Search Documents

By Lyman Johnson

Single crystals qf copper in "single slip" orientatiorzs have been deformed in compression. During defortnation all of the independent deformation parameters have been measured. These parameters consist of thefive strain components and three components descrihing the lattice rotation. By a finite strain analysis these pararmeters , forrming a deformation gradient martrix, are related to the amounts of slip on each of the twelve slip systems. The results show that the amount of secondary slip is about equal to the amount of primary slip. This is an order of magnitude larger than has been believed previoutsly. ACCORDING to early theory and experiments, when a single crystal of a fcc metal is deformed in tension or compression it should deform by slip on only one slip system until the stress axis reaches a symmetrical orientation.' However. the observation of a large increase in the secondary dislocation density during ..single slip" makes it clear that some slip does occur on secondary systems. Knowledge of the amount and distribution of this secondary slip is essential to a complete understanding of the mechanisms of single-crystal deformation. Ahlers and Haasen 2 and Mitchell and Thornton1 have tried to detect the amount of secondary slip in single crystals of silver and copper, respectively. Each simultaneously measured the angle A, between the tensile axis and the primary slip direction and the length 1 of a gage section of the specimen after incremental amounts of deformation in tension. The measured A, was then compared with the theoretical single slip angle hp. given by sin Ap = j sin . hO where ?o was the initial angle between the tensile axis and the primary slip direction and lo was the initial gage length. In both sets of experiments a small but systematic difference between ?e and ?p was found. This difference must be due to the occurrence of secondary slip. However, as Mitchell and Thornton1 pointed out. nothing quantitative can be said about the amount and distribution of this secondary slip from the measurements that they made. The reason that no quantitative conclusions could be made is because no unique solution for the distribution of slip on the twelve fcc slip systems can be determined from only two measured deformation parameters such as A and 1. There are, in fact, eight independent macroscopic deformation parameters that can be measured when a single crystal undergoes a homogeneous deformation. Physically these can be thought of as the five finite strain components and the three angles describing the crystal lattice rotation. All eight of these parameters were measured by Taylor4,5 for aluminum deformed in tension and compression. At that time the concern was to show that slip occurs on {111 (110) systems in fcc metals, and the mathematics were not available to determine what slip distributions were compatible with the measurements. In this paper the mathematics6,7 are developed that allow the slip distribution to be determined from these measurable macroscopic deformation parameters. The analysis is applied to the measurements of the strain and lattice rotation of copper single crystals deformed in compression. The results show that the amount of secondary slip is an order of magnitude larger than had previously been thought. CRYSTALLOGRAPHIC DESCRIPTION OF A HOMOGENEOUS DEFORMATION The deformation of a solid body can be represented by a transformation matrix F that transforms the un-deformed state into the deformed state. Consider a vector X connecting two material points in the unde-formed material and the vector x connecting the same two material points after deformation, where both vectors are referred to the same set of Cartesian axes. The final vector x is related to the initial vector X by the equation: X = FS. [2] Eq. [2] can be considered as the equation defining F, which is called the deformation gradient matrix. Its components are: If the deformation is homogeneous, the transformation is linear and the components of F are constants. Using subscript notation, if P is the unit vector in the initial direction of a material line, the components of the unit vector p in the direction of the same material line after deformation are given by:

Jan 1, 1970

By Julius Albert Krug

IN the field of mineral resources, today's problems and those we can reasonably expect in the future are so vast that nothing less than world-wide thinking and world-wide planning will suffice. I can imagine nothing more useful for the Institute to do in celebration of its seventy-fifth anniversary than to hold this conference on world mineral resources. Mineral resources are the basis of any nation's industrial production. Without expanding industrial production, the high standard of living found in the United States could not exist. Without such a standard of living it would be most unlikely that we should have a high level of culture. The hope of the world, as I see it, depends very largely on a general rise in living standards everywhere, and in the general increase of the levels of culture including a sympathetic understanding of the problems of other nations. For this reason, the proper use of the world's remaining mineral resources must be taken into account in any plans to safeguard the peace of the world. Being as exasperatingly human as human beings always seem to be,. we usually wait until almost too late to begin our plans to stave off an impending disaster. We do this as individuals, as components of particular States or Governments, and as citizens of the world. We waited, if not too late, certainly a very long time in getting started on the job of world-wide con-

Jan 1, 1947

By E. Miller, K. L. Komarek

Equatiorzs have been derived which related maximum solid solubilities in semicondcting compounds having retvograde solidus curves with 1iqllidus data. Liquidus curves in Lke Pb-Te, Pb-Se, ard PB-S systetris have been defermined by thertrzal aralyses. Fvotrz expevimental maximum solibilities ia CdTe, PbTe, uxd PbS vetvograde tetrperatures hale beep1 calculated. TIze resllts support the concept that under certaiz conditiots pronounced itjlections in the liquidis curves arc indzcatiz:e of retropade solidus curves and that the tenlperatltre of the lmaximum solid solubility will be close to the temperature of the point of inflection in the liquidus curve. The maximum solid solihility within a gvoup of homologous cottrpoods SeetlLs to increase with increasing flatness ol the liquidus curvres. The phenomenon of retrograde solubility in metals, i.e., maximum solubility in a solid terminal phase in equilibrium with a liquid phase, has been theoretically predicted by Van aar' in his calculations of hypothetical binary phase diagrams. It was not until 1926, however, that retrograde solubility was experimentally verified in the Zn-Cd system.' Since then many sys- tems with retrograde solubility have been found, so that at present approximately fifty binary diagrams with a retrograde solidus curve are known.3 Meijering4 has critically appraised the accumulated data and has presented calculations which alloy predictions as to whether or not a solidus line will be retrograde. Interest in retrograde solubility increased when it was found that the solidus curves of germanium and silicon alloyed with a great many doping elements are retrrade. The problem was treated thermody-namically by odkinson,% d all available data on solid solutions in germanium and silicon were summarized by Trumbore.7 Although it is to be expected that intermetallic compounds will also exhibit retrograde solubility, experimental evidence is much more limited. Until now retrograde solidus curves have been reported for the compounds de,' be, Ps:" ne," SnSe," and SnS.13 All these compounds are semiconductors, and the solidus curves were usually obtained by determining the carrier concentration at room temperature of samples equilibrated at elevated temperatures and then quenched. It has been hown,'' however, that it is not always possible to quench in the equilibrium compositions from above a certain temperature. Theoretical discussions have either explicitly excluded intermetallic compounds4 or not treated them with respect to retrograde slubilit.j In the following a thermodynamic treatment of retrograde solu-

Jan 1, 1967

By J. H. Hensley

The mine of the Miami Copper Co. is in the Miami district, Gila County, Ariz., approximately 7 miles west of Globe. In 1906, the General Development Co. secured the ground now owned by the Miami Copper Co., and about a year later discovered ore in a prospect shaft at a depth of 220 ft. The Miami Copper Co. was organized in 1907, the claims held by the General Development Co. were transferred to it, and an active development campaign was inaugurated. The railroad was extended from Globe to Miami in 1909, a concentrating plant was constructed, and the company began producing early in 1911. The unit size of mineral tract in the district is the standard lode claim 600 ft. in width by 1500 ft. in length. Ownerships of land are held in fee. The geology of the district has been described by F. L. Ransome.' The formations of local importance are: The pre-Cambrian Pinal schist, which consists mainly of metamorphosed sedimentary rocks and is commonly of a thinly laminated sericitic variety; the diabase, which is thought to have been intruded in late Paleozoic or early Mesozoic times; the Schultze granite and granite porphyry, considered early Tertiary; the dacite of late Tertiary time; and the Gila conglomerate of early Quaternary. General Items Influencing Mining Methods The bodies of disseminated ore in the district are flat lying masses of irregular outline and variable thickness. As a rule, these masses lack definite boundaries; the orebody follows a curve along one of the main ridges, approximately 5500 ft. in length with a maximum width of 1600 ft. The minerals occur as finely divided and uniformly disseminated chal-cocite in the Pinal schist and Schultze granite. The typical overburden or capping is a barren rusty brown, very friable, highly siliceous, leached schist, or granite-porphyry. The topography of the district is fairly rugged and irregular; the altitude ranges from 3400 ft. above sea level, at the town of Miami, to 3900 ft. on the hills above the Miami orebody. The climate is mild; the mean annual temperature is 63.°F.

Jan 1, 1925

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By A. M. Ribe

Briefly stated, the mission of the traffic manager (currently called a transportation services manager) is to enable his firm to utilize to its best economic advantage the various systems and modes of transportation available to it to bring in its raw materials and ship out its finished products. The function of the transportation services manager is perhaps of more relative importance in industrial minerals operations than in industry and trade generally.

Jan 1, 1970

By C. H. Gerould

I would like to take a moment to consider our polystyrene-silica replica technique, which was developed at the Dow Chemical Co. and which was mentioned in the paper just given by Mr. Thielsch. He stated that he feared that our replica technique would cause difficulty due to deformation of the metal as a result of the application of pressure during the molding process. We at the Dow have never had any reason to suspect that any deformation of the metal was occurring during the molding process. Our procedure has been to heat the polystyrene to a temperature of 160°C. before applying any pressure, at which temperature the polystyrene is a viscous liquid. By so doing the pressure of the polystyrene against the metal is essentially hydraulic and is therefore applied equally in all directions, which we feel should not cause deformation. Our work using this replica technique has brought forth several indications that deformation of the specimen is negligible. These indications are: I. Direct comparisons have been made between the light and electron microscopes when studying a specific spot on a metal surface. These "same spot" studies were obtained by first taking micrographs at high magnification, with a light microscope, of a specific structure that could be readily recog-

Jan 1, 1947

By Morris Cohen, Robert C. Ruhl

The phases in Fe-C alloys over a wide composition range have been studied after splal quenching from the liquid state. Binary alloys containing 0 to 5.1 wt pel C as /cell as a large number of ternary Fe-C-Si alloys with 2.5 to 5.0 wt pct C and 0.3 to 5.1 wt pct Si were attlong those sludied. Olher Fe-C-X alloys, zcilh X being Co, Cr, ,Wn, Ni, and Ru , were also inrestigated after splat quenching. At high carbon contents, a new hcp phase (designaled 6 phase, but different from e carbide) is retained upon splat quenching. The .fraction of this phase varies up lo 97 pcl for a Fe-4.K-1.9% alloy. The composition of the E phase ranges from about 3.8 10 4.8 wt pet C, and the corresponding laltice parameters increase linearly ulith carbon content, while the c/a ratio remains essentially conslc~nl. The E phrtse appears to he a solulion of carbon in E iron, the latler being nornially found only at high pressures. It is deduced that the unit cell of the E phase corresponds to the formula Fe12C3, and llzal il is relaled to tlie ordered slruclures 0.f 6 iron carbide and c iron nilride. The E phase is compared and contrasted to the olher known carbides and nitrides of iron and nickel. An exlrapolaTion of the atomic volume 1,s carhon conlent of /he E pllase lzcts giz.en a neu7 estitnale jor /he alomic volume of E iron, 11.30 cu A, a1 atmospheric pressure and temperature. Other alomic volume relalionships lead to /he co~zpositioti Fe2.iC tor E iron carbide, /he unit cell fortr~ula being -Fe2rClo The E phase undergoes a lulo-slage decomposition upon healing, .forrning firsl rnarlensile plus E carhide, a/ler 1 hr at 140" lo 200°C, slid then ferr ite Plus cementile, after 1 lir a1 330" to 460°C. A1 carbo,l contents between 1.5 and 3.0 LC/ pcl, (he predo.wirzar/t plzase alley quenching is fcc austenite. The retained carbon content of this phase increases with itlcreasing silicon in certain concentration ranges, reaching a maximum of 2.37 wt pct C itz a Fe-2.6C-4.OSi alloy. This is the highest carbon conten1 reLaitled in austenite to date. These high-carbon aus-tenites can be partially tm?zsforttled lo tnartensile hy severe deformation in the temperature range of — 190 to -50°C. TECHNIQUES for splat quenching from the liquid state have been utilized in numerous recent investigations to produce metastable phases in a variety of alloy systems. Among the several ways of splat quenching, the shock-tube method appears to yield the highest cooling rates1-3, 7, 8 and was adopted here. Estimated cooling rates attained in the present experiments ranged from 10' to 10 80Cper sec.' As a part of a research program on interstitial al- loy phases, the Fe-C system was selected for splat-quenching studies. It was hoped that splat quenching would allow high metastable supersaturations of carbon to be retained in solution. Also of considerable interest were the conditions governing the occurrence of the various intermediate phases upon solidification. The alloys investigated included both binary Fe-C compositions as well as six ternary Fe-C-X alloy systems. The known phases in the Fe-C system are summarized in Table I.* Only the ferrite and graphite are ent investigation.14 and is described in detail herein Table II summarizes corresponding data on Fe-N phases, which are also of interest here because of their similarity to the Fe-C phases. EXPERIMENTAL PROCEDURES Alloys were prepared by melting the elements. 99.9 pct purity, in an inert gas nonconsumable electrode arc furnace. The buttons. weighing about 5 g. were remelted twice. were then fragmented. and their interior surfaces were examined for uniformity: if any doubt existed. they were remelted again. Chemical analyses were performed on all the alloys. the accuracy being about k0.05 wt pct. At high temperatures, carbon-containing alloys react with alumina crucibles as follows: If the atmosphere in the splat-quenching furnace does not contain sufficient carbon monoxide the alloy can be depleted of carbon and contaminated with aluminum. Calculations and experimental observations showed that 50 to 100 torr CO partial pressure effectively blocked the above reaction in all the alloys investigated. The splat-quenching equipment in Figs. 1 and 2 provides for evacuation and back-filling with CO-Ar mixtures. The furnace is capable of operation up to 1650°C. and the gettering action of the graphite heating element reduces the oxygen partial pressure in the furnace atmosphere to below 10-5 torr, thus preventing oxidation of the specimens.

Jan 1, 1970

By J. H. L. Vogt

TABLE OF CONTENTS. PAGE Introduction,...........125 I. The Original Source of the Heavy Metals of Ore-DepoBits,. 126 Distribution of Elementary Substances in the Earth's Crust,. . 128 11. The Relation between Eruptive Processes and the Formation of Ore-Deposits, Especially Buch AS have been Produced by Eruptive After-Actions,........ Ore-Deposits Formed by Magmatic Segregation,..... Ore-Deposits Formed by Eruptive After-Actions,..... Cassiterite-Veins and Apatite-Veins,...... Ore-Deposits of Contact-Metamorphic Origin,.... Pyritic Deposits,.......... Veins of Gold, Silver and Lead-Ore,......142 Conclusions,........... 111. The Nature of the Ore-Solutions in Vein-Fissures, and the Metasomatic Alterations along the Ore-Veins,. .. 147 The Association of Vein-Minerals,.......147 Deposition of the Vein-Minemls,........148 Alteration of the Country-Rock,........ Classification of Metasomatic Alterations,...... 149 Additional Observations,......... Kaolinization,..........150 Comparison between Cassiterite-Veins and Lead-Sulphide Veins,. 154 Comparison between Formation of Greisen, etc., and Propylitiza tion, etc.,........... Conclusions,........... IV. Differences of Depth in the Original Positions of EPIGENETIC Deposits ; and the Secondary Alterations of Deposits,. . 158 Original Differences of Depth,. .. .. .. . Gecondary Altemtions of Ore-Deposits,......, Introduction. In the latter part of November, 1900,I received through the Secretary of the Institute the papers of Messrs. Van Hise, Emmons, Lindgren and Weed, presented at the Washington meeting of February in that year, with the request (urged also by Mr. Emmons) that I would furnish for the Richmond meet-

Jan 1, 1902

By T. S. Lundy, J. I. Federer

A graphical method has been developed and tested for separating the effects of grain boundary and lattice diffusion in polycrystalline materials. The method is based on the assumptions that for unidirectional diffusion from a plane source of radioactive material, the penetration of activity far into the specimen from the source is due solely to grain-boundary effects, and 2) pure grain-boundary penetration is described by a linear plot of log activity vs the perpendicular distance x from the source. The former is based on the fact that at any temperature the grain-boundary diffusion coefficient is always very large relative to the lattice diffusion coefficient; and the latter is based on the derivation of Fisher.1 Using these criteria along with appropriate penetration data (in this case, data for the diffusion of Cb95 in pressed and sintered UO2) one first plots the data as log activity vs x2 and as log activity vs x, as shown by curves 1 and 2, respectively, in Fig. 1. A tangent line to curve 2 for large x (curve 3) is then transferred to the x2 plot as curve 4. The subtraction of curve 4 from curve 1 yields curve 5 which represents only lattice diffusion and may therefore be related to the diffusion coefficient by using the appropriate solution to Fick's second law. It should be noted that the method has inherent inaccuracies for small and large values of x2 and only the subtraction at intermediate values can be used. For the illustrated specimen the calculated diffusion coefficient is 3.4 X 10-11 sq cm per sec at1445°C while data using a single crystal of UO2 at the same temperature yielded a value of 2.9 x 10-11 sq cm per sec.2 The same method of subtracting grain-boundary diffusion effects to obtain lattice diffusion coefficients has been successfully used to determine self-diffusion coefficients of Th230 in polycrystalline thoria.

Jan 1, 1962

By Peter G. Groer

Several methods1-3 are being used to determine the WL and individual Rn-daughter concentrations in uranium mine atmospheres. The best of these methods is the one given in Ref. 3. According to this method, the WL and the Rn-daughter concentrations are determined from the total a-counts observed during three consecutive time intervals. Its only disadvantage lies in the fact that rather involved calculations are necessary to convert the observed counts into WL or pCi/l (picocuries per liter). There are, however, counting intervals that give simple weighting coefficients for the observed counts. This fact makes it possible to convert from a-counts to WL or pCi/l with the aid of a graph. After some trial runs on a computer the following equations emerged as the basis for the most practical procedure: [ ] NA, N.., and & stand for the number of RaA, RaB, and RaC atoms per liter of air. C(t1,t2) denotes the counts observed from time t. to time t2 (in minutes) after the end of the 5-min sampling period. E is the detector efficiency and V is the flow rate in liters per minute. With an accuracy loss of less than -5% one finds from [Eq. 1] by adding the corresponding terms: If the WL would have been calculated according to [Eq. 2] instead of using the graph, the result would have been 0.31. Since the values used for C's under [Eq. 3] represent the exact number of counts from a Rn-daughter mixture in equilibrium with 100/3 pCi of Rn the exact WL of this mixture can be calculated easily. The exact value is: [ ] This shows that the method is quite accurate for the 0.3 WL domain. The precision of the method excluding errors made in reading the graph can be estimated with the help of the following formula: [ ]

Jan 1, 1974

By Jeffrey N. Schuyler

In order to implement the most efficient and cost-effective hydraulic fracturing stimulation treatment within a particular region, a thorough understanding of the in-situ stress state and rock properties is paramount (Smith et al., 1978; Warpinski et al., 1982). Several studies conducted in order to "characterize" formations have provided invaluable insight into the relationship between lithologic properties, depth, in-situ stress magnitude and hydraulic fracture orientation. These studies have substantiated that at shallow depths, rock properties such as tensile strength and permeability can exert a substantial influence on the geometry of an induced hydraulic fracture. In turn, these "directional properties" can be related to existing geologic conditions during the time of deposition or major diagenetic alteration of the rock body. As the depth of the "payzone" increases, the role of the in-situ stresses and therefore the prevailing tectonic conditions becomes the dominant factor in determining fracture geometry. However, reservoir properties cannot be ignored. The porosity, permeability, pervasive fabric element and directional elastic properties can have a significant influence on the success of those tests conducted to measure the in-situ stresses either directly or through secondary observations... for instance, pore-pressure effects on measurements of in-situ stress. The purpose of this paper is to provide, through the use of appropriate field and laboratory examples, a more thorough understanding of in-situ stresses, rock properties and their integrated effect on hydraulic fracture properties. In addition to highlighting and expanding the wide body of existing literature, the case studies cited are designed to encourage mutual transfer of technology from petroleum-related, rock-mechanics efforts to other disciplines.

Jan 1, 1984

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By C. E. Shoenfelt

The year 1939 witnessed the rapid development of several of the more important Rocky Mountain oil and gas areas and the discovery of new oil and gas fields. As a further result of an active year, many oil fields had their productive limits greatly extended or responded to deeper drilling with oil production in lower horizons. In Colorado there was a substantial increase in refinery capacity, with three new units constructed. Its contribution to the crude-oil supply was an important extension of the producing area of a Western Slope field and a deeper oil-producing horizon in an old field east of the Front Range. Occurrences of gas were reported in two wells in northwestern Colorado, but severe winter weather prevented tests and the value of these discoveries cannot be determined at this time. Montana's northern fields were extended and a number of record wells were completed. The North Cut Bank area gives promise of wide expansion in 1940. The gas-producing area of Wyoming's Elk Basin field was extended into Montana on the north plunge of the anticline. The most important developments in Wyoming oil fields in 1939 were extensions to the producing area of Lance Creek and the discovery of a deeper pay in the Tensleep formation at Wertz dome. A new gas field at Horn Valley in the south central part of the state was the only new field discovered, but wildcatting was at low ebb in Wyoming in 1939. Colorado In Colorado, the year 1939 saw the completion of several interesting tests, but largely with negative results. Oil was discovered, however, in a deeper sand in the old Fort Collins field and the productive area of the Wilson Creek field was extended. Gas had been noted in two Western Slope wells, at Yellowjacket-Buford and at Trull, but their volumes had not been determined at the end of the year. Of principal interest, however, were the failures, descriptions of which will be given presently. One of these established a new depth record for Colorado.

Jan 1, 1940

By D. M. Davidson

THE drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of 110 ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered, and is drained by the Piney and Tye Rivers, which are tributary to the James. GEOLOGY The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 45° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelsonite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more promounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,1 the Ti02 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. SAMPLING METHODS AND PROCEDURE During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this possible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1946

By Mark E. Emerson

INTRODUCTION A long time has passed since geologists encountered encouraging mineralization in their regional exploration program for base metals deposits. Detailed drilling during the following two field seasons served to delineate the configuration of the deposit. Various statistical techniques were employed to provide confidence levels regarding the extent of the reserves and to categorize them according to whether proved, indicated or inferred. At this juncture, it appears that the company has an orebody. Time elapsed? - three years; money spent? - $2.5 million. Much remains to be done before the orebody becomes a mine. The company urgently needs to develop new orebodies to replace its existing mines which are being depleted. It therefore has expended sizable amounts in exploration, the life blood of the company. A staff of specialists is maintained to evaluate new projects and to conduct feasibility studies. The scale of new mining projects today is beyond the resources of most mining companies. Bank financing, therefore, is often vital if the company is to survive. The following scenario describes how a company goes about evaluating mine projects and what is needed to meet lender's criteria in securing the needed financing. MINE PLANNING Now that the company engineers have taken over the project, their concern is no longer with finding ore but in developing it. An exploration shaft has been put down and a tunnel driven into the orebody to verify, on a large scale, what has been seen so far only in pencil- like drill cores. A large tonnage bulk sample is mined and shipped off to an independent metallurgical process laboratory for beneficiation testing. The budget is expended to cover engineering studies. Preliminary capical and operating costs are developed in- house and profitability studies are made based or1 assumptions concerning the markets for the main product and the indicated gold, silver, and other by-products. Time elapsed? - four years; cost to date? - $3.5-$4.5 million. The staff prepares its own pre-feasibility study. After review, the Executive Committee authorizes management to proceed with full-scale studies. The task is to make preliminary designs and to develop definitive capital and operating cost estimates. Specialized consultants will be engaged to study slope stability for the open pit and rock strength if underground recovery proves more feasible. If it is near the sea, an oceanographic report might be commissioned to see if the tailings can be disposed of off shore. Environmental impact studies are commissioned from a firm familiar with government requirements and regulations in this important area. The company subscribes for an expensive multi-client study of the supply- demand-price outlook for the product to support its own long-range price forecast. Now all the numbers are available to make a definitive appraisal of the value of the project. Cash flow analyses and sensitivity studies follow. Reams of computer printouts are generated. Time elapsed: five years. Amount spent? - up to $9 million, depending on the size, complexity and attractiveness of the project. Marginal projects always take longer. Finally, an engineering and construction (E&C) company is given the task of integrating and compiling all the data into a feasibility study. The results of dozens of reports, memoranda, computer printouts, and charts are boiled down to one final summary report of a few hundred pages together with conclusions and recommendations. After thoughtful review at a board meeting, the directors authorize management to proceed with detailed engineering work - provided that

Jan 1, 1985

By G. Aertsen

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J).-This excellent paper fills a gap in our Transactions and is most acceptable. In the early days another way of casting tire ingots, sometimes called cheeses, because of their shape, was to use a 22-gage sheet-iron cylindrical can for each ingot of the proper size to give the weight desired. These cans were bottom cast in groups, usually of four, each can being surrounded by a heavy iron ring somewhat taller than itself the top of the can being covered by a circular cast-iron plate having a small conical riser in the center, about 2 ½ in. in diameter at the bottom and 10 in. high. The top plate was clamped down to resist the upward pressure of the fluid metal and the space between the can and the outer ring, usually about 2 in. wide, was filled with dry sand. The riser permitted the escape of some of the air displaced by the steel and also increased the pressure in the steel when the mold was filled, and so diminished somewhat the tendency for gas holes to form. But little was known of segregation and pipe in those days, though the center of an ingot was understood to be the worst part, and it was separated in part in the disk which was punched out in perforating the ingot. This disk was about 8 in. in diameter and from ¾ to 2 in. thick, the variation in thickness being to rectify the weight. When an ingot was too -heavy, a thicker disk-was made by not driving the punch in quite as far as when the ingot-weight was right. Then the bloom was turned over and the punch driven in on the other side, which finished the punching and detached the disk. The tire bloom was then" becked" and later reheated and rolled as described in the paper. The forging was done with a 10-ton double-acting steam hammer. The steel generally speaking had lower carbon, from 0.45 to 0.55 per cent., than tires today have, and the tires were smaller, the most common size of ingot weighing 1,060 lb. each. BRADLEY STOUGHTON, New York, N. Y.-This paper was specially requested by the Iron and Steel Committee, because that Committee thought so important an industry should have its history written by one who was familiar with it, and before he had forgotten, or all the rest of the world had forgotten, its early stages. Mr. Aertsen has said that it is not an exhaustive research. I think it would not be any different if it were an exhaustive research, because our library made a careful attempt to find some written light on the history of these tires, but very little was found.

Jan 4, 1917

By H. R. Hendricks

THE ore of the Iron King Mine, being very hard and having a very fine crystalline structure, presents many problems in milling that are not present in ordinary lead-zinc ores. This very fine crystallization causes much interlocking of minerals and is most prevalent between the gold and pyrite and the sphalerite and pyrite. The recovery of gold is extremely important in the economic value of the ore and therefore constitutes a large part of the metallurgical problem to be solved. All of the gold is free but it has not been observed in any of the mill products except under very high magnification. Some of the gold is tarnished, and this condition also makes recovery difficult. The gold values have been determined to be highest in association with chalchopyrite and arsenopyrite. The silver occurs mostly in association with galena and tennantite. A small amount of native silver has also been observed occasionally. The galena, being softer than the other minerals, frees much better in grinding. Some oxidation of galena is present in the ore, as the nonsulphide lead content amounts to approximately 10 pct of the total lead. Some oxidation of sphalerite is also present in the ore. Microscopic examination of the zinc concentrate shows many grains in the minus 325-mesh to be half pyrite, together with the fact that some of the zinc is marmatite, makes production of a high-grade zinc concentrate very difficult unless recovery is sacrificed. In the grinding, it has been determined that the flotation feed must be maintained at 85 pct minus 200-mesh to free the minerals sufficiently to make the best economic recoveries. Table I illustrates the effect of fine grinding. It shows that the bulk of the recovered minerals is in the minus 325-mesh size and is the part of the minerals that is more readily freed. The pyrite concentrate is not given in the table because it contains practically no minus 325-mesh. DEVELOPMENT OF PRESENT FLOWSHEET AND MILLING PRACTICE The first milling operation started in 1938, with a mill capacity of 140 tons daily, producing a bulk gold-silver-lead concentrate. After several stages of expansion and changes of the mill flowsheet, the mill is currently treating 380 tons of ore daily and three separate concentrates are produced. In order of their importance and value, these are: (1) lead concentrate, (2) zinc concentrate and (3) pyrite concentrate. The present average grade of mill heads is: gold 0.11 oz, silver 4.00 oz, lead 2.50 pct, zinc 7.60 pct, copper 0.22 pct, iron 22 pet and 30 pct insolubles. Specific gravity of the ore is 3.8. During the period when bulk flotation was practiced, the flowsheet was very simple. The ore was ground fine enough to liberate as much gold, silver and lead as possible. Necessary collectors and frothers were added in sufficient quantity

Jan 1, 1947

By C. H. Mahoney, P. E. LeGrand, A. L. Tarr

MAGNESIUM, it is now generally realized, differs in some important aspects from most other structural metals, not excepting even its close neighbors, the aluminum-base alloys. This is particularly true with respect to the effects of elevated temperatures on the two light metals when in the molten state. Aluminum, on the one hand, should not be raised above its melting point any higher than is absolutely necessary if one is to avoid danger of gas absorption and a tendency toward grain growth in the resultant casting.1 Magnesium alloys, in sharp contrast, actually benefit by being heated to temperatures considerably above their melting point. It is a commonly accepted practice to establish the desired fine grain in the industrial magnesium alloys of the aluminum-bearing group by raising the temperature of the melt after the refining treatment to some 25e C (482°F.) above the melting range. To recall briefly the typical practice for magnesium alloys, the molten metal is refined by fluxing at about 730° C. (1350 F.), and after the melt has been covered with a suitable flux, the temperature is raised to between 870°C. (1600°F.) and 930°C. (I700°F.). It is then cooled as quickly as possible to the casting temperature. This superheating, as it is called, results in a fine-grained cast metal structure which has superior mechanical properties, enhanced amenability to solution heat-treatment, and better machinability than cast metal that has not been superheated. The minimum temperature of superheating varies to some extent with the composition of the alloys to be treated and usually increases with the percentage of magnesium in alloys containing the same constituent metals.2 It should be noted that the grain-refining effect of superheating is markedly apparent only in connection with the alloys containing aluminum as an alloying constituent-the binary alloy containing r.5 per cent manganese, for example, is not refined in grain to any noticeable extent by a superheating effort. While the phenomenon of superheating is well known in the magnesium industry, the mechanism of the process has remained a mystery. During the superheating cycle something occurs that forces a fine grain upon the solidifying metal. The process has been controlled in an empirical manner, and occasionally, especially on large-scale melts, and for no apparent cause, no grain refinement is obtained from a superheating treatment. Only a few papers of importance have been published on the subject. Of these, one of the most helpful is the paper by Achenbach, Nipper and Piwowarski,3 which gives considerable data concerning the effect of superheating on various properties such as fluidity, shrinkage and hot crack formation, as well as grain size, and a discussion without any definite conclusions on the theoretical aspects of superheating. A short article by Murphy, Wells and

Jan 1, 1945

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981