Search Documents

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By R. H. Widmyer, G. M. Wood

This investigation was prompted by the absence of a simple, accurate method to predict optimum second stage separation pressure in three stage separation operations. Three stage separation as used here includes two separators plus the stock tank. The first stage pressure is usually fixed by gas sales conditions and the third stage is at atmospheric pressure. Thus, the second stage pressure is the only one that may be varied in-discriminantly during production operations. No variations in temperature were considered in this study, even though it will vary among systems, for a change in temperature has little effect on the optimum pressure. Optimum pressures may be determined from flash calculations, but these are tedious unless a computer is available. An early attempt to develop a simpler method&apos; yielded an equation which gave the optimum pressure only as a function of initial and final pressure. Experience, however, confirms theoretical relationships which show that composition as well as pressure and temperature must be a factor. This indicates that the basic relationship should be an equation of the form, where P, is second stage pressure, P, is first stage pressure, A is a function of P. (stock-tank pressure) and the system composition, and n is a function of the number of stages and the system composition. Fig. 1 shows the basic variation of P2 with P for a fixed system composition. A series of such figures clearly showed the effect of composition. The peak of each curve reflects that second stage pressure at which the stock-tank recovery (gal/MMcf) residue gas is a maximum value. DEVELOPMENT OF NEW CORRELATION Wellstreams having 17 different analyses, ranging from low gravity crude to condensate, were used to determine the effect of composition. Each wellstream was flashed through three stages to determine the optimum second stage pressure for each first stage pressure. Equilibrium vaporization ratios proposed by Latham and Campbell were used throughout. The heptane plus fraction, for simplicity, was assumed to have the properties of octane. The results were subjected to an empirical analysis in an attempt to develop a correlation- that would be (1) simple, (2) accurate, and (3) eliminate the need for any flash vaporization calculations. This analysis yielded two equations, one for wellstreams having a specific gravity greater than one (air = 1.0) and one for those less than one. For crude streams (specific gravFor condensate (specific gravity < 1.0),

By A. J. W. Headlee

RECENT interest in germanium centers around its use as a semi-conductor of electricity in electronic devices. It is generally believed that germanium transistors, diodes, triodes, photocells, and rectifiers will largely replace the present-day vacuum tubes. The germanium electronic devices are much smaller, lighter, and more resistant to shock, and they require only a small fraction of current required for conventional devices. Hence only a small amount of heat is given off by the equipment. This development will require many times the quantity of germanium now being produced, which in 1948 was approximately 1000 lb1 and was obtained almost entirely from zinc ores in Missouri, Kansas, and Oklahoma. No one knows with certainty what the demand will be for germanium by 1956. It may be 40,000 lb.1 Known concentrations in zinc ores are not sufficient to

Jan 10, 1953

By John C. Osmond

One of the least known geologic regions in the U.S. is the area now called the Basin and Range Province. It is paradoxical that so little geologic information has been compiled for a province that has yielded billions of dollars worth of metals and is currently producing a small amount of oil. Regional stratigraphic studies of parts of this large territory have been published only recently, and regional structural interpretations of even parts of the province are rare in the literature. This, of course, does great injustice to the earliest workers: Gilbert, Russell, Le Conte, Spur, Louderback, and others, who recognized the area as distinctively different from the rest of North America. Their simplified picture of the structure of the ranges and the province as a whole is the groundwork for present understanding and has never been superseded. Since their early works, however, geologic data from the province has consisted largely of detailed reports of widely scattered mining districts. Each district has been described as though it were an island in an unknown sea.

Jan 3, 1960

By E. H. Dix

The success of the Charpy impact test in the steel industry has led those interested in aluminum alloys to investigate the possible application of this test to aluminum and its alloys. In this paper are set forth the results of a few preliminary tests made at the Lynite Laboratories of the Aluminum Manufactures, Inc. In order to study more thoroughly the significance of the Charpy test, slow-bending tests have been made duplicating the arrangement of the impact machine. Tests have been made on both notched and unnotched specimens of a series of copper-aluminum alloys. Apparatus The standard American-made Charpy impact machine delivering a blow of over 200 ft.-lb. was much too large to test aluminum-alloy specimens of the same type used for steel, so that it was necessary either to adopt a larger specimen or to have a special light-weight hammer made. Since there is no known relation between specimens of different sixes, even though geometrically similar, it was decided to adhere to the 10 by 10 mm. specimen. Accordingly, Sauveur and Boylston, the American makers of the machine, were asked to construct a special light-weight pendulum adapted to their standard machine, this pendulum to have one-tenth the capacity of the standard. The writer wishes here to acknowledge his indebtedness to Mr. H. M. Boylston for the personal interest and care exercised in constructing this pendulum. The machine with the light-weight hammer in place is shown in Fig. I. It is mounted on a concrete foundation with the concrete covering the flange on the base of the machine. Vibration is further prevented by four 5/8-in. (15.8 mm.) foundation bolts. The large standard hammer shown against the wall was also used for some of the unnotched bars that required more than 20 ft.-lb. to rupture. When the light-weight hammer was received, it was carefully cali-

Jan 1, 1921

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924

By C. J. Ramsburg

THE construction and operation of by-product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. CARBONIZATION PROCESS Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 950°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe. This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about I 7 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over 2000°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 1/2 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

AT the fall meeting of the Iron and Steel Division, Oct. 4, 1934, in New York, a symposium was held on Slag Control in the Making of Iron and Steel. The chairman was J. H. Nead and the vice chairman, G. B. Waterhouse. The latter presided at both morning and afternoon sessions. The papers and discussions were presented in the order in which they appear on the following pages. To meet space requirements, much of this material has been considerably condensed. CONTENTS [ ]

Jan 1, 1935

By Reginald E. Hore

I. INTRODUCTION. SINCE the discovery of silver at Cobalt, Ontario, in 1903 more than 100,000,000 oz. of silver have been produced b: the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the next five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of about $26,000,000. For 1910 the production was 30,558,825 oz. valued at $15,436,894, and yielding a profit of about $9,000&apos;,000 The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, are given in Table I. TABLE I.-Silver-Production of the Cobalt District, 1904 to 1909 SMELTING-ORE. Production. Value. Silver-Content. Value Per Ton Ounces. Oz. Per Ton. 1904 206,875 $111,887 1,309 $708 1905.:.... 2,451,356 1,360,503 1,143 634 1906 5,401,766 3,667,551 1,013 687 1907 10,023,311 6,155,391 677 416 1908 18,022,480 8,468,293 736 363 1909 22,436,355 10,809,872 809 389 CONCENTRATES. 1908 1,415,395 $665,085 1,240 585 1909 3,461,470 1,651,704 1,174 559 The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-or( is largely high grade, averaging about 3,000 oz. per ton- A

May 1, 1911

Allan Gibb, Queensland, Australia (communication to the Secretary*):—It is gratifying that Mr. Edward Keller,&apos; who has clone so much work elucidating the principles of copper-metnllurgy, should have subjected only that portion of our investigation relating to magnetic iron oxide to anything like adverse criticism. Situated as we were on a rnining-camp, it was impossible to undertake work that would cover all the intricate possibilities connected with the materials commonly classed as matte. We therefore began the investigation on matte produced from ores that contained no other components than the sulphides of copper and iron that would be likely to enter into the composition of matte. We were, accordingly, free from ally possibility of magnetic iron oxide entering the matte, unless it were formed in the operation itself. The work done on this subject was incomplete, and the results thereof recorded as giving only negative evidence as to the absence of magnetic iron oxide. It would have been better to have left the matter open, as " not proven." The trend of the investigation was to account for the insufficiency of sulphur in matte to satisfy the requirements of ferrous and cuprous sulphides. So far as our deductions are correct, it was unnecessary to consider the (in our samples) somewhat doubtful constituent, magnetic iron oxide. The mattes that mere investigated were among those mentioned by Mr. Keller, " which scarcely show ally magnetic property." The samples showed no such property. There was no unaccountable variation in the specific gravity, which only varied, as would be expected, with the proportion of ferrous sulphide. I have had experience in smelting ores of which the gangue was a siliceous magnetite, both in blast- and rever-beratory furuace. The mattes so produced contained magnetic

Jan 1, 1908

National Society of Professional Engineers has thrown its full sup- port behind pending legislation to appropriate $500 million for national conversion efforts that would provide employment opportunities for engineers, scientists, and technicians who are currently unemployed because of the decline in defense and aerospace programs. Known as the Davis-Giaimo bill, the proposed legislation would raise total Federal investment in science and technology to an adequate annual spending level and keep it proportionally equal to the growth in the GNP. If passed, the bill would increase and maintain Federal obligations for civilian-oriented research and development activities to a parity level with similar obligations for defense research development. U. S. Bureau of Mines has cataloged and placed on open file an inventory of U.S. coal deposits which can be economically strip mined at today&apos;s production costs. The costs include charges for reclaiming the mined land as required by 21 states. The report claims that some 46 billion tons of bituminous coal and lignite can be strip mined under present economic conditions, and that 32 billion tons of the total is classified as having less than 1% S. The report reviews strippable coal deposits by state, by county, by coal seam, by coal-seam thickness and by sulfur content. The report also gives an up-to-date summary of state laws on surface mine reclamation. Open-file copies of "Strippable Reserves of Bituminous Coal and Lignite in the U.S." may be consulted in Washington, D.C., at the Department of the Interior library and at U.S. Bureau of Mines offices in Pittsburgh, Denver, San Francisco. Dallas. Spokane, and Douglas Island, Juneau. Alaska.

Jan 1, 1971

By Robert W. Bartlett

A computer model for predicting the rate of oxidative leaching of copper from fragmented low grade sulfide ores is presented. The model involves the kinetics of the dissolution of chalcopyrite grains and solution diffusion of oxygen within rock pores. Adjustable curve fitting parameters are not used. The model was tested by comparing computed extraction curves with experimental results for a -11 inch ore obtained by block caving and leached at 90°C and 400 psi oxygen for one year at the Lawrence Livermore Laboratories.

Jan 1, 1973

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By M. Albertson

The purposes of this statement are to define a problem that exists in regard to the estimation of developed petroleum reserves, to analyze the problem in an abstract manner, and to discuss it as an introduction to certain papers that follow. The problem is to devise and develop a suitable procedure to permit more accurate estimates of developed petroleum reserves. Part of the problem is to make such estimates available earlier in the life of any particular pool. The problem of securing more accurate estimates of developed petroleum reserves existed prior to curtailment of production. With curtailment, however, the problem became acute, some of the more prominent reasons being as follows: 1. The standard method of estimation depended on production-decline curves. This method is inapplicable while curtailment prevails and available methods arc insufficient. 2. The retarding influence imposed by wide open flow conditions upon overdevelopment is absent. Great losses of capital by overdevelopment can now occur before realization of the true situation occurs, or before effective steps can be taken to stop such wastage. This increases the need for early, accurate estimates. 3. Above-ground stocks have diminished and the equivalent of such supply tends more and more to be retained underground in the natural reservoirs. It becomes increasingly necessary to know accurately the amount of these stocks. To direct attention to an additional point of different nature: improved accuracy of reserve estimation can be obtained only by closer scrutiny of the factors that determine recovery. This examination and the resulting efforts to measure the effect of these factors in terms of ultimate recovery must tend to improve ultimate recovery. The statements regarding the acute nature of the problem also indicate to some extent the importance of the problem and the necessity of finding a solution. Developed reserves of the industry, and of individual opera-tors, are one of the great factors that properly should determine explora-

Jan 1, 1936

By E. Eichen, G. S. Ansell. L. R. Sefton

A Technique for the Preparation of Thin Films of Two-Phase Alloys Suitable for Use in Transmission Electron Microscopy In order to obtain foil sufficiently thin to permit transmission electron microscopy of two-phase alloys, particularly alloys in which the second phase is present as a very finely dispersed second phase, a technique has been developed to permit the thinning of these materials without either the large degree of pitting present in the electrochemical or chemical thinning process or the slicing of the second phase particles accompanying the mi-crotoming process. The metal or alloy to be thinned is first ground to initial sheet thickness of approximately 0.002 in. by hand grinding on 4/0 emery paper. This starting sheet of material is then reduced in cross section by an air-abrasion technique using an S. S. White dental abrasive unit. This unit consists of a supply of compressed CO, which provides a stream of high velocity gas impinging on the metal surface. Incorporated in the machine is a hopper-type of device in which fine abrasive particles of alumina are introduced into this high velocity gas stream. The abrasive particles are irregular in shape, approximately 30 across. If any particles are introduced into the sample during thinning, they should be readily observable. Impingement of this gas abrasive mixture on the metal surface causes rapid removal of the metal in a rather uniform manner. The rates of metal removal may be adjusted by both regulating the gas pressure and amount of abrasive material introduced into the gas stream. By moving the gas stream abrasive mixture slowly about the specimen or sheet surface, a large area of the sheet may be uniformly reduced to a thickness which is then suitable for use in transmission electron microscopy. Attendant with this metal removal is a result in cold working of the metal surface due to the impingement of the abrasive particles. The resultant foils, therefore, if made from materials which are desirable to view in the annealed condition, have to be subsequently heat treated. If the alloy from which these foils have been made has been initially heavily worked or deformed during manufacture, then no subsequent heat treatment is, necessary as in the case of the SAP-type alloys. Following this initial abrasive thinning technique, the material is then given a final electropolish which is just sufficient to remove any oxide which has formed on the metal surface during the abrasion technique. Care has to be exercised in this technique to make sure that none of the attendant problems associated with the chemical or electrochemical removal process are encountered. An electrolyte solution which has been found suitable for aluminum-aluminum oxide SAP materials is one containing 78 ml of perchloric acid, 120 ml of distilled water, 700 ml of ethanol, and 100 ml of butylcellosolve. The current density used is 1 amp per sq cm and a polishing time of 3 sec on each side of the foil is used. Extreme care must be used in choosing the current density and time to ensure that just the oxide film on the specimen is removed. Times or current density which are greater than this will lead to perforation of the film due to the removal of the A1,0, particles or a complete loss of the film due to complete solution of the matrix. Once the oxide film is removed the specimens must be kept in alcohol until placed in the microscope to prevent any further oxidation. Fig. 1 shows -an electron micrograph at X28,000 of a thin foil of an aluminum-aluminum oxide SAP-type alloy prepared using this technique. The alloy consists of a matrix of commercial purity aluminum containing a very finely dispersed second phase of aluminum oxide flakes. In the electron micrograph, the dark patches are the aluminum oxide particles. The lighter portions of the micrograph are the aluminum matrix. Within the aluminum matrix, the dislocation structure of the alloy is clearly visible. This structure consists of intersecting twin boundaries and single dislocations. No abrasive particles were observed in the samples. In addition, thin films of commercial purity aluminum were prepared using this method and observed in the electron microscope. Here also, there was no evidence of abrasive particles introduced in the samples. The technique presented provides a satisfactory method for the production of thin films of aluminum-aluminum oxide SAP-type alloys for use in transmission electron microscopy where none of the usual thinning techniques appears to be satisfactory.

Jan 1, 1962

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By R. P. King

Flotation plant simulation, a relatively recent methodology in mineral processing, is defined and corresponding uses are discussed. Typical simulation structures are compared. Current problem areas exist although these are not insurmountable. Following a brief state of the art discussion, the N. I. M. simulation program is reviewed. In general, digital plant simulation is expected to be of substantial benefit in the near future.

Jan 1, 1976

By H. H. Otto

COMPARED with 1939, the year 1940 has seen no material change in the production of anthracite. Many factors seem to indicate a stabilized anthracite production of approximately 50 million tons per year. The present war has stimulated demand in the Cana¬dian and New England markets, which were formerly furnished with a portion of their needs from Great Britain and other European countries. Neither has there been any material change in the "bootleg coal" situation. This problem is more serious in the Southern anthracite field than in the Hazleton, Wilkes-Barre, and Scranton areas. One reason for this is the nearness of the Southern field to the large anthracite markets in Philadelphia, Washington, Baltimore, and Harrisburg. During the past year no new large

Jan 1, 1941

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield-point of 16,000 lb. for pure electrolytic iron, one reaches a -maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated Yensen observed an enormous drop in elongation and area reduction at about 2.65 per. cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to. 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a&apos; range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.&apos;

Jan 1, 1955