Search Documents

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.' Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By R. E. Hobart

The development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines, led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was 2 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 1, 1918

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"' and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

By Wayne P. Myers

Electricity, as normally thought of by a layman's definition, is a manmade force that has no color, no odor, is not visible, cannot be heard, yet man can control it and make it perform his work for him. A person dare not cheat on it, for it then will master him. It has laws, rules, and regulations that must be strictly adhered to if it is to perform in the safest, most reliable, and economical manner. In the early days of coal mining the power source was man himself. Later man employed steam and compressed air to reduce his muscle power requirements needed in the extraction of coal. By the turn of the 20th century, electricity had become the most common source of power for the coal industry. Steam and compressed air are still found in use in isolated cases today for specific applications; however, they are rapidly being replaced by electricity. Electrical laws and regulations are quite extensive and somewhat complex for the proper generation and use of electricity. Man-made laws, rules, and regulations for the care and handling of electricity, designed for man's safety, are rigidly enforced by the U.S. Bureau of Mines, as well as the various state departments of mines. BACKGROUND Until recent years most underground coal mines used direct current exclusively for all movable and for some stationary equipment. Exceptions were for permanent pumps, tipple, fan, and outside buildings where alternating current was normally employed. However, over 60 years ago there were mines with dual systems. Alternating current was used for cutting machines, drills, and pumps, direct current for locomotives. There were no other machines as these were hand-loading mines. Later, during early mechanization in the 1920s, alternating current was also applied to loading machines at some mines. Use of dual electric systems then declined until fairly recently when

Jan 1, 1973

By Thomas T., Read

IT will be recalled that the first professor of metallurgy in the United States, appointed in 1855, never really gave any instruction in metallurgy and gradually turned into a professor of mineralogy. Metallurgy was included with. mining in the early curricula, two students who took the B.S. in mining engineering from the Polytechnic College of Pennsylvania in 1862 wrote their graduation theses on the metallurgy of copper and zinc, respectively. Even after Columbia School of Mines established, in 1868, a separate curriculum leading to the Ph.B. degree in metallurgy, very few students elected it,* preferring to take the mining degree, since they received in its curriculum nearly all the metallurgical instruction they would have in the metallurgical curriculum. For many years a large proportion of the men who attained prominence in metallurgical enterprises had taken mining rather than metallurgical degrees. METALLURGY Clifton Sorby's study of thin sections of rocks under the micro¬scope, beginning in 1850, and its subsequent development by Zirkel and others, had made microscopic petrography a recog¬nized department of geological research as early as 1873. . It was inevitable that the idea of studying polished metal surfaces-¬under the microscope by reflected instead of transmitted light would occur to investigators. Sorby himself did it in 1864, and Adolph Martens and Floris Osmond may -be especially named among the many European workers who, by the late eighties, had so developed the, necessary techniques that they were able to photograph polished metal surfaces at magnifications as high

Jan 1, 1941

By John Garcia

THE presence of carbon de terre along the banks of the Illinois river was noted by the members of the Joliet and Marquette expeditions in 1673, and that may be referred to as the birthday of coal in the Middle West. The march of progress in the majority of indus-tries radiating from Chicago-one of the phenomena of history-is due in no small measure to this same carbon de terre and to the development and exploita-tion of the vast coal resources, which nature in a generous mood spread so lavishly over almost the en-tire state. The geological records indicate that coal-bearing rocks underlie three-quarters of Illinois, in-cluding 85 of the 102 counties and the entire area is estimated at from 36,000 to 42,000 square miles. Not all of the coal in this great area may be mined under the conditions existing today; producers are now taking the "cream" since industry demands the best quality and the lowest cost, thereby forcing competition among operators, which, in turn, com-pels the development of mines in those areas where the coal may be most readily .won, leaving the coal that is more difficult and expensive to mine to pos-terity. This is not such a bad arrangement, since the engineers of succeeding generations will enjoy the advantage of the experience of their ancestors, where-by they should profit and know how to mine a 2-ft. seam with as much economy and dispatch as we today work coal of thrice that thickness. During the period between 1830 and 1850, Illinois coal-mining progressed from the art of scratching along the outcrop to the development of small mines, mostly slopes, drifts and shallow shafts, but the real progress in the industry was coincident with the con-struction of railroads.

Jan 2, 1927

By Charles Baker

THE district of Catorce, San Luis Potosi, ranks among the first half-dozen silver-producing camps f Mexico. Mining has been more or less continuous there for 150 years. The large producing mines, Mapum, Mazapil, Palomas, Musquiz, Minas Virjas, now for the most part idle or abandoned, are grouped around the head of two valleys: one, which drains to the west, falls 2000 ft. (609.6 m.) in 4 1/2 mi. (7.2 km.) between the main Catorce and the western foot of the range and is characterized by steep canon walls; the other, east of the main town of Catorce from which it is separated by a high divide, heads in a number of steep tributaries above the basin in which lies the town of Potrero and flows nearly north for 10 mi. (16 km.) to the northern base of the range; below Potrero, it has for the most part gently sloping valley walls and a broad valley floor. The Sierra Catorce is the highest range of the region, the summits reaching altitudes of over 11,000 ft. With the exception of a few cliffs of the erosion escarpment of the lower limestone and the canon walls below the main town of Catorce, which is the highest town in Mexico, the gently rounded slopes are characteristic of a maturely eroded mountain range composed of folded sedimentary rocks. As is usual in desert regions, the heavy-bedded limestones are the most resistant to erosive forces. Folded into anticlines, they form the mountain ranges; and the intermontane valleys and basins, originally carved out of less resistant shales, clays, marls and sandstones, are covered by debris forming a mantle with surface gradually rising upwards toward the hills. In time, the debris buries, in deposits formed from their own ruins, all but the highest summits of the original mountains; some f this region has already nearly reached this stage. Most of the debris is firmly cemented by calcium carbonate (caliche). Solution f the limestone by meteoric waters afforded the supply of lime carbonate, which has been redeposited upon evaporation of the waters as a cement binding the boulders, pebbles, and finer detritus.

Jan 9, 1921

By F. M. Lewis, J. F. Meyers

This second progress report of grinding presents comments regarding ball consumption and data pertaining to the hydroscillator, which is closed circuited with the tricone mill. A study and postulate of how balls function is presented. The paper summarizes cost reduction obtained by the method of "grinding for the tail race" rather than for "mesh tons." AT the Regional meeting in Columbus, Ohio, in September 1949, the authors presented a progress report of the first year's operation with a Hardinge tricone mill in closed circuit with a Dorr hydroscillator. The present report covers our findings on this grinding circuit to January, 1950. In order to clarify our position, the authors wish to state that no invention or discovery is claimed. The Tennessee grinding circuit is simply an engineered arrangement of known equipment arranged to incorporate all of the recognized efficiency factors of comminution as they are known today. As we concluded our first report, it was not clear how effective the Tennessee mode of operation would be on harder ores. The only information we had at that time was that the Bond grindability test at 48-mesh gave 6.04 g of undersize per revolution. A later test on the same sample at 100-mesh reduced this to 2.04 g, which is definitely in the harder ore class, and which makes the reported 8.80 kw-hr per ton of —200-mesh produced a very creditable figure. Hydroscillator Operation The machine as now developed has proved dependable and easy to operate. It starts easily under full load and responds quickly to operating adjustments. The hydraulic holes in the oscillating plate do not plug when shut down under full load. Absolutely clean hydraulic water is essential. An Elliott water screen or similar device should be an essential part of the machine to keep all scale and trash of all kinds from the hydraulic compartment. The shift operators have expressed approval of the machine. In table I we show a typical screen analysis of the hydroscillator rake sand as compared to conventional classifier rake sand on our ore. We have previously reported that of the 28.7 pct reduction in power, the hydroscillator contributed 6 pct, on a —200-mesh basis. This is a conservative figure. Some of our test runs indicated that the saving was as high as 10 pct. Laboratory studies by the Dorr Co. engineers indicate that still greater efficiency is possible. Nevertheless, the 10-ft plate is overflowing 2100 tons per day at 3 to 4 pct + 65-mesh, which is a very creditable performance by

Jan 1, 1951

By J. Parker

As a practicing mining engineer, I face many rock mechanics' problems daily and would like to mention one or two examples to illustrate the current gap between laboratory investigations and actual field problems. I would like to endorse Dr. Obert's suggestion that more field measurements and observations should be undertaken. There is an ever-increasing body of data beginning with Hast's results in Sweden,l then measurements at Elliot Lake, Canada, and so on, including our own measurements at White Pine, which clearly indicate that the horizontal stresses underground. are often at least as large as the vertical stresses. Visual observation of the deformation of roof and pillars (including failure due to horizontal compres- sion) also demonstrates that the horizontal stresses are often most important: Yet almost every laboratory investigation begins with the assumption that the only stresses acting are vertical. Roof spans in layered formations. for example, are calculated on the assumption that the rock behaves as a gravity loaded beam. This is all too often unrealistic.

Jan 1, 1967

By S. E. Bretherton

(San Francisco Meeting, September, 1915) DURING the year 1878-79, Anton Eilers, who was then interested in the lead smelting and refining business near Salt Lake City, Utah, made a somewhat radical departure from the regular practice at that time, which was to use but little lime in the slag, with a high percentage of iron. Lime was not only a cheaper flux than iron, but it enabled the metallurgist to make a more siliceous slag, an economical advantage in smelting where the smelting companies had to purchase either iron or lime to neutralize the excess silica, and penalize the ore shippers accordingly. The larger amount of both lime and silica in the slag also made it of lighter specific gravity, and a better separation of the metals and mattes was secured. This change in the formation of slags for lead smelting was brought about by Anton Eilers, prior to the Leadville mining excitement of 1879. We must also give Mr. Eilers credit for the general introduction of the hollow water-cooled cast-iron jacket for the blast furnace. Again referring to the use of more lime and less iron in the formation of slags,. there is no doubt but that it prevents the formation of a great many so-called "sows" in the lead crucible, such as were made in the early history of lead smelting in the Rocky Mountains; these sows consisted of lead, iron, arsenic, sulphur, copper, and other metals, including gold and silver, mixed with unconsumed fuel, and often, after vain attempts to cut them up or melt them to a suitable size for handling, were buried in the slag clumps to get them out of-sight. Another advantage derived from the adoption of high-lime slags. when smelting ore containing arsenic is the production of less speiss (a by-product heavier than matte, resulting from careless operation of the furnace, the lead being driven out of the crucible and sows built up). This speiss, while usually not as rich in precious metals as matte made at the same time, is too valuable to be thrown away; but it is difficult to treat, and it was thrown away or piled on the slag clumps in the pioneer clays of lead smelting in this country.

Jan 8, 1915

The Western World's gold reserves now exceed 23,000 mt (750 million oz), 65% of which exist in South Africa. Although several major mines are reducing production or closing because of depletion of reserves, new mines or expansions of existing mines are coming on-stream which will maintain an annual production of 684 mt (22 million oz) of gold well into the 1990s. These new operations by the South African mining industry represent the largest expansion since the opening of the Witwatersrand gold fields in 1886. Included in three new mines being opened is that of Anglo American Corporation's Elandsrand plant, their fir& new gold venture in South Africa in seventeen years. Current average grade of South African mines is 8.2 g Au per mt (0.24 oz per st); and while the cost of the Elandsrand 135,000 mt (149,000 st) operation, including mine development, was about $314 million, it is estimated that the cost of a comparable operation started today and completed in the mid-1980s would be of the order of $480 million. New mines to exploit low-grade ore bodies are, therefore, likely to be few in number, and further expansion will undoubtedly be in the form of extensions to existkg operations where cash flow can be used to finance development. The authors' first monograph, "Gold and Silver Cyanidation Plant Practice," devoted a section to South African cyanide plant operation; and it is believed that this new volume would not be complete without a description of Elandsrand, South Africa's newest gold plant. The Elandsrand mine is adjacent to Anglo American's Western Deep Levels on the Far West Rand. The decision to go ahead with the development was taken in mid-1974 from the results of exploration drilling carried out over a period of .lo years. Results of 17 bore holes and 68 intersections of the Ventersdorp Contact Reef had indicated a gold-.bearing reef less than one meter thick at a depth of 1,800 to 3,000 meters (5,900 to 9,840 ft). Preliminary studies indicated a mine of 900 km (560 miles) of underground workings would yield 725,000 kg (23. 3 million oz) of gold from 60 million mt (66 million st) of ore to be milled over a period of 34 years. Eventually, when the mine is in full production, the total hoisting capacity will be 300,000 mt per month (331,000 st) for a milling capacity of 225,000 mt per month (248,000 st). The Elandsrand surface facilities have been built on a low range of 0 hills to take maximum advantage of the 10 slope in transporting ore

Jan 1, 1981

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer's primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By John M. Kelly

New Mexico produced 38,882,342 bbl. of oil in 1943, and regained seventh place among the oil-producing states. This production was an increase of 6,968,526 bbl., or 21.8 per cent, over the figure for 1942. The maximum per-well allowable on Jan. I, 1943, was 38 bbl. daily and at the end of the year this figure had been increased to 48 bbl. Allocations as set by the New Mexico Oil Conservation Commission closely followed recommendations by the Petroleum Administrator for War and the average daily pipe-line runs were 106,476 bbl., being within 2.2 per cent of these allocations. Production for Lea County was 33,043,925 bbl.; Eddy County, 5,405,-967 bbl.; northwestern New Mexico, 432,070 bbl., and Chaves County, 380 barrels. Drilling activity for New Mexico in 1943 was only 75 per cent of that in 1942, with 255 completions. Of these completions 180 were oil wells, 10 gas wells and 65 dry holes. The ratio of dry holes to producers, more than I to 3, was the greatest in recent years. Of these dry holes, 46 were drilled within the boundaries of proven . areas while 19 were wildcats. Wildcat drilling during 1943 was responsible for the discovery of four new oil fields and one new gas field, as well as three extensions to existing proration areas. At the close of the year the New Mexico Oil Conservation Commission had designated 64 areas as proven for oil and/or gas. The Monument area was again New Mexico's largest producing oil field, with an annual production of 7,228,855 bbl. Next was Eunice, with 6,461,044 bbl., followed by Vacuum with 4,946,110 bbl. IIobbs, ranking fourth, with 3,799,114 bbl., was the leader in total recovery with an accumulated production of 104,180,53I bbl., or more than 10,000 bbl. per acre to date. Drilling activity in Lea County accounted for completion of 67 oil wells, 2 gas wells and 24 dry holes. One of these oil wells was the discovery well of a new area and three extended proven areas. The most active drilling campaign in the county was again in the Maljamar area, where 18 oil wells were completed. The Maljamar Cooperative Repressuring Agreement affected 141 producing wells, and operations were a decided success, more than 85 per cent of the gas produced being returned to formation. The new oil field for Lea County was designated as the San Simon area although boundaries have not been established to date. Discovery well for this area was the Skelly Oil Company's State U. No. I, in theNE. NE. K of sec. 5, T.22 S.,R.ssE. This well was drilled to a total depth of 4183 ft. and plugged back to 4138 ft. after encountering bottom-hole water. Initial production was 124 bbl. per day on the pump. This oil is 37.4' gravity and has a sulphur content of I per cent. Productian is from Yates sand of Permian age. The Lynn area of southern Lea cbunty was extended 145 miles to the northwest

Jan 1, 1944

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1984

By T. L. Joseph

S. T. Killian (Johnstown, Pa.)—This is one of the finest papers I have read. Tying in stoichiometric calculations with furnace performance and practice is a step which had to be taken sooner or later. The noteworthy difference between Dr. Joseph's type of calculations and regular blast furnace calculations is that the Ib mol system is used as a basis. With the Ib mol system, weights, volumes, and chemical reactions can all be expressed in the same equation. In the paper, wind, ore, flux, and fuel are all expressed as lb or lb mols. Probably Dr. Joseph does not realize it, but the vague word coke appears only twice in the entire paper. Lb of C and Ib mols of C are followed through reactions but the word coke appears only as 1560 lb coke per ton of pig and 1700 lb of coke per ton of iron. Obviously in order to understand furnace reactions, the coke should be expressed as lb or lb mols of C. Furnaces can also be compared more easily. In some respects the paper is too thorough and too complete. The effects of the metalloids reduced into the iron upon the top gases represents a difference of less than 3 pct of the CO formed in the bosh. Due to the completeness of the calculations in relation to the CO/CO2 ratio, this was included and was necessary. However, the exclusion might have enabled more furnace men to follow the lb mol system of calculations through the blast furnace to a better degree. By considering only irons of similar analysis, this part of the calculations might have been omitted. However, if this had been done, total rewriting of the paper later would have been necessary in order to make the work complete as it is now. It also would not have been nearly as authoritative. In the paper, there appears the reaction: H2O + CO ? CO2 + H2 [I] Dr. Joseph states that he did not take this reaction into consideration in any calculations pertaining directly to the paper. The piobable reason- for this is that although it contains all the main reacting top gases except N2, it is rather inflexible since it is monomolecular in relation to each of the reacting gases and does not tie in with the gasification of C. Actually the reactions: H2O + C ? CO + H2 [2] 2H2O + C ? CO2 + H2 [31 and the solution loss reaction: CO2 + c ? 2c0 [41 tend to assume an equilibrium through the reaction: H2O + CO ? CO2 + H2 [I] which should be considered a balancing or equilibrium reaction. Reactions 2, 3 and 4 permit furnace conditions to balance with the CO/CO2 ratio and H2 formation. They tie in with the solution loss. Reaction 1 unites them chemically. Probably the best calculation to make at this time would be to try to find the relative importance of the CO2 from the flux and the H2 in the dilution on an actual furnace gas analysis. For this purpose the Dob-scha-Carnegie-Illinois paper—"Effect of Sized and Sintered Mesabi Iron Ores On Blast Furnace Performance" is chosen. This paper was presented before the blast furnace section of the AIME in 1948. This represents the best large scale furnace operation available to me. Unfortunately the changes were brought about by beneficiation of the burden and not by changes on one burden. In choosing the basis for the calculation in relation to the furnace, 100 mols of dry top sgas is chosen. This leaves something to be desired inasmuch as the nitrogen basis is changing but I believe it will be better understood than any other type and it is the easiest to use.

Jan 1, 1952

By R. M. Larsen

The Rocky Mountain region is defined with some variations for different purposes or by different organizations. For oil and gas development, Wyoming, Montana, Colorado, northwestern New Mexico, and Utah are included in the order of their apparent importance. Portions of adjoining states, such as North and South Dakota, Nebraska, Arizona, Nevada, and Idaho, arc attributary to this region, but have little or no oil or gas production. Nebraska and New Mexico are considered separately (see pp. 412 and 415), and most of the discussion in this report will be confined to Colorado, Montana, and Wyoming. Utah has produced about 200,000 bbl. of oil from the San Juan and Virgin fields, which are isolated and shut in at present. The Clay Basin field in northeastern Utah produces natural gas and distillate, and the Farnham field in central Utah produces carbon dioxide gas. Other Utah areas of some interest are listed in Table I. The Cedar Creek (Baker-Glendive) field in southeastern Montana extends into North Dakota, but is listed under Montana. The other states are in the main wildcat areas, and exploration in 1944 was at a minimum. However, geological and geophysical parties are reviewing them for further testing. Oil production in Colorado, Montana and Wyoming was 459,000 bbl. more than in 1943. Increases of 713,000 bbl. in Colarado and 731,000 bbl. in Montana offset a loss of 985,000 bbl. in Wyoming. This was the first decline in Wyoming since 1938. Field production figures and state totals are given in Table I. Total drilling activities in these three states and Utah increased from 687 wells making 1,442,511 ft. of hole in 1943 to 916 wells making 2,245,803 it. in 1944. Wildcat drilling increased from 163 wells making 331,193 ft. of hole in 1943 to 171 wells making 389,144 it. in 1944. These figures include all drilling wells making footage, not starts or completions, and represent an all-time high in drilling. The year 1944 witnessed the greatest concentration of seismograph activity that the region has had. The Rocky Mountain Oil Scouts Association reported that in 1943, the previous peak year, 91 crew months of work were performed; in 1944, the time was 254 crew months. About 67 per cent of the work was in Wyoming, 18 per cent in Montana, and 12 per cent in Colorado. Twenty-three blocks totaling 400,000 acres were reported assembled in Colorado, and 161 blocks totaling 4,000,000 acres in Wyoming. Information about other states was not given. Fourteen unit agreements were approved by the Department of the Interior, as compared with 13 in 1943. The 1944 agreements were all in Wyoming. In five of the unit areas, oil or gas discoveries were made, four were dry, and five were drilling Or pending' Oil companies find it advantageous to unitize blocks containing any proportion of public domain. Units for

Jan 1, 1945

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid binary and ternary Fe-Ni-Co alloys has been measured by the Sieverts' method between 1550°and 1700°C. Solubility data and standard free energzes and enthalpies of solution for nitrogen in the alloys are presented. Interaction parameters are discussed and presented for binary and ternary alloys. MOST of the studies of nitrogen solubility in liquid metals have been directed toward the dilute alloys of iron. Several of these investigations have included measurements of the nitrogen solubility in Fe-Ni al10s'- and in Fe-Co alloys.435 There has been some work, however, that has extended across the e-i-" and F-CO" binaries. This investigation was undertaken to determine the nitrogen solubility in both binary and ternary alloys of the Fe-Ni-Co system. It was also hoped that the differences between earlier studies might be resolved. EXPERIMENTAL METHOD This investigation was made using a Sieverts' apparatus described previously." The nickel (99.85 pct) and cobalt (99.9 pct) were obtained from Sherritt-Gordon Mines, Ltd., and the iron (99.95 pct) was Fer-rovac-E obtained from Crucible Steel Co. Recrystal-lized alumina crucibles were used throughout the entire investigation with no evidence of crucible-melt reaction. Melt temperatures were measured with an optical pyrometer and the temperature scale calibrated against the melting points of the three pure metals. The emissivity of the melt was assumed to be a linear function of composition for all alloys, as has been shown for Fe-Ni alloys.lZ The emissivity of the pure metals at 1600°C were taken as 0.43 for iron, 0.44 for cobalt, and 0.45 for nickel. Using these emissivities, the trans mis sivity of the system was found to be 0.51 i 0.01. The Sieverts' method was used for this study and followed the procedures outlined previously.l' The individual metals were weighed to give about 100 g of alloy. The alloys were melted in the crucible under a partial pressure of argon. The system was evacuated, and the "hot volume" was measured with argon. To avoid the errors caused by vaporization, the melt was held under vacuum only long enough to ensure that all of the gas in the system had been removed. The influence of any small amount of vaporization on the "hot volume" was shown to be negligible by measuring the "hot volume" after a run. This measurement agreed with that made at the start of the run within the implicit error, 0.2 cc, caused by the limitations in accurately reading the buret. The solubility-pressure relationship was measured in the pure metals and in several alloy compositions throughout the ternary system. These measurements were made by admitting measured amounts of nitrogen to the system, and then determining the equilibrium nitrogen pressure above the melt. This method has the distinct advantage of higher accuracy, particularly at lower pressures, than measurements made by withdrawing gas from the system to reduce the pressure after determining the solubility at 1 atm nitrogen pressure. This latter method has a practical lower limit of about 0.4 atm where an increased error is encountered because the buret must be emptied to permit further measurements at lower pressures. By determining the relation between apparent solubility and pressure, it was possible to make a good estimate of the initial nitrogen content of the metal from the intercept of the solubility curve extrapolated to zero pressure.11 DISCUSSION The solubility data corrected to 1 atm nitrogen pressure are summarized in Table I. The reported solubility has been corrected for the initial nitrogen content of the alloys. The initial nitrogen contents fell between 0.0002 and 0.0010 wt pct, and were lower in the iron and nickel than in the cobalt. Sieverts' law was obeyed in all alloys at pressures up to 1 atm. Examples of this behavior are shown in Fig. 1. The reaction for solution of nitrogen is Taking the standard state as 1 wt pct N in the alloy and the reference state as nitrogen at infinite dilution in the alloy, and noting the adherence to Sieverts' law, K becomes the solubility of nitrogen in the alloy at 1 atm pressure. Thus the solubility data of Table I were used directly to calculate the standard free energy for the solution reaction. These results are also presented in Table I. The enthalpy of solution is also summarized in Table I as calculated from a form of the van't Hoff relation: Iron-Nickel System. The data for the solubility of nitrogen in liquid Fe-Ni binary alloys is presented in Fig. 2 along the with data of aito, Schenck et al.,' and Humbert and 1liott.l' The data for studies of nitrogen solubility in Fe-Ni alloys containing less than 20 pc t i'- are not presented in Fig. 2, although they are in good agreement with the present work. The results of this study are in good agreement with Schenck

Jan 1, 1967

By John Hays Hammond

IT was but a few years ago that the mining engineer, and his confreres, the civil, mechanical and electrical engineer, were stigmatized by politicians of the parish? pump variety as advance agents of unprincipled exploiters of backward countries. Today he is recognized as a most important missionary of civilization in opening up new territory to contribute its mineral wealth and incidentally its other resources for the needs of mankind. An engineer, it is now conceded, is not only a benefactor of the world at large, but is a primary factor in the betterment of conditions of the inhabitants of those countries developed by his skill and indomitable courage-for courage is requisite in pioneering and his indefatigable industry. The engineer will, I believe, become a real "Ambassador of Good Will," when the slow-consenting academic mind realizes as it must that beneficent deeds are more enduring and more convincing than mere gestures of professed amity.

Jan 1, 1929

By L. Leibowitz, M. G. Chasanov, L. W. Mishler

A drop calorimeter system is described for use in measuring enthalpies to 3600°K. Data are presented for tungsten between 2800" and 3600°K. The enthalpy of tungsten in cal per mole between 2000° and 3600°K can be represented by the equation HºT- Hº298 = - 1.7622 X 103 + 5.7772T + 8.9861 where T is in degrees Kelvin. A tabulation of com -puted values is presented for heat capacity, entropy, and free energy function. A drop calorimeter has been constructed to carry out enthalpy measurements at temperatures to 3600°K. Samples are heated by induction1 and dropped into a commercial adiabatic calorimeter, modified for this purpose. The experimental temperature is limited by the melting point of container materials and compatibility of the container and its contents. Several high-temperature drop calorimeters have been described in the literature1-5 but none has been used at temperatures as high as those in the present work; our measurements of the enthalpy of tungsten range from 2800" to 3600°K. DESCRIPTION OF EQUIPMENT An overall schematic view of the equipment is shown in Fig. 1. Power for the induction coil is supplied by a 25-kw 250 kHz Ther-Monic generator coupled to an iron core RF transformer. The Sample capsule is suspended in the work coil by 10-mil diam tungsten wires which are wrapped around a horizontal 5-mil diam tungsten wire. The horizontal suspension wire is clamped between two massive copper electrodes which are fixed in an x-y motion device that allows adjustment of the position of the heated capsule from outside the vacuum chamber. The copper electrodes are connected by flexible copper straps to a 1250-joule (5 kv, 100 pfarad) condenser bank. When it is desired to release the capsule, the condensers are discharged through the horizontal suspension wire causing it to vaporize rapidly. Very reliable and precise release of the capsule is achieved in this manner. Experiments have shown that no heat correction is required for this discharge energy. As part of the temperature measuring system, two prism holders have been incorporated in the apparatus. The upper prism holder is in the main vacuum chamber itself, whereas the lower one is in a side arm attached to the drop tube below the gate valve. The upper prism is mounted on a rotary vacuum feed-through, and may be moved under a protective shield when not in use. This prevents deposition of vapors on the prism surfaces when temperature measurements are not being made. Similarly, the lower prism is mounted on a push-pull vacuum feed-through, and when not in use may be pulled into its side tube. The prism mountings are fitted with guides and stops so that they may be moved precisely into the desired position. The aim throughout is to minimize the time the prisms are exposed to vapors from the hot samples. At the high temperatures reported in this paper, only the lower prism was used. The upper prism holder in these cases was fitted with an additional radiation shield. By using a prism and viewport, the lower surface of the samples can be observed by an optical pyrometer. The measurements discussed in this paper were obtained with a Leeds and Northrup 8622-C-S series manual pyrometer which is estimated to be accurate to 0.5 pct. Pyrometer calibrations and prism and window corrections were carried out in the conventional manner6 using tungsten strip lamps calibrated by the National Physical Laboratory, Teddington, England. Prism corrections were rechecked after each use. All work to date has been done in vacuum, and no measurable change has been observed in the prism correction below -2300°K for the upper prism and below -2800°K for the lower one. The total time of exposure of the prisms is about 50 sec per run. At high temperature, the final temperature reading is corrected by using the final A value for the prism; see Ref. 6 for details of this procedure. The calorimeter is a modified Parr Instrument Co. (Moline, lll.), Series 1230 adiabatic calorimeter with automatic jacket control. Other authors5 have used a similar calorimeter with good results. The calorimeter jacket cover and calorimeter cover are attached to the drop tube which contains a radiation shield. This shield is a gold-plated copper disc which can be operated manually from outside the calorimeter. The receiver is attached below the radiation shield and is lined with tungsten. In a typical experiment, the calorimeter and its jacket water temperatures were adjusted to 0.000°K temperature difference. The sample was allowed to equilibrate in the furnace at the desired temperature for about 20 min. The initial calorimeter temperature was then recorded, the sample dropped, and appropriate shutters closed. After about 3 min, the drop tube and receiver were filled with helium to 60 torr. The final calorimeter temperature was recorded after it had remained constant over a 5-min period. The equilibration time in the calorimeter was about 25 min. Thermistor probes are used to operate a hot and cold water supply system to maintain the jacket temperature equal to the calorimeter temperature. For actual measurements of the calorimeter temperatures, a quartz thermometer was used (Hewlett Packard Dymec Thermometer, Model #2801A). This thermome-

Jan 1, 1970