Search Documents

By R. V. Smith

The theory for unsteady radial flow of gas, as simplified by Aronofsky and Jenkins, has been reviewed and compared with actual well performance. This study indicated that the theory should be modified by the introduction of an empirical "rate of flow" function "Y(q)". The expansion of the theory on the flow of gas to include a Y(q) term bridges the gap between the theory of unsteady-state flow of gas and actual gas-well behavior. Apparently, the Y(q) term is a function only of the rate of flow for a given well. The completion factor or skin effect is associated with the Y(q) function in such a manner that at least two or more sets of drawdown or pressure build-up tests are needed to separate the Y(q) function and the completion factor. Since the Y(q) function used in this report represents an energy loss dependent on rate of flow near the well-bore of a gas well which is in addition to the loss required by Darcy's law, the Y(q) function is related to the exponent of the back-pressure curve for a gas well. Techniques and equations are presented which permit the estimation of stabilized and "short-time" deliver-abilities. INTRODUCTION The published theory of radial unsteady-state flow of gas through porous media may be divided into papers1-" which use Darcy's law as a premise and other papers4-7,16-10 which recognize that Darcy's law may not hold for flow into gas wells. Miller8 compared theory based on Darcy's law with actual gas-well behavior and concluded that flow into gas wells deviates from Darcy's law. Houpeurt4,5 in a thorough investigation of flow into gas wells concluded that the flow rate into a gas well is proportional to the difference between the squares of upstream and downstream pressures elevated to a power between 1.0 and 0.5. Houpeurt also concluded that the deviation from Darcy's law is caused by irreversible, kinetic energy exchange between the flowing gas and the porous media. Tek9 presented a complete evaluation of the flow problem in gas wells. Several investigators state that the inclusion of gas compressibility into flow equations based on Darcy's law does not begin to explain the flow problems suggested by gas-well behavior. For many years, natural-gas engineers have realized that gas wells by actual test exhibit behavior which cannot be explained entirely by Darcy's law. Many tests on gas wells have indicated that a value of 0.85 for the exponent in the back-pressure equation is a fair average for many wells. However, Darcy's law either for steady or unsteady-state conditions indicates that the exponent should be 1.0. The purpose of this paper has been to examine this deviation from Darcy's law and to present a reasonable mathematical means of evaluating the deviation. The method presented in this paper combines previous theory with an empirical function to provide a description of gas-well behavior. All equations in this report are for constant terminal-rate-of-flow conditions. While present methods of testing wells usually are not based on this concept, they are believed to approach the constant terminal-rate conditions closely in many tests. However, several gas wells were tested by holding the rates of flow constant in order to approach more closely the constant terminal rate of flow; the results confirm the concepts presented in this paper. REVIEW OF THEORY FOR UNSTEADY-STATE FLOW OF GAS The basic partial differential equation for the flow of natural gas has been given in technical literature; the equation for a cylindrical reservoir with the well in the center is

By T. D. Mueller, F. C. Miller, Jr. Earlougher R. C.

In analyzing pressure buildup tests for field wells producing both oil and gas, the common practice is to use a modification of single-phase flow theory. Validity of such an approximation has been demonstrated for single-well solution-gas-drive systems. This paper indicates that such approximations are also valid for two-well solution-gas'-drive systems. From this it is inferred that the technique can be used for multiple-well systems. A computer was used to simulate the behavior of a two-well solution-gas-drive reservoir to test the validity of the above type of analysis. Simulation results indicate that pressure buildup tests in such a system can be analyzed within engineering accuracy for formation permeability and pressure. A rule of thumb is given for estimating the length of time a well must be shut in for the pressure in a nearby producing well to increase significantly. To observe such an increase, the shut-in well would have to be left shut in much longer than normal. INTRODUCTION An important technique for obtaining data concerning a producing petroleum reservoir is the pressure buildup test. Such a test, when properly conducted and analyzed, provides information on the average reservoir pressure and the permeability in the major drainage area of a well. The theory upon which the analysis of a pressure buildup test is based assumes that the behavior of the fluid in the reservoir is adequately described by the diffusivity equation.1 Use of the diffusivity equation implies that a single fluid of small and constant compressibility is flowing. To analyze a pressure buildup test in situations which involve more than one fluid phase, the single-fluid analysis is extended. This paper verifies the extension of pressure buildup analyses to two-phase, two-well systems. Miller, Dyes and Hutchinson1 have presented a technique for analyzing pressure buildup tests in circular bounded reservoirs. Their method requires that the reservoir be producing at pseudo-steady state (constant pressure gradients) prior to shut-in. An alternate reservoir model, presented by Horner,2 assumes that the reservoir is infinite. The Homer model does not assume a Pseudo-steady state prior to shut-in, but the assumption that the reservoir is infinite implies that the average pressure can be determined only if the total production prior to shut-in is small compared to the total fluid originally present. Limitations imposed by the pseudo-steady state and infinite reservoir assumptions are avoided by the technique proposed by Matthews, Brons and Hazebroek.3 Their method can be used to calculate both the Permeability and the average pressure in bounded single-well systems which are not necessarily at steady state. They also suggested determining the average pressure of a multi-well reservoir producing from pseudo-steady state by volumetrically averaging the static pressures of the individual wells. Matthews and Lefkovits4 used numerical simulation techniques to verify that this method does produce adequate results for single-phase, multiple-well systems. Perrine5 proposed modifications to the single-phase theory so that pressure buildup tests in multiple-phase systems could be analyzed. He suggested replacing the single-phase mobility (k/µ) by the sum of the mobilities of the individual phases, and replacing the fluid compressibility by an average compressibility weighted by the saturations of the separate phases. By using numerical techniques to solve the two-phase flow problem for a single-well system, he concluded that this approximation gives results within engineering accuracy. More recently, Weller6 has shown that, for a gas-oil system with a single well at the center of a circular reservoir, pressure buildup tests can be analyzed adequately by using the modification proposed by Perrine. Feller's results also indicate that, as the gas saturation increases, this analysis becomes less accurate. To date, no evidence is available to show that the Perrine approximations can be combined with the Matthews-Brons-Hazebroek technique to calculate the average pressure of a multi-well,

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

By C. van der Poel, R. L. Chuoke P. van Meurs

When an initially planar interface between two im-ttitcihle liquids is displaced at constant rate, U, nor-mat to the front, instability will occur for all rates greater than a critical rate. U, given by provided the Fourier decomposition of the spatial pertmrbcrtiott or deformation of the moving displacetment front contains modes with wavelengths. A, greater than a critical wavelength, given by tit there expressions, p, p and k, with the subscripts I and 2 distinguishing the two 1iquids under consideration, are density, viscosity and effective pemeability coefficients respectively; g is the absolute value of the acceleration due to gravity; and cos (zz') is the direction cosit7e between the vertical carlesian coordinate z' (positive upward) and the z coordinate norma1 to the initially plane macroscopic interface taken positive in the direction from Liquid I to Liquid 2. U is the average volumetric velocity (injected volume of liquid pet. unit time per unit of area normal to Z) and is positive for Liquid I displacing Liquid 2, negative for the reversc displacement and r2 is an effective inter-fucial tension (for displacements between parrallel plates, t0= s the ordinary bulk interfacial tension). further, there is a wavelength of maximum instability given by For natural perturbations, this wavelength will preclotninate and characterize the form of the instability as a quasi-sinusoidal deformation, i.e., viscous fitzgers of peak-to-peak separatiotr, A,,. Comparison of experitient with theory rei'eals tltat these considerations are recsonably valid for displacements in hoth parallel plate chantzels and nnconsoli-clutt'd glass ptnvder packs. These results are. tij particular interest for interpretation of data from laboratory experiments with regard to fielil applica/iotz.s. It is quite possible for A,, although st7zall relative to the large lateral dimension of the reservoir, to rxceed the greatr.st lateral extent of the lahoratory sample or model. If it does, frontal displace- ment occurs in the laboratory experiments, and oil INTRODUCTION Thc puposes of this paper are to present theoretical and experimental evidence for occurrence of macroscopic instabilities in displacement of one viscous fluid by another immiscible with it through a uniform porous medium and to compare available experimental data with some predictions of a theory of instability developed by the first author. The instabilities are referred to as macroscopic in the sense that spatially quasi-sinusoidal, growing fingers of the displacing liquid are formed, the width and peak-to-peak separation (wavelength) of which is large relative to a characteristic length of the particular permeable medium such as grain size. Visual models of two kinds have been used to obtain observations: displacement of oil by water-glycerine solutions through the flow channel formed by closely spaced parallel plates and displacement of oil by water with and without initial interstitial water through unconsolidated glass powder packs, employing the technique of matching indices of refraction. In all cases we have observed macroscopic instabilities or fingers under conditions predicted by the theory to be favorable for their occurrence. The phenomenon discussed here is not the production of streamers due to gross inhomogeneities such as permeability stratification of the porous medium. It is our object to show, on the contrary, that a quantitative prediction of finger spacing is possible in a porous medium known to be macroscopically homogeneous and isotropic throughout. The importance of the phenomenon in its influence on the configuration of oil and water with respect to oil production behavior was noted earlier by Engel-berts and Klinkenberg' who coined the term "viscous fingering". THEORY Necessary and Sufficient Conditions ior Instability anc Initial Kinematics There are several levels of increasing complexity in the theoretical description of instabiIity of fluid displacements in permeable media. Of these, the simplest description, ;tdapted to low permeability systems, is selected for presentation.' More inclusivc tlescriptions are reserved for separate publication.

By W. van der Knapp

A theoretical and experimental ana1ysis is given of the change in volume of a porous medium due to changes in external and internal pressures. The result enable one to deduce directly the effect of large increlents in stresses. It is shown that the three-dimensional representation of the volume of a nonlinear porous system is a cylindrical rules surface, the generating lines of Which have a slope according to the solid rock compressibility. Analytical expression for such a ,surface is very simple. It follows that the bulk and pore compressihilities depend only on the difference between pore fluid and external hydrostatic pressure, i.e., the effective rock frame pressure. From measurements on a number of sandstones as well as limestones it can be conduded that for practical values of this effective frame pressure the pore compressibility falls in the range between the compressibility of water and that of undersaturated crude oil. In general, pore compressibility is found to be higher the lower the porosity. For a particular limestone reservoir pore compressibility and porosity could he related by means of a simple empirical formula. Results from the described study find a direct applicxtion in material balance calculations and in prob1ems of liquid flow through porous media. Since the elastic constants of the rock bulk material enter into equatiorls for velocity of acoustic waves, the results are also of importance for calculating rates of wave propagation in these media. It is shown for sandstones with 1.5 to -10 prr cent porosity that laboratory measured porosities may differ from those lender reservoir conditions by about I per cent of their value. The difference for low porosity limestotnes can be of the order of 10 per cent. The subsidence caused by elastic deformation of reservoir rock is shown to he very small. General formulas relating pore and bulk volume to external and internal pressure can be derived, as has been shown by Biot1, Gassmann2 and Geertsma.2 Their theories describe the differential change in volume caused by a variation in pore fluid tension and external hydrostatic tension. It has been known for a long timei that the stress-strain relations of a packing of spheres are essentially noninear. Our experiments show that for almost all reservoir rocks which arc elastically deformable the relation between volume and loading is also a nonlinear one, resembling that of a packing of spheres very closely. The behavior of these media is often described by using the linear stress-strain relations for small incremental stresses and strains in the vicinity of a pre-stressed condition." The present study differs from these considerations in that it enables one to deduce the effect of large increments in the stresses directly. In analogy to the stress tensor for a homogeneous body the stress tensor for a porous body can be written in the conventional way: where the tensor components, o, and t, represent the total forces acting on the faces of a unit cube of porous material. This tensor can be split into two parts. a hydrostatic and a deviatoric part, as follows2,3,1 where the component of the hydrostatic stress system, a. equals The hydrostatic stress causes a change in volume whereas the deviatoric stress system gives rise to a change in shape only. One of the difficulties in describing changes of volume occurring in reservoir rocks is that the relations connecting these volume changes with external and internal stresses are essentially non-linear. A complete description requires the bulk volume, V,,, as well as the pore volume,V,,. to be known as a function of both the changes in pore fluid tension (v) and the hydrostatic tension on the outer boundary.

By N. Jaffe, J. E. Dorn

This investigation is concerned with the possibility that the creep resistance of metals might be reduced as a result of recovery at the creep temperature when the applied stress is reduced. For this purpose the effect of stress on the recovery of the creep behavior of pure polycrys talline aluminum was investigated in the cross-slip temperature range where the activation energy for creep is 28.000 cal per mole. Before recovery all specimens were given the same substructure by creeping them under a stress of 7800psi to a strain of 0.218. Recovery was then accomplished by holding the specimens at the creep temperatures of 327" and 337°K under a series of reduced stresses for various periods of time. When the original stress was reapplied the specimens crept more rapidly than when the original stress was first removed, illustrating that recovery did take place. The extent of recovery could be indexed in terms of the UNDER certain conditions of test, the creep rate decreases over the primary stage of creep often by as much as a factor of 10~B. Since the external variables of stress and temperature are held constant, such pronounced and significant changes in the creep rate must be attributed to various substructural modifications that are introduced as a result of creep itself. At the secondary stage of creep, over which the creep rate remains constant and the substructure no longer changes, a balance must be achieved between the rate of increase in creep resistance due to creep straining and the rate of recovery of the substructural modifications. The general validity of these concepts on substructural changes has already been shown,' including the corollary that a more creep-resistant substructure is introduced under a more rapid creep rate arising from a higher applied stress.' In spite of these well-documented facts, very little progress has been additional strain undertaken by the recovered specimen to achieve the same strain rate as the unrecovered specimen. It is significant that the higher recovery stresses gave the most rapid rates of recovery. Over the high range of reduced stresses, where some creq took place during recovery, the activation energy for recovery equaled that for creep, namely 28,000 cal per mole. But for stresses during recovery below 0.80 of the original creep stress, no creep was detected during recovery and an activation energy for recovery of about 72,000 cal per mole was obtained. Whereas the activation energy of 28,000 cal per mole suggests that cross-slip of dislocations is responsible for this recovery, the mechanism for the 72,000 cal per mole process is not known. This activation energy, however, is about twice that for self-difhsion. made in determining, in satisfactory detail, precisely what substructural changes so effectively modify the creep rate.' Up to the present, electron microscopy has failed to uncover, in a satisfactory quantitative manner, the mechanistic processes involved. Since, however, creep, at least at moderate and high temperatures, arises from one or more types of dynamic recovery processes, it should be possible to shed additional light on the total problem by investigating the recovery of creep resistance. The importance of such an investigation becomes apparent when the fact is recognized that there has yet been no direct experimental proof that the rate of softening due to substructural changes as a result of recovery equals the rate of hardening due to creep-induced substructural strengthening over the secondary stages of creep. Furthermore the problem of what happens to the creep-strain induced strengthening when the material recovers either at zero or some reduced operating stress has significant engineering consequences. It was for these reasons that the present investigation on the recovery of creep behavior was initiated. Inasmuch as a substantial background has now developed on the creep of high-purity aluminum, this material was again selected for the current investigation. Furthermore extensive evidence is now

Jan 1, 1963

By B. C. Allen

Grain-boundary gvoocing was studied irz chronziu?n. molybdenum, tungsten, and the solid-solution alloys, Cr-35Re. Mo-33Re, and W-25Re at 0.6 to 0.9 of the absolute liquidus temperature under an inevt atmosphere , foveign nzetal zlapor, and liquid metal. The controlling mechanism of matter transport was deduced frolr groove size and shape. kinetics of growth, and cotnparisoz with theoretical relatiotzships derived by Mullins. Grooves in chowzizon formed prittzarily by volume diffusion tkrongk kelium or argon at 1 atm pressure and by e1)apovation-condensatiotz in a static vacuum. Groozles in the other nzetals and alloys forrned priniarily by sirface diffusion, the coefficients of which were calculated. Carbon was found to decrease the acti7:ation energy for surface diffusion on molybdenun. Sitrface diffusizities weve sinzilav for iWo-0.0ZC and Mo-33Re. The presence of about 1 -?nm pressure of silver or tin vapor did not affect the neckanis)n of grooz;e formation. In liquid titz or silz:er, pain bolindary gvooves formed by zolume diffusion in the liquid. BASED on theories of ullins," the mechanisms of grain-boundary grooving have been determined for low-melting metals such as copper in an inert atmospheres or in liquid lead.4 The purpose of this investigation was to study grain-boundary grooving in the refractory Group VI-A metals, chromium, molybdenum, and tungsten, and the bcc solid-solution alloys, r-35e, 0-33e,= and -25e,' at 0.6 to 0.9 of included to see whether Mullins' theories were applicable to them as well. EXPERIMENTAL WORK The materials chromium, molybdenum, tungsten, Cr-35Re, Mo-33Re, and W-25Re were in the form of 0.050-cm-thick sheet assaying 99.98 pct or better. The nominal carbon level was generally 30 ppm. The oxygen + nitrogen + hydrogen content was -50 ppm. Mo-33Re and W-25Re were prepared by powder-metallurgy methods and supplied by Chase Brass and Copper Co. The remaining materials were arc-cast. Chromium and Cr-35Re were prepared at Battelle by arc melting, extruding, swaging, and rolling. Mo-0.003C was supplied by Climax Molybdenum Co., and Mo-0.02C and tungsten by Universal Cyclops Corp. As a source of liquid metals, tin and silver granules assaying 99.98 pct were used. Spectrographic analyses indicated the presence of -100 ppm each of iron and silicon. Vacuum melting reduced the combined gas content to c5 ppm (2.60,, 0.9N2, 0.4H2 in tin and l.602, 0.7N2, and c0.04H2 in silver). Specimens were prepared for grain-boundary grooving. Coupons 0.5 by 1.5 cm with a small hole in one end, or substrates 1.5 by 1.5 cm, were cut from sheet. The specimens were annealed in containers of the same material to provide a vapor-solid equilibrium as well as to protect them from gaseous impurities. Outgassing was done at 2 x 10"5 mm for 15 to 30 min at 1150°C for chromium and Cr-35Re, 1750°C for molybdenum and Mo-33Re, and 2600°C for tungsten and W-25Re. Then recrystallization to a stable grain size of about 0.5 mm was accomplished by annealing at least 1 hr at 1600°C for chromium, 1800°C for Cr-35Re, 2350°C for molybdenum, and 2300°C for Mo-33Re in a rhenium-element resistance furnace under 1 atm of static argon or helium. The atmosphere was gettered by tantalum radiation shielding. Tungsten and

Jan 1, 1967

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By L. F. Stutzman, George Thodos

The friction factor plot presented by Cornell and Katz4 and developed for the flow of fluids through consolidated formations has been directly adapted for handling fluid flow problems involvitrg both linear and radial flow. In this adaptation the friction factor plot is used directly for the solution of problems and thereby eliminates the use of conventional equations which are specific to laminar (Darcy) or turbutent flow. This upproach overcomes the disadvantages inherent in the use of these conventional equations. It eliminates the necessity of checking the type of flow occurring in order to identify the specific equation which must be used. In radial flow problems, because of the increasing mass velocity of the fluids as they approach the wellbore. the type of flow may no longer remain laminar. Consequently, it is necessary to use more than one equation in a problem and to identify the range over which each equation should be applied. Finally, in practice it has been found that much of the flow of gases through consolidated media occurs in a range that is neither laminar or turbulent. For this transitional region, no convenient equations are available. The method and presented friction factor plot are appficahle to both liquids and gases. INTRODUCTION The flow of fluids through unconsolidated media in packed beds has been treated extensively by a number of investigatorsl,2,3,5,7,8 Most of these studies present friction factors as a function of modified Reynolds number similar to those developed for conventional fluid flow through pipes. These friction factor plots are presented for linear flow; however, Elenbaas and Katz have extended these concepts to apply to radial flow. All of these studies on unconsolidated materials require a knowledge of packing properties such as sphericity. porosity, and particle diameter. Sphericity and particle diameter cannot be defined at the present time for consolidated formations such as those commonly found in gas or oil reservoirs. As a result many investigators have not utilized friction factors and Reynolds number in the study of fluid flow through consolidated media. However, Cornell and Katz4 present a plot (Fig. 1) for the flow of fluids through consolidated porous media, in which the friction factor defined as: The turbulence coefficient, P, is related to the formation permeability, K, as presented in Fig. 2. Three different types of flow may exist in the flow ot

Jan 1, 1957

By R. J. Wygal, J. Naar

An equation for three-phase (water, oil, gas) imbibition oil permeability is developed, assuming the water to be the dominant wetting fluid. Oil isoperms are obtained for consolidated sandstones characterized by 1/pc2 = CS*. The evolution of an oil-gas system imbibing water from Swi to(Sw,imb )max is shown to proceed along a line of constant oil saturation with increasing oil permeability and decreasing gas saturation. When the gas satuation cannot be reduced further, the system evolves along a line of constant Sg with decreasing oil saturation and permeability. The initial gas saturation is shown to reduce markedly the effect of complete wetting by either oil or water on flow performance. INTRODUCTION Imbibition oil isoperms are required for performance prediction when a well is producing water, oil and gas. This situation occurs in multiphase displacements such as underground combustion, steam injection and the water flooding of highly depleted reservoirs. In a recent paper,1 a model was presented for the prediction of two-phase imbibition characteristics. This paper extends the imbibition model to the case of three phases by assuming that the water is the dominant wetting fluid. The following results were obtained from the model: (1) an analytical expression of oil isoperms; (2) oil isoperrns as functions of reduced water, oil and gas saturations, valid for all sandstones having a capillary pressure curve which can be approximated by 1/PC = CS*; and (3) evaluation of the three-phase flow performance as dictated by complete wetting by either oil or water. The agreement between predicted and observed oil recovery in the presence of a gas phase, reported in Ref. 1, is a partial support for the present development. However, experimental data are not available at this time to check fully the model predictions. Perhaps this paper will stimulate the collection of such data. The imbibition model of a porous medium has been described previously, and the reader is referred to the paper of Naar and Henderson1 for details. In brief, the model is formed by the random interconnection of straight capillaries, with a provision for the blocking of the non-wetting phase by the invading wetting fluid. The following expressions were derived from the model. 1. The amount of oil blocked by the invading water is

By P. S. Rudman

Laves phases, AB2, are considered as Izerrzisub-stitutional solutions m1hich are defined by a one-for-truo replacement scheme. Atomic-size tnisfit is considered in terms of deviations of the ratio 2V°b/V°A from unity, where v° = atomic volume. A simple elastic model has been used to calculated deviations from "Vegard&apos;s law of atomic vol-umes". Comparison has been made between calculated and observed atomic-volume deviations fov 222 Laves phases. Agreement is generally very good although there ave some few exceptions which appear to be excusable in terms of electronic changes that ore beyond the scope of the present model. We can consider the formation of a binary sub-stitutional solution A-B from an A solvent as one-for-one replacements of A atoms by B atoms. As the atomic-size ratio deviates from unity, the solution becomes thermodynamically less stable and hence more restricted because of atomic-misfit strain energy. In accordance with our previously presented conclusion1 that the atomic volume, v, is in general the most appropriate measure of atomic size, the ideal size ratio for a binary sub-stitutional solution is vg/vA = 1. The Laves phases have been described by Berry and Raynor2 in terms of various stacking sequences of hexagonal layers of B atoms for the three structures MgZn2(C14), MgCu2(C15), and MgNi2(C36). To form the Laves phase of ideal composition AB, we start with complete hexagonal layers of B atoms in the appropriate stacking sequence and we remove, according to an appropriate scheme for each structure, two out of every four B atoms and replace the two removed atoms by one A atom. We thus might expect to find that the ideal size ratio for the Laves phases is 2v/B/ VA= 1. From this point of view, then, we call Laves phases hemi-substitutional solutions since we employ one-for-two replacements. By analogy with substitutional solutions we can expect for Laves phases that as the ratio 2VB/Va deviates from unity the phase occurrence will be more restricted. Laves3 has plotted the distribution of Laves phases as a function of the radius ratio, ?A/rB, and found that, while the distribution extended from 1.05 < rA/B < 1.50, the

Jan 1, 1965

By J. D. Grace

Screening by centrifugal force is a unique subject, for all vibrating screens, with but one exception, depend on gravity alone to pass material through a sizing mesh or screen cloth. Centrifugal screening is one of the greatest advancements made in screening since the development of vibrating screens. It makes possible sizing in a range previously im-practical by mechanical methods. The centrifugal screen is specially designed for fine sizing from No. 4 separations to finer than No. 100 separations. Centrifugal force provides a positive control of factors that make fine particle separation practical and effective as opposed to gravity which is a fixed force acting only in a fixed direction, The centrifugal screen provides a control of the force of material against the screening surface, and also controls the distance of departure of the material from the surface and its rate of return. The centrifugal screen has a rotating drum that becomes a natural fan blowing air outward through the material being screened and carrying float dust and fines through the apertures with it. Screening by centrifugal force is an unique subject, for with the exception of only one vibrating screen presently on the market, all vibrating screens depend upon gravity to pass material through a sizing mesh or screen cloth. This one screen that sizes by centrifugal force and utilizes gravity only to convey material along the screen, is the Symons V-Screen. The requirements of the industrial minerals industry to meet ever-increasing stringent fine sizing specifications by a practical mechanical method accentuates the weakness of gravity, a fixed force acting in a fixed direction, as a prime force for fine sizing. It was apparent a force other than gravity was needed. This led to the development of a centrifugal screen to meet modern demands for practical fine sizing operations. Gyratory-type screens in use today were originally designed in a day when a 1/4-in. separation was normally considered fine sizing and 1/8-in. separations were extremely fine sizing. Although gyratory-type screens are sometimes used for separating below 1/8-in., they are not practical screens for this purpose. They were not designed to do this type of work. A growing demand for a practical means of making positive mechanical separations in a range of from 1/8 in. downward led to the development of the vibrating screen. These screens utilize higher speeds and lower amplitudes of vibration than

Jan 1, 1967

By Walter C. Lawson

THE first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1 1/3 miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1938

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By Walter C. Lawson

The first plans were made in 1930 for the mining by open-pit methods of the low-grade disseminated ore body now known as the Morenci open pit. It was not until 1937, however, that final plans were completed and the decision reached to go ahead with the actual development. Many advances were made in open-pit mining equipment during that period of seven years, therefore the ways and means of attack actually used were very different from those originally contemplated. Diesel-operated bulldozers, big trucks, full-revolving electric shovels and electric churn drills constitute the major equipment finally purchased for this modern stripping operation. Neither the bulldozers nor the big trucks were considered in the early operating plans, for at that time bulldozers had not been used in mining operations and the trucks as yet were undesigned. The full-revolving shovel and the churn drills were not new developments in open-pit equipment, but both had undergone remarkable manufacturing transition, emerging far more efficient and far more dependable than their predecessors. Even the ordinary drilling steel had been fundamentally changed. It was now threaded so that the dulled cutting bits could be detached and replaced, thus eliminating the costly transportation of long bars to the drill shop for resharpening. The decision to use trucks in the preliminary stripping operations was based on the desirability of this type of transportation to economically prepare the pit for rail haulage, coupled with the success that the contractors had had with them on other big excavation jobs. There are at present no plans for the use of trucks beyond the preliminary work, inasmuch as rail haulage will give lower costs after roadbeds and benches are once established. For many years to come, both ore and waste haulage will be over favorable grades. The average length of ore haul between the pit and an assembly yard will be about two miles. From there the crushers will be 1? miles with a connecting track grade of 0.4 per cent. The upper ore benches of the pit will be reached from the yard by a series of four switchbacks over a ruling grade of 4.0 per cent compensated for curvature. Tracks to the dumps will be on 0.2 per cent grades.

Jan 1, 1940

By K. E. Manchester, A. H. Clark

Hall measurements have been made on three groups of silicon samples, which were implanted with boron, aluininunz, and phosphorus ions. Boron and phosphorus implants show essentially bulk properties when annealed under previously determined conditions, i.e., 15 min at 80O°C for boron and 10 mirz at 600°C for phosphorus. Bulk properties were also observed in alu?rrilzum-implanted samples when ion concentrations were below 1015 cm-&apos;; however, strange low- terrzperalure behavior and a falloff in cavrier concenlralion was observed for sarnples with ion concenlration abozle loL5 ern-&apos;. This can be attributed to solid-solubility effects since the average bulk concentration f0.r the sample exhibiting bulk properties was below the reported solubility limit for aluminum, while the other samples were above the limit. A detailed study of the annealirzg process indicates that mobilities reach bulk c~alues in phosphorus implants at 250DC, in alutninurn ivnplanls a1 500°C, and in boron implants at 700°C. A simple rnodel has been proposed to fit the annealing data. THE technique of semiconductor doping by direct injection of energetic ions is being actively investigated at this Center. Previously published results from this laboratory have been concerned with the investigation of implanted profiles in silicon and the electrical properties of the resultant p-n structures.1&apos;2 Diode properties have been reported for junctions produced by implantation of boron ions and aluminum ions in n-type silicon and phosphorus ions in p-type silicon. Reverse current characteristics, as well as electron diffraction data, have indicated that the damage to the structure produced by the energetic ions during the stopping process can be minimized by a gentle anneal. The time-temperature conditions for this process have been determined by sheet resistivity studies.3 Electrical profiles of implanted phosphorus ions which have been determined by a differential sheet conductivity technique are based on the assumption that the carrier mobilities and activation energies for ionization are the same as in bulk silicon. These assumptions have been substantiated experimentally by measurement of Hall constants and resistivities of these implanted structures and the results are presented herein. After establishing the bulk property equivalence of the annealed layers, a more detailed examination of the annealing process was undertaken. The sheet resistivity technique initially used to determine anneal conditions has been broadened to include Hall constants and mobility behavior with anneal conditions. PROCEDURE The three groups of samples prepared for Hall measurements were implanted with mass-separated beams of boron, aluminum, and phosphorus ions. Ion concentrations are equivalent surface concentration and they have been determined from beam current measurements during implantation. Implant conditions for the samples are shown in Table I. In all cases, the samples had previously been angle-lapped on one edge and the junction delineated with an HF-copper sulfate solution. The surfaces of the implanted regions of the samples were exposed to the delineating solution and in the case of the "n"-type phosphorus-implanted areas it was later discovered that a finite amount of surface could be etched by this solution. This is discussed in the section on results. The implanted samples were ultrasonically cut into the conventional six-probe configuration shown in Fig. l.* In the annealing studies, for which the meas- urements were taken at room temperature, the sample holder was a Bakelite jig incorporating tungsten mechanical probes. The other measurements were taken using a conventional liquid-nitrogen cryostat, in which the temperature could be varied from 77" to about 400°K. For these measurements, 10-mil aluminum dots were evaporated onto the samples and alloyed with the silicon at 530°C for 15 min. The samples were then mounted in flat-packs, and gold wires were bonded to the aluminum dots. The electrical measurements were made with either a Leeds & Northrup K-5 Potentiometer, a Keithley 147 Nanovolt Null Detector, or a Keithley 601 Electrometer. No external bias was applied to the substrate. There is an inherent self-biasing arrangement at one or the other of the current contacts (depending upon the polarity), and this suffices to limit the current flow to the implanted layer. The magnetic field was generated by an A. D. Little electromagnet. Except for occasional checks of linearity of the Hall voltage with

Jan 1, 1969

By J. J. Gilman, T. A. Read

S URFACE effects in the cleavage of brittle crystals have been known for some oftime,1, 2 but our knowledge of surface effects in the plastic deformation of crystals is of relatively recent origin. In 1936, Roscoe9 eported his observations comparing oxidized and clean cadmium crystals. He found that cadmium crystals 1/2 mm in diam when covered by an oxide film less than 1200 atoms thick had critical shear stresses about twice those for clean crystals. This effect is anomalous in that it cannot be caused by the inherent shear strength of a normal oxide film. Either an interaction between the film and the crystal causes the large increase in strength, or the oxide film has an abnormal mechanical strength. Several authors since Roscoe have studied surface effects in crystal plasticity. A complete review of the literature will not be presented, but most of the results may be summarized as follows: 1—The critical shear stress for slip is increased markedly by very thin oxide films on zinc4 and cadmium crystals;" &apos; also, the entire stress-strain curve is raised by an oxide coating;3,4 both effects increase with decreasing specimen radius. 2—Surface active substances such as oleic acid destroy the hardening effect of oxide films.4, 6-8 The time required for the reduction of the hardening effect to begin increases with the viscosity of the solvent4~ 3—There has been dispute in recent years about the effects of surface active substances themselves on plastic deformation. Rehbinder, Lichtmann, and Maslenikov9 state that surface active substances reduce the strength of metal monocrystals markedly and increase the number of slip lines per unit length at a given strain. The effect varies with orientation for tin crystals being smallest for x, = 0, largest for x, = 45", and intermediate as x, + 90°.10 Several workers claim to have disproved the results of Rehbinder&apos;)"." but Rehbinder and Lichtmann9 have defended themselves and Masing with his collaborators" has confirmed some of Rehbinder&apos;s results. 4—Immersion of metal specimens in electrolytes such as sodium chloride reduces their strength12,13&apos; and subsequent cathodic polarization increases the strength reduction. For noble metals, the strength reduction occurs for both anodic and cathodic polarization," increasing with increasing polarizing voltage. 5—Electroplated copper coatings effect the creep rates of zinc monocrystals. Poly crystals are not affected." 6—Immersion in dilute acid destroys the hardening effect of an hydroxide film. When an acid solution is applied to a steadily creeping crystal, the creep rate jumps to a very high value and then drops gradually to a steady value which is higher than the initial steady rate.*&apos; " If the hydroxide film to be removed is very thin (about 100A thick), the creep rate does not change measurably, but a small rapid strain-increment is observed when dilute acid is applied." 7—Crystal plasticity depends on specimen dimensions. This was observed by Lichtmann and Ven-stroml" for monocrystalline tin and by Andrade and Kennedy" for polycrystalline lead. 8—Immerson of copper crystals in mercury has no effect on their stress-strain curves.&apos;" 9—Bombardment of creeping cadmium crystals with a particles which penetrate the surface to only 0.005 mm may increase their creep rates as much as five times.&apos;&apos;&apos; The experiments which will be described in this paper pertain to: (a) the effect of a crystal&apos;s shape on its plastic deformation, and (b) the effect of metallic surface films on plastic deformation. For the work pertaining to (a), crystals of zinc, tin, and lead were grown which had various shapes. These were tested in simple tension. Macroscopic rotations about the tension axis which are unpredicted by the classical theory of slip were observed, and serrated edges were observed in tin crystals. For the work pertaining to (b), the effects of evaporated and electrodeposited films of copper, nickel, gold, and zinc on the mechanical properties of zinc, tin, and lead crystals were determined. The films influenced both slip and twinning of the crystals in creep and tensile tests. Experimental Details Chemically pure zinc, tin, and lead were used in this investigation. The zinc was 99.999t pct pure;

Jan 1, 1953

By U. N. Bhrany, J. H. Brown

The specifications of particle size and the size analyses of fine particulate materials are commonly presented without reference to the method of analysis. A review of the various sizing methods showed that not only numerous sources of error but also different definitions of size are inherent in the different methods of analysis. To demonstrate the magnitude of the differences, the size distribution of finely crushed quartz was determined by several methods and a critical comparison of the data was made. The experimental results show that appreciably different sizes may be indicated for one material depending on the method of analysis used. However, because the shape of the size-distribution curves determined by almost all methods was constant, a simple method of correlating the data can be adopted. Conversion factors, by which size measurements obtained by the various methods can be expressed in terms of screen sizes, are presented as one method of correlating the results. The size analysis and size specification for lump rock and particulate materials are commonly determined with sieves. With this technique, a readily reproducible measure of size can be obtained merely by duplicating the sieve and the method of sizing. For coarse materials, such as lumps of rock, this technique is simple and effective; and the effects of properties of the material such as shape can be readily understood. When very small particles are measured, however, problems arise. Small sieves are difficult to construct and maintain, and size separations become sensitive to the analytical procedure. For these difficult sieve sizes and for still smaller particles, other sizing techniques employing, for example, sedimentation, light extinction, and microscopy are available. Because these various techniques employ different size-dependent responses to establish size, it is appropriate to examine them and the results they yield to determine their relationships and their limitations. The &apos;size&apos; of a lump of rock is not an absolute quantity, but rather a defined one. With sieves, for example, the size is defined by the screen aperture and no reference is made to the actual shape of the particle, yet only in the case of a regular body, such as a sphere, can the sieve size be related to the shape. With sieves only two dimensions of a particle can be suggested, for the sieve makes no allowance for the length of the particle passing through an aperture. Similarly, the size of a particle as measured by a microscopic technique need bear no relationship to the size as measured by sieves, although the two measurements may be related statistically. In fact, all size measurements are not only defined quantities, but the measurement actually used is an average that is controlled by the technique employed and, hopefully, reflects the property in question of the material of interest. Many papers have been presented that illustrate the accuracy of the various sizing methods, present the advantages of certain methods for certain applications, and describe the principles and technical backgrounds of the various methods. No attempt will be made in the present paper to review this work in detail. The purpose of the present paper is to examine the limitations of the various sizing methods, and to demonstrate experimentally the relationships between the sizes as determined by the various methods of analysis. It is hoped that by recognition of these limitations and relationships, errors in size specification and size interpretation will be avoided. REVIEW OF SIZING METHODS In specifying the size of a material, not only the data but also the method of measurement must be stated. For example, the size of the lump might be specified as its total volume, as its weight, as its maximum dimension, or as its minimum cross section; any one definition might be completely satisfactory for one problem, but not for another. In practice, size analyses follow four basic approaches and fortunately, the conditions that restrict each approach are known. These major methods include: 1) screen analysis, 2) direct measurement of particle dimensions, 3) determination of equivalent spherical size in response to fluid flow, and 4) specific surface determination. Each of these techniques has several variations and some new techniques are also available, but the limitations of the basic techniques are sufficient to permit at least a preliminary

Jan 1, 1962

By F. E. Jaumot, R. L. Smith

Self-diffusion in zinc at temperatures below 200°C has been studied using both single crystal and polycrystal samples. Anomalous results were obtained for single crystal samples, the data indicating that in some cases grain boundary diffusion predominated. These anomalous results are presumed to be due to low angle lineage boundaries in the single crystals. When volume diffusion occurred in either single or polycrystal samples, the values for the diffusion coefficient were as much as several orders of magnitude larger than would be expected from high temperature data. ONSIDERABLE work has been done on self-^-*diffusion at temperatures in the neighborhood of two thirds of the melting temperature (in OK) and higher, but very little has been done at lower temperatures. This is particularly true of self-diffusion in single crystals. This paper reports work on self-diffusion in zinc at temperatures below 200 °C where both polycrystalline and single crystal samples have been used. The measurements were made using both the sectioning and absorption techniques. The experiments on diffusion at low temperatures were initiated primarily for three reasons: to obtain data from single crystal diffusion covering a wide range of temperatures, to obtain values of the activation energy for grain boundary diffusion, and to obtain, if possible, a lower limit to the temperatures at which the absorption technique may be used. It is possible to determine whether volume or grain boundary diffusion predominates at low temperatures by analyzing the manner in which the concentration of the diffusing atoms varies with the depth of penetration. The analysis is possible only for the sectioning technique. For volume diffusion and for the boundary conditions of the present experiment, the curve of the logarithm of the concentration, C, vs the square of the penetration depth, x, is a straight line with the slope proportional to — 1/D. If grain boundary diffusion predominates, Fisher&apos; has shown that a curve of In C vs the first power of the penetration depth should be a straight line. This linear dependence of concentration on depth has been observed experimentally by several investigators. (See, for example, refs. 3 and 4.) Following Fisher&apos;s analysis, the grain boundary diffusion coefficient can be written as where 8 is the grain boundary width, D, is the volume diffusion coefficient at the temperature involved, t is the time of diffusion, C is the concentration of diffusing material, and x is the depth of penetration. A more general analysis employing the same model as Fisher&apos;s but with fewer assumptions has been given by Whipple.&apos; In contrast to Fisher&apos;s analysis the more general analysis of Whipple does not always yield a straight line relation between In C and x. Recently Turnbull and Hoffman have discussed both analyses and have applied the Fisher-Whipple model to a more refined dislocation model of the grain boundary. They have also discussed the possibility of a large effect of grain boundary direction on diffusion. In the case of the absorption technique, for which results are also given, one simply gets a value for the diffusion coefficient with no indication of the predominating mechanism. Experimental Techniques Single crystals of 99.99+ pct Zn were grown using a modified Bridgman method. Polycrystal samples were prepared in three grain sizes (small, about 4 mm2; medium, about 9 mm&apos;; and large, about 25 mmz) by quenching, air cooling, and furnace cooling. The grains of the polycrystalline samples tended to be columnar, with some preferred texture such that the c-axis was inclined at about 20" to 25" from the normal to the diffusion face, particularly in the medium and large grain size samples. The samples were cut from the rod, polished, and heavily etched, and faces cut accurately parallel using a jeweler&apos;s lathe. They were again etched to remove the lathe smear and annealed for 3 hr at 250" to 300°C. After annealing, they were etched, examined, and the orientation determined by Laue back reflection photographs. They were then electroplated with Zn. The plated surfaces were examined for uniformity; nonuniform coatings were removed by etching and the samples replated without additional preparation. For the diffusion anneals, the samples were placed in pairs, with active faces together, in evacuated Pyrex tubes. Constant temperature baths were used, and the variation in temperature did not exceed ±l°C, Diffusion runs were made at l00°,

Jan 1, 1957

By Craig R. Barreft, Oleg D. Sherby

The steady-state creep characteristics of pure polycrystalline copper were studied in the temperature range 400" to 950°C and in the stress range 400 to 7000 psi. Tests were conducted in dry deoxidized hydrogen and all specimens exhibited high ductility before fracture. Two activation energies for creep were established as a function of temperature. Above about T/T, = 0.65, the activation energy for creep was 48,000 cal per mole whereas between 0.5 and 0.65 T, it was 28,000 cal per mole. The observed temperature dependence of the activation energy for creep follows the same trend as exhibited by the self-diffusion coefficient of copper in copper single crystals and silver in silver single crystals. It is therefore believed that the rate-cmtrolling mechanism in creep of copper in the stress and temperature range studied is diffusion-dependent and is probably associated with a dislocation-climb process. The low activation-energy region is attributed to enhanced volume difFusion from the presence of dislocations which act as short-circuit paths for diffusion. THERE is extensive experimental evidence1,2 that the activation energy for creep, Q,, for pure poly-crystalline metals tested at temperatures above one half the absolute melting temperature (0.5 Tm) is a constant and equal to the activation energy for volume self-diffusion, Qsd This equality is generally interpreted as meaning that creep in this temperature range is controlled by a dislocation-climb process. The existence of high-temperature creep activation energies not equal to the respective self-diffusion values has been suggested both theoretically3"5 and experimentally.6-8 Two examples of apparent nonequality between Q, and Qsd have been reported for the cases of silver7 and copper,&apos; where activation energies for creep much lower than those for self-diffusion persist to rela- tively high temperatures (up to 0.6 T,). These observations suggest that dislocation climb may not be the only important process in the high-temperature deformation of these metals. That dislocation climb does indeed occur relatively slowly in these two metals due to their low stacking-fault energy has been suggested by many investigators.9-10 Although the creep behavior of copper has been studied extensively at low temperatures, the high-temperature activation energy for creep is not well-defined. The data of Feltham and Meakin8 indicated that Q, is temperature-dependent above one half the melting temperature, equaling a value of -30,000 cal per mole at temperatures up to 550°C and increasing to a value of -49,000 cal per mole at 700°C. No data has been reported above 700°C. The value of 49,000 cal per mole is very near the value of Qsd for copper reported by Kuper et al." as 47,100 cal per mole. In view of the lack of high-temperature creep data and the apparent temperature dependence of Q, for copper the present investigation was undertaken to determine the value of Q, over the temperature range of 400" to 950°C. It was hoped that such a study would clearly document the temperature dependence of Q, and yield significant information as to the nature of the rate-controlling creep mechanisms. MATERIALS AND PROCEDURES The material used in this investigation was high-purity OFHC copper. After rolling and recrystal-lization treatments spectrographic and chemical analyses showed only 0.0008 pct Ag, 0.0002 pctCa, 0.0002 pct H2, and 0.002 pct O2 as trace impurities indicating a purity of greater then 99.995 pct. Specimens were machined from cold-rolled sheet and the gage sections polished with 2/0 emery paper prior to annealing treatments. Annealing was done in both vacuum and dry deoxidized hydrogen atmospheres. No variation in creep strength was found as a result of the different annealing atmospheres. The final annealing temperature was either 700°, 800°, or 1000°C depending on the temperature range to be studied. These treatments resulted in average grain diameters of 0.03, 0.4, and 1.0 mm, respectively. The precise mechanical-thermal history of these

Jan 1, 1964