Jones Wister, of the Local Committee of Arrangements, introduced the Hon. John C. Herman, mayor, who, in a brief address, extended to the members present a welcome to the city, of Harrisburg ; Lieutenant Governor Stone made an address of welcome on behalf of Governor Hoyt and the Commonwealth of Pennsylvania. President Metcalf responded, on behalf of the Institute, to the cordial addresses of the mayor and lieutenant-governor. The following persons proposed for members and associates of the Institute, and recommended by the Council, were unanimously elected :* MEMBERS. William F. Aldrich, - Montevallo, Shelby Co., Ala. George H Blake, - Steelton, Dauphin Co., Pa. L. Bertram Cady, - Salisbury, N. C. John B. Church, - Pottsville, Pa. Walter S. Church, - Pottsville, Pa, Frank L Clark, - Pittsburgh, Pa. * In the following list are included those elected at a subsequent session of this meeting.

Jan 1, 1882

By R. E. Wagner

MISSOURI's famous lead area, in what is known as Southeast Missouri, is locally termed the "Lead Belt." These deposits are in the Bonne Terre dolomite of late Cambrian age which has a thickness of nearly 400 ft. Underlying this is the La Motte sandstone which varies in thickness from 0 to 400 ft. The La Motte beds are deposited directly on the ancient erosion surface of Pre-Cambrian porphyries and granites of probably Algonkian age. The buried igneous peaks extend up into the Bonne Terre in several areas within the Lead Belt. Overlying the Bonne Terre are shales and siliceous dolomites of late Cambrian and early Ordovician age. Within the Lead Belt these have a thickness of from 0 to 500 ft. The district is bounded in general on the southwest by the Sims Mountain fault, on the northwest and north by the Big River fault, and on the

Jan 1, 1947

By Edward H. Robie

PONCA CITY proved an ideal selection as a place of meeting for the Petroleum Division this fall. The accommodations at the Conoco Club were just what was required for such a gathering; the committee having the arrangements in charge functioned with the efficiency of veterans and the enthusiasm of neophytes; and the members and guests followed the speakers with close attention, entered the subsequent discussions with gusto, and divulged the "low-down" at private conferences. No one minded the drizzling rain on the first day, which only served to keep up the attendance in the auditorium; the weather then cleared up in time for a group picture before the gathering went their separate ways.

Jan 1, 1932

By Joseph E. Pogue

FOR a number of years the petroleum department of The Chase National Bank has been making a continuing study of the financial aspects of thirty oil companies. (See Pogue and Coqueron, "Financial Analysis of Thirty Oil Companies," pamphlet, The Chase National Bank, November 1945, for data covering eleven years, 1934-1944, and the list of the companies making up the group. See also "Capital Employed in the Petroleum Industry," by the same authors, M&M, November 1944.1 This group represents a large sample of theAmerican petroleum industry, covering about two thirds of the business. Certain aspects of this study concern the capital employed in crude oil production, the main features of which arc presented in this paper.

Jan 1, 1946

By E. J. Kenaedy, E. H. Robie

THOUGH the fall meeting of the Coal Division was held in the heart of the anthracite section, at Hazleton, Pa., the bituminous industry was well represented also, and the two groups found much common ground for discussion. The' technical part of the program was confined to two sessions in the morning and afternoon of the first day, Friday, Oct. 14, the evening and the following day being reserved for field trips and social functions. The attendance more than met the expectations of those in charge of the arrangements; there seemed no hint of depression here.

Jan 1, 1932

By Robert Glass Cleland

THE DEATH of William E. Dodge occurred at a time when, all unwittingly, the company in which he had so long been the dominant factor was about to break with its old practices, its old traditions, its old interests, and transfer its major activities three fourths of the way across the continent and engage in an enterprise that differed almost as much from the original Phelps Dodge undertakings as the rough, arid mountains of the new region differed from the green hills and valleys of New England. To understand the effect of this transformation upon the fortunes of Phelps Dodge, one must change the setting of the present narrative from the familiar locale of the Atlantic seaboard to the land of "distance, silence, and solitude," that men called Arizona. In 1880 that Territory was one of the last frontiers of the Old West. To the Spaniards it had been a land of mystery and fable, the limit of the King's settlements, the far edge of the rim of Christendom. Through it Coronado; in a vain effort to find the fabulous Cities of Cibola, had led "the most brilliant company ever assembled in the Indies to go in search of new lands." Below its southern border, Father Kino, the "steel-thewed" Jesuit described by his

Jan 1, 1952

By AIME AIME

DURING the morning session," on Feb. 17, papers were presented and discussed regarding a recent wire saw installation, cement rock quarry operations, hydration factors in gypsum deposits and the status of the phosphate industry of the West. Oliver Bolvles presided and there were about twenty-five members present. W. M. Weigel's paper (T. P. 262), "The Application of the Wire Saw in Marble Quarrying," was read by the author. He described the recent installation of the St. Clair Marble Co., near Guion, Ark. Since the use of the wire saw for quarrying is comparatively new and the fact that it has been almost entirely limited to slate quarries heretofore, ?he description and data given in this paper were of much interest.

Jan 1, 1930