Search Documents

By Dudley L. Davis, E. C. Peterson

Introduction The Darwin District is 30 miles east of Olancha which is 220 miles north from Los z4ngeles via U. S. Highway No. 6. The ore deposits occur in the Darwin hills that have been elevated above the Darwin plateau by typical basin and range-type faults. Some of these faults have been active quite recently as shown by the displacemerit of Quaternary (?) basalt flows and the rejuvenation of erosion in Darwin wash. The ore bodies occur as fissure fillings and replacement of favorable beddings in a thick series of Paleozoic limestones, dolomites, shales and quartzites. Rich oxidized lead-silver ores were dis'Overed in the early seventies. BY 1875, Darwin had a population Of about 5000, and by 1880 several small mills and smelters had been built. Early exhaustion of surface ores, the isolated location of the district, and fluctuation Of metal prices caused intermittent operations until World War 11. The district production is estimated at about $3,000,000 prior to 1900 and perhaps $4,000,000 between 1900 and 1945 when Anaconda purchased the major producing mines. 'or the Past two Years, daily production has averaged 75 tons of direct shipping and 150 tons of milling-grade ore. At present, 300 tons of mixed oxide and sulphide ore are treated by flotation, the oxidized lead minerals being activated by addition of sodium sulphide after galena and sphalerite have been recovered from the circuit. Extraction averages 85 pct of the lead, 80 pct of the silver, and about 33 Pct Of the zinc in a bulk concentrate. The mill is designed so that minor changes permit selective flotation of pyritic lead-zinc ores encountered at depth. General Geology The oldest rocks in the Darwin hills are a series of Paleozoic limestones, dolomites, shales and quartzites probably pennsyl-vanian in age. These rocks have been intruded on the Rest by the Coso granite batholith and on the east by a granodiorite stock. Numerous sills and dikes grading from orthoclase granite to gabbro are exposed in the underground workings. The sedimentary rocks have been considerably folded and faulted, the most prominent structure being a northwest pitching anticlinal fold, the crest of which lies just west of the ridge line of the Darwin hills, The east limb of this fold has been intruded by the granodiorite stock and east of the stock the sediments show several closely spaced anticlines and synclines. The minor flexures on the west flank of the major fold are structurally important in localizing the ore in the Defiance and Essex mines of the Darwin group. There are three principal systems of faulting and fissuring, most of which are post-intrusive and premineral in age, with minor amounts of postmineral movement. The Darwin tear fault is the largest, most persistent fault in the district. It strikes N 60 to 75°W, dips steeply south and is traceable for about 10 miles. It is a normal

Jan 1, 1949

By Eldred D. Wilson

Apropos of metals low in the series illustrated by Dr. Butler's Table II, it is interesting to note that Cress and Feldman reported traces of platinum metals in several samples of alunite. They found, chemically and spectrographically, several traces of platinum, palladium, and rhodium in alunite from Sugar Loaf Peak, near Quartzite, Ariz.; silver, platinum, and rhodium in alunite from Rio Grande County, Colorado; and traces of rubidium and gallium in various samples of alunite. These authors stated that the platinum metals appear to be present as oxides and suggested deposition by hydrothermal solutions under near-surface conditions.

Dec 1, 1956

By W. B. Plank, A. C. Callen

WAR and normalcy do not walk hand in hand, whether it be in industry, the educational field, or in the daily lives of individuals. Schools and departments offering curricula in mineral engineering have been seriously disrupted, beginning with 1942 and reaching a low during 1944. Selective Service regulations and voluntary enlistments have effectually stopped the flow of college-trained men into the mineral industry, and the flow into the colleges is little more than a dribble. The year just closed has been a most serious one for our institutions. Until March many of our faculties had been kept reasonably intact because of the large training programs of the Army and Navy. Although the number of

Jan 1, 1945

By W. C. Leslie

W. C. Leslie (Edgar C. Bain Laboratory for Funda mental Research)—This investigation, with its com bination of high-purity metal, calorimetry, and metallography, will serve as a model for annealing studies for a long time to come. The evidence for a competition between recovery and recrystalliza-tion is particularly convincing. The demonstration of edge-nucleated recrystallization was so clear that it may obscure the necessity for other types of "nucleation" sites; otherwise, single crystals of aluminum could not be recrystallized after cold work. At least three types of sites have been found to operate in iron: 1) high-angle boundaries, probably in the same manner as in aluminum, 2) matrix sites, 3) inclusions or second-phase particles. In each instance, the cells developed during cold work and perfected during recovery are the "nucle for recrystallization. Observations by ourselves and others of the dislocation structure of cold-worked metals and of the structural changes that occur during annealing have led us to doubt the validity of the basic assumption of the Lucke-Detert theory, and of the modification developed by Gordon and Vandermeer, that during recrystallization of a metal containing foreign elements in solid solution a high-angle boundary is ad vancing into a cold-worked matrix having a random distribution of solute atoms. We contend that an es sential part of the cold-working and annealing of solid solution alloys is the trapping of solute atoms by the low-energy "wells" afforded by individual dislocations and by dislocation arrays. If cells are formed during cold work, the cell walls are stabilized by this concentration of solute atoms. Thus, solutes inhibit recrystallization not only by decreas-ing the rate of high-angle boundary migration, but also by preventing the formation of high-angle boundaries by subgrain growth or coalescence, i.e., solutes can inhibit both "nucleation" and growth. In addition to stabilizing the dislocation Structure, the solute-dislocation interactions may produce clusters of solute atoms which are not as readily assimilated into the recrystallized grains as are individual solute atoms. There is an additional complication. The dislocation structure formed upon cold working a dilute solid solution may not be the same as that formed during cold working of the pure solvent metal. The solute can either enhance or minimize the formation of cells during cold working. Both effects have been observed in binary alloys of iron. The annealing process is inextricably connected with the mechanisms of strain hardening and solid solution hardening. Although the correlation between experimental boundary migration rates and the predictions made from the theoretical equations are impressive, it should be mentioned that in at least four other instances (Pb-Ag and pb-Au,15, Fe-Mn,16, Fe-Mo)17 the agreement was rather poor. In brief, while it is probable that the migration of high-angle boundaries is held back by solutes in the manner described, this is only a partial explanation of the total effect of solutes upon recrystallization of cold-worked alloys. Paul Gordon and R. A. Vandermeer (author's reply)— The authors first wish to thank Dr. Leslie for his compliments of this work. It is perhaps worth pointing out that some of Dr. Leslie's remarks are directed toward subject matter covered in two earlier papers in our work.18,19 We agree with Dr. Leslie's main contention that the exact nature of the metal structure in the vicinity of a boundary should have an effect on the boundary migration. The theory of Lucke and Detert does not take such detail into account, nor does it account for orientation effects on the migration rates. We assume that since our data checks the theory so well, the effects of detailed structure are statistically averaged out by the polycrystalline techniques used just as are the effects of orientation factors.

Jan 1, 1963

By E. B. Thornhill

Discussion of the paper of E. B. THORNHILL, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1653 to 1670. D. B. HUNTLEY, Oakland, Cal.-About 15 years ago it chanced to be my lot to cyanide some mill tailings, assaying about $5 per toll in gold and, a few cents in silver. It was in southern Idaho, a. desert region where costs are nearly as large as in central Nevada. We knew that we had a lot of tailings that had been amalgamated and contained about 1 lb. of quicksilver per ton. We knew that we would dissolve some of the quicksilver when we cyanided them with say 0.25 per cent. cyanide solution. We figured (optimistically) that the cyanide would dissolve all of the quicksilver, and we thought to capture all of that, 1 lb. per ton; and we figured out profits as partly gold, partly silver, and partly quicksilver from the recovery in working those tailings. Actually, however, we did this: We had a battery of three large, old-fashioned silver-mill retorts. We retorted our zinc-dust precipitate, recovering about ¼ lb. of quicksilver per ton treated. That was only a loss of 75 per cent. of what we originally had, but still it was profitable by virtue of the conditions. I mention it partly to call attention to the crude old way of doing it, and partly to call attention to how chemical methods for recovering quicksilver have developed in the last 15 years.

Jan 12, 1915

By O. H. Banes

The electrolytic zinc plant of the American Zinc Company located at Sauget, Illinois started operations in April 1941. The plant had a designed capacity of 45(T) per day. The original flow sheet was quite simple, incorporating the low density process. Through the years the capacity of the plant has been increased to the current design of 214(T) cathodes per day. This paper describes the current operation along with typical metallurgical data.

Jan 1, 1970

By Wilson B. Emery

The Hidden Dome gas field, situated in Washakie County, Wyoming, was discovered Sept. 26, 1917. Subsequently five additional gas wells were completed and a large reserve was developed. For a number of years this field completely supplied the domestic market at Basin and Greybull, as well as the refinery at the latter town, and it is still supplying gas in small amounts to this market. Production is obtained from the sands of the Frontier formation at depths ranging from 1000 to 1500 ft. The original rock pressure was 725 Ib. and initial production ranged from 4,000,000 to 28,000,000 cu. ft. per day per well. Porosity of the sand, determined from the size of the productive area and the amount of gas recovered, is over 18 per cent. Area and Management It is estimated that the productive area is about 640 acres. Its outline is indicated on Fig. 5, on which are also shown the locations of holes drilled on the structure and the area of unit operation. The unit area is owned by the Ohio Oil Co. and development and operation have been by this company. No productive well has been completed outside this area. The entire area was Government land filed on under the placer mining law. Results of Unit Operation With six producing wells, or an average of one to each 160 acres, the pool is completely developed. Location of the wells was made with respect to structural conditions plus the requirement that at least one well be drilled on each 160-acre placer claim. Perhaps a somewhat more uniform spacing of the wells might have been accomplished and one well eliminated, but it must be borne in mind that the holes, on account of their shallow depth, were not expensive and that the object was to develop as reliable a reserve as possible. There is no cause to suspect that these holes have not adequately drained the reservoir and there is every reason to think that any additional wells, which might have been drilled under diversified ownership and operation, would have been an economic waste. Unit operation by a competent company has not only resulted in the elimination of loss of gas through careless development and operation

Jan 1, 1930

By L. D. Lash, J. R. Ross

Scandium is a pseudo-rare earth which is truly rare and expensive. It has special properties which may make it desirable even at the present price of $2750 per lb. Recently the price was lowered from $5000 per lb which had prevailed since 1952, and it is anticipated that usage will be stimulated because of the lowered price. This metallic element is distributed widely in trace amounts in the rocks of the earth's crust. In addition to micro-amounts found in most uranium ores, concentrations of 50 to 100 ppm have been found in Colorado ferberite ore, lateritic nickel ore, heavy sandstone from Utah, Wyoming, and New Mexico, and various zircon sands and monazites from the western part of the US. Scandium has been found as an essential constituent of very few minerals, the most important being thortveitite, a scandium silicate. At the present time, this mineral commands a price more than twice that of gold.

Jan 8, 1961

By Ivan B. Cutler, Milton E. Wadsworth

Coprecipitation of anionic and cationic polyelectrolytes has been applied to floccula-tion of several mineral systems. Results obtained in a study of the flocculation of kaolinite and hematite suspensions of polycationic and polyanionic electrolytes are presented. Greatly increased settling rates were observed following precipitation of positive and negative polyelectrolytes on the surface of finely divided minerals in aqueous suspension. The ratios of polycationic to polyanionic electrolytes required to produce maximum sedimentation have been shown to correspond closely with the equivalence points obtained by light scattering studies of systems containing the positive and negative polyelectrolytes by themselves. DISPERSION of colloids has been of interest to surface chemists for many years. Flocculation studies have been employed to evaluate the limits of colloid stability. In water suspensions, colloids become unstable and flocculate when the 5 potential, the potential of the kinetic solvation sheath, falls to a value at which van der Waals forces may act to draw the particles together. This may happen through an adjustment of the pH of the suspension or by addition of a salt. Optimum conditions for rapid formation of large flocs are found in the region of minimum < potential. In addition to these well known considerations, colloids in water suspensions are known to be flocculated by certain large organic macromolecules. These polyelectrolytes in some cases minimize the 5 potential and in other instances increase the attractive forces by supplying sites for hydrogen bonding.&apos; Use of organic polyelectrolytes in flocculation of mineral colloids has increased rapidly in recent years. These materials are now recognized as indispensable aids to fluid-solid separations in many extractive metallurgical operations. They have been found to increase both the settling rate in thickeners and the filtration rate of filters. In the elucidation of the characteristics of these organic reagents as floc-culants in this laboratory, it was discovered that interaction of certain polyelectrolytes had a surprisingly good effect on flocculation of mineral colloids. Experimental Procedure: The anionic flocculants used in this study were Lytron 886 and 887, produced by Monsanto Chemical Co. Both reagents are copolymers of vinyl acetate and maleic anhydride. Lime is added to Lytron 886, whereas Lytron 887 is all organic. These reagents possess two carboxyl groups for each acetate group and are therefore anionic in character. The cationic reagents used were the Peter Cooper Co. 1-X and 2-X glues. The structures are not definitely known, but the re- agents are amines and are cationic in character. The glues were prepared in the chrome-alum form. Both types of reagents may be classified as polyelectrolytes in that they are high molecular weight polymers and ionize in water. All data presented are in terms of sedimentation rate, measured in 250-ml glass-stoppered graduated cylinders. With suitable precautions such measurements are fairly reproducible and provide a sensitive means for selecting important parameters such as PH, reagent concentration, and floc size and density. Agitation was standardized with five complete end over end cycles of the suspensions in the stoppered graduated cylinders.

Jan 1, 1957

By Irving Palmer

DURING the past 15 years in this country there have been few additions to the literature of lead smelting. After the consolidation of the principal smelting companies at the beginning of this period it became the policy of the larger company not to permit the publication of details in regard to many of its metallurgical processes. This led to similar action on the part of some of its competitors. The result, of course, was a decided decrease in the number of papers written upon the practical side of the subject. Even upon the theoretical side the contributions have been few. It would seem that the industry as a whole has suffered from this general unwillingness to exchange information. While it is true that a given company is entitled to the reward that may come from its own development of a new process, it is also true that a still greater reward might be the result of a free exchange of ideas with other plants. This principle has been recognized for a long time in other metallurgical industries, notably those engaged in the smelting of iron and the manufacture of steel. It is pleasing to note that the leading lead-smelting company has very recently decided to modify its policy of secrecy, and to permit the publication of papers covering some details of its metallurgical methods. The statement has been made that there has been but little progress in lead smelting during the period just referred to. This impression is due in part to the scarcity of papers written on the subject. There has been, it is true, some discussion of the new sintering processes, but with little reference to detail, and to the effect that blast roasting has had upon the industry as a whole. In spite of the prevailing belief, it may be said that lead smelting, in common with other metallurgical industries, has made steady and substantial progress. It is the purpose of the present paper to discuss briefly some features of the industry as it is now conducted, with special reference to the blast-furnace practice in the larger silver-lead smelting plants of the United States and Mexico.

Jan 7, 1914

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples. Gaudin,1,2 the first to apply a nuclear reaction in detecting beryllium minerals, developed a method that irradiates the sample with gamma rays, which react with beryllium nuclei to produce neutrons. The neutrons are then measured with standard equipment. The cross section for this reaction is about 1 millibarn. The cross section is a measure of the probability that a reaction will take place, for example, between a beryllium nucleus and an incident gamma ray or alpha particles.3-5 At 1-millibarn cross section for the reaction, satisfactory performance required a source strength of the order of 1 curie (3.7 x 10"&apos; disintegrations per sec, where each disintegration releases one or more gamma rays). The reactions will not take place if the gamma radiation is below a minimum energy, in this case 1.63 mev. The size of the source and the energy of the radiation made heavy shielding necessary for these experiments, both to reduce the background count of the neutron counter and to safeguard personnel. The original discovery of the neutron by Chad-wick in 1932 resulted from experiments with another nuclear reaction, induced by bombarding beryllium with alpha particles in which the products are carbon-12 and neutrons. The equation for this reaction is as follows:&apos; " ,Be" + ,He&apos;? 6C12 + 8,n&apos; [1] re-particle neutron In the above nuclear equation (Eq. 1), the sub- script number indicates the number of protons in the nucleus (the atomic number) and the superscript the total number of neutrons and protons (approximately the atomic mass). For the alpha-neutron reaction the cross section is about 250 milli-barns, or 250 times that of the gamma-neutron reaction used by Gaudin. The positively charged alpha particle is repelled by the positive charge of the beryllium nucleus; it must, therefore, have a certain minimum energy in order to approach close enough to the beryllium nucleus to react. For reaction with the beryllium nucleus, the lower limit of the alpha-particle energy is 3.7 mev. The alpha-neutron reaction, with polonium-210 as an alpha source, was selected for the present experiments. Alpha particles are emitted by polonium-210 at 5.30 mev, which is adequate for the reaction with beryllium. Furthermore, this isotope of polonium emits alpha particles with negligible associated gamma radiation, thus eliminating the necessity of shielding. The half-life of polonium-210 is 138 days. Inasmuch as alpha particles carry a possible charge and are large compared with most nuclear particles, their energy is rapidly dissipated in passing through matter. Their range in standard air is 3.66 cm,3 and they penetrate only a few tens of microns into a mineral sample. The short range in air can be minimized by preparation of a flat sample surface that can be brought very close to the alpha source during analysis. On the other hand, short range of alpha particles in air lessens the radiological health hazard and makes it possible to use this method without shielding. It must be emphasized, however, that the alpha emitters are potentially very dangerous if they enter the human body. Polonium must be handled with extreme caution. The literature has reported experiments on the yield of neutrons from reaction of alpha particles with beryllium nuclei. Feld" reports that in intimate mixtures of polonium and beryllium, 3 x 106 eutrons per sec are produced per curie of polonium. Elsewhere in the same reference it is stated that a sandwich-type source yields about one third as many neutrons as an intimate mixture. A table of neutron yields for full energy polonium alpha-particles on thick targets as reported by Anderson7 is the basis of Table I. From Table I it can be deduced that the elements most likely to interfere, i.e., those that also produce neutrons when bombarded by alpha particles, are boron and fluorine. These data also show that it will probably not be possible to determine very small quantities of beryllium in rocks because of the masking effects of the major elements, sodium, magnesium, and aluminum. The neutrons emitted in the alpha reaction are detected by another nuclear reaction. Either of the

Jan 1, 1960

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By Desmond Y. M. Lee

Computerized preventive maintenance has been a long sought goal in many industries. People have firmly believed that proper implementation of such a system can result in tremendous saving of money. However, the preventive part has always been left out without realizing it due to the inflexibility of coping with environmental changes. With this in mind, the Iron Ore Company of Canada has developed a computerized system which schedules maintenance jobs preventively.

Jan 1, 1977

By J. L. Fitch, B. G. Hurd

The presence of gypsum in samples subjected to standard core analysis introduces serious errors in the measurement of water saturation and porosity. The magnitude of these errors, depending upon the type of analysis procedure used, has been evaluated experimentally and theoretically. Water-saturated pore volumes determined by vacuum distillation or retort procedures may be too high by as much as 48 per cent of the volume of gypsum present. The maximum error in this value determined by Dean-Stark extraction with toluene is 36 per cent of the gypsum volume. If pore space is measured by a Boyle&apos;s law type porosimeter the maximum erorr due to gypsum is 38 per cent of the original gypsum volume present. The conscientious core analyst may eliminate the errors caused by gypsum by either of two methods. He may apply suitable corrections for the water of crystallization removed from gypsum, or take special precautions to prevent dehydration of gypsum during core cleaning and alzalysis procedures. These alternatives are discussed and methods for obtaining reliable core analysis data are proposed. Gypsum (CaSO4 . 2H2O) occurs as a common mineral in many of the world&apos;s sedimentary basins. In addition to its presence as primary bedded evaporitic deposits, it is often found as secondary replacement zones and pore-fillings in host rocks. That it may cause false indications in porosity, both on neutron logs and in standard core analysis, has been generally recognized. False porosity interpretations from neutron logs result because the chemically bound water in gypsum attenuates neutrons as effectively as free water. Errors in core analysis result when gypsum is dehydrated prior to or during the analysis. Vacuum retort procedures used by many laboratories to determine fluid saturation and porosity effect a complete removal of water of crystallization from gypsum. The crystal water, distilled and collected with free water from the sample, is counted as water-sat11rated pore space. Dehydration of gypsum results in a decrease in volume occupied by calcium sulfate and a corresponding increase in pore volume. Thus, if gypsum is dehydrated by sample cleaning and drying procedures, subsequent porosity measurements with gas expansion or compression instruments will be high. The qualitative effect of gypsum on porosity determinations by retort procedures was discussed in a recent article by Bynum and Koepl3. They concluded that since false porosity was interpreted as being water saturated, determinations of oil content were not affected. Others in the industry, however, have pointed out that porosity values are often used with values of water saturation determined independently, e.g., from electric resistivity logs in making reserve estimates. Values of water saturation calculated from the formation resistivity using the Archie equation, S4= are actually low if values of are high due to gypsum. In this case, false porosity values due to gypsum could cause serious errors in calculations of oil-in-place. This investigation was made to determine quantitatively the effect of gypsum on porosity values determined by different core analysis procedures. EXPERIMENTAL PROCEDURES Dehydration of Gypsum The extent and rate of removal of water of crystallization from gypsum under conditions encountered in core analysis procedures were studied. Taken for the experiments were three types of relatively pure, naturally occurring gypsum, viz. selenite, satin spar and massive gypsum. Although all samples probably contained trace chemical impurities, each type lost the theoretical amount of water upon complete dehydration. An automatic recording thermobalance, similar to one described by Mauer2, was used to obtain dehydration rate data for samples heated in dry air. Water

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By George W. Riter

Discussion of the paper of H. 0. Hofman and C. R. Hayward, presented at the New Haven Meeting, February, 1909, and printed in Bulletin No. 30, June, 1909, pp. 513 to 529. GEORGE W. RITER, Salt Lake City, Utah (communication to the Secretary*).-In their paper, Messrs. Hofman and Hayward deal with a branch of silver metallurgy that is on very uncertain ground, both as a commercial process and as a metallurgical science; moreover, its field is limited to few localities and to peculiar conditions. The literature on the subject is incomplete and full of conflicts. The paper under discussion clears u p no disputed points; on the contrary, because of hasty generalization, its tendency is towards further confusion. In Table I., the authors assume that each test-lot of 1,800 g. of ore contained exactly 5.499 g. of silver, that any variation in the quantity of silver recovered, however slight, should be ascribed to variation in the time of grinding. It is barely possible that the ore was mixed so uniformly as to justify this assumption; but those of us who know how difficult it is to get uniform samples of any ore in which silver mineral is present in rich particles will have a doubt on this point. The unlikelihood of getting absolutely uniform test-lots of ore also reflects on the data in Table II., on the effect of varying the amount of salt in a pan-charge. The authors say " The salt series was the last one that was investigated." This again raises a question as to whether the ore was split into test-lots at the time of sampling, or whether it was kept in bulk in such a way as to permit mechanical concentration of values before the end of the experiments. The conclusion following Table II.: " There is no reason, therefore, for going beyond six per cent. of salt," is hardly to the point. If we assume that salt is of benefit only when in solution, it follows that the relation between the quantity of salt

Mar 1, 1910

By A. U. Seybolt, R. E. Honnemon

THE purpose of this communication is to present activity data of nickel in the Ni-A1 binary system that was obtained for oxidation studies in this system. This data has been calculated from previous aluminum activity data at 1000°C1,2 by two types of Gibbs-Duhem integrations. These results should be of particular current interest to oxidation studies of aluminide coated nickel-base superalloys3 as well as other problems. The aluminum activity of Steiner and Komarek1 is plotted in Fig. 1 as a function of composition in Ni-A1 alloys at 1000°C. The dashed parts of the aluminum curves represent our approximate extrapolations from the directly measured regions. In the terminal solution regions (a and L phases) standard parabolic solution functions of the following form are assumed: where i is the component subscript, Ki is a constant at a fixed temperature, and xi is the atom fraction. The resultant nickel activity curve at 1000° C from the Gibbs-Duhem integration4 of the aluminum data is shown in Fig. 1. The solubility ranges of the phases present in the Ni-A1 binary at 1000°C are also denoted at the bottom of Fig. 1. Corresponding values of the nickel activity, aNi and yNi, are listed in Table I at useful compositional intervals. including phase boundary values. The aNi and yNi data listed in Table I are subject to the uncertainties present in the experimental aluminum activity data1 and to deviations from parabolic solution behavior in the terminal solutions. The errors introduced into aNi and yNi due to the parabolic solution assumption are expected to be relatively small (<20 pct of the values given) in all the phases except the liquid phase. Some deviation from parabolic solution behavior in the liquid phase is indicated

Jan 1, 1970

By Robert Kinzie

WHEN Mr. Cameron, the President of the Santa Cruz Portland Cement Co., returned from Europe in 1929, he brought first-hand infor-mation about a very versatile type of hydraulic cement. It was not a new cement, many articles having been written about it in foreign journals, but in this country the record of this type of cement had been either neglected or minimized. Using local materials, and applying the information brought back by Mr. Cameron together with many data in numerous publications, the Santa Cruz Portland Cement Co. developed the Santa Cruz high-silica cement. This cement is manufactured by grinding with portland cement clinker a properly calcined mixture of siliceous material and lime. It has all the utility of portland cement, together with an increased resistance to the destructive action of many aggressive solutions. To explain the necessity for the development of a cement having these characteristics, the history of hydraulic binding materials may be reviewed briefly. The materials used as binding media by primitive people were mud, lime, gypsum and bitumin. Due to its utility, ease of preparation, and its common occurrence, lime was the most widely used. Fat lime, when used by itself or with an inert sand, hardened only on the outside surface, where the carbonate was formed by absorption of carbon dioxide from the air, while, the interior of the mortar remained soft. It was quite early discovered that the incorporation of proper siliceous material with the lime increased its ability to harden, and for this purpose various natural siliceous powders were used, such as puzzo-lana in Italy, trass in what is now Germany, and santorin in Greece. These powders reacted with the lime forming a permanent cement and rendered unnecessary the access of carbon dioxide to the mortar.

Jan 1, 1934