Search Documents

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

By Simon T. Johnson

Potential applications for boom tunnelling machines requires reliable assessment of in-situ performance. The majority of existing classification schemes concentrate on the prediction of excavation rate, neglecting the important influence of tool consumption rates. A statistical approach is taken to the analysis of the performance data, which was obtained first-hand through in-situ monitoring, and laboratory testing of representative rock samples. A statistical discrimination technique is used to produce a scheme for the prediction of performance groups, each of which covers a limited range of cutting rate and/or tool consumption rate.

Jan 1, 1984

By A. L. Holley

THE occurrence of this gas, in quite appreciable. quantities, has been observed for many years in its escape along the creeks of Western Pennsylvania, and more recently, in much larger quantities, from the oil wells in and near Venango County. Within about five years several gas wells have been struck, from which the gas has escaped continuously in prodigious quantities and at great pressure. During the last year a systematic attempt has been made to utilize the flow of gas from one of these wells, and results have been reached which were quite unexpected. This well, near Leechburg, Armstrong County, is about twenty miles northeast of Pittsburgh, on one of the side tributaries of the Alleghany River. It had been drilled in search of oil to a depth of 1250 feet in 1871, but none was found. A great flow of gas was developed, however, accompanied by a slight spray of salt water, and this has continued with little or no diminution to the present time. The gas in its escape has been discharged through a 5-inch pipe, and at a pressure of from 60 to 80 lbs. per square inch, but no exact determinations, either of the pressure or quantity, have been made. The rolling mill of Messrs. Rogers & Burchfield is on the opposite side of the river, and it has been for some years devoted to the production of fine grades of sheet iron from charcoal pig metal, by puddling and in knobbling fires. The usual weekly product of the mill has been 30 tons of No. 30 tin plates, and 50 tons of No. 24 to 28 sheets. The well was bought by this firm for $1000, and the gas is led across the river, a distance of about 500 feet, through a 3-inch pipe. It is distributed through half-inch pipes, and at a pressure of about 45 lbs. per square inch, to several of the furnaces, but a large fraction of the total flow of gas is still wasted at the well. No essential alteration in any of the furnaces has been found necessary in the use of the gas fuel, except to brick up the fire-bridge and to put in the gas and air pipes. The old grate used for coal is loosely covered with bricks and cinder, so that a slight percolation of air may take place through them. The gas is admitted through a half-inch pipe, and blows toward the fire-bridge through 18 or 20 one-eighth inch jets. The air is blown in at about 2 lbs. a

Jan 1, 1876

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

By E. J. McKee

THE area discussed lies south of Canadian River in Hutchinson County, Texas, covering approximately 10 m. east and west and 4 m. north and south. Development is carried on in the manner usual in standard tool operations. No outstanding divergence from the usual methods is necessary as wells are completed in 35 to 55 days to approximately 3000 ft. Most of the time is lost in the upper part of the hole and is usually caused in driving pipe of larger sizes. After approximately 1500 ft., little trouble occurs. A comparison of 13 contractors drilling for Phillips Petroleum Co. gave the following averages: Drilling time from 32 to 63 days with a daily footage of from 49 to 87 ft. per day. The rigs furnished are National turnbuckle type with 6-in. irons and steel wheels.

Jan 11, 1926

By B. Fagerberg, P. H. Fahlstrom

Crushing and grinding practice in Sweden follows closely the international pattern. Certain special circumstances, however, have had an influence on its development. Most mines are worked underground. These mines are either quite small or very large. Sulfide ores are commonly treated by custom milling and, apart from the cement industry, the rock species treated are hard and abrasive. Another important factor is the increasingly strict requirements placed on the mechanical condition of different products, especially lump ores and coarse iron-ore concentrates. Increasing requirements are being placed on the concentrate grade to suit the new steel processes. As a result, iron ore beneficiation has expanded considerably for the production of fine pelletizing concentrates. This applies especially to magnetite ores in the intermediate phosphorus range 0.1-1% P. In 1969, about 5.5 million tons of pellets will be manufactured. It should be pointed out, however, that fairly large quantities of coarse products are still being made at mills where the right conditions are available. Crushing and grinding is also of great importance in the production of rich concentrates at high recovery from sulfide ores. In fact, a large part of the development work on the concentration of sulfide ores has been devoted to the crushing and grinding processes. Boliden has played an important role in this connection.

Jan 10, 1969

By H. Ries

IN THE marketing of mineral products, it is always highly desirable for both the producer and the consumer to be able to discuss things in a common language, and this can only be done if there are standard methods for expressing the properties of the raw materials. Having developed such a form of expression, the next step would be the making of specifications, which may serve as a basis for selecting raw materials. Considering the large number of non-metallic minerals that are used, there are not a few for which there are no standard laboratory tests to be used in determining their properties, or even standard specifications on which grades or market price may be based. Indeed in many cases the consumer simply requests the producer to submit samples, and rejects or accepts them without any explanation. Could the producer know in advance just what the consumer needed, time and money might often be saved. It appears to the writer that it is of the highest importance to devise standard laboratory tests wherever possible, as this enables the consumer to state definitely what he needs, and is of great assistance to the producer. It should also work to reduce misunderstandings and disputes. 'In the case of sands, we find that they show a wide variation in their character, ranging from those that are so coarse as to be of gravelly nature to those that are so fine that they might be classed as silt; and from very clayey ones to those that are practically free from clay. For this wide range of sands, we have a corresponding variety of uses, which are based mainly on the physical properties of the sand, although these are not always very definitely stated. The chemical composition need rarely be considered, if the sand is of siliceous nature. To determine and express these properties there should be standard tests, which are to be followed in all cases where the material is tested in the laboratory.

Jan 1, 1926

By L. E. Mannion

Sodium carbonate or soda ash is one of the two principal alkalis of commerce, the other being sodium hydroxide. The use of sodium carbonate is recorded in ancient Egypt, where naturally occurring brines or solid salts were the source of impure soda for glass manufacture. In early modern times until the 19th century, soda ash, as well as potash, was recovered mainly by leaching the ashes of plants. In Europe, during the 18th century, a brown lye for laundering was produced by pouring hot water over burned seaweed. One of the better grades of this kind of material was a product from Spain termed "barilla," which analyzed 24 to 30% Na2CO3 (Hou, 1942). The birth of the modern chemical industry may be said to start with the LeBlanc process for making sodium carbonate from salt, sulfuric acid, and lime. Although invented in France in 1691, England made the most extensive use of it. In 1863 Ernst Solvay devised the ammonia-soda or Solvay process, and by 1874 the first of many Solvay plants was built. These were to supplant the LeBlanc method and dominate soda-ash production until the present time. Although of lesser importance, natural sodium carbonate deposits continued to support operations in various parts of the world. Shortages during World War II stimulated production of "natural" soda ash, particularly at Searles Lake, Calif., and at Lake Magadi, Kenya. Within the last ten years in the United States, a notable surge in production has occurred based on the vast trona deposits in Wyoming. Table 1 lists some principal producers of natural soda ash and the character of the source deposits. Uses and Specifications Sodium carbonate (Na2CO3) is a white, crystalline hygroscopic powder, an aqueous solution of which is strongly alkaline. Most commercial soda ash is a product that must meet high standards of purity and uniformity. Two forms are commonly sold: a fine, powdery material called light ash, and a more coarsely crystalline dense ash; these weigh 32 to 39 and 60 to 66 lb per cu ft, respectively. Dense ash may be produced by adding a little calcium chloride to the sodium carbonate solution to control crystal size and prevent agglomeration. Specifications and typical analyses of light and dense ash in the United States are shown in [Table 2]. Sizing generally achieves about 75% of light ash and 90% of dense ash between +30 and -100 U.S. screen mesh. World use of sodium carbonate now exceeds 24 million tpy, of which the United States produces more than 7 million tons. The market for soda ash is dominated by the glass industry, which uses almost half the supply. Inorganic chemicals, including phosphates and silicates, consume about 30%. Other principal uses include the manufacture of soaps and detergents, petroleum, caustic soda, organic chemicals, and paper; and nonferrous and ferrous metallurgy. [Fig. 1] shows the percent consumption by use of soda ash in Europe, Japan, and the United States. The price of soda ash in the United States remained relatively stable during the 1960s at about $33 per ton; in 1972 it reached $35 per ton. The price in 1975 was $42 per ton. Geology Mineralogy [Table 3] is a list of the more common sodium carbonate-bearing minerals. Anhydrous sodium carbonate is almost never found in nature; only natron, thermonatrite, and trona have been used directly as sources of sodium carbonate. At Searles Lake, burkeite and hanksite are important in the reconstitution of

Jan 1, 1975

By T. Egleston

During the last winter we have been actively engaged in the School of Mines in search for boracic acid. This has been owing to the fact that Mr. M. W. Iles, assistant in the qualitative laboratory, has discovered a test for that substance which makes its discovery exceedingly simple instead of being, as previously, very difficult. It consists in powdering the mineral, calcining it, then moistening it with sulphuric acid, and heating on a platinum wire until the sulphuric acid is expelled. It is then moistened with glycerin and made to take fire. If boracic acid is present it infallibly gives a green flame. It is not at all surprising, under such circumstances, the test being so easy, that boracic acid has been found by the students in a great many cases where its presence was not previously suspected, and in some where its detection was previously too difficult to warrant looking for it. We were not prepared, however, for its discovery in Lake Superior iron ores, and were disposed at first to think that a mistake had been made. After, however, it had been frequently reported in these ores it was considered worth while

By K. T. Aust

It is proposed that the intergranular corrosion of austenitic stainless steels is associated with the presence of continuous grain houndary paths of either second phase, or solute segregate resulting from solute-vacancy interactions. Experimental observations of structural changes and crrosion behavior of different types of austenitic stainless steel provide support for this poposal. On the basis of this model, it is shown that the intergranular -corrosion susceptibility of austenitic stainless steels in nitric-dic hromate solution may be substantially reduced either by suitable heat treatments or by impurity control. AUSTENITIC stainless steels, such as Type 304, generally have excellent corrosion resistant properties when properly solution heat-treated and used at temperatures where carbide precipitation is slow. However, several corrosion environments have been found which produce intergranular corrosion of solu-tion-treated stainless steels, that is, those steels with no detectable carbide precipitation.''2 Of the various corrosion environments, the most widely used test solution has been the boiling nitric-dichromate solution. In these acid solutions, stainless steels have been found to be susceptible to intergranular attack despite the addition of carbide-forming elements such as titanium or columbium, or despite lowering of the carbon content or use of high-temperature solution treatments. Studies of the electrochemical mechanism of corrosion attack have been made by several worke1s3'4 who found that oxidizing ions such as crt6 depolarize the cathodic reactions and consequently raise the open-circuit potential of stainless steel immersed in nitric acids. As a result of this, the anodic reaction is accelerated. The reason for the localization of anodic activity at the grain boundaries, and resulting intergranular corrosion, has not been conclusively determined. Several workers, e.g., Streicher,3 and Coriou et al.,4 have suggested that the strain energy associated with grain boundaries provides the driving force for the accelerated intergranular corrosion. This argument would predict that alloys of high purity would still be susceptible to intergranular attack. However, work by chaudron5 and by ArmijO,6 has shown that high-purity alloys are immune to attack, in disagreement with this argument. An alternative suggestion is that chemical concentration differences exist between grains and grain boundaries, that is, impurity segregation at boundaries, and that these chemical differences provide the driving force for localized attack. It is this impurity segregation which can lead to accelerated dissolution of grain boundaries when the alloy is exposed to a suitable corrodant. This mechanism would predict the immunity of high-purity alloys to inter-granular attack, which is in agreement with experi-mental observations. In the present paper, some recent studies on inter-granular corrosion of austenitic stainless steels which were conducted by coworkers and myself will be re-tibility A simple model will be described in which it is proposed that the intergranular corrosion of aus-tenitic stainless steel is associated with the presence of continuous grain boundary paths of either second phase or solute-segregated regions.* On the basis of this model, it is suggested that the intergranular corrosion rate can be markedly reduced by the formation of a discontinuous second phase at the grain boundaries if the discontinuous second phase incorporates the major part of the segregating solute, drained from the grain boundary region. Results are presented of corrosion tests and electron microscopic studies of different types of austenitic stainless steel after various heat treatments which provide experimental support for this model. Finally, a solute clustering mechanism, based on a solute-vacancy interaction, is shown to be consistent with the results obtained for inter-granular corrosion of solution-treated austenitic stainless steels. EXPERIMENTAL Corrosion tests using weight loss measurements were made on sheet specimens, which were lightly electropolished, washed, and immersed in boiling (115°C) 5 N HN03 containing 4 g crt+6 per liter added as potassium dichromate. Studies in which the inter-granular penetration depth was measured both by electrical resistance and metallographic methods have shown an empirical correlation between the rate of intergranular penetration and the weight loss per unit time for identically treated specimens of stainless steel." As a result, although all the corrosion data reported here are in terms of simple weight loss measurements, these data are considered to reflect primarily the rate of intergranular dissolution. Fig. 1 shows a typical result of intergranular attack of a solution-treated Type 304 stainless steel after 4 hr in a boiling nitric-dichromate solution. The wide grain boundary grooving at the surface, and the attack at incoherent twin boundaries, are evident; very little corrosion attack is seen at the coherent twin boundaries. INTERGRANULAR CORROSION MODEL

Jan 1, 1970

By E. H. Roberts, L. G. Swenson, F. C. Nix, R. A. Morgen

THE binary system lead-antimony has been the subject of comprehensive investigations in these laboratories by Dean' and his associates. The effect of a third constituent on this system, particularly on the lead-rich alloys in which dispersion hardening was found, has a commercial value as well as an academic interest. This paper covers the effect of the addition of copper, bismuth and tin, all of which are likely to be found in commercial lead-antimony alloys, and is divided into three parts, as follows: I. The System Lead-Antimony-Copper II. The System Lead-Antimony-Bismuth III. The Lead Corner of the System Lead-Antimony-Tin These three systems are of three different types, and hence may be considered as covering three general kinds of additions. Bismuth forms no compounds with either lead or antimony and forms solid solutions with both. Copper forms several compounds with antimony as well as solid solutions but with lead it forms a two liquid layer system and no appreciable solid solution. Tin is soluble in both lead and antimony in the solid state and also forms a compound with antimony. The effect of small amounts of bismuth on the lead-antimony alloys is small, having no appreciable effect on the solubility of antimony. The temperature of the solidus floor is lowered appreciably by the presence of bismuth, cutting down the range of heat treatment. Copper, on the other hand, due to compound formation, increases the apparent solubility of antimony. The excess antimony is tied up with the copper finally and so is not available for dispersion hardening. The net result of addition of small amounts of copper is to shift the dispersion hardening peak of the

Jan 1, 1928

Jan 1, 1964

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By Hugh H. Waesche

AN adequate supply of crystalline quartz of piezoelectric grade and size continues to be of fundamental importance to the U. S. Army Signal Corps. Current electronic development programs of the Armed Forces depend upon the use of quartz crystals in all applications where accurate frequency control is necessary. In peacetime this&apos; may not seem too significant, but in planning for possible national defense emergencies, an adequate supply of piezoelectric grade raw quartz is just as important as an adequate supply of some of the more publicized strategic minerals. Prior to World War II, the Signal Corps accepted the use of quartz crystals for frequency-control purposes in essentially all electronic communication, navigation, and radar equipment operating in the audio and radio frequency spectra up to and including the ultra-high-frequency channels. Over 4,000; 000 lb of radio-grade quartz was required between January 1942 and V.J Day. Use of such a large quantity of crystal units was necessary in order to establish and maintain, with a minimum of effort, clear and definite frequency channels of greater stability than could be obtained by any other means. This policy was justified on the basis that quartz was without a peer as a frequency-controlling element. Military and civilian uses of quartz in the field, as well as laboratory studies, have confirmed this premise and no means of highly stable frequency control, superior to quartz, has been discovered. It appears certain that the demand for use of quartz for frequency control purposes will continue at a high level.

Jan 1, 1948

By T. D. Yensen, R. K. McGeary

While we have not been primarily interested in the determination of hydrogen in the alloys that we have been dealing with, we arc very glad to cooperate in this symposium on sampling and analysis for hydrogen, as we can never tell when we may find it desirable to perform such analyses. Vacuum-fusion Method Our primary interest has been oxygen and carbon, in the analysis of which we think we have become very proficient. Our oxygen-analyzing apparatus is of the vacuum-fusion type (Fig. I). This employs Dr. Derge&apos;s type of graphite cruciblc and slit sleeve, with graphite powder between, for heat insulation (Fig. 2) supported in a clear quartz bulb connected to the Pyrex glass system by means of a carefully made ground joint. The latter is kept cool by means of an air blast from a circular copper tube surrounding the joint. The crucible is heated by high-frequency induction and the 24 one-gram samples successively dropped in from the horizontal tube at the top by means of a magnet. The gases (H², CO, N2) are passed through the CuO catalyst held at 300°C. (converting CO to CO²I, H² to H²O) and the CO² and H2O frozen out in the main liquid air trap, while N2 is evacuated. At the end of the operation, shown by the termocouple vacuum gauge indicating a pressure of 10-4 mm. Hg, the analyzing system is isolated by means of the mercury cutoffs, and the CO² and H2oare determined by transferring first the CO2 and then the HzO to the small trap at the right. This is done by placing liquid air on the small trap, then removing the liquid air from the large trap for one minute, which is sufficient to evaporate the Co2 and transfer it to the small trap. The CO2 is then measured by closing the mercury cutoff at the extreme right, removing the liquid air from the small trap, warming it up to room temperature, adjusting the mercury level to one of the three marks on the glass tube (corresponding to three volumes calibrated so that I mm. Hg of CO² corresponds to 0.001, 0.002 and 0.010 mg., respectively, of oxygen) and finally reading the pressure. Liquid air is now replaced on the large trap, the mercury cutoff at the right opened, transferring the COz back to the large trap. The cutoff to the pumps is then opened, the liquid air removed for one minute, thus evacuating the CO², the pumps again cut off and the H2 O transferred to the small trap as before, except that it is now necessary to warm the large trap with a Bunsen burner in order to evaporate all the H2O. This requires about three minutes, as the inner tube must be heated to at least 100°C. In order to prevent H²O from being adsorbed on the glass walls, the glass tubing beyond the catalyst (i.e., to the right in Figs. I and 3) is kept heated to about 150°C. by means of Nichrome ribbon as shown in Fig. 3. For a I-gram sample the above amounts of oxygen (0.001, 0.002 and 0.010 mg.) 35

Jan 1, 1945

By Edward Estabrook

THIS paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: BARRELS BARRELS 1915 94,073.5 1918 2,946,774.27 1916 1,404,183.97 1919 2,000,584.84 1917 2,780,697.51 1920 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field.

Jan 2, 1922

By Albert Sauveur

Iron, like other metals, solidifies through the formation of dendritic crystals; iron alloys forming solid solutions, like other solid solutions, solidify likewise through the formation of dendritic crystals. The alloying elements or impurities as well as the inclusions segregate generally in the interstices, or "fillings," between the axes and branches of the dendrites; that is, in the portions last to solidify. This results in dendritic segregation or heterogeneity, which is generally persistent and makes possible the revelation of the dendritic crystallization of the metal through the selective action of a suitable etching reagent.&apos; For this purpose, a cuprie solution, such as Le Chatelier&apos;s, is generally used, copper being deposited on the pure, or relatively pure, ferrite present in the axes while the fillings remain free, or relatively free, from copper deposition. The dendritic structure, formed on solidification in a steel containing 0.50 per cent. carbon, 0.37 per cent. manganese, 0.12 per cent. silicon, 0.07 per cent. sulfur, and 0.035 per cent. phosphorus is shown, after treatment with Le Chatelier reagent, in Fig. 1 under a magnification of 8 diameters. Commercial steel always contains inclusions of manganese sulfide, which are located in the fillings of the dendrites. Comstock has shown that boiling sodium picrate imparts a dark coloration to these inclusions. We find that this reagent likewise reveals dendritic segregations in commercial steel, as shown in Fig. 2, under a magnification of 8 diameters. which represents the same spot as that shown in Fig. 1. The fillings have been darkened while the axes remain white, the action being, therefore, the reverse of that of cupric reagents. On closer examination, under higher magnification (Fig. 3) it is found that the picrate blackens the small particles of manganese sulfide, that these are frequently surrounded by a rim of white, or relatively white, ferrite, and that both the ferrite

Jan 1, 1924

THE Searles Lake orebody is located in the north- west corner of San Bernardino County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which differ in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor.

Jan 2, 1954

By Arthur F. Wendt

Within the last few years the production of iron, and of the metals generally, by a given furnace-plant, has been largely increased, in many instances trebled. Iron-furnaces exceeding one hundred tons&apos; capacity per diem are now the rule in new constructions. Copper and lead-furnaces smelting from 60 to 100 tons of ore per day are common. With this greatly augmented product, the life of furnace-linings has been diminished, and recourse has been had to various cooling devices for prolonging the life of such liuings. The object of this paper is to call the attention of the profession to an arrangement recently patented by the writer. The common course of projecting water against the exterior of the brickwork of a furnace has been in a large measure abandoned by our most progressive managers. All have recognized the danger of this proceeding, especially when applied to the crucible of a furnace below the line of the tuyeres. Cast-iron water-jackets, with wroughtiron pipes for circulating the cooling-water, have replaced the cruder methods. In iron-smelting the use of such jackets has been confined to the crucible and the space around the tuyeres; and it has been the custom to support the jackets on the brickwork of the furnace. But the erosion of the brickwork below tuyere-jackets allows them to sag, and often displaces the alignment of the tuyeres and leads to other annoyances. The principle of construction adopted by the writer to remedy this and other evils, is to use a thin fire-brick lining (not over nine inches) from the tuyeres up to the bosh, to back this lining with wrought-iron or steel water-jackets, hung from the mantel-ring, and thus to carry the whole weight of the furnace and its filling upon the supporting pillars. The crucible proper is lined with three or four thicknesses of fire-brick on the sides, and not less than forty-eight inches in the bottom. It is supported on independent pillars, and is practically an independent structure. It could even be placed on wheels and made removable, were there any adequate advantage to be gained by such an arrangement.

Jan 1, 1885