Search Documents

By Sylvan Cromer

THE need for a clear understanding of the physical nature of the flow of gas-liquid mixtures in vertical pipes is ever becoming more apparent. This type of flow is encountered when gas and oil are produced from a well; when water is removed from gas wells with siphon lines and when liquids are elevated by means of air or gas lift. Although a number of investi-gators1-7 have published data on the flow of gas-liquid mixtures, in only a few cases has the experimental setup been devised to permit visual study. In the fields of heat transmission, such as the boiling of liquids and the study of the critical phenomena of the hydrocarbons, researchers have been able to throw additional light on heretofore unexplainable happen-ings through actual observation in glass apparatus. This investigation was therefore undertaken in order to obtain qualitative as well as quanti-tative results for air-water flow. EXPERIMENTAL APPARATUS AND PROCEDURE The flow column used in these tests was made of standard 2-in. pipe and was approximately 98 ft. in height. Pyrex observation sections 2 ft. long having the same internal diameter as the wrought-iron pipe were placed at 14-ft. intervals in the column. The bottom of the tube was cut off square and terminated in the mixing chamber. No perforated nipple or footpiece of any kind was used. To the top of the column was fastened a semicircular return bend having a 4-ft. radius. The flow column was supported by a standard cable-tool drilling derrick (Fig. 1) into which were built observation platforms at each Pyrex section.

Jan 1, 1939

By Charles Seastone

Location THE hydro-electric plant of the Peninsular Power Co., is located at what is commonly known as Lower Twin Falls on the Menominee River. This location is about 33 miles north of the city of Iron Mountain, Mich. The principal points of delivery of electric energy from this plant are in the mining regions adjacent to Florence, Wis., and Iron River, Mich., and in the cities of Iron River and Iron Mountain. The hydro-electric plant at Twin Falls and the substation of the Iron Mountain Electric Light & Power Co. are connected by a 6,600-volt transmission line carried on steel towers and steel poles, the latter being used within the city limits. The plant at Twin Falls and the substation at Iron River, about 36 miles distant, are connected by a 66,000-volt, duplicate, three-phase transmission line, supported on steel towers. At Iron River, are located a 1,500-kw. auxiliary steam plant, and the substation, from which the current is distributed to the mines in this vicinity. A description of the auxiliary plant, main and customers' substations, and of the main and secondary transmission lines, follows later in this paper.

Jan 2, 1915

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions' has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow' realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.' Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.' Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington'" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By R. H. Olds, B. H. Sage

The transient flow of gases in long pipe lines is a problem of industrial interest. The present discussion deals with the application of the conservation of momentum and material to the transient flow of gas in conduits which are long with respect to their diameter. Solutions of the resulting equations include consideration of variations in friction and specific volume of the fluid as functions of time and position along the conduit. The changes in state along the pipe line are established as a function of time. The methods proposed may be extended to other situations. The flow of compressible fluids under steady conditions' has been considered in detail. Primary emphasis was placed on the development of simple means of taking into account the non-uniform flow' realized in long conduits under such conditions. Binder2 discussed the essential differences between the flow of compressible and uoncompressible fluids. Bonilla" proposed direct methods of solution for equations describing isothermal flow in long pipes. Similar considerations limited to steady flow have been discussed by Ruth.' Palsgrove 5 sugrested a graphical means of solving specific problems relating to the flow of gases in conduits of uniform section. Some of the basic concepts of the flow of a compressible viscous fluid in straight tubes have been described by Kuo.6 Problems of this type require knowledge of the equation of state of the fluid. In many cases it liar been convenient to assume that the fluid follows the relationship ascribed to a perfect gas. The treatment of unsteady flow of compressible fluids is less complete. This state of affairs result* from the fact that the differential equations relating pressure and flow rate with time and position for unsteady flow are nonlinear in character.' Muskat and Wyckoff presented an excellent treatment of the situation in laminar Bow where inertia forces were not of controlling importance. Somewhat earlier Hurst9 discussed the uncteady flow of fluids in petroleum reservoirs. Helhering-ton. MarRoberts. and Huntington'" established experimentally the pressure distribution and accumulative flow rate of natural gas through an unconsolidated sand. Recently Joffe11,12 conhitlcretl the specific problem of the flow of natural gas in relatively long.,. pipe lines for unsteady conditions with emphasis upon the economic feusibility of the storage of gas in such a reservoir. These discussions were based upon approximations of the partial differential equations applying to the condititons of flow. The results were descriptive of the physical situation and indirated the effertiveness of large pipe lines as cyclic storage facilities for natural gas. The advent of analog computers" has increased materially the practicality of solving nonlinear partial differential expressions. Several iterative numerical and graphical methods14,15,16 have been developed to solve nonlinear equations. However, it appears that the pair of simultaneous nonlinear partial differential equations involved in problems of this nature are not directly susceptible to solution by presently available analog computer or formal iterative numerical techniques. Nevertheless. graphical analyses afford a means of obtaining data of engineering value without special equipment. MATHEMATICAL CONSIDERATIONS Since the length of the conduit is large in comparison to the cross section in the cases to be considered, it is possible to treat the characteristics of the flow as independent of position in the cross section of the conduit. This possibility follows since the energy- connected with the velocity profile is small compared to that required to overcome the friction associated with its movement throughout the length of the line. Average values of the pressure. velocity. kinetic energy. momentum, and specific volume may he assigned to the fluid at any particular cross section. From a mathematical viewpoint this may be expressed in the following way for velocity: µ = µ(?X)..........(1) The uncertainties introduced by such assumptions usually are negligible when the ratio of length to diameter is greater than the order of 1.000. On this basis a volume element ma!. be considered to occupy the entire cross section of the conduit. Such an element is presented in Fig. 1.

Jan 1, 1951

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By A. K. Mukherjee, J. E. Dorn, J. D. Mole

Investigations were carried out on the effect of polyslip on the strain hardening of aluminum single crystals. The orientations investigated were those lor which the tensile axis was in the [001], [111], [112], and [012] directions plus another for which the Schmid angles for {111}(110) slip were 1 deg. The experimental data were analyzed on a model based on the intersection of dislocations with particular emphasis on the effect of polyslip on the activation volume for inter-section. It is shown that the rate of strain hardening inreases for those orientations wherein attractive dislocation intersections occur and that those orientations which produce the greater number of such intersections exhibit the greater strain hardening. Good correlation of the data is obtained with the concept that attractive junctions, as proposed by Saada, Play an important role in accounting for the rate of strain hardening. EXISTING concepts on the nature and cause of strain hardening in fcc metals have been deduced principally from experiments on the deformation of single crystals under single slip. The effect of crystal orientation on the shapes of the stress-strain curves for single slip have been summarized by seegerl and more recently by Clarebrough and Hargreaves.2 Tensile specimens whose axes fall near the center of the [001]-[011] line of the standard triangle of the stereographic projection exhibit the longest range of easy glide (Stage I) and the lowest rates of linear hardening (Stage 11) whereas specimens whose axes lie near fie [001]-[111] line of the standard triangle have limited or no easy-glide range and exhibit somewhat higher linear strain-hardening rates. Specimens whose axes lie near the [001] or the [ill] poles do not exhibit easy glide and have the highest rates of linear hardening. Kocks3 has shown that the highest rates of linear hardening Occur under Polyslip when the tensile axis coincides with the [111] or the [ 001] pole. Since the rate of strain hardening is sensitive to specimen orientation and the incidence of polyslip, these relationships might help to discriminate between various dislocation models for strain hardening in fcc metals. Previous attempts to analyze the effect of orientation on strain hardening,1"3 however, did not provide a unique answer to this problem. Consequently the present investigation was undertaken wherein additional data, particularly that for the effect of polyslip on the activation volume for intersection, was also determined in order to provide more complete information on the details of strain hardening. Whereas analyses of these data reveal that several recommended models for strain hardening are at variance with the facts, good correlation of the data is obtained with the concept that attractive junctions4 play an important role in accounting for the rate of strain hardening. I) EXPERIMENTAL APPROACH seegerl demonstrated that slip in fcc crystals at low temperatures is dependent on thermally activated intersection of glide dislocations with forest dislocations. This has been confirmed by tests on single crystals of aluminum by Mitra, Osborne and Dorn5 and on polycrystalline aluminum by Mitra and Darn.' Thus in accord with Seeger's theory, the shear strain rate, ?, below a critical temperature, T, is where .V is the number of points of contact per unit volume between forest dislocations and glide dislocations, A is the area swept out per successful intersection, b is the Burgers vector, v is the frequency of vibration of the segment of the glide dislocation undertaking intersection, U is the activation energy for intersection, k is Boltzmann's constant, and T is the absolute temperature. For aluminum, which has an extremely high staeking-fault energy, the constriction energy is negligibly small and therefore the activation energy decreases practically linearly with the stress according to as will be recomfirmed later, where Uo is jog energy at the absolute zero, G and Go are the shear moduli at the test temperature T and O°K, respectively, L is the spacing of the forest dislocations, t is the applied shear stress for slip, and tGo is the stress field that must be surmounted athermally.

Jan 1, 1965

By Mark J. Klein, A. H. Clauer

The Snoek peak induced by solute nitrogen in chromium was studied. A rapid quenching rate is required to maintain nitvogen in solution in sufficient concentrations to be detectable by internal-friction techniques. An expression for the tertninal solubility, c, of nitrogen in weight pevcent is log,,c = -4130/T + 1.05. The diffusion of nitrogen in zhromium determined by internal friction is SNOEK&apos;S theory1 of the stress-induced ordering of interstitial solute elements in the bcc lattice has been used to deduce information on the behavior of interstitials in a number of bcc metals. Under the proper conditions, internal-friction studies of "Snoek peaks" permit a determination of diffu-sivities, solubilities, and precipitation kinetics of interstitial elements. Internal-friction studies of this type have been reviewed by Nowick,&apos; Wert,= Powers and Doyle,4 and others. The behavior of interstitial atoms in Group V-A metals and iron has been rather extensively studied in this way, and results are reasonably self-consistent. However, the study of interstitial elements using internal friction in the Group VI-A metals—tungsten, molybdenum, and chromium—is much less clear. Thus far, internal-friction studies have revealed a peak in tungsten tentatively attributed to carbon5 and a peak in chromium associated with nitrogen. In chromium, Bungardt and Preisendanz6 observed a peak at 180°C for a frequency of -1 cps which they associated with nitrogen. More recently, de Morton7 determined the diffusivity of nitrogen in chromium from studies of a nitrogen peak at 160°c for a frequency of -1 cps and from elastic aftereffect measurements. The objective of this investigation was to study the nitrogen peak in greater detail, to obtain information on the behavior of nitrogen in chromium. This information is of interest because nitrogen is known to have an embrittling effect on chromium. However, efforts to deduce the role played by nitrogen in influencing the mechanical behavior of chromium are handicapped by lack of information on its behavior and distribution in chromium. EXPERIMENTAL PROCEDURES The chromium wires used in these studies were drawn from arc-melted iodide-chromium stock that had been extruded, swaged, and centerless-ground to 0.25 in.-diameter rods. Internal-friction measurements were made in an evacuated torsional pendulum similar to the one described by Kê,8 utilizing wires 0.048 to 0.030 in. in diameter. A series of analyses of the fabricated wires showed that the major impurities were approximately 100 ppm Fe and a combined interstitial content of 50 to 100 ppm C, O, N, and H. A typical interstitial analysis of the wires after processing is 15 ppm C, 2 ppm H, 50 ppm O, and < 5 ppm N. Interstitial concentrations were determined by vacuum-fusion, combustion-conductimetric, and micro-Kjeldahl analyses. In general, vacuum-fusion analysis yielded a lower nitrogen concentration than did micro-Kjeldahl analysis. For consistency, the nitrogen concentrations reported in this investigation were determined by the former method. Heat treatments were carried out by encapsulating the specimens in quartz tubes containing argon. The fabricated wires were annealed at 1150°C for 1 hr to produce uniform recrystallized grain size of about 0.015 mm. Nitrogen and carbon were added to the fabricated wires by encapsulating them in a quartz tube containing ammonia or methane, and annealing them at 1150°C for 48 hr. In some instances, carbon was also introduced by coating the wires with carbon black prior to annealing.

Jan 1, 1965

By Robert D. Pike

IN November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: [ ] Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2,3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depend¬ing upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1947

By T. C. M. Pillay, John Chipman

The Si-0 equilibrium in liquid iron was investigated in some detail by Gokcen and Chipman1 who reported equilibrium constants of the following reactions: In each case the thermodynamic equilibrium constant K was obtained by extrapolating K&apos; to infinite dilution. Their results on reaction [I] were consistent with those of earlier observers, and there seems to be little doubt as to the approximate validity of the equilibrium product determined. On the other hand, the results on reactions [2] and [3] indicated unusual curvilinear relationships between the activity coefficients of silicon and of oxygen and the silicon concentration. Since a linear relation is observed in all other similar instances, it was concluded that some source of error had affected the gas-metal equilibrium relationships. Recently the authors undertook a restudy of these equilibria with the view especially to establishing the equilibrium constant of reaction [2]. Their experiments, however, were discontinued before a tbroughly satisfactory answer had been obtained and consequently have remained unpublished until the present time. Quite recently Matoba, Gunji, and Kuwana2 published the results of a very thorough study of these equilibria. It is the purpose of the present note to Compare these three sets of experimental data, a comparison which leads to Confirmation of the results of Matoba and coworkers. The experimental arrangements described by Dutilloy and Chipman were employed. A controlled mixture of Hz, H,0, and argon was led into the induction furnace over the surface of the Fe-Si melt contained in a silica crucible. On account of the slow approach to equilibrium, runs were continued for at least 8 hr and, in some cases, as much as 12 hr. Samples were taken by means of silica tubes at the start and during the final 4-hr period of each run. Out of twelve runs only seven appeared to have approached equilibrium with sufficient certainty to be reported here. The results of these experiments, all at 1600°c, are shown by the triangles in Fig. 1. Equilibrium was approached from both oxidizing and reducing conditions and the direction of approach is indicated by the shape of the triangle. Attempts to extend the study to higher silicon concentrations were unsuccessful on account of the transfer of silica from the metal bath to the upper portions of the crucible by means of a silicon-monoxide mechanism. Matoba, Gunji, and Kuwana used similar methods and approached equilibrium from both sides. Their results at three temperatures are shown by the solid lines of Fig. 1. A line corresponding to 1600 deg is interpolated from their equations and is shown by the dotted line. The results of Gokcen and Chipman at 1600 deg in the range 0.02 to 2.0 pct Si are also shown. At concentrations up to about 0.6 pct Si, these investigators approached equilibrium from both directions, and their results in this range appear to be trustworthy. Above 1 pct Si, however, all of their experiments involved oxidation only, as shown by a decrease in the silicon content of the bath. It now seems certain that they failed to reach equilibrium at these higher silicon concentrations and that the curvilinear relation shown by their results is incorrect. It is evident that their results in the lower silicon range are in good agreement with those of Matoba and coworkers. In fact, a straight line drawn through their results would parallel the dotted line and would differ from it by only 0.05 in log K. The new data also lie close to that line. It may thus be concluded that the three sets of data are in good agreement and that the equations proposed by Matoba and coworkers for reaction [2] are satisfactory . They take the limiting value of log K&apos;, at 0 pct Si as log K ,. The slope of each line gives the value

Jan 1, 1962

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark&apos; at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark&apos;s experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

By Eugene A. Stephenson, Leon J. Pepperberg

The natural gas industry is essentially a byproduct of the oil industry. When first discovered the gas was usually regarded as a nuisance, and even when found immediately associated with oil, or suspected to be so, it was customary to blow it freely into the air, in the hope that gas would shortly be replaced by a flow of oil. The early methods of production,&apos; transportation, and utilization were neither economical nor efficient; the chief value of gas was based on its use as a fuel, with no regard to (1) its effect. upon the oil with which it was associated, (2) its importance as a lifting agent, or (3) to its possibilities for the manufacture of byproducts. The spread of scientific research among major gas and oil companies, manufacturers, and academic groups, has gradually brought recognition of the fact that many of the technical problems bearing on production, transportation and utilization are common to both the gas and the oil industry. A few of the problems that have received serious study, and from which highly gratifying results have been obtained, are: (1) gas measurement, (2) oil well and gas well capacity tests, (3) elimination of field waste, (4) design of pipe lines and compressor stations, (5) extraction of constituents which might interfere with the normal flow of gas through the line, (6) control of reservoir pressure, (7) estimation of reserves of both oil and gas, (8) control of water encroachment, (9) measurement of factors which influence fluid movement through sands, (10) solubility of gases in oils, (11) effect of dissolved gases upon the properties of the solution. These investigations have demonstrated that almost every problem relating to oil production also involves some phase of natural gas engineering. During the past 15 years the use of experimental methods for the discovery and measurement of obscure, influencing factors, which cannot be determined purely by hydrodynamic or thermodynamic analyses, have contributed much towards the progress made in solving the problems of the oil and gas industries. Most of the experimental work on

Jan 1, 1934

NEW, MEMBERS The following list comprises the names of those persons who became members during the period July 10, 1916; to July 31, 1916: BOYD, ROBERT RUSSELL Supt:,-Arizona -Commercial Min Co., Globe, .Ariz. BRADLEY, HENRY FRANKLIN, Chem, American Smelt & Ref. Co. Murray,:Utah: BROWN, THOMAS ELLIS, JR..:&apos;. L .:.::..55 Hill, St;; Morristown, N. J. CARY, WEBSTER P., Expert Operator,-General Engineering. Co:, Salt Lake City, Utah. CLARK, ALONZO WEBSTER 3223_ Scottwood Ave., Toledo, Ohio. CORP, CLIFFORD Old Dominion Copper Min. & Smelt. 60., Globe, Ariz. CROMBIE, W. RANSOM, Min. Engr Detroit Copper Min. Co., Morenci, Ariz. DELANEY, EUGENE A., Chief Engr., Berwind-White. Coal Mining -Co., Windber, Pa ELBELT, WILLIAM HENRY, Dept. Foreman., Chino Copper Co., Hurley, N. Mex. FOSTER, L. JULIO, Mgr., Minas i Fundicion ; ?La Junta," San Bernardo, Chile, South America. GASKILL, JAMES PHILLIPS, Genl. Mgr.,.Ajo Cons. Copper Co., Ajo, Ariz., via Gila, Ariz. .

Jan 9, 1916

By S. C. Langdon, Henry S. Rawdon

The following note describing the behavior of copper under rather unusual conditions is offered for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning, as well as softening it. It is well known that metals may be rendered very brittle by electrolytic action in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear 2 similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. TO demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 801" C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for several minutes. When removed from the bath, cooled, and tested for brittleness by bending the specimen back and forth, while clamped firmly at one end in a vise, the copper rod was found to be very brittle, as compared with a rod of the same length of the untreated copper tested

Jan 1, 1921

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the &apos;classification of coals according to rank and quality of grade.&apos; The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By H. Evans, L. A. Hunt

In the pellet-producing industry it is sometimes claimed that "The pellets are made in the concentrator," or that "The key to good pellets is in the balling operation." However, one claim is generally agreed on: If you can put in, on, and through the indurating furnace a good green ball of Proper size and adequate strength to withstand the handling, load, dehydration, and thermal shock until it is properly heat-hardened, you will have the pellet product you desire-that is, a "competent" green ball. The strength requirements that enable a competent green ball to withstand the environment of the indurating furnace are usually less restrictive than those for transporting the green ball from its source of production to the furnace. Experience has shown that different types of material may have different balling characteristics which may impose limitations on the quality of the green ball that can easily be produced under normal conditions. Therefore, if a specific material will produce a green ball that meets the physical requirements for competency in the furnace, but not for handling or transportation, various practices must be instituted to overcome this deficiency. In other words, if a normal handling system is too rigorous for the green balls that can be produced under standard conditions, then "handling with care" should be tried.

Jan 5, 1967

By Perry Olcott .

THE Taka oil field is in the northern part of Titus and Franklin Counties, in north- eastern Texas. The small town of Talco, from which the field derives its name, is on the P. & Mt. P. R. R., about 15 mi. north of Mt. Pleasant, the county seat of Titus County. The oil field extends east and west from the town of Talco, the approximate center. In May, 1924, R. L. Cannon, while doing surface geology for the Humble. Oil & Refining Co., mapped the surface trace of this fault structure as evidenced by Upper Midway faulted down against Lower Midway. In the interval of sixteen years between the original surface work and the recent productive well completion, approximately eight wells were drilled into the Woodbine sand without success. The structure was well defined by those tests and all of the wells en-

Jan 1, 1936

By C. E. MacQuigg

BY and large the education of the engineer has been conservative and the reasons for this are obvious. Quite properly it has been a tradition of engineering education that facts and not fancies must be adhered to. Without a doubt, those men who formed the mold of our engineering philosophy as much as it is possible for such molds to be established-rightly held the highest standards of intellectual honesty. Fortunately, it was unthinkable to them to temporize with untried theories and naturally the men whom they trained as engineering educators carry this philosophy in turn to their students, thus handing down the tradition of stability.

Jan 1, 1943

By V. S. Gupt, W. H. Somerton

Rock may undergo great changes in physical properties when heated to high temperatures and then cooled, The temperature and intensity of reactions causing rock alterntiorl.s can he controlled by introducing certain chemicals during heat treament. Three typical outcrop sandsone samples were saturuted with common salt solutions, then heated to several maximum temperatures. After cooling, it was found that per-rrreuhilities had increased much more for salt-saturated samples than for samples not saturated with salt but heated to the same temperatures. This was only true, however. for samples heated above the melting points of the particrrlar salts. Potassium chloritle was particularly effective with Bandera sandstone. Samples saturated with potassium chlorirlr. solution and heated to 900C showed an 11-fold increa.se in perrrieahility. Samples without potasrirdrn chloritle but heated to the .same temperature. showed only a 2.7-jold incresre in permecahility. In application, it seems possible that injecting chemicalc into the formations from a wellbore followed by applying intensive borehole heating might promote reactions which would greatly improve permeability of the formalions. INTRODUCTION Great changes in the physical properties of rocks which have been heated to temperatures in the range of 600 to 800C have been reported earlier. Permeability increases of 50 per cent, and equivalent decreases in sonic velocity and breaking strength have been observed. Although there might be some suppression of certain reactions responsiblc for these changes when rock samples are heated under simulated reservoir pressure conditions. recent work has shown that these are more than offset by the increased importance of other reactions at high pressures. The reactions considered responsible for alteration of rock properties by heating include differential thermal expansion. dehydration, phase changes and dissociation of mineral constituents. Ceramists have long known that temperatures at which reactions occur can be raised or lowered by the presence of certain impurities in the sys. tcnl. Thus the possibility exists that by saturating rocks with appropriate solutions. desired reactions might be accelerated and unwanted reactions might be suppressec! when the rock is heated. Purpose of the present work was to investigate the effects of several common salts on the thermal alteration of sandstones. Types of reactions which might occur are reviewed and the findings of a number of thernlochemical alteration tests are presented. THEKMOCHEMICAL ALTERATION OF SANDSTONE MINERALS The most abundant constituent of most sandstones is quartz. Quartz can exist in at least eight different forms, but in the temperature range of immediate interest (to 900C) only two forms are of importance—alpha quartz below 573C and beta quartz above this temperature. Although the alpha-beta inversion of quartz is very important in thermal alteration of rocks. it is not particularly important here because the inversion temperature cannot be changed significantly by the presence of impurities or by the application of pressure. The transition temperature of quartz to tridynlite is 867C. but the transition is very sluggish. Tridymite is considered to be a metastable transition phase between two stable phases: quartz?cristobalite. However. the transition temperature for tridymite to cristobalite is 1,470C.4 The quartz-tridymite-cristobalite transition can be accelerated substantially by the presence of fluxing agents. Finely divided calcium, magnesium and titanium oxides accelerate the conversion while A12O may retard it. A Mixture of NaCl and CsCl reduces the temperature for cristobalite formation by as much as 420°C. Feldspars constitute the second most important mineral in sandstones. The melting points of feldspars range between 1,000 and 1,700°C depending upon the variety. No information available indicated any important role of fluxing agents in the thermal alteration of this group of minerals. Carbonate minerals are subject to dissociation at temperatures within the range of the present investigation. The dissociation of magnesite can start at a temperature of 373°C, but the reaction is sluggish and might not occur untll a temperature of 500°C or ,higher is reached. Dolomite dissociates in two stages at 500°C and 890°C, whereas calcite dissociation temperature is about 885C. Because CO2 is released in the dissociation of carbonates, ail such reactions are somewhat dependent upon CO2 partial pressure. In the absence of CO: in the surrounding atmosphere, the dissociation of calcite starts at 500°C.However. when 1 atm of CO surrounds the sample, the dissociation does not start until 900C. The other carbonates are apparently much less sensitive to a change in partial pressure of CO2. The aragonite calcite transformation can occur an!. where within the temperature range of 357 to 488°C. depending upon the presence of impurities such as barium. strontium. lead and perhaps zinc. The differential thermal analysis (DTA) curves of both magnesitc and dolomite vary with the presence of &apos;impuritics. The presence of iron in particular seems to affect the magnesitc DTA curve

Jan 1, 1966

By V. O. Struebing, K. A. Johnson, F. H. Ellinger, C. C. Land

The system Pu-Ce-(Pu,Ce)Co2 has been investigated by thermal, micrographic, and X-ray diffraction methods. The principal characteristics of this system were found to be: 1) a "eutectic" valley extending across the phase diagram from the 6 Pu/Pu3 Co eutectic at 408°C to the 7 Ce/Ce24Co11 eutectic at 42Z°C, the maximum temperature in the valley being 443°C; 2) three ternary inter mediate phases, each having an appreciable mutual solid solubility for plutonium and cerium; 3) eleven four-phase equilibria comprising one eutectic, four peritectics, and six Class II reactions; 4) a pseudobinary section between the ternary phase A and the y Ce solid solution, and another such section between the 6 Pu solid solution and the 77 phase (Pu3 CO) containing cerium in solid solution. ALLOYS of plutonium that are completely molten at temperatures in the vicinity of 500°C are of interest for use in the liquid state as fast reactor fuels. Since exploratory work1,2 on Pu-Ce-Co alloys had indicated that a "eutectic" valley extended across the ternary system between the Pu-co[6 Pu/n (Pu3co)] and the Ce-CO[? Ce/? (ce24co11)] binary eutectics, thus allowing alloys of any plutonium concentration to be selected within the temperature limitation, the present investigation was begun for the purpose of accurately defining the "eutectic" valley. However, when the existence of three ternary intermediate phases and the consequent complexity of the liquid-solid equilibria were discovered, the investigation was expanded to cover the complete system, except for the corner between the isomorphous series PuCo2-CeCo2 and pure cobalt. 1) EXPERIMENTAL The purities of the alloy components are given in Table I. Alloy buttons, each weighing about 5 g, were prepared by arc melting the accurately weighed components (±0.1 mg) under a purified He-Ar atmosphere. Weight loss as a result of melting was usually less than 1 part in 1000; therefore, the buttons were not chemically analyzed. One half of each button was re-melted by induction heating in vacuo in a magnesia crucible and furnace-cooled, so as to produce a somewhat coarser microstructure than that of the rapidly cooled arc-melted button. About 20 g of each alloy to be examined by thermal analysis were remelted in vacuo in a tantalum crucible of the inverted thermocouple well type. The thermal, X-ray diffraction, heat treating, and micrographic methods used in this investigation were essentially the same as have been described in earlier reports.3,4 Two etchants for these alloys were found to be satisfactory: A) 8 (parts by volume) orthophosphoric acid, 5 ethanol, and 5 glycol; B) 7 tetraphosphoric acid, 36 water, and 57 2-ethoxyethanol. Etchant A was used at 5 to 6 v for 15 to 20 sec, and etchant B was used at 10 v for 10 sec. 2) THE LIMITING BINARY SYSTEMS 2.1) Plutonium-Cerium. The phase relationships of this system have been investigated by Ellinger, Land, and Cramer,5 and by Selle and Etter.6 The over-all agreement of their phase diagrams is good, but there are some discrepancies in the positions of some phase

Jan 1, 1967

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944