Search Documents

By Robert Goodwin, Frank R. Milliken

In September 1937, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about I per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 60 per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig. I, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of which ranged from 62 to 74 per cent recovery. On the basis of these, a 200-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1943

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners' Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By W. Rostoker, R. P. Elliott, B. W. Levincer

Phase equilibria in the Ti-Cr-Mo system have been investigated for alloys containing 100 to 40 pct Ti in the temperature range 550° to 1300°C. Five experimental isothermal sections and a surface of incipient melting are presented in addition to a summary projection of the space. Seven vertical sections have been constructed from the isothermal sections. A STUDY of the system Ti-Cr-Mo was undertaken as part of a program sponsored by Watertown Arsenal toward the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range contained by the titanium corner and the line of 64 pct Ti (all compositions are by weight) and the temperature range 550" to 1100°C. A surface of incipient melting was constructed from measurements on a large number of alloys. The system Ti-Cr has been established.&apos;-? The phase diagram is characterized by a wide miscibility field of the solid solution at elevated temperatures and a eutectoid reaction of the type: (15 pct Cr) + TiCr, (685C). The a solid solution has a very limited capacity for solution of chromium (< 0.5 pct Cr). The intermediate phase TiCr2 has at best a very narrow composition range. It has been shown that two allotropic modifications of this phase exist. However, this behavior does not appear to be perceptibly reflected in the form of phase boundaries of the type + TiCr,. In the system Ti-Mo,9-10 the phase is stabilized to successively lower temperatures with increasing molybdenum content. There are no known intermediate phases. The a solid solution is limited to less than 0.5 pct Mo. Because of the very extensive range of the phase, the ternary system was ideally suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." A parametric surface was constructed to provide the necessary basis for the application of this method. Preparation and Treatment of Alloys More than 60 alloy compositions were prepared for the study of this system. Alloy buttons of 10 grams were arc-melted in a nonconsumable electrode furnace using inert atmosphere protection and a water-cooled copper crucible. The construction and operation of this type of melting unit have been adequately described elsewhere.&apos;&apos; To insure complete solution of alloy additions, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" over the ingots. Iodide titanium (99.97 pct Ti) was used as the alloy base. An especially high quality chromium (99.9 pct Cr) was obtained from the National Research Corp. Molybdenum sheet (0.005 in.) of 99.9 pct purity was used.

Jan 1, 1954

By William Carton, Cyril U. Cooledge

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By Cyril U. Cooledge, William Carton

BecauSe the rich La Colorada orebody of the Cananea Consolidated Copper Co. does not outcrop at surface, after its discovery (by churn drill) and before mining was begun, a large amount of development work was done to learn the shape and extent of the ore and to provide for economic and effective mining. As these openings progressed, the actual shape of the orebody became known and with this knowledge came the realization that mining this rich and unusual deposit without loss of ore or danger to workmen presented several difficult problems. This paper will describe one of these problems; namely, the handling of an inverted cone-shaped core of barren rock, on the periphery of and below which the ore occurred. It mas clear that as the ore was mined out from around and under this inverted cone of rock, weighing about 3,000,000 tons, it would hang over the workings, held suspended only by its own tensile strength and threatening to crash into the stapes below with disastrous results to men and mine. The method of mining developed during the years 1928,1929 and 1930 anticipated and provided for the eventual collapse of this core of rock. In November 1936 the core settled down gradually on the edges of the stopes, descending a total of about 50 ft. vertically. The men in the stopes had ample warning and no lives were endangered. There were no air blasts in the mine. The core broke loose from its top support at the 500-ft. level along old fracture planes and evidently is crushed to the ninth level. Movement was of short duration; the following shift went to work in the stopes as usual. No ore was lost. Geological Structure The shape of the orebody is illustrated in Fig. 1. The geology of the Colorada orebody has been described by V. D. Perry1 and by W. G.

Jan 1, 1940

By A. Coskun, J. F. Elliott

The activity of aluminum in liquid Al-Fe alloys .has been measured by an improved version of the transportation method in which the metallic vapor has been collected by its solution in a metallic condenser. The results can be represented by the equation: log yAl = -3.0(1 - xAl2) (0.6 < XAl < 1.0) This equation applies at 1315°C. MORRIS and zellarsl adapted the transportation method for measuring the vapor pressure of a com- ponent of an alloy at high temperature. We have modified their technique further2 for use with metals that are strong oxide formers. In the present case the method has been applied to the Al- Fe system to obtain the activity of aluminum in the liquid region at 1315°C. Dried ultrahigh-purity hydrogen (Matheson) is the carrier gas. The operations, Fig. 1, of deoxidizing the gas, equilibrating the gas with the sample at 1315";, and then collecting the aluminum vapor are all accomplished within a single, continuous alumina tube to avoid contamination of the system by leaks. De-oxidation to a very low level of PO2 (<10-25 atm) is Obtained by passing the hydrogen through a tightly packed bed of aluminum powder. The temperature of this bed increases to approximately 550°C in the direction of the gas flow. The boat containing three pellets of the alloy is supported on the end of a

Jan 1, 1969

By W. R. Hamilton

The knowledge of the existence of petroleum in Southern California dates back to the days of the missions. The presence of asphaltum and semisolid bitumen was reported at Santa Barbara in 1792, but no serious attempt was made to develop oil until Professor Silliman&apos;s optimistic report in 1865 started California&apos;s first oil boom. Wells were drilled in many counties of the State, but the equipment was unsuitable and the drilling difficult and no production was obtained except in Ventura County. Even there the production was of little importance commercially, and not until the early &apos;80s did it become sufficient to again attract attention. In 1888 the production for the State had reached a total of about 700,000 bbl. per year, practically all light oil produced in Ventura County, Pico Canyon, Los Angeles County and in the Puente Hills. The production of petroleum attained the dignity of an industry in 1895 when the Los Angeles City and Coalinga fields were discovered. The subsequent development has been remarkable, and in 20 years the production has increased from 1,000,000 to 100,000,000 bb1. per year. The refining industry has kept pace with the production of oil. The Pacific Coast Oil Co., the predecessor of the Standard Oil Co. of California, was the virtual pioneer refining company of the State, having built a refinery at Alameda about 1880. When purchased by the Standard, about 1902, it was dismantled and the refinery at Point Richmond was built. The Richmond refinery is now one of the largest in the world, having a capacity in excess of 60,000 bbl. per day. A small refinery was built by the Union Oil Co. at Santa Paula in the early days of the industry and later many asphalt refineries were in operation in Southern California. The Pacific Coast Oil Co. was then, as has been its successor, the Standard Oil Co. of California, the principal refiner and marketer of light products, the most valuable of which was kerosene. Before the opening of the twentieth century, gasoline of excellent quality was produced, though it was always a drug on the market and was produced for the simple reason that its presence rendered the flash and fire tests of the kerosene too low. The user of kerosene at the present

Jan 1, 1917

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.&apos; : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*&apos;" Exotic recovery processes have been considered primarily for &apos; perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period Mar. 10 to Apr. 10, 1915: Oscar Lachmund, Greenwood, B. C. Harvey B. Small, Mangaugue, Colombia. S. W. Ough, Pachuca, Mexico. M. F. Sayre, Schenectady, N. Y. B. W. Vallat, Detroit, Mich. James W. Hambleton, Parral, Mexico. Charles Mentzel, New York, N. I . Philip L. Gill, Woodmere, L. I., N. 1. M. K. Rodgers, San Francisco, Cal. John T. Fuller is President of the F. Shepherd Mining Co., operating at Rush Mountain, Ark.

Jan 5, 1915

By W. R. Hibbard

THE classical work on the electrical conductivity of alloys was carried out by Matthiessen and his coworkers1 in the early 1860&apos;s. He attempted to correlate the electrical conductivity of alloys with their constitution diagrams, but the information regarding the latter was too meager for success. Guertler2 reworked Matthiessen&apos;s and other conductivity data in 1906 on the basis of volume composition (an application of Le Chatelier&apos;s principle with implications as to temperature and pressure effects), and obtained the following relationships between specific conductivity and phase diagrams (plotted as volume compositions) : 1—For two-phase regions, electrical conductivity can be considered as a linear function of volume composition, following the law of mixtures. 2—For solid solutions, except intermetallic compounds, the electrical conductivity is lowered by solute additions first very extensively and later more gradually, such that a minimum occurs in systems with complete solid solubility. This minimum forms from a catenary type of curve. Intermetallic compound formation with variable compound composition results in a maximum conductivity at the stoi-chiometric composition. Landauer" has recently considered the resistivity of binary metallic two-phase mixtures on the basis of randomly distributed spherical-shaped regions of two phases having different conductivities. His derivation predicts deviations from the law of mixtures which fit measurements on alloys of 6 systems out of 13 considered. Volency (Ionic Charge) Perhaps the first comprehensive discussion of the electrical resistivity of dilute solid-solution alloys was presented by Norbury&apos; in 1921. He collected sufficient data to show that the change in resistance caused by 1 atomic pct binary solute additions is periodic* in character. The difference between the period and/or the group of the solvent and solute elements could be correlated with the increase in resistance. Linde5-7 determined the electrical resistivity (p) of solid solutions containing up to about 4 atomic pct of various solutes in copper, silver, and gold at several temperatures. He reported that the extrapolated"" increase in resistance per atomic percent addition is a function of the square of the difference in group number of the solute and solvent as follows: ?p= a + K(N-Ng)2 where a and K are empirical constants and N and Ng are group numbers of the constituents. This empirical relation was subsequently rationalized theoretically by Mott,8 who showed that the scattering of conduction electrons is proportional to the square of the scattering charge at lattice sites. Thus, the change in resistance of dilute alloys is propor-t,ional to the square of the difference between the ionic charge (or valence) of the solvent and solute when other factors are neglected. Mott&apos;s difficulty in evaluating the volume of the lattice near each atom site where the valency electrons tend to segre-gate: limited his calculations to proportionality relations. Recently, Robinson and Dorn" reconfirmed this relationship for dilute aluminum solid-solution alloys at 20°C, using an effective charge of 2.5 for aluminum. In terms of valence, Linde&apos;s equation becomes ?P= {K2 + K1 (Z8 -Za)2} A where K1 and K2 are coefficients, A is atomic percent solute, Z, is valence of solvent, and Zß, is valence of solute. Plots of these data for copper, silver, gold, and aluminum alloys are shown in Fig. 1. The values of K1 and K2 are constant for a given chemical period (P), but vary from period to period. The value of K, increases irregularly with increasing difference between the period of the solvent and solute element (AP), being zero when AP is zero. The value of K, appears to have no obvious periodic relationship. All factors other than valence that affect resistivity are gathered in these coefficients. Because of the nature of the coefficients, Eq. 1 is of limited use in estimating the effects of solute additions on resistivity unless a large amount of experimental data are already available on the systems involved. It is the purpose of the first part of this report to investigate the factors that may be included in the coefficients of Linde&apos;s equation. On this basis, it is hoped that the relative effects of solute additions on resistivity can be better estimated from basic data, leading to a more convenient alloy design procedure. It is well 10,11 that phenomena that decrease the perfection of the periodic field in an atomic lattice, such as the introduction of a solute atom or strain due to deformation, will also increase the electrical resistivity. Thus, in an effort to relate changes in electrical resistivity to alloy composition, it appears appropriate to consider the atomic characteristics related to solution and strain hardening

Jan 1, 1955

CURRENT MATTERS Page Page New York Meeting v Federal Control of Minerals xxxii Meeting of Board of Directors.. ix Naval Consulting Board...&apos; xxxix Reports for Year, 1917: Perkin Medal xl Secretary ix Communication from Albert Treasurer xvii Sauveur xl Committee on Membership... xx Affiliated Student Societies xli Committee on Increase of Membership in Military Service... xli Membership xx Personal xlvii Committee on Publications... xxii Positions Vacant 1 Committee on Library xxiii Engineers Available li Local Section News: Forthcoming Meetings lii Boston xxiv Library liii. Columbia xxv Membership lvii San Francisco xxx Institute Committees lxx Qualifications for Membership.. xxxi Officers and Directors lxxviii.

Jan 2, 1918

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days&apos; production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By FRANK R. VAN

I. INTRODUCTION. IN the summer of 1908, R. B. Cochran, Superintendent of the Compania Metalurgica Mexicana at Sierra Mojada, Mexico, presented to the Department of Geology and Mineralogy at Case School of Applied Science an interesting series of silver-, copper-, and lead-ores from the Veta Rica mine. These ores contained several interesting minerals which were associated in a somewhat peculiar manner, so that I was impelled to make a closer study of their occurrence. The investigation has brought out several new facts concerning the geology of the district and the geological occurrence of the ores, and therefore has seemed worthy of record. Two papers have been published previously about the region, one by Chism1 in 1887, and the other by Malcolmson2 in 1902. These articles, however, treat of the district more from the stand-point of the metallurgist and mining engineer, and not much attention is devoted to its mineralogy and economic geology. II. GEOGRAPHICAL LOCATION OF THE DISTRICT. The Sierra Mojada is situated in the extreme western part of the State of Coahuila, near the Chihuahua boundary. It is reached best via the Mexican Central railroad from El Paso, Tex., to Escalon, Chihuahua, a distance of 494 miles. From this point, a branch line, the Mexican Northern railroad, runs 78 miles in a NE. direction to the mines, which are its northern terminus. The railroad was built about 1890, practically on account of the Sierra Mojada mining-district. 1 Sierra Mojada, Mexico, by Richard E. Chism, Trans., xv., 542 (1886-87). 2 The Sierra Mojada, Coahuila, Mexico, and Its Ore-Deposits, by James W. Malcomson, Tram., xxxii., 100 (1901).

Aug 1, 1912

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By W. H. Emmons

Although gold is one of the rarer metals, it is widely distributed; it is found on all of the continents and in each of the grand metallogenic provinces of the earth. It is prominent particularly in the shield areas of the earth; these areas have produced a large part of the world&apos;s lode gold and in most of them gold lodes are more important than the lodes of other metals. The Scandinavian shield is the only one that has not produced much gold. Nearly all of the world&apos;s gold has been derived from lodes and from sands and gravels where gold placers formed by the destruction of lodes. The gold derived from magmatic segregations, from pegmatites and from contact metamorphic deposits is quite subordinate to that derived from auriferous lodes. The lodes include all veins and related deposits that are formed by hot waters that move along fissures or other openings and that deposit vein &apos;matter :in the fissures and by replacement of the country rocks along the fissures. All of the shield areas of the earth are characterized by large areas of granitic rocks including granitic gneisses, granodiorites and other acid intrusives which here are included in the general term "granite." The granites are intruded into schists, ancient lavas and other rocks which here are designated as the "invaded" rocks. The granites are parts of what once were great batholiths: that is, they are the remaining portions of great deep-seated bodies that slope outward, have very irregular roofs and so far as known have no floors but extend downward to great though unknown depths. Some of them are scores or hundreds of miles across and contain islands or "roof pendants" of the invaded rocks at places where the roofs of the batholiths were low—that is, where erosion has not yet completely unroofed the batholiths. It is in these islands of older rocks and in the narrow marginal belts and cupolas of the batholiths that practically all of the gold lode deposits of the shields are found. Valuable lodes are lacking generally in the granites themselves except in grahite within a mile or less from .the contacts with rocks of the islands (Fig. 1). It is probable that the great areas of granites and gneisses that surround the islands are not all of the same age, and that at places unmapped granite intrudes gneiss or older

Jan 1, 1932

By Albert R. Ledoux

Discussion of the Paper of Albert R. Ledoux, read at the Atlantic City Meeting, February, 1904. ARTHUR JARMAN, Sydney, New South Wales, Australia&apos; (communication to the Secretary*): Some remarks upon. Dr. Ledoux&apos;s interesting paper from one who has not visited America may, I hope, be of interest to members. It appears to me that there is considerable difference between the training of the American and of the British mining engineer. Not that the subjects are different, but rather in the way in which they are handled, the illustrations being, as far as possible, mining in character. Colloquial instruction is unknown in English curricula, but could be introduced with advantage. Students here assure me that an hour of conversation is of tar more use to them than an hour of the best lecturing. In England a school-year of 6 or 7 months would be considered very short indeed; but Americans do not consider it so, for the reason that the rest of the year is mostly spent in acquiring practical acquaintance with their subjects in works or in the field, and the shorter courses, when coupled with this large amount of outside expe¬rience, produce an essentially practical-minded engineer, who is also more of a business man; whereas the English system, though excellent from a scholastic point of view, produces the theoretical rather than the practical man. British schools are waking up, however, and the practical aspect of the engineer&apos;s training is receiving greater consideration. Once launched upon his career, the American engineer is immediately called upon to exercise his self-reliance and ingenuity, if he is to retain the confidence of his employers; but what can we say of English directors? In how many cases is the engineer allowed to guide the destinies of his company? Witness several recent cases of gross waste of money upon unsuitable plants, and the perpetuation of prehistoric methods of

Mar 1, 1905

By T. E. Schwarz

The publication of the report by Mr. F. L. Ransome1 was welcomed by many engineers who had mined in the heart of the San Juan country, braved its long and snowy winters, climbed its lofty peaks, run the gauntlet of its snow-slides, and studied its problems of geology, while making dividends for their English or American clients. This report helps one to understand why the bonanzas occurred, and why the inevitable " borrasca " presents itself where least expected. The Red Mountain district of Ouray county, a very productive section from 1884 to 1893, occupies considerable space in the report mentioned. The character of the ore-occurrence.

Jan 1, 1906

ABOUT 2 lb. of alumina (aluminum oxide) of high purity is required to produce a pound of metallic aluminum. Projected production of metallic aluminum in the United States is now seven to ten times the peacetime rate a few years ago. In the past, all the alumina for aluminum production in the United States has been obtained from bauxite. Part of the bauxite was mined in the United States--chiefly in Arkansas-and part was imported from Surinam. All of it was chemically treated in the United States to separate the greater part of the aluminum oxide from the bauxite, alkaline solutions being used, in a method known as the Bayer process. The ingredients of the bauxite other than alumina, such as the compounds of iron titanium, and silicon, constitute the tailings from the Bayer-process operation. This product contains sufficient iron to give it a red color and hence it is called "red mud." Lime and soda used in the processing, are also present. Varying amounts of alumina remain in the red mud, depending upon the characteristics of the bauxite, the effectiveness of the treatment, and in particular upon the amount of silica originally present in the bauxite. High-silica bauxites result in high alumina loss in the red mud.

Jan 1, 1942