Search Documents

The papers discussed in the following pages were presented during two sessions of the Geophysics Education Committee of the Mineral Industry Education Division on Feb. 17 and 18, 1941. At the first meeting, to consider the "Influence of Geophysics upon Geology Curricula," this Committee was joined by the Geophysics and Mining Geology Committees of the A.I.M.E., the Society of Economic Geologists, representatives of the American Geophysical Union, and delegates from the Committees on College Curricula and on Applications of Geology of the American Association of Petroleum Geologists. Quentin D. Singewald and Sherwin F. Kelly presided. At the ensuing session, especially emphasizing the integration of geology, physics and chemistry for the solution of earth problems, the joint participants with the Geophysics Education Committee were the Geophysics Committee, and representatives of the American Geophysical Union and of the Committee on College Curricula of the American Association of Petroleum Geologists. Richard M. Field and W. R. Chedsey presided. In the following summary of the discussion at the two meetings, written discussion submitted subsequently is not differentiated from that offered orally at the session. A provisional report of the Geophysics Education Committee was presented at the second session, and some of the following discussion refers to it. This report has not been printed (it is anticipated that a more comprehensive, final one will be rendered at the 1942 annual meeting), but a few mimeographed copies of this provisional report are at the A.I.M.E. headquarters and will be mailed on request. . Dr. W. P. HAYNES presented some notes prepared by Dr. F. H. LAHEE, Chairman of the American Association of Petroleum Geologists' Committee on College Curricula. This Committee's inquiries reveal the general opinion that a four-year academic preparation is inadequate, five or six being advisable. The fundamentals, mathematics, physics, chemistry, and English composition, should be stressed in the first three years, with specialization in the last two or three years. Some companies provide an apprenticeship period, and themselves give additional training.. During academic years more attention needs to be given to engineering training, to field mapping, and in geology to stratigraphy and sedimentation. The amount of mere memory work should be cut, and men trained to observe and reason. Dr. Lahee emphasized the need of more adequate preparation in English composition, because of the inability of many graduates to compose acceptable reports. SHERWIN F. KELLY pointed out that much time in university training, which ought to be devoted to technical subjects, was taken up with English courses. He emphasized that it is the part of the universities to demand of the high schools that the students they send to the university be properly trained to speak and write English. Prof. W. T. THOM protested against the crowding of high-school material into already overcrowded college curricula. C. E. DOBBIN, chairman of the Committee on Applications of Geology of the American Association of Petroleum Geologists, described briefly the work of his committee in publicizing geology, and said that it found a widespread popular interest in the subject but a lack of appreciation of its importance. He recommended that attempts to coordinate the works of geologists and geophysicists be expanded somewhat, toward the further developing and encouraging of a "species of geopolitician" capable of assisting the progress of geology and geophysics by more vigorous advertising of

Jan 1, 1941

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

By R. L. Wilcox, M. L. Fuller

Most commercial alloys undergo changes in phase composition after casting. This is a natural result of the fact that the alloys are not in a state of phase equilibrium as cast and phase changes will therefore take place, with more or less rapidity, in an attempt to attain equilibrium. The practical aspect of aging in zinc-Alloy die castings concerns the changes in physical properties and in dimensions that may accompany aging phase changes. Harmful alterations have been reduced to a minimum and zinc-alloy die castings are being produced today that are so stable with respect to dimensions and physical properties that they are entirely suitable for most practical purposes1. In the first paper2 of this series, and in this paper, aging phase changes of zinc-alloy die castings have been investigated and the possible influence of these changes on dimensional changes of the castings has been evaluated and compared with the dimensional changes actually experienced. The change of dimensions has been selected for practical comparison in these papers because the effect of phase changes on the dimensions of a casting is directly calculable from X-ray crystal-analysis data of the phase structure. The die-casting alloys considered contain, in addition to zinc, 4 per cent of aluminum, about 0.03 per cent magnesium, and from 0 to 3 per cent of copper. It was shown in the former paper that the eutectoidal decomposition of the beta aluminum-zinc phase, while intrinsically capable of causing a considerable shrinkage, can have very little effect on the observed shrinkage of die castings because it takes place within a few days of aging, whereas the observed shrinkage continues for five weeks. It was therefore concluded that the other existing phase change, namely, the segregation of secondary phase from the zinc-base solid solution, must account for the major portion of the shrinkage.

Jan 1, 1936

By R. S. Sandhu, L. E. Baker, W. Y. Shieh

The finite element method of analysis was introduced by Clough.1 Within a short period, it has developed into a powerful solution technique in structural and continuum mechanics. It has been used to solve boundary value problems in two and three-dimensional elasticity.2-5 Anisotropy and heterogeneity of materials were allowed for at the earliest stages. 1,4 Its application has been extended to allow for cracks,5 creep and viscoelasticity, 6,7 incremental construction,6-8 nonlinear elasticity3,9 effect of joints in rock,10 and to materials with different behavior in tension and compression.7 Because of its versatility, the finite element method has found increasing application in the field of rock mechanics. In fact, several of the more significant developments have been motivated by problems in this field. Elasto-plastic material behavior based on the incremental or rate-type theory of plasticity rather than the deformation theory was considered by Reyes and Deere11 A material law based on a generalization 12 of the Mohr-Coulomb criterion was used. In this chapter, the formulation of material laws developed by Reyes and Deere 11 is used. An efficient analysis procedure, incorporating recent developments in finite element analysis, is developed for plane-strain conditions. To demonstrate its effectiveness, the procedure is applied to three cases, one for which an exact solution is available, another for which field observations had been made, and a third one for which a parallel study was made, using an accepted limit-equilibrium method.

Jan 1, 1970

By S. S. Hartranft

FuRnace-men of the present day agree very nearly as to the best cooling-devices for the protection of blast-furnace hearths and boshes, and the best location of the cooling-system in the brick-work for the maintenance of favorable furnacelines throughout the blast. The replaceable bronze and copper plates are practically faultless; and there seems to be no reason why a furnace-hearth and bosh should not be held in good condition, by intelligent management and the use of replaceable plates, for a period several times the length of the average blast of to-day. While furnace-men have taken these .precautions to protect the hearth and bosh beyond the life of the lining, the portion of the lining above the mantle has been partly protected by some and wholly neglected by others. Some would not construct a furnace without mantle-plates, and others would not construct a furnace with them. In most cases, furnace-men have either trusted to Providence or to the bosh-plates for the continuance of favorable working-conditions above the mantle, and the prolongation of the life of the lining; consequently furnaces are constantly blown out for repairs to the lining, or for relining, when the hearth and bosh are in good enough condition to last through another blast. The following extract from one of Mr. James Gayley's con-

Jan 1, 1901

By A. M. Gaudin

THE large increase in the use of selective flotation as contrasted with the collective flotation of a few years ago has focussed attention on the desirability of achieving accurate control of the pH of mill circuits. Although it is well-known that alkaline circuits result in dropping pyrite and that acid circuits conversely float it, but drop the gangue, there is little that is known, beyond question, ass to the action of the acidity or alkalinity of the circuits. A complete answer is not available at present but experiments -are now in progress at the University of Utah, whose aim is to find out what the effect is on recovery of a change in hydrogen-ion concentration and how this change is brought about. Broadly speaking, a change in hydrogen-ion concen¬tration seems to affect either the mineral surface, as was suggested by A. W. Fahrenwald in his paper "Surface Reactions in Flotation"1 (TRANS. 70, 647) or the attachment of the collecting agent on the mineral surface.

Jan 1, 1929

By W. C. Winegard, C. J. Beinjessner

PREVIOUS investigations 1,2 of Fe3P described by pearson3 and schubert4 show that Fe3P has a bct unit cell having four Fe3P tetrahedra centered around each lattice point. The space group is 14, No. 82, and all atoms occupy general positions 8(g). The cell dimensions3 are: a = 9.090, c = 4.446 kX, with an axial ratio of c/o = 0.4891. We have measured the lattice parameters of Fe3P, using a Fe as an internal temperature standard, at 23°, 414°, and 678°C and computed the thermal expansion over this temperature range. The Fe,P was prepared by melting under vacuum (after flushing with argon) a commercially pure iron and "ferrophosphor" in a high-frequency induction furnace. Part of the ingot was crushed for X-ray examination and for chemical analysis. X-ray diffraction and light microscopy indicated iron phosphide (Fe3P) present as the major constituent and a small amount (about 5 pct) of a Fe. Chemical analysis showed 0.05 wt pct Si, 0.008 wt pct N, 0.018 wt pet C, and less than 0.02 wt pct each of other metallic elements. X-ray diffraction powder patterns were obtained from a mixture of iron and Fe3P sealed in an evacuated quartz capsule using a Unicam high-temperature

Jan 1, 1968

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By H. P. Moore, R. W. Fenn, Harold Margolin, W. R. Hibbard

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.' Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference 'R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

By J. W. Rutter, K. T. Aust

THE object of the experiments to be described in this report was to determine, first, which grains, out of a large number introduced into a sample in which their growth could proceed, were able to grow most successfully; and, second, the factors which control their growth selection. In an earlier study of grain boundary migration in high-purity lead,' it was found that, under some conditions, the most successful grain in an experiment of this type bears a special orientation relationship to the grain into which it is growing. The present work represents an extension of the previous study, directed at the determination of the orientation relationships which appear under a wider variety of conditions. Experiments of this general type have been done using commercial aluminum2 with somewhat conflicting results. In the present experiments, in contrast to the above,' the sample composition was a principal controlled variable, resulting in a considerable clarification of the phenomena observed. EXPERIMENTAL TECHNIQUE The experimental technique used in this investigation was essentially that employed previously in studies of grain boundary migration kinetics.1'3 The material used was zone-refined lead with various small amounts of tin or silver added to study the effect of varying the sample composition. The specimens were in the form of single crystals, about 1/4 in. 1/4 in cross section by 3 to 4 in. in length, grown from the melt in a horizontal graphite boat. A crystal grown in this way generally contained a lineage or "striation" substructure of the type shown in Fig. 1 of Ref. 1. This substructure consists of an array of low-angle boundaries which partition the crystal into regions misoriented from each other by a few degrees. The substructure constitutes a source of driving energy, estimated to be about 4000 ergs per cc, for the migration of a large-angle grain boundary into the striated crystal. New grains were introduced by plastic deformation in compression of a localized reglon at one end of the sample. Re-crystallization occurs at room temperature in the deformed region, introducing a large number of new, striation-free grains into the specimen. These grains are able to grow into the melt-grown crystal on annealing at a suitable temperature. The stria-tions are removed by passage of the grain boundary, as the substructure energy is utilized to produce the boundary migration. Usually, only one or two of the recrystallized grains persist after growth has occurred for about 1 cm out of the deformed region. Laue back-reflection X-ray photographs were obtained to determine the orientation relationship between the melt-grown crystal and the recrystallized grain or grains which grew most successfully in each specimen. EXPERIMENTAL OBSERVATIONS Fig. 1 shows the results obtained for a series of specimens to which had been added tin in the range from 0 to 5 ppm by weight. In this figure is plotted, in the standard stereographic triangle, the single axis about which the most successful recrystallized grain or grains are related to the starting, melt-grown crystal by the smallest rotation. The range of angular rotations observed about such axes is indicated beside each stereographic triangle. The results shown in the stereographic triangle on the left, Fig. l(a), were obtained by localized deformation at one end of each specimen at room temperature, followed by annealing in a furnace which had been preheated to 300°C. The furnace atmosphere was argon. It will be seen that the orientation relationships observed between the melt-grown and recrystallized grains are quite random. On the right, Fig. l(b), are shown results for samples in which the de-

Jan 1, 1961

By C. H. Mathewson, Robert Maddin, W. R. Hibbard

A SATISFACTORY mathematical relationship between shear, elongation and change of orientation in the axial straining of a single crystalline rod or wire may be based on a simple model in which blocks, representing glide lamellae, glide over one another and rotate so as to maintain the original fixed position of the axis as the wire elongates.1 Obviously such a model gives no information concerning strain-hardening or the atomic adjustments at the sliding surfaces and their influence on the internal structure of the blocks. Moreover such an operation could be conducted with rigid blocks only by using self-aligning grips or a flexible attachment which would permit the adjacent blocks to freely assume their changing orientations. There are many unsolved problems (see Andrade2) concerning the manner in which nature departs from the simple model in permitting the essentials of slip, rotation and elongation to occur along with strain-hardening and the appearance of glide lamellae of various dimensions and special characteristics, not fully appreciated at the present time. This paper describes part of an extensive investigation on the development and characteristics of glide ellipses in single crystalline alpha brass rods and is especially concerned with the observation of cross-slip in crystals oriented wholly within the range of slip on a single system according to the generalizations first presented by Taylor and Elam in 1923.3 EXPERIMENTAL PROCEDURE Half inch rods of alpha brass (nominally 70 pct Cu, 30 pct Zn) * were converted into single crystals by melting and gradual solidification in a graphite mold according to the Bridgman method.' In order to remove any coring, the crystals were homogenized at 800°C for 16 hr and tested by etching with a 50 pct nitric acid solution. The back-reflection Laue technique as described by Greninger5 was used for determining the orientations of the crystals. Standard stereographic operations were employed to locate the specimen axis in a triangle of the Taylor and Elam3 projection so that the slip plane and direction could be predicted. The lineage structure reported by Buerger6 was present in the crystals used in this investigation. However, only crystals were used in which the internal differences in orientation did not exceed two degrees. Very little is known concerning the effect of the presence of a lineage structure on the detailed mechanism of plastic deformation.

Jan 1, 1948

By John R. Eckel

A Iaboratory drilling rig has been devised and placed in operation which permits the application of hydrostatic, terrastatic, and formation pore pressures to a rock sample for drilling under controlled conditions. Calibrated rests of this equipment in-dicate qualitative agreerment with field results on the effect of weight on bit, rotary speed, and rate of circ~~lation on drilling rate. Tests under pressure, using water and air as the drilling fluids, indicate that when drilling saturated limestone samples, a pressure differential between hydrostatic and formation pressure is the only pressure which affects drilling rate. A differential in either direction causes a reduction in rate, but the same diflerential from the wellbore into the formation causes the greater reduction. Also, in lime.stone, air favorably affected drilling rote only when compared to water at high hydrostatic pressurre, all other conditions remaining constant. Large increases in drilling rate with air could be obtained in the laboratory only while drilling a shale, which offered a limited permeability to nitrogen and which could be drilled with a differential from the formation into the wellbore. In general, the magnitude of the changes due to the pressure effect were small compared to changes in drilling rate obtainable by changing either bit weight or rotary speed. INTRODUCTION In the course of Humble's drilling research program, the desirability of investigating several factors which lend themselves to laboratory rather than field study became obvious. Principal reasons for this are the expense involved in field studies and the difficulty of exercising the required degree of control. Of primary importance are investigations of the effect of fluid pressure on rock rate, the effect of pressure on rock drillability, and a study of the fundamental mechanics of rock failure and chip generation. Several years ago some work in the laboratory on the effect of mud properties on drilling rate was re- ported to the API', but the completion of this work and the investigation of the other variables affecting drilling rate required equipment somewhat more elaborate than that used on these earlier tests. This equipment has been assembled to form Humble's Drilling Engineering laboratory. To date only the effect of pressure on rock drillability while using water and air has been investigated, and this work is not yet complete. Facilities are available to investigate the effect of fluid properties on rate of penetration, and information is being assembled on a current basis on the mechanics of drilling. The sequence of presentation in this progress report is somewhat different from that in which the data were obtained since the order of ex-

By Walter S. Lutz, J. T. Griffith

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. T. Griffith, Walter S. Lutz

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By W. C. Hagel, H. J. Beattie

Phases present at 2200° and 1500°F (1204° and 816°C) were identified in sixty wrought developmental austenitic alloys possessing wide compositional variations. The bases were iron-, cobalt-, and nickel-rich as well as a base with equal parts of each. There are only two structure types previously not found in similar alloys, viz .-the Co3 W and the Fe3Al types. A molybdenum-rich monocarbide decorates dislocations with unusual clarity. Other results provide correlations between alloy composition and phas e precipitation. Grouping intermetal -lic phases into three general classes : I) geometrically close-packed, 2) topologically close-packed, and 3) bcc derivatives, the nickel base prefers the first, the iron base the second, and the cobalt base the third—each base tending to shun the other two classes. Thus, a crystal-chemistry effect previously noted by Laves and Wallbaum can he expanded for these Group VIII elemental bases. There appear to he no quaternary or higher -order structure types requiring more than three atomic species. AFTER studying aging reactions in many diverse commercial austenitic alloys1-4 as a function of detailed time-temperature variations in heat treatment, it became apparent that matrix composition influenced structure types and morphologies to a large extent. These tendencies were related4 to a crystal-chemistry effect uncovered by Laves and Wallbaum.5,6 We have now directed our efforts to exploration of the whole ternary field, covering the standard base elements—iron, cobalt. and nickel— with 10 to 20 pct Cr and moderate amounts, up to 10 pct, of the usual alloy additions. Solutioning and aging treatments were held constant with major emphasis on X-ray identification of microconstituents. The possible existence of exceptions to the Laves-Wallbaum effect, or any new phases, was sought. Phases appearing in austenitic alloys can be classified as geometrically close-packed (gcp), octahedral or nonoctahedral interstitial compounds, topologically close-packed (tcp), semicarbides, and bcc derivatives. Crystal structures of the first four classifications can be visualized as a dense packing of semirigid spheres of different sizes, while the bcc derivatives represent a less efficient packing of spheres. The Laves-Wallbaum effect involves the gcp and tcp phases. Gcp phases possess both tetrahedral and large octahedral interstices; examples are Ni3Ti(n), NiSAl(y'), Co3W(E), and other ordered AB3 compounds where B atoms are smaller than A. Their precipitation is primarily intragranular, presumably coherent with an austenitic matrix, and a chief source of strengthening. Most octahedral interstitial compounds (e.g., CbC, Tic, TiN, Mo2C) have a gcp lattice of large metal atoms which accommodate small carbon or nitrogen atoms in the octahedral interstices. The compound Ti2SC, previously designated Y phase or T phase, can, with some reservation due to its partial co-valency, be placed in this category.7 The nonoctahedral interstitials (e.g., M7C3, Fe3C) represent close-packings of spheres in structures that provide larger triangular-prism interstices for carbon, since the octahedral interstices formed by chromium and iron atoms are too small. Tcp phases possess only tetrahedral interstices; examples are Laves (Fe2Ti, Fe2Cb, Fe2W...AB2), p(Fe7MO6, Co7W8.... A8B7), and (FeCr, Co2Cr3)

Jan 1, 1965

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By C. G. Dunn, J. L. Walter

The c/laracterzstics of cube-oriented nuclei ard other matrix grains that are associated with secondary, recrystallization to the cube texture in high-purity silicon iron were investigated by me-tallographic and X-ray methods. The results show that the structure consists of relatively perfect grains of average diameter between one and two times the sheet thickness ad that the texture has a moderately strong (110) [001] component and a weak (100) [001] component. The results also indicate that matrix stability results from the two-dimensional nuture of the graitzs and that cube-orzented nuclei are neither more Perfect nor larger grains than other matrix grains but have a preferred [001] direction in the rolling direction and have a more effective driving force for growth than other grains because of a low (100) surface energy. THE structures and textures of fine-grained rnatrices determine to a large extent the kinds of secondary recrystallization textures that form on annealing. The understanding of secondary recrystallization processes therefore depends on adequate information about the initial matrices. Matrices usually have three characteristics: 1) they consist of fine-grained primary recrystallization structures, 2) the fine-grained structures are stable toward normal grain growth, and 3) they contain secondary recrystallization nuclei. Stability toward normal grain growth may be due to either a strong single orientation texture (texture inhibition)' or a dispersed second phase (dispersed phase inhibition).2"4 If normal grain growth is not inhibited by either of these two factors, it nevertheless stops when the average grain size is between one and two times the sheet thick- ness.5 This thickness effect satisfies one of the characteristics of a matrix for secondary recrystallization. Its importance in the development of the cube texture in high-purity silicon iron by secondary recrystallization was pointed out by the authors in a recent paper on tertiary recrystallization7 and will be discussed further in the present paper. Assmus, Detert, and he8 have provided some information on a matrix for secondary recrystallization to the cube texture in silicon iron. They found a (110)[001] or Goss texture with enough spread about the rolling direction to include a small amount of the (100)[00l] orientation. The distribution of the [00l] directions was strongest parallel to the rolling direction for both (100) primaries and cube secondaries. These authors found no correlation between size of a matrix grain and orientation and concluded that some property other than size must be the distinguishing characteristic of the cube-oriented nucleus. No consideration was given, it

Jan 1, 1961

By Edward Keller

THE ASSAY FOR COPPER. SOMEONE some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The. writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he :feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample 1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2, g. of copper) measured out for the electrolytic deposition; in the other Method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed -a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 8, 1913