Search Documents

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By Corliss R. Kinney

Since the first atomic bomb exploded over Japan, a great deal of speculation has been published about the use of atomic energy instead of coal for the production of power. Atomic energy, in time, may displace coal for this purpose, but atomic energy will not displace coal in supplying chemical raw materials to the rapidly expanding carbon-chemicals market. Modern civilization demands large quantities of carbon compounds and the logical source of many of these is coal. Consequently, many progressive operators are considering the possibilities of the utilization of coal as a chemical raw material as never before. Furthermore, the demand for clean, smokeless, and ashless fuels will continue to increase and the only way to handle coal under those conditions is to take it apart, just as crude petroleum is taken apart. One can readily imagine where the petroleum industry would be now if it had insisted on selling customers only crude oil, perhaps emulsified with a little salt water to correspond to the moisture and mineral matter in raw coal. The time seems to be coming at an accelerated Dace when mine operators will find that competing for a highly selective fuel market by producing a larger tonnage at smaller cost will be less profitable than to increase the value of a smaller tonnage many fold by producing something more valuable to industry and civilization than raw coal. For example, about 750,000 tons of carbon black selling for $50 to $60 per ton was produced in the United States in 1945. This tonnage is insignificant compared with the total production of coal in the United States, but a very tidy tonnage, together with the coal necessary to operate the process, for any mine operator fortunate enough to obtain a method of producing a better carbon black from coal. From the point of view of tonnage, the manufacture of coke of various kinds and its by-products is at present the most important source of carbon chemicals from coal. Nearly 20 per cent of the coal mined in this country is used for this purpose. A large proportion of the coke is used for the production of iron and steel, but even in this operation a considerable part of the coke is used for a chemical purpose; that is, the reduction of the ore to metallic iron. In addition, large quantities of coke are used in manufacturing many important products that find their way into the market. Possibilities of Acetylene One of the important chemicals manufactured from coke is calcium carbide, from which many products are made. One of these is acetylene. This hydrocarbon can also be manufactured from natural gas or from waste oil-refinery gas and these industries will probably offer competition for the manufacture of acetylene. Coke-oven gas can be used for making acetylene and should receive consideration

Jan 1, 1947

By F. J. Fayers, R. L. Perrine

For many years the problem of increasing ultimate recovery of oil from a reservoir has been a subject of interest to the oil industry. At present, a standard secondary recovery technique is to flood the reservoir with water once natural forces of the system are depleted. The permeability characteristics of the rock, together with interfacial forces which exist between the two fluids and the porous material. allow only part of the oil in the rock formation to be recovered by the water-flooding process. Laboratory experiments have shown that when detergents are added to the flooding water, the flow properties of oil in a porous rock arc improved. This improvement results in greater oil recovery. Even though higher recoveries are obtained using detergents, the extra cost associated with the method may make it economically unsatisfactory. To establish economic feasibility requires experimental laboratory measurement of fluid and rock properties together with a calculational procedure to predict field results. Pilot tests in the field may also be required. This paper presents a mathematical procedure for predicting detergent flood behavior. A number of reasonable simplifying assumptions are made to obtain a tractable system of equations. The resulting method may be regarded as a generalization of Buckley-Lev-crett' theory to solve simultaneously for water saturation and detergent concentration profiles. Consequently this type of calculation can be used in much the same manner as Buckley-Leverett theory is used to evaluate a water flood. The mathematical method employed is the so-called method of characteristics for solving hyperbolic partial differential equations. This application of the method is instructive because several other problems in reservoir analysis may be analyzed in a similar manner. FLUID FLOW EQUATIONS The flow behavior of oil and water without detergent through porous reservoir rock is usually expressed by Darcy's law and a continuity equation for each phase. If gravitational forces are neglected, vrg = kr (s)µr v p rg.........(1) vrg = kr (s)µr v p rg.........(1) ? pa va = F ?/?t (sd) where v is the volumetric flux, k represents permeability, S is saturation, and P the pressure. Fluid viscosity is denoted by 11, p is the density, 4 is porosity, and I the time. The subscripts w and o refer to water and oil. The capillary forces in the system lead to a difference in pressure between phases. This may be expressed by the relation: Pm -P0 =Pc(S).........(5) The capillary pressure? P,, is determined experimentally as a function of saturation. DETERGENT BALANCE EQUATION Addition of detergent to the water phase affects the flow properties of the system. Capillary pressure and relative permeability become functions of detergent concentration, c, as well as fluid saturation. That is: P--P (S,c) and k,,,.- - -- k,,,. At low oil saturation values, the presence of detergent reduces capillary pressure and reduces the relative permeability ratio. Detergents are surface-active and adsorb on rock surfaces. The quantity adsorbed, a, will depend on the concentration c of detergent solution and may also depend on the saturation; thus, a = a(S,c). In this analysis we have assumed that the detergents used are water soluble but not oil soluble, and their movement is therefore restricted to the water phase. The dispersion of detergent in water is neglected by comparison with transfer by flow within the system. Detergent movement is determined by the water flux and adsorption: ? cv m = -F ?/?t (cs + a) We will assume that the quantity of detergent in solution is too small to significantly change water density or viscosity. When the permeability and capillary pres-

By L. J. Dijkstra, R. J. Sladek

IN earlier work the effect of manganese on the general behavior of nitrogen in iron was the subject of a careful examination by Fast.' Part of the investigation was made, in collaboration with one of the present authors (L.J.D.), by using the internal friction method. This technique, which has been described elsewhere,' showed some significant changes in the properties of Fe-N alloys by the addition of a small amount of manganese namely: 1—Under standard conditions the maximum of the nitrogen peak in pure iron appears around 20 °C and the half width is about 27 °C. By addition of 0.5 atomic pct Mn a general broadening of the internal friction peak occurs. The half width is increased by about 9°C. Moreover, a shift of the maximum of about 5°C toward a higher temperature takes place, Fig. 2. 2—The precipitation of nitrogen from the supersaturated solution, measured, e.g., at 200 °C, was inhibited by the addition of the amount of manganese given in effect 1. The broadening of the nitrogen peak was confirmed in more recent work3 on samples which were prepared from Westinghouse Puron iron. The effect of manganese on the rate of precipitation, however, was much less striking than in the earlier work' based on Philips high purity iron. Theory To explain the first change in properties just referred to, effect 1, the following two assumptions were made:' First, every manganese atom in sub-stitutional solid solution creates around it six interstices located between an iron and a manganese atom, as is evident from Fig. 1. These interstices, conveniently called Fe-Mn interstices, have for nitrogen a free energy level which is AG* lower than the normal Fe-Fe interstices between two iron atoms. For such low concentrations of manganese as 0.5 atomic pct, the possibility that two manganese atoms will be nearest neighbors can be disregarded. Second, it is assumed that in addition to the normal relaxation time TFe at least one new relaxation time, Mn, Fe, enters in the phenomena which is associated with the elementary diffusion jumps between a Fe-Mn interstice and an adjacent Fe-Fe interstice. Fig. 1 gives schematically the free energy for a nitrogen atom as a function of its position along the line ABC. A tentative analysis of the nitrogen peak in a 0.5 pct Fe-Mn alloy based on these assumptions has been made in Fig. 2. The dotted curve with a maximum at 22°C is caused by jumps between Fe-Fe interstices, the dotted curve with maximum at 32°C by jumps between an Fe-Mn and an Fe-Fe interstice. The two effects added together give the dash-dot internal friction curve for the alloy. In the following these two components will be referred to as the normal peak at 22°C and the abnormal one. (The small secondary peak at

Jan 1, 1954

By W. M. Wojcik, R. F. Kowal

Oxygen and sulfur distributions in commercial, 5-ton ingots of killed, medium carbon steel are described. Oxygen distribution is found to vary with deoxidation practice. Irregular distribution of oxygen within ingots makes necessary special precautions in sampling of rolled products for analysis of oxygen. Oxygen distribution is discussed in terms of recently published solidification concepts which had been successfully applied to simpler cases of segregation. These concepts have been found inadequate to explain observed oxygen distributions. Convective movements of the liquid metal, as determined by tracer elements, are shown to be capable of accounting for the observed distributions of oxygen. IN an effort to explore the origin of surface and subsurface imperfections in pierced steel products, a study of oxygen and sulfur segregation was made on ingots cast in open-top and hot-top molds. The results of our previous investigations1"3 have indicated the importance of the location and amount of oxide inclusions in an ingot. Inclusions close to the surface of the ingot have been found to contribute greatly to the formation of imperfections in the surface of finished products. This study of the effects of deoxidation and casting practice on segregation and the resulting oxygen distribution in ingots was initiated to determine the parameters controlling the location of inclusions in an ingot. Segregation of solute elements during solidification of low-melting binary alloys has been studied in the past.1, 5 Formation and growth of inclusions in iron melts have been studied under specific conditions."- In spite of these and other recent studies,10-12 segregation during solidification of commercial, killed steel ingots is not well understood. Consideration of solidification rates, of segregation during solidification of the chill, dendritic, and central zones, and of material balances for the segregated elements has indicated that a simplified theoretical solidification model is not adequate. However, the observed high oxygen contents in localized volumes of the dendritic zone can be rationalized if additional effects of convection currents in the ingots, precipitation, and rapid growth of new phases are considered. EXPERIMENTAL PROCEDURE Steelmaking and Processing. A group of nine killed. medium carbon steel heats having compositions listed in Table I have been studied. The deoxidation and mold practices used were varied to give a wide range of steel oxygen contents. The amounts of aluminum added to the ladle and the ingot casting practices (hot top and open top) were the main variables. The steel was made by a duplex practice in 160-ton tilting basic open-hearth furnaces. All nine heats were top-cast into 24 by 24 in. big end down, fluted molds, to a height between 60 and 76 in., using both open tops and exothermic hot tops. The deoxidation practice and the tapping and teeming details for each heat and ingot studied are given in Tables II and III, respectively. Hot-top practice is indicated by the letter H following the heat designation. Furnace and ladle temperatures were measured by standard disposable-tip, Pt/10 pet PtRh thermocouples. Teeming-stream temperatures were obtained as described by Samways et al.,13 by immersing a Pt/10 pet PtRh thermocouple, covered by a silica sheath, into the teeming stream under the nozzle. The output of this thermocouple was recorded with Leeds & Northrup Speedomax potentiometer. Calibration of the latter thermocouples was based on the freezing point of a pure iron/oxygen alloy (2795°F). The accumulated errors of measurements were within ±10°F. The thermocouple measurements were supplemented in this investigation by continuous recording of a ratioing, two-color pyrometer (Shawmeter), protected from smoke by a blast of clean air within the sighting tube, and calibrated to read with better than ±10°F accuracy. Following teeming of three heats, P, R, and T, tracer elements were added to the steel in the molds to obtain a record of the progress of solidification. As soon as the teeming stream was shut off, a 0.010-in.-thick steel can containing a mixture of crushed standard ferro-titanium and ferro-vanadium (0.05 pet of each alloy element) was plunged into the middle of the steel pool to a depth of 6 in. In about 30 sec no indication of the can or its contents remained. The surface of the open-top ingots solidified in 20 to 30 sec. A study of liquid metal movement and the precipitation of oxides was facilitated materially by use of the tracer technique as titanium has a low distribution coefficient between solid and liquid steel while vanadium has a high distribution coefficient.

Jan 1, 1965

CARL HENRICH (communication to the Secretary*).-I have read with much interest the discussions of my paper by Messrs. A. S. Dwight, E. P. Mathewson, Win. B. Boggs, Jos. W. Richards, and W. C. Smith. Mr. Dwight's acknowledgment that he always-in lead smelting¬obtained better results by figuring A1203 as an acid in his slags, I may take as a confirmation of my views, notwithstanding his later conversion by, the late T. S. Austin to the latter's empirical view and way of neglecting the consideration of A1203 altogether in the composition of slags-letting the slags "dissolve" in Al203. I have a strong suspicion that Mr. Austin, in a large custom smelting plant at El Paso, has been able to keep the alumina percentage of his slags sufficiently low, not to give him much trouble, although I have also a suspicion that his furnace foreman may have had a somewhat differing opinion of the practical working of the "dissolving" theory,, whenever its applicability was tested to its limits. That Austin should have conceived the notion that the Ca of CaF2 would enter into a slag as CaO, seems hardly in accord with the recognized ability of that late metallurgist. It is a well-recognized fact that even small amounts of CaF2 will reduce the viscosity of a slag; but I did not think anyone ever had an idea that CaF2, in some mysterious way, parted with its F and coupled itself with 0 to satisfy a craving for CaO on the part of 802-least of all in a lead furnace. The "dissolving" theory for CaF2 was doubtless appropriate, and an improvement on figuring the Ca of CaF2 as CaO to satisfy the demand of Si02 for RO bases. However, I cannot understand the rationality of extending this "dissolving" theory to A1203 and to ZnO. It would be interesting to have more specific data from Mr. Mathewson in regard to the actual composition-analyses-of the slags made, when he had these unusually high alumina slags in Colorado. We "old" smelters all know that within certain limits, usually found out by rather tough experience, we could safely "disregard" A1203. In fact, I believe, we never really analyzed for alumina, except in slag analyses, when we

Jan 6, 1917

By F. M. Leonard

Churn-drill hole sludge samples have proved their reliability at Cananea

Jan 5, 1951

By D. S. Pye, J. P. Gallus

Successful hydraulic pressure treatment of oil and gas wells that have long producing intervals, multiple pay zones, fluid thief zones, or natural or induced fractures has long been a serious problem plaguing the petroleum industry. High fluid-injection rates, straddle packers, ball sealers, and either liquid or solid additives to the treating fluids are being used to cope with this difficult and costly problem.l-6 The use of ball sealers and straddle packers is limited, in practice, to wells that have been completed with perforated cemented casings or liners. Well stimulation with ball sealers and straddle packers is usually successful as long as the cement remains competent. The other techniques of diverting are used with all types of completions. However, there are two significant disadvantages of the high rate method: excessive horsepower requirements, and the need of large treating-fluid volume. Consequently, most well stimulation techniques that involve diverting depend upon ball sealers or granular materials. Liquid diverting agents, and some of the solid ones in use today, frequently will cause formation damage. On the other hand, the most popular particulate diverting agents often are so soluble in the treating fluid that they become largely ineffective; their particle size is severely reduced as they dissolve while being transported through thousands of feet of pipe to the formation face down hole. In our attempts to deal with the shortcomings of these diverting agents, we experimented with a large variety of potentially suitable deformable materials the solubility of which could be controlled. Following are the criteria for the diverting agent sought: 1. The material must be effective in reducing fluid loss to thief zones, including existing fractures and very high permeability layers in the formation to be pressure treated. 2. The material must have enough strength to bridge under the treating pressure. 3. The material must be insoluble or slowly soluble in the treating fluids so that the particles retain sufficient size to be effective after they reach the formation face. 4. The material must be completely soluble in the produced oil or condensate liquid so that it can be removed readily; it must not cause formation damage. A number of products consisting of various polymers blended with waxes and other solid hydrocarbons were examined. All these materials satisfied the criteria for a diverting agent and also exhibited some degree of plastic deformability. On the basis of initial tests of strength and hardness, several blends of wax and polymer were selected for extensive testing in the laboratory and the field. These compounds have congealing temperatures ranging from 140 to 190F; they are insoluble in water and soluble in oil. They conformed, therefore, to the criteria specified for a theoretically superior diverting agent. Laboratory and field tests were conducted using these wax-polymer materials to demonstrate that the use of a deformable diverting agent can significantly improve fluid diverting performance. Data in this

Jan 1, 1970

By C. H. Green

. RECENTLY two papers on the structure of eutectics were read before the British Institute of Metals, one by F. L. Brady1 and the other by A. Portevin.2 In the preparation of photomicrographs of laboratory specimens as illustrations for student work, and in connection with various researches; the writer has been working along the same line for some, time and, therefore, was much interested in the results given, especially those of Portevin. He has correlated the information on the subject and has outlined a broad scientific basis for future work along this line. It is largely with the idea-of adding something by way of illustration to the work already done that this paper is written. The eutectic is generally understood to mean the alloy having the lowest melting point of any alloy of the system, and in which the melt becomes supersaturated with reference to the two or more phases which, separate out simultaneously (or alternately). From the surface pattern, the eutectic means; a structure with no primary crystals. It is not always easy to get the exact eutectic composition in making any alloy; in fact, a slight range in composition may be expected and some of the coarser particles may be richer in either of the composing metals. Even when chemical analysis shows the right composition, differences in density of the pure metals may cause segregation, or. supercooling resulting from different crystallizing properties may give a surface pattern the appearance of being on one side of the eutectic point. However, the alloys on either side of the eutectic composition, showing primary crystals of one of the phases and the effect of the pro-eutectic form on the surface pattern of the eutectic make a very interesting study, which is slightly touched upon in this paper. The phases, or microconstituents, of a eutectic may be pure metals (Pb-Sb, Tl-Au), solid solutions (Cd-Zn), a pure metal and a solid solution; (Ag-Sn), or a pure metal or solid solution with an intermetallic compound (Sb-Mg, Sb-Cu, As-Cu, Bi-Te, etc.).

Jan 2, 1925

By W. J. Slatosky

W. 0. Philbrook (Cairiegie Institute of Technologyogv—Mr. Slatosky has presented an interesting and constructive paper that represents another step along the way of converting steelmaking from an art to a science. I am confident that his computer will be practical and successful and that with a very few months of experience it will provide a significantly better degree of control than his record of 65 pct of heats within range obtained with the slide-rule calculator . A paper such as this, with a lot of symbols and condensed mathematics, is difficult to comprehend quickly. Since I have had an opportunity to study it carefully, perhaps my evaluation of its validity and accomplishments will save time for others. Mr. Slatosky has correctly used standard principles of stoichiometry and heat balances, which are available to anybody, but he has also brought to them two original contributions: 1) He has developed from operating data some empirical relations for predicting the final FeO content of the slag (at 0.5 pct C end-point) as a function of slag basicity, lance height, and scrap, ore, and scale in the charge. This improves the accuracy of prediction of temperature or scrap requirement compared with assuming an arbitrary, constant FeO content at the end of each heat. There is no assurance yet that exactly the same relations will hold for other furnaces or practices, but similar correlations can be expected. 2) He has combined calculations that are ordinarily carried out laboriously as a number of individual steps into a single, simple linear equation that can readily be fed into a machine. This involved a tremendous amount of painstaking detail work as well as the imagination to see the possibility and work out the steps. While his particular Eqs. [3] and [6] are valid only for the furnace design, charge weight, and blowing time used at Aliquippa Works, only a few numerical values have to be changed to adapt it for other conditions. In order to arrive at a useable solution, Mr. Slatosky had to make some basic assumptions about the process that are similar to those used by others. He neglected variation in some process variables and assumed an arbitrary average value for waste gas analysis and temperature for want of more exact information at the present time. All of these judgments are clearly stated. In addition, some thermody-namic data presently available are not adequate for the job, notably in relation to heats of formation and sensible heat in slag, and some expedient has to be adopted to get around the difficulty. Other people might prefer slightly different judgments about these details and hence obtain somewhat different numerical solutions. This is not of serious importance, however, because the errors accumulate in the "heat loss" term and are largely self-compensating for a constant heat time. Although the extended Eq. l(a) in Appendix I was set up as a rate equation originally, for convenience in using an analogue computer as stated in the paper, the time dependence was removed by later mathematical manipulations and assumptions about the process. The final result is an integration of element and energy balances from initial to final states; this procedure is as legitimate here as in any other form of heat-balance calculation. The formal handling of stoichiometry and thermochemistry appears to be correct, and it is assumed that any arithmetical errors would have come to light in applying the calculations to furnace practice. Mr. Slatosky's approach is not necessarily unique, in that other people might start with apparently different equations or prefer another form of final equation for another type of computer. However, he has presented an accomplished result that appears to be a theoretically sound and practically useful way of applying scientific principles and rapid computation for better control of steelmaking. His success will undoubtedly encourage himself and others to improve on the mathematical model and its use as better informatioq becomes available. John F. Elliott (Massachusetts Institute of Teck-t2ology)-The last comment by Mr. Richards that a calculator is quite unnecessary for an L-D operation ?-equi??es a rebuttal. The L-D furnace is a very high capacity process which places a premium on close control. When one is making steel at rates between 100 and 200 tons per hr, one cannot afford the luxury of an extra 5 or 10 min at the end of a heat correcting for an error that should never have been made in the first place. Mr. Slatosky's paper is a very sound application of the simple principles of stoichiometry and the energy balance. It is a satisfactory and valuable start, but only the start of the development of methods of control for this process. An analysis of the process shows that it should be very suitable to control by a computer. This is especially the case when various grades of steel are to be made. In fact, it would seem that the organizations who are planning new and bigger installations of L-D vessels should consider carefully the advantages that would stem from computer control of a vessel with the operator present to do little more

Jan 1, 1962

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By Strathmore R. B. Cooke, Eugene L. Talbot

THE perfluoro acids and derivatives show unusual surface-active properties that qualify them as possible flotation reagents. They lower the surface tension of water from 15 to 20 dynes below that obtainable with the corresponding hydrocarbon compounds.1, 2 Fluorochemicals adsorb very strongly on solid surfaces to give films that exhibit larger contact angles than films of the corresponding hydrocarbons."&apos; * The large contact angles probably result from the terminal —CF3 group. The perfluoro acids are made by electrolysis of the corresponding carboxylic acid in anhydrous hydrogen fluoride.5 From the perfluoro acids many derivatives may be obtained, such as amides, amines, alcohols, xanthates, ethers and esters and others. Since the fluorinated analogues of the conventional hydrocarbon flotation collectors possess enhanced surface properties, a few were selected for testing. Because a survey of all possible minerals and reagent combinations would be out of the question, hematite was chosen to represent a nonsulphide system and pyrite to represent a sulphide system. The fluorinated reagents used in these experiments were prepared in the research laboratories of Minnesota Mining & Mfg. Co. Some were synthesized especially for this research. They are not available cokmercially. Separation of Nonsulphide Ores: The separation of oxides from silica has always been a challenge to the flotation industry because differences in surface properties of the minerals are normally insufficient to produce clean concentrates. Oleic acid," rosin acids,&apos; and amine salts% ave been used to considerable extent to effect separation of metal oxides and silica. The system hematite-silica was chosen to represent the nonsulphides both because of its difficulty of separation and because large tonnages of easily obtainable material are available, such as gravity concentration tailings and nonmagnetic taconites on the Mesabi Range. The wash-ore tailings used here contained approximately 35 pct iron after desliming. Samples of the material used in this work were part of the same lot used by Chang, Cooke, and Huch9 and were prepared in an identical manner. Reagents for Nonsulphide Ores: Since one of the purposes of this investigation was to compare hydrocarbons with fluorocarbons, reagents of known behavior such as oleic acid, and the alkali metal salts of certain resin acids (Dresinates), were established as standards. Hydrocarbons and fluorocarbons of comparable chain length and other experimental fluorocarbons were tried as collectors for hematite. A list of the materials used and the concentrations of their stock solutions are given in Table I. Since silica can be selectively floated from hematite by conventional reagents," a few fluorocarbon reagents were also tried for this purpose. Their composition and concentrations are given in Table 11. Most of these reagents served the dual function of collector and frother. In the case of F-11 flotation did not occur but it served as a frother when F-6 was employed as a collector. Reagent grade sulphuric acid and sodium hydroxide were used to regulate the pH. Deionized water containing less than 0.1 ppm of salts expressed as NaCl was used for all solutions and flotation tests. The pneumatic flotation cell consisted of a 350-ml fritted glass Buechner funnel with a source of filtered air which could be controlled by a needle valve." A 50-g sample of ore and 250 ml of deionized water were added to the flotation cell and stirred slowly. The reagents were added and the pulp was conditioned before air was admitted to the cell. Approximately 15 ml of the pulp were removed for pH determination before flotation was started and were then returned to the system. The pH was again measured after flotation. Air was admitted to the cell until no further flotation occurred or until the character of the float changed markedly. Both the float and the nonfloat products were filtered, dried, weighed. and assayed for iron. The cell was washed in hot water and rinsed with deionized water after each test. Occasionally the cell was cleaned with concentrated hydrochloric acid to remove iron oxide particles from the glass frit. Experimental Results: Above a pH of 8, sodium oleate was an effective collector for hematite. The emulsification of equal parts of heavy fuel oil (20"

Jan 1, 1956

By AIME AIME

WILBER JUDSON is one of that fairly large group of mining engineers that graduated at an Eastern college, worked his way up in various jobs in the West and in the Latin-American countries, and finally came to New York as an administrative officer of a large mining company. Since coming to New York he has been a loyal friend and counselor of the A.I.M.E., and is now serving a second term as one of its Directors, his first term covering the period 1935-1938. Mr. Judson was born in the capital city of Michigan on July 26, 1880. Probably it was his roving spirit rather than professorial urging that was responsible for the fact that four colleges were responsible for his education: Northwestern, University of Michigan, Harvard (S.B., 1901), and the Michigan College of Mines (graduate study). In his first ten years of professional work he might have been found serving as mine foreman at Catamarca in the Argentine, as superintendent of the Inter Ocean mine at Sunshine, Colo.. as foreman for the Cerro Prieto, Magdalena, Sonora, as superintendent of the Hudson Iron Co. in New York, or as manager of the Dolores mine in Chihuahua for the Mines Co. of America, or in Spain, or in Panama.

Jan 1, 1942

By G. E. Agar

The energy required for dry grinding of phosphate rock in ball and roller mills has been analyzed by the method suggested by Charles and others. The findings are not wholly in agreement with Charles&apos; predictions; but, nevertheless, the method of analysis is shown to be sound. Some of the deviation is probably attributable to the characteristics of a dry grinding system. Many laboratory and pilot plant scale experiments have been made to determine the energy requirements for size reduction. This topic was recently reviewed by Agar and Brown&apos; and it was apparent that very little if any data exists in the literature which permits one to apply the Charles 2-Holmes3 analysis to industrial size systems. More recently, the idea has been put forward that the postulate of comminution by impact used by Charles and others was not sufficient to explain size-reduction throughout the grinding operation. The opportunity exists in the grinding operations of International Minerals and Chemical Corp. (IMC) to analyze the energy-size relationship for dry grinding phosphate rock in both ball and roller mills. This situation arises because the mills are used for custom grinding and make products from 50% to 85% minus 200 mesh. BACKGROUND A correlation of particle size in a comminuted material with the energy expended in size reduction was proposed by charles2 to be of the form

Jan 1, 1965

By A. E. Bibb, F. W. Kunz

A platelet form of zirconium hydride was found in zirconium and ZY-1 wt pct U single crystals containing hydvogen in the range of 50 to 100 ppm. The habit planes for the hydride plateletg in the zirconium crystals were found to be {1012}, {1121}, and (1122) while the habit planes in the ZY-1 wt pct U crystals were {1121), {1123}, and (1.231). With the exception of the {1231} plane, these have been identified as the twin planes in zirconium. The different effect of hydridc on the mechanical puoperlies of zirconium at high and low strain rates has been explained in terms of the defornzation mechanism and the habit planes of the hydride. ZIRCONIUM and zirconium-base alloys are considered for many nuclear reactor applications, where the pick-up of hydrogen is a distinct possibility, if not an unavoidable occurrence. An excellent example of this is the absorption of hydrogen by zirconium and its alloys during aqueous corrosion, where as much as 30 pct of the hydrogen produced by the corrosion reaction is picked up by the metal. Under the proper conditions, the absorbed hydrogen would precipitate as zirconium hydride and consequently alter the mechanical and physical properties of the zirconium-base alloys. The knowledge obtained from a study of the crystallographic aspects of the hydride precipitation is necessary for the interpretation of the observed changes in the mechanical and physical properties. The deleterious effect of hydrogen on zirconium-base materials is not always observed in normal slow tensile loadings at or above room temperature, but becomes immediately obvious under impact loading, where the energy absorbed decreases with increasing hydrogen content,&apos; and in notched specimens where triaxial loadings are attained.2 This effect is of serious consequence in the applications of Zr where shock loads or high strain rates are experienced. The purpose of this investigation was to determine the crystallographic planes of the Zr and Zr-1 wt pct U matrices upon which zirconium hydride will precipitate and to correlate these with the observed mechanical property data. PROCEDURE Crystal Growth—Single crystals of Zr and Zr-1 wt pct U alloy were used in this investigation. The Zr crystals were made from sponge that had a typical analysis as shown in Table I. Large grains were grown in this material by rapid cooling an arc-melted charge in a button furnace. This operation undoubtedly lowered the volatile impurity concentration below those listed in Table I. Back-reflection Laue patterns of these large grains showed the presence of considerable substructure and lattice distortion within each grain. It was found that an 18-day anneal in an argon atmosphere at 840°C (a high a heat-treatment) followed by furnace cooling, resulted in the further growth of the large grains and removed the detectable substructure ana lattice distortion. Equiaxed crystals with a cube edge of approximately 1/4 in. were produced in this manner. Large crystals of Zircaloy-2 (1.5 wt pct Sn, 0.15 wt pct Fe, 0.1 wt pct Cr, 0.05 wt pct Ni) also were produced by this technique but the large amount of substructure formed could not be removed by annealing. The Zr-1 wt pct U solid solution crystals were produced from an alloy rod consisting of Westing-house-Foote hafnium-free crystal bar zirconium and depleted uranium. The chemical analysis of the alloy is also given in Table I. Three-inch sections were cut from an 0.120-in.-diameter alloy rod and tapered to a fine point on each end. The samples were sealed in evacuated Vycor tubes, homogenized for 5 hr at 1000°C in the ß-phase field, and slowly lowered in a gradient furnace into the a phase (800°C), annealed for 60 hr at this temperature to produce grain growth and furnace cooled. This technique produced large grains approximately 1/2 to 3/4 in. long over the entire cross section of the rod, which were free of observable substructure. Metallographic examination up to X1000 did not show the existence of any second phase in these grains. Crystal Orientation—All crystals were abraded on fine emery paper to produce two flat surfaces 90 deg to each other. The crystals were analyzed by the standard Back-Reflection Laue technique to obtain the crystal orientation with respect to the abraded surfaces. The Back-Reflection Laue Photograms of all crystals used were clear and sharp indicating that the crystals were free from any substructure that could be detected by these means. Hydriding—Only samples containing four to five grains were used for hydriding. Samples that exhibited fine grained patches were discarded. The samples were hydrided using the following technique. After etching in 48 vol. pct HNO3, 48 vol. pct H2O, and 4 vol. pct HF (48 pct) solution, the specimens

Jan 1, 1961

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By J. M. Larkin

GOOD will is becoming recognized more and more as a necessary business asset, and a successful concern must have the good will not only of its customers and the public, but of its employees. Management -enlightened management-recognizes this and will go the limit to get it. Progress depends on cooperation, and in industry cooperation must be based on the acceptance by employ-ers and employees of some practical application of the principle that capital and labor are interdependent. Capital cannot exist without labor, and labor without capital is helpless. The development of each is depen-dent on the cooperation of the other. Confidence and good will are the foundation of every successful enter-prise, and these can be created only by securing a point of contact between employer and employee. We feel that one of the most effective agencies for promoting good will between employers and employees is through some well organized method of conference and have consequently adopted, to accomplish this, a plan of employee representation. The plan inaugurated by the Bethlehem Steel Co. about four years ago, which provides for the election by secret ballot of representatives by and from among the employees, has for its purpose three fundamentals; namely, to give the employees a voice in the determina-tion of the conditions under which they work, to furnish machinery for the prevention and adjustment of differ-ences between employees and management, and, so far as possible, to provide and foster continuous employment. The constitution and by-laws adopted take care of the detail in setting up machinery for the functioning of the representatives of both management and men, but the spirit with which the plan has been carried out and the results which have been accomplished are of far greater importance than the plan itself. The Bethlehem plan, which has been in operation since October, 1918, can no longer be classed as an experiment. The original by-laws provided for amend-ments and, as was anticipated, changes and improve-ments have been made from time to time by mutual agreement. The operation of the plan for over four years shows it to be fundamentally sound and that it must therefore be conceded a success.

Jan 2, 1923

Jan 1, 1966