Search Documents

By W. A. Backofen, D. Lee

Titanium of commercial purity (RC-70) and two all-a (hcp) alloys (4Al-1/4O2 and 5Al-2.5Sn) were tested in sheet form under conditions of combined-stress loading. Plane-strain compression and plane -strain tension together with uniaxial compression and tension provided information for constructing the tension-tension and compression-compression quadvants of the plane-stress yield locus. Coordinate values were obtained from yield-strength measurements; the slope at each point was based on a plastic-strain ratio. The materials represented a wide range of plastic anisotropy, which was reflected in correspondingly varied departures of the yield locus from that for iso-tropy. The tension-tension and compression-compression quadrants were not identical. If the uniaxial yield strength is insensitive to direction and the sign of the applied stress, the Mises or perhaps the Tresca criterion is adequate for predicting the onset of yielding under combined-stress loading. The prediction is not so straightforward in plastically anisotropic material. Depending upon details of texture, combined-stress yielding resistance may be substantially different from that indicated by the usual criteria.' However. a continuum theory of yielding under such conditions is available for reasonably direct application.2,3 Whether or not it can be used successfully must, of course, depend upon how closely the conditions of the theory are satisfied in the material in question. In its present form the theory contains no provision for Bauschinger-type effects, nor does it allow for the consequences that might grow out of deformation by more than one mechanism, e.g., by slip and twinning.4 With those limitations, more importance must be attached to experimental information about the yield surface for anisotropic materials. Studies of the yield surface have generally been confined to states of plane stress (tension-tension and tension-compression) established in thin-wall tubes by externally applied forces and internal pressure. That approach would be entirely suitable for anisotropic materials if they were available in tube form or in sufficient bulk to be machined into test specimens. 6-9 It would not serve for the textured and anisotropic sheets of much current engineering interest, unless sheet could be formed into high-pressure tubing without structural change. Since there would seem to be little chance of the latter, practical alternatives are needed. One such alternative is the subject of this paper. It involves the use of a few selected but relatively simple uniaxial loading tests on sheet specimens. The underlying idea is presented here with some details relating to application and a few results bearing on how well it has worked. THE BASIS OF TESTING Conventional Measurements. Yielding for a general case of anisotropy is described by the plane-stress locus in Fig. 1. Reference directions in the sheet specimen are related to the stress coordinates as shown with the insert: x is the rolling direction, y the transverse direction, and z the through-thickness direction. The four reference-direction yield strengths (t, tension; c, compression), Xt, Xc, Yt, and Yc, are all different. Nine paths that can be followed in uniaxial loading experiments are identified. Paths 1, 2, 3, and 4 represent conventional tension and compression testing to establish Xt, Yt,.Xc, and Yc. Useful information also comes from the ratio of the transverse plastic-strain components associated with yielding and flow in conventional tension or compression. A condition to be satisfied in locus construction is that the plastic-strain vector be everywhere normal to the locus.10 The projection of the vector which would

Jan 1, 1967

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By T. C. Craig

During the year, there were 570 oil wells completed for a total daily initial production of 365,352 bbl. The daily oil potential of the field, effective Jan. 1, 1935, as established by the Texas Railroad Commission, was 306,102 bbl. with a daily allowable of 58,800 bbl., whereas, on Dec. 31, 1935, the potential was 587,376 bbl. with a daily allowable of 57,800 bbl. Because of the limited market demand, the allowable decreased although the potential increased. In August, the five-day test for determining the potential production of a well was replaced by a 24-hr. test. The reason for this change was that some of the oil-pur-chasing companies contended that too much oil in excess of the limited market demand was produced during the five-day tests. Dry Gas.—During July, the Texas Railroad Commission supervised the first complete and accurate field-wide test of open flows that has been made in this area. The total open flow as determined at that time was 16,426,085,000 cu. ft, There were 79 gas wells drilled in '935, with a combined open flow of 2,408,000,000 cu. ft. and 50 depleted oil wells were plugged back for gas with a total open flow of 529,800,000 cu. ft. The total new gas production for the year was, therefore, 2,937,800,000 cu. ft. The 17 natural-gas pipe lines drawing on the Panhandle supply of fuel gas withdrew a daily average of 420,497,507 cu. ft., or a total of 153,481,-590,000 cu. ft. for the year. The 44th Texas Legislature passed a statute known as House Bill No. 266, which was designed to prohibit waste and protect correlative rights by compelling the ratable production of gas. The part of the law relative to withdrawal of sweet gas became effective Aug. 1, 1935, and the part referring to withdrawal of sour gas became effective Oct. 1, 1935. Three of the major pipe line companies attacked the validity of the ratable production feature of the new law and a preliminary injunction was granted by the Federal District Court. The final hearing on the incrits of the case is scheduled for the early part of January. Natural Gasoline.—Forty of the 42 natural-gasoline extraction plants in the Panhandle operated throughout the year. One plant discontinued

Jan 1, 1936

By Fred Witt, Milton Schwartz

ESTABLISHED methods for obtaining quantitative pole figures for flat sheets1"5 can be extended to apply to thin films on a substrate. The mode of scanning the sample is exactly the same as described in the references? but consideration is given to the fact that the scattered X-ray intensities are due to both the thin film and its substrate with appropriate attenuation factors. The purpose of this paper is to describe a method to obtain the scattered intensities from the film alone for subsequent pole-figure determinations. Fig. 1 shows the four possible general positions of the film (f) and its substrate (s) with respect to the incident X-ray beam (I,). In this paper it will be assumed that the plane of the sample is normal to the plane of the diffractometer. In the diagrams the line jV is the normal to the flat sample and the line P is the trace of the diffracting crystallographic planes in the plane of the diffractometer. The angle of tilt, a, is the positive acute angle measured from the line N to the line P; if this angle is measured clockwise then a is said to be in the positive a region; if this angle is measured counterclockwise then a is said to be in the negative a region. For the reflection cases, the total scattered intensity, at the proper Bragg angle for a particular set of planes, is due to that scattered by the film Vf) and that scattered by the substrate. The beam incident on

Jan 1, 1967

HAVING already shown you the methods of making the moulds for casting and how they are to be prepared so that they may receive the melted metals well, it is now necessary, in order to complete the casting with perfection, that I show you not only the operations and instruments by which metals are softened, but also how metals can be made as liquid and fluid as water so they may easily enter into all the hollows of the moulds that you have made. Of these, besides the fire which is the prime agent, there is a very powerful furnace, which is called a reverberator.* I believe this is chosen not only for convenience but also because it is necessary in large casts. This is made of baked bricks, or of crude ones if desired or of suitable fire-resistant stones. Although all masters have the same objective, each one proceeds to make this kind of furnace according to his own ideas so that it can be said that there are almost as many different shapes of such furnaces as there are masters. This can be seen in the place that contains the metal, which is of such a shape that the force of the fire may operate better. Thus some masters are called good who, seeing no farther than what has been shown them, make them circular like a bread oven. Some others make them oval across the fire en- trance, while others extend them lengthwise. Also, there are some who make a single outlet for the flames, some two, and some three. Some make the entrance for the fire high and narrow and others, wide and low. The same is true of the place where the flames are generated, which is called the firebox. Some put the wood in from the side, some lengthwise in the same direction as the entrance for the flames, and some from above by means of a little hole. Also, one makes the vault low, and another makes it high. And while one puts an entrance for air underneath so that the

Jan 1, 1942

By A.A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

By A. A. Gustafson

In diamond or churn drilling for the prospecting of ore bodies, two products can be used for quantitative analyses; i.e., the core and the cuttings, or sludge. Some operators prefer an assay of core; others insist that the sludge be sent for analysis. Both must recover the sludge for check samples or for assays if there is no core recovery for any particular section of the diamond-drill hole. The Freeport Sulphur Co. found that numerous cumbersome sludge boxes or barrels were inconvenient and delayed drilling. The sludge settled slowly in the ordinary shallow, rectangular diamond-drill boxes and its total removal from the container was difficult, time-consuming and unsatisfactory; and sampling of deposits of which the metal contents are easily concentrated, as in ores containing cinnabar, gold and silver, is subject to error if the boxes are not thoroughly cleaned. Mr. Charles Ballard, dredge superintendent at Freeport's operation at Grande Ecaille, Louisiana, developed a portable cone while he was in charge of prospecting a mercury property near Tonopah, Nevada, in 1940. Ballard later improved the design while the settler was being used at a manganese property in New Mexico. The operation is based on the "free settling" of comminuted particles in a quiescent liquid. The ordinary sludge box discharges over a lip 8 to 12 in. wide and consequently the water has sufficient velocity so that the discharge water is never clear. The cone settler used by Free-port Sulphur Co. discharges over the entire circumference, which gives a discharge ltp of 9 ft. in the size of cone used at the cinnabar and manganese prospects. Consequently, the velocity of the discharge water is slow enough so that all fine material settles and the discharge water is clear. When the drilling of a sample interval is complete, the sludge can be drawn off by the time the driller is ready to cut another sample. Thus, only one cone is needed per drill. The cone has been used by Freeport successfully in churn-drilling a manganese deposit, in diamond-drilling a mercury deposit, and in diamond-drilling a deposit of ore containing tin, copper, gold and silver. The cone is greatly superior to the old methods of collecting sludge and is now used on all Freeport drilling campaigns in the western states, both for surface and underground drilling. Fig. I shows the important details of a cone designed for average operating conditions, 30 in. in diameter and 36 in. high. Abnormal conditions may require some revisions in design. Fig. 2 shows a working drawing. A hose or pipe larger than the one used to convey water from the pump to the swivel head of the string of rods is connected to the stuffing box at the collar of a diamond-drill hole, The usual T-connection is used. It is not necessary to use a stuffing box if the top of the cone can be placed lower than the collar of the hole. Then the return water and cuttings can be made to flow by gravity. This hose or pipe discharges the cuttings of the drill bit and the return

Jan 1, 1943

J. M. TIPPETT? Colorado Springs, Co1o.-There are several points which offer ground for discussion, although the authors' indicated results leave small chance for argument. Under classification of the ores as they come to the mill, it will be noted that these are classified according to their lime contents. In previous years the classification was based upon sulfur contents, CaO not being considered; class A would be called the oxidized ore and class B the sulfides. Classification according to CaO is the first public indication that a decided change in the ore has necessitated improved methods of treatment. The very serious effect that CaO, even in small quantities, has upon extraction has been noted for some years.

Jan 11, 1918

By R. V. Ramani, George W. Luxbacher

Computer simulation of mine ventilation systems, after a slow start in the early sixties, is gaining increasing acceptance for planning, design, and evaluation purposes. Numerous programs are readily available from government, university, consulting, and industry sources. The computer adage "garbage in, garbage out" is as applicable in ventilation engineering as in any other application of computers, and has been responsible for the questionable results obtained in some instances. The source of input data for a ventilation simulation is most often a pressure-quantity survey of the mine, or, in the case of a new mine, information derived from a survey of an existing mine which has conditions similar to those expected in the new mine. The crucial step is to generate simulation input data from the ventilation survey. Problems such as quantities that do not balance, pressure gradients opposite to measured air flow, differences in the pressure datum in a multi-shaft mine, modeling of leakage, and deviations in flow from the square law (H=RQ2) are frequently encountered and must be resolved. The purpose of this paper is to discuss these aspects and to propose procedures which can lead to input data for valid simulations of mine ventilation systems.

Jan 1, 1982

By Charles George, Ronald Faul

The cementing process has been used in approximately 2.5 million oil and gas wells to seal, protect and isolate various downhole formations against communication. It has been adapted to other more specialized situations such as solution mining and sealing salt storage reservoirs. The technical literature contains very few papers specifically dealing with the cementing process for these applications, yet there have been many special projects in various parts of the world that are novel. These will be highlighted in this review. This paper also presents a comprehensive review of the various techniques used in cementing wells drilled for the recovery of soluble salts and brines. It also covers the application of cementing techniques to a large number of wells drilled for the storage of hydrocarbons in South Louisiana.

Jan 1, 1985

By Robert M. Lewis

Silica sand deposits are usually contaminated with various heavy minerals which must be removed to make the silica useful for flat-glass production. Research was undertaken to develop a better procedure for producing flat-glass-grade silica. Batch tests revealed that anionic detergent-type reagents had considerable promise. Pilot plant tests were run to compare the effectiveness of anionic detergent-type reagents with petroleum sulfonate in the removal of heavy minerals from a potential glass sand. Another slightly modified commercial procedure also was evaluated for comparison. In the pilot plant trials, utilization of the anionic detergent potation reagents did not produce quite as good results as petroleum sulfonate. It is likely that flat glass-grade sand could be produced with the anionic detergent reagents if more extensive pilot plant tests were conducted.

Jan 1, 1977

The October issues* of the Journals of the three AIME Societies carried a brief resume of the historical development of various technical and professional organizations which in some immediate or remote way affect the individual member of AIME. This resume was presented by the Institute Committee on Inter-Engineering Society Cooperation. Recently, several plans have evolved designed as a first step to provide a so-called "unity organization" for the entire engineering profession. Almost all of the plans involve Engineers' Joint Council, Engineers' Council for Professional Development, and National Society for Professional Engineers in some way or other. Hence our committee is presenting to our membership a resume of the recent activities of the two umbrella organizations and of NSPE. More detailed information on any of these organizations may be obtained from annual reports published by the organizations.

Jan 2, 1961

By J. H. East, E. R. Maize

Probably no other type of equipment is now being introduced into American underground mines about which less is known and about which there is more misinformation than the Diesel mine locomotive. Any equipment installed underground brings with it hazards that were not present before, and it is the purpose of this paper to show that Diesel-powered equipment can be used with safety in underground mining if certain feasible but very important precautions are taken. Diesel locomotives are not new in underground mining, since they have been used successfully in European mines for at least 19 years, but their use in American mines is exceedingly limited; so far as is known, only five Diesel mine locomotives are operating at present in United States mines. Diesel locomotives were permitted underground in Great Britain for the first time in 1939, and the rapid increase in the number in use in those mines testifies to their safety and efficiency. More than 1300 Diesel mine locomotives are in use in European mines, according to the latest statistics; these locomotives are employed in coal, iron, lead-zinc and mercury mines. SO far as is known, the Diesel mine locomotive has not yet caused an explosion or mine fire, and has not been the cause of any fatalities from toxic gases in the mines in which it has been used. Adjustments of Diesel Engines foR Underground Use A Diesel engine adjusted to work in an underground mine should not be confused with the same engine adjusted for use outside the mine. Adjustment of the air:fuel ratio for engines that are used on the surface is intended to give the maximum fuel economy, and little or no attention is given to the chemical composition of the exhaust gas produced. Many such engines are poorly adjusted and perhaps poorly maintained, with the result that the engine emits smoke in quantity as well as the disagreeable odor familiarly associated with Diesel engines. The air:fuel ratio in the case of Diesel engines operated on the surface is generally around 15:1; that is, 15 lb of air to burn I lb of fuel. Diesel engines adjusted to work underground usually have an air:fuel ratio of about 20:1, as at this ratio the minimum quantity of toxic gases is given off in the engine exhaust. Diesel engines operated underground must be maintained in better condition than similar engines used on the surface; otherwise, the smoke emitted in the exhaust becomes objectionable if not unendurable. Practically normal air is required for safe operation of Diesel engines underground or in confined places; failure to provide virtually normal air for Diesel engine operation is almost certain to result in trouble. Bureau of Mines engineers have determined that the air in which a Dicsel Operates hi confined places should contain less than % pct of carbon dioxide and at least 20 pct of

Jan 1, 1949

By C. D. Michaelson

Bridging the gap between have and have-not nations is one of the necessities of the present era. The responsibility for accomplishing this must be assumed by the affluent industrial societies of the world, both through their governments and through private enterprise. Despite a discouraging number of instances where companies established in underdeveloped countries have been expropriated, U.S. industry must not abandon such ventures. Instead, it should tailor them to the needs and aspirations of the host nations. One way in which industry can minimize the danger of expropnation is to enter into partnership with the government of the host nation. Kennecott Copper has recently done this in Chile, becoming 49% owner of a company formed to expand and operate the El Teniente mine. So far, the partnership has produced marked benefits not only for Chile, but also for Kennecott. The memory of D.C. Jackling serves chiefly to remind us how much we owe to the pioneers of our industry. Jackling was one of the giants. Orphaned at the age of two, he made his way through sheer persistence and plain hard work. His brilliance gave rise to a vision, and his tenacity made his vision a reality. Foreseeing that economies of scale would make the handling of low-grade ore profitable, he introduced the revolutionary concept of open-pit copper mining. During World War I, the defense effort of the United States was irnrneasurably strengthened by the tremendous supplies of copper from the western mines that Jackling had made possible. Again in World War 11, the demands for copper were supplied, and the nation once more had profound reason to be grateful to this rugged, stubborn man who had long ago ventured into the mountains and unlocked their wealth. We are now embarked upon another great era of change, and we must devise new concepts to meet it. The task is not only to create new techniques of mining, but to forge better ties between men and institutions which will let us work in harmony with the techniques we have. We might recall that while Jackling was a man of towering pride and formidable will, he was also adept at getting others to share his vision and join his purpose. Today our reach for cooperative endeavor must go far beyond our own shores as we seek to develop the buried riches of distant lands. And we would do well to remember that Jackling's remarkable insight would have come to nothing had not British investors been willing to provide much of the initial capital. As was true of so many early enterprises in America, European capital was absolutely essential. CORPORATIONS ABROAD - AN EXPANDING ROLE Today the situation is quite different. The United States is now a capital-surpIus nation and looks abroad for opportunities to employ its capital profitably. On the other hand, we have become dependent on foreign sources for supplies of vital raw materials, while we seek

Jan 1, 1970

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By S. Maemura

Miike Colliery of Mitsui Coal Mining Company, the biggest and oldest coal mine in Japan, is producing a quarter of the national coal production, about 5.2 million tons of clean coal annually and almost a half of which is now being mined under the "slicing Mining System". The slicing system is a mining method to mine a thick coal seam dividing it into two faces, upper and lower. Its history started nearly 20 years ago. However, the all-around modernization of this system has made little progress up to recent years, while mining methods for single longwall faces has made a remarkable progress together with the improvements in mining machineries, self advancing supports and so on. The reason was that the tremendous difference in adaptabilities of mechanized face equipments existing between the upper and lower faces has made it very difficult to increase the total production capacity of slicing system. After our persistent study for seventeen years, we have recently realized successfully the quite satisfactory slicing system, applying the combination of shield type self advancing supports and double ranging drum cutter at both faces. We are now fully convinced of that the high efficient, quite safe and improved slicing system has been basically established for the present. This paper intends to brief the transition on the combination of self advancing supports and mining machines, its results and further to detail the development of shield type self advancing support for upper face and artificial roof material which shall be the key point to be successful in full mechanization of slicing faces.

Jan 1, 1976

By D. J. Carney, J. Chipman, N. J. Grant

SINCE the beginning of this century it has been known that hydrogen contributes to the porosity of steel and that it is harmful to its mechanical properties. The evidence for this has been largely qualitative. Steel to which hydrogen was purposely added. in sufficient .amounts was shown to be either porous or brittle or both, whereas similar steel of low hydrogen content was shown to be free of porosity and to possess normal physical properties. There have been a considerable number of qualitative experiments of this type. Also, early in this century, a few attempts were made to measure the amount of hydrogen normally dissolved in commercial steels. This was usually done by placing the sample under an inverted liquid column such as mercury and collecting the evolved gas. These attempts, while not successful in measuring actual amounts of dissolved hydrogen gas, were able to prove that this gas will diffuse out of steel at room temperature, and that the amount of hydrogen dissolved is normally very small. On the basis of such qualitative evidence, hydrogen has been and still is blamed for a great number of the troubles encountered in the steel industry. In recent years, partial solutions for many steel-working problems have been obtained. These have led to increased interest in accurate quantitative work on hydrogen in steel, with the expectation that the results might possibly answer a few of the remaining unsolved problems. Commercially, two of the obvious questions which are in need of an answer are: (1) what are the most important sources of hydrogen, and (2) what quantity of hydrogen can be tolerated in various steels? There are many other unanswered questions. To begin to find the answers it seemed logical to start at the beginning of steel production with the liquid metal. Further, it seemed almost imperative to solve first the problems of analysis and sampling of the metal for hydrogen. Once these problems have been solved, it would be possible to answer more of the important commercial problems mentioned above. As a consequence, it was decided to design an analytical apparatus and, upon satisfactory completion of this, to develop an accurate method of sampling liquid metal for hydrogen.

Jan 1, 1951

By J. J. Tietjen, D. Richman

Single-crystal Gap lms been epitaxially grow from the vapor phase at a rate oJ 3 p per nzin without encountering a7Zy low-ang-le grain boundaries or debwading- the electrical properties of the material. This growth rate exceeds any value previol~sly reported for the vapor phase growth of Gap. In pure material, mObilities ns high as 175 sq cm per U-sec at room tenzperature and 1450 sq cm per v-sec at 77°K have been obtained. These values are anLong the highest that have been attai)led for this material. For the first time, Gap possesses a number of important properties which make it well-suited for use in electro-optic modulators. First, the transverse electro-optic effect is operable in this material, which makes it possible to increase the path length of the modulated iron doping of Gap has been achieved; this results i?z resistivities of approximately 10" ohm-cm. The problelrls of residual strain and isolated shorting paths in these crystals have been partially solved. Electro-optic modulation of visible radiation has been demonstrated with this material. It is anticipated that further improvement with regard to the probleins of strain and shorting paths will result in a practical Gap electro-optic modulator. radiation without increasing the applied voltage. In addition, this permits the use of thin crystals so that relatively small voltages are needed to provide the requisite high electric fields. Second, GaP is a cubic crystal and therefore does not introduce critical optical-alignment problems associated with birefrin-gent crystals, such as ammonium dihydrogen phosphate (ADP), and potassium dihydrogen phosphate

Jan 1, 1968

By Rush N. Hosler

This paper was prepared for the purpose of answering some of the many questions as to why, in the construction of Pennsylvania's Coal Mine Schedule Rating Plan, various factors were, or were not, taken into consideration. Much has been written about merit and schedule rating of industrial risks from an actuarial viewpoint, therefore this phase of the question is taken up only so far as may be necessary in presenting the practical application of the plan now in use. Companies writing fire insurance, about 30 years ago, were the first branch of insurance to use schedule rating; the values assigned their items were largely a matter of judgment. In 1913, the Industrial Commission of Wisconsin evolved the first schedule rating plan to be applied to industrial risks under compensation insurance. Pennsylvania, in 1916, with the inception of its Compensation Act, was the first state to apply the principles of schedule rating to coal mines. A definition of the term "schedule rating" submitted by the writer in a brief to the Safety Committee of the United States Coal Commission is as follows: Schedule rating, as applied to compensation insurance, is an instrument to measure the hazard of known causes of accidents to which employees are exposed in industry and thereby determine an insurance rate commensurate with said hazard. It was first applied to Coal Mining in 1916 in Pennsylvania.' In other words, for a mine operator to insure his employees for injury under the Workmen's Compensation Act, it is necessary that he pay a certain premium based on his payroll. If all mines were assessed the same premium, it would be unfair for the mine with low natural hazard, good safety conditions, and good accident experience to pay the same premium as a mine with bad conditions and experience, therefore schedule rating was introduced.2

Jan 1, 1925