Search Documents

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By M. A. Dayananda

Based on the Kirkendall frame of reference, a method is proposed for the determination of atomic mobilities of all the diffusing species in a multicorn-ponent system with a single diffusion couple. The method is based on an atomic mobility model developed on the concept of negligible interactions among the intrinsic fluxes. It is shown in the model that mobilities can be obtained directly from the cumulative intrinsic fluxes past the Kirkendall interface. The proposed method replaces the need for a prior determination of interdiffusion coefficients far the calculation of mobilities. Relations between intrinsic diffusion coefficients and mobilities are derived and the mobility calculations are illustrated with diffusion data in Cu-Zn-Mn alloys at 850°C. ThE concept of "intrinsic flux" with respect to a fixed lattice was introduced "i Darken1 to explain toa Kirkendall effect2 demonstrated by the motion of inert markers during isothermal diffusion in single-phase binary solid solutions. Based on this concept, intrinsic diffusion studies have been made in various binary metallic systems3,4 employing such a lattice frame of reference, commonly referred to as the Kirkendall interface. Similar approaches, both theoretical and experimental, have been presented5"10 to study intrinsic diffusion in multicomponent systems. Based on the direct integration of Fick's law extended to multicomponent diffusion, Philibert and Guy8 proposed a method for the determination of intrinsic diffusion coefficients. For an n-component system, this procedure requires an experimental study with (n — 1) diffusion couples, all having their Kirkendall interfaces at the same compositio;, where n(n — 1) intrinsic diffusion coefficients are defined. This technique has been employed for ternary diffusion studies by Dayananda and Grace" and Guy and Leroy.11 A different approach is recommended by Ziebold and Cooper,12 who have derived relations between interdiffusion coefficients and atomic mobilities employing fluxes referred to the local center of volume. Their analysis is based on the simplifying assumption of negligible interactions among intrinsic fluxes. This assumption has been considered satisfactory for dilute solutions.5"7 The use of this analysis for the calculation of mobilities requires an initial determination of interdiffusion coefficients with a set of diffusion couples having intersecting diffusion paths. It is the purpose of this paper to propose a method that would permit a direct determination of mobilities of all components of a multicomponent system from a single diffusion couple. This method is based on a mo- bility model developed with diffusion fluxes referred directly to the Kirkendall interface, generally identified by inert markers. gen erall, like that of Ziebold and Cooper,12 employs the simplifying assumption that the flux of each component relative to a fixed lattice is caused only by the driving force of its own chemical potential gradient. THE KIRKENDALL INTERFACE Inert markers are employed in diffusion couples to locate experimentally the position of the Kirkendall interface. They are initially placed at the weld interface for "sandwich" couples, or at the original vapor-solid interface for vapor-solid couples. Studies of marker motion in binary systems3'4 with both types of couples indicate that markers remain in a plane of constant composition and move with this plane para-bolically with time. Parabolic marker movements were also observed in ternary Cu-Zn-Mn couples by Dayananda and Grace.10 It is reasonable to expect a similar marker behavior even for diffusion couples with a higher number of components.

Jan 1, 1969

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant's elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

INTRODUCTION Besides the European export credit agencies covered in Ted Rides' paper in this Chapter, other agencies are also active (see Appendix) but the most notable for mining projects are The Export-Import Bank of the United States ("US Exim") and the Export Development Corporation ("EDC") of Canada. Mexico's Fomex is basically a short-term trade-finance fund administered by the Central Bank. US Exim This independent agency can provide loans, guarantees, and insurance. Like all export-credit agencies, its mandate is to support the export of goods and services from the US as a means of competing against other countries' products. If a piece of mining equipment can only he made in the US, the US Exim may very well not provide any financial assistance. (It is important not to place the order for any item for which export credit is sought because, once ordered, the situation is no longer competitive in US Exim's eyes.) Direct Credits and financial guarantees ("buyer credits") are commonly in amounts greater than 85 million and for terms longer than six years. An example here is the $48.5 million provided to PT International Nickel Indonesia (see Robert de Gavre's paper in Chapter 12). US Exim usually requires a 15% downpayment and, therefore, finances up to 857 of the goods; less if the US content is lower. The dollar funding can he US prime, London Interbank Offered Rate (LIBOR), or other sources. Exim can fund in either or both of the following ways: 1. Under a US bank Letter of Credit ("L/C") 2. Reimbursement to the buyer/borrower via a US bank account. US Exim will, without charge, issue a preliminary commitment. It will, however, need to approve the various credit agreements and prefers to tie other parallel financings into one loan agreement. US Exim's total commitments are large, up to $5R billion in aggregate under various programs. US Exim has been the world's leader in medium-to long-term minerals project financings/ co-financings but suffers from (i) aggressive foreign export-credit competition whereby other nations mix in soft-loans or aid programs ("mixed credits") to increase the percentage financed and lower the interest margin and (ii) an imbalance in its own cost of funds. A common US Exim package would be as follows: 15% Banks under US Exim guarantee, floating rate over prime or LIBOR. 35% US Exim funding, fixed rate 35% Pefco funding, fixed rate 857 Drawn down pro-rata under US bank L/C 15% Cash down payment (may have been financed within a project/corporate credit) 100% Repayment usually begins six months after planned start-up in equal semi-annual instalments, with the banks usually paid out first, Pefco next, and US Exim last. Medium-term credits ("supplier credits") are issued for US equipment exports for terms up to five years, again for 85% of the equipment costs although the exporter is expected to bear at least 10% out of that 857 for its own risk. The buyer is required to be a first-class credit such as some governments or highly credit-worthy companies. Otherwise a bank L/C would be required. (This may be wrapped into an overall project-finance package for a minerals development. The project-finance banks provide an L/C to US Exim instead of funding that portion themselves.) US Exim guarantees 100% of the political risk and either 85% or 95% of the commercial risk for

Jan 1, 1985

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By A. B. Cummins

THE past year has been of unusual interest for industrial minerals. It is increasingly evident that requirements for these raw materials move with general economic trends. Thus, with a peak year in the construction, chemical and petroleum industries, the nonmetallic mineral industries have been brought into the complex maze of an economy in which military spending is in the billions and in which the national income and wholesale commodity prices reached new levels. Many industrial minerals are of first rank essentiality in the defense effort and its supporting industries, and since some of these are of limited supply and others dependent on imports, the problems of procurement, distribution and conservation of available supplies make a complicated pattern. Despite some drawbacks and weak spots, the industrial mineral industries have, in general, met the national situation with great credit and many new production records have been set. The general accomplishment in 1951 should be one of satisfaction with confidence for the future. Difficulties, unsolved problems and uncertainties should not obscure the general trend which many consider optimistic. Prices in the main have been upward, in line with the inflation spiral, but nonmetallics appear with some exceptions to be behind the general increases. Labor difficulties have not been serious throughout the year. Retarding influences in expansions and planning have been the uncertainty of the Korean and international situations and a lack of confidence by many in the government economic program and its ultimate impact on the economic structure. It must also be kept in mind that stockpiling, unless all-out war develops, reaches a level and then ceases to be a major sustaining factor in the mineral markets. In accordance with the Defense Production Act of 1950 various control agencies have been set up to establish the desired rate of stockpile acquisitions. The objectives are subject to change depending on availabilities and needs-military, industrial, and civilian. In some minerals there has been disagreement on actual stockpile requirements, and there is some feeling that the needs of defense might be better met if more funds went into the development of new sources of supply of scarce raw materials and more materials were released to industry at this time. Nonmetallic minerals on the strategic and critical list of the Munitions Board as of July 1951 were: Group I; asbestos, some types; bauxite, refractory grade; beryl; celestite; chromite, chemical and refractory grades; columbite; corundum; diamonds, industrial; fluorspar, acid grade; graphite, some types; kyanite; manganese ore, battery and chemical grades; mica, some types; quartz crystals; rare earths; sapphire and ruby; talc, steatite, block; and Group II; bauxite, abrasive; cryolite, natural; diamond dies; graphite, crystalline fines; iodine; mica, muscovite block, stained and lower; rutile; selenium; talc, steatite, ground; zirconium ore, zircon. Details on the current status of stockpiling inventories are not available. The Defense Minerals Exploration Administration has, since April, executed 39 contracts for the exploration of nonmetallic minerals, including twenty for mica, seven for beryl-mica, six for asbestos, three for sulphur and one each for monazite, steatite talc and fluorspar. Total value of these contracts came to $892,059, of which the Government&apos;s participation amounts to $689,247. There were on hand at year&apos;s end another 97 applications for exploration aid on nonmetallic minerals in twenty different

Jan 1, 1952

By Harold L. Overton, Leonard B. Lipson

The first paper in this series1 outlined practical methods for applying the theory of steady-state flow of an ideal Bingham plastic liquid through a circular pipe and axially through a stationary concentric annulus to the enginekring analysis of friction loss problems. In the present paper the properties of another useful rheological model, the pseudoplastic generalized Newtonian liquid, are considered. The terminology applied to the rheological models is derived from the following classification of rheological models. The term "generalized Newtonian" is a class designation applied to models which do not have yield points but which exhibit a dependence on shear rate. The term "pseudoplastic" applies to a sub-group of models within this class which exhibit a decrease in "viscosity" with increasing shear rate. The term "power model" refers to a mathematical model proposed for describing the behavior of the pseudoplastic liquid. This model is of interest since certain of the salt saturated, oil emulsion, and "low solids" drilling fluids, inverted emulsion- and oil-base drilling fluids, aqueous gels, gelled crudes and blocking agents employed in hydraulic fracturing operations are of this type. The present treatment considers the equations describing steady-state Poiseuille flow through a circular pipe and a stationary concentric annul us, and Couette flow between concentric rotating cylinders for a particular pseudoplastic model. As in the previous paper&apos; it is demonstrated how these equations can be applied to engineering calculations of friction losses. Graphical procedures for recovering the various flow curves and cxample calculations are included. A method for simplifying turbulent-flow correlations is also proposed. PROPERTIES OF PSEUDOPLASTIC GENERALIZED NEWTONIAN LIQUID In contrast to the Bingham plastic the generalized Newtonian liquid is yield point-free. However, in the flow region the relation between stress and rate of shear is not linear as it is with ordinary Newtonian fluids. If the stress increases with shear rate at a less than linear rate the system is called pseudoplastic. While there is no yield point in this system, the Bingham advocates&apos; coined the term pseudoplastic to distinguish this kind of behavior from Bingham plastic behavior. For the pseudoplastic a plot of flow rate vs friction loss or rpm vs torque, from pipe flow or rotational viscometer measurements, respectively, generally has three qualities: (1) it can be clearly extrapolated toward the origin; (2) there is very little slope at the origin. This accounts for the high apparent viscosities at low mixing and pumping rates; and (3) the flow curve possesses a continuous curvature which gradually diminishes as the shear increases. Rheological measurements on a pseudoplastic liquid can be easily misinterpreted as indicating Bingham plastic behavior. A typical case in point is illustrated in Fig. 1. These data were obtained from measurements on an oil-emulsion mud using a commercially available rotational-type viscometer (Model 35 Fann V-G meter). Applying the "two-point"* method3 gives a plastic viscosity of 17 cp and a yield point of 24 lb/100 ft2; at the same time weighting material settles very easily in this system. This illustrates that it is not possible to distinguish between the pseudoplastic and the Bingham plastic from only two data points. It is possible to determine qualitatively which model is more appropriate by a combination of dynamic and static measurements. Experience indicates that the simplest criterion for the Bingham plastic liquid is that the calculated dynamic yield point should be of the same magnitude as the measured gel strengths. For the oil-emulsion drilling fluid illustrated in Fig. 1, a value of 4 lb/100 ft2 was obtained for gel strengths measured

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter&apos;s tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.&apos; The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"&apos;, an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By Langtry E. Lynd

The predominant tonnage use of titanium is as a white pigment, in the form of rutile or anatase, which are allotropic modifications of titanium dioxide. Because of its whiteness, high refractive index and resulting light scattering ability, titanium dioxide is unequaled as a white pigment for paints, paper, rubber, and a wide variety of other materials. Consumption of titanium dioxide pigments for these uses has been rising steadily for many years, United States consumption in 1956 amounting to about 486,000 tons, worth $250,000,000. Production was off a little in 1957 and 1958. An outstanding development in the titanium field in recent years is the expansion of titanium metal production. Virtually nonexistent before 1948, United States production of pure titanium metal sponge reached a high in 1957 of about 17,200 tons, worth about $77,000,000. United States titanium sponge metal production in 1958 was cut back to about 4,600 tons because of reductions in military requirements. Another major use of titanium, in the form of the mineral, rutile, is for welding rod coatings. United States consumption of rutile for this purpose in 1958 amounted to about 11,000 tons, worth $1,100,000. Titanium-Bearing Minerals Although several minerals contain titanium as a major constituent, only a few of these occur in sufficient quantities and concentrations to be of commercial importance. These are ilmenite (FeTiO3), rutile (TiO2), and alteration products of ilmenite which have been referred to as weathered ilmenite, leucoxene, or arizonite. The other polymorphs of titanium dioxide, brookite and anatase, occur in a few deposits, of which only one has been of even minor importance. Considerable concentrations of titanite or sphene (CaTiSiO5) and perovskite (CaTiO3) are known, but do not compete with ilmenite and rutile deposits in grade or size. Rutile is very widely distributed as an accessory mineral in most rocks, but large deposits of commercial importance are rare. A few rock deposits have been worked for rutile but only one, in Virginia, is in operation (1959). Development of one in Mexico was discontinued recently. At present, the main sources of rutile are the beach and dune sands of Australia and Florida. A major use of rutile is for the manufacture of titanium tetrachloride, which is the intermediate compound universally used in titanium metal manufacture. Another main use of rutile is for welding rod coatings. Although the whiteness and brightness of titanium dioxide pigment is due to the high refractive index of rutile or anatase, natural rutile is too impure to be used directly as a white pigment, is too expensive to use for manufacturing pure oxide pigment, and is too scarce to provide the required tonnages. Instead, the cheaper, more abundant, mixed oxide of iron and titanium, ilmenite, which is readily decomposed by sulfuric acid, is used for manufacture of rutile and anatase pigments. Ilmenite is mined from both rock and sand deposits. Rock deposits contain ilmenite in massive or heavily disseminated form along with magnetite or hematite and are almost invariably associated with anorthositic and gabbroic rocks. Ilmenite also occurs as an accessory mineral in a great many igneous and metamorphic rock types. Concentrations of

Jan 1, 1960

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh, Pa. The Mellon Institute of Industrial Research has carried on for years research and investigations for all type and manner of indus¬try. One of the provisions of the foundation of the Institute is the

Jan 1, 1933

By C. K. Leith

The question as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to the individual ore deposits, and seems to call for some sort of quantitative answer.

Jan 1, 1915

By D. Kramer

HASEN1 has published a phase diagram for the zirconium-nickel system. This phase diagram has been redetermined by Hayes, Roberson, and paasche2 in the range 0 to 50 at. pct Ni. Recently, Smith and Guard3 have published a tentative diagram for the

Jan 1, 1960

By R. D. Mollison

"For his contributions to mining which are highlighted by perseverance; successful exploration, particularly the Kidd Creek deposit; technological advancement and sound management policies; and for his lecture, "Exploration-The Diversificiation and Development of a Mining Company." Recipient of the 1983 D.C. Jackling Award

Jan 1, 1984

By L. E. Schiffman

This paper describes the operation of two kerosine flotation plants in Alabama for cleaning -10 mesh bituminous coal. One plant treats washer sludge, the other raw coal. Data on capacity efficiency and capital and operating costs is given. Methods for increasing cell capacity are discussed.

Jan 10, 1950

TO metallurgists generally, Arthur S. Dwight is no stranger even to those who do not know him personally. He is one of those contributors to technical progress whose names will go down to posterity because of their being attached to a successful machine or process, such as Dorr, Hardinge, or Marcy, or Wedge, MacDougall, or Herreshoff. The roasting and sintering method and equipment developed by Colonel Dwight and his associate, the late Richard L. Lloyd, may be found in lead smelters throughout the world, and also in many metallurgical works dealing with other ores, including those of iron. It is ordinarily used to desulphurize and agglomerate fine ores for subsequent smelting. Colonel Dwight&apos;s citation as James Douglas Medalist reads: "For his contributions to the art of smelting nonferrous ores; and particularly for his pioneer work in developing equipment and technique for sintering such ores and metallurgical products." The medal was awarded at the last Annual Meeting of the A.I.M.E. but unfortunately the medalist was unable to leave Florida at the time to receive it in person.

Jan 1, 1942

By William L. Langdon

PRELIMINARY COMMENTS Recent years have been difficult for the mining industry, as reported in the most recently published Minerals Yearbook (Volume III), the estimated value of world crude mineral production has been generally declining since an historical peak in 1979 (16).* The costs of mineral extraction have, however, been rising rapidly. Individual project costs are, in general, exceeding the growth rate of mining companies, while operating and technical risks continue to increase (16). Risks resulting from currency flotation and political actions in the host country are also on the increase. Labor difficulties (such as those experienced by Phelps Dodge) and the Reagan Administration&apos;s recent rejection of a proposal by the International Trade Commission for higher tariffs and/or quotas on copper imports have also contributed to the mining industry&apos;s difficulties. The net result of these factors has been financial difficulties for mining companies with respect to paying for their current financial obligations as well as trouble finding new financing. It may be that one of the main factors in determining the future of the mining industry will be centered upon capital structure, i.e. how its assets are financed. Historical Perspective on Capital Structure In The Mining Industry As discussed by Isreal Borenstein in (4) and Thomas Navin in (7), mining firms typically have used a financial model based upon high financial leverage, i.e. large amounts of debt relative to equity. This has been especially true for American firms developing orebodies discovered overseas. Problems sometimes occurred for those who were forced to commit themselves to completion guarantees in order to obtain bank loans. Mines under these circumstances must be brought into operation regardless of market conditions. Politicians in overseas countries also may use the high profits required by these high risk ventures to argue for nationalization of mines. Coupled with the frequent use of high leverage, mining companies traditionally have paid out a higher percentage of earnings in the form of dividends than manufacturing firms. This is significant, in that such funds paid out in dividends are not available for other uses. Hence, a greater reliance upon debt and/or additional stock issues than would ordinarily be the case for manufacturing firms. Thomas Navin has stated in (7), that the theory behind the high dividend payout was that, "most mining investors thought of themselves as investing in a wasting asset, one that would gradually deplete over time until it ultimately became valueless." Investors, therefore, required a receipt, in the form of dividends, of a percentage of current earnings and a return on original capital. This view of reality, apparently, has not changed in some quarters, even though modern mine management ordinarily replaces depleted mines with new ones. It may be that this practice of high dividend payout coupled with relatively high financial leverage should be reexamined. Current capital structure theory could prove interesting and useful for those concerned with current conditions. Capital structure patterns and related practices in this industry are not, in many cases, congruent with those thought by some to be theoretically optimal. Prelude to Capital Structure Discussion With a few notable exceptions (such as the Guggenheims and Anaconda&apos;s chief operating,. officer in 1971) mining companies&apos; chief executives and boards of directors have not been persons with financial backgrounds. This, one could conjecture, might have accounted for the relatively nonsophisticated nature of capital structures of mining companies. In order to appreciate the possibilities with respect to alternative influence on a firm&apos;s performance, one must be acquainted with the basics of financial theory. This paper is an attempt to familiarize the reader with (1) capital structure in general, (2) the usual components of this structure, (3) the general theory behind the use of financial leverage, and

Jan 1, 1985

By R. D. Vaughn

The analysis of laminar flow of power-law non-Newtonian fluids in narrow, eccentric annuli is employed in this paper to discuss the problems of lubricant flow in journa! bearings and of errors introduced by eccentricity in experimental studies with concentric annuli on extruders and wellbore annuli. The velocity profile and pressure loss-flow rate equations are developed for the laminar flow region. In addition, the expected error in flow rate and pressure-loss measurements for concentric annuli as a result of eccentricity is determined. For example, a 10 per cent displacement of the core of an almost concentric annul us would cause a 1.8 per cent decrease in the observed pressure loss for a fluid with a power-law exponent n of 0.25. The corresponding increase in the observed volumetric flow rate would be 7. 5 per cent. INTRODUCTION Non-Newtonianism and eccentricity occur simultaneously in two engineering problems: (1) flow of lubricants in journal-bearings and pressure-reducing bushings, and (2) flow of non-Newtonian fluids in plastic extruders and wellbore annuli. The lubricants used for moving parts are often non-Newtonian in character — often they are plastic in behavior. A solution to the problem of flow of non-Newtonian fluids in narrow eccentric annuli is particularly pertinent to this problem. In all experimental studies of laminar flow of fluids in concentric annuli, such as in extruders and well casings, the error due to eccentricity must be estimated or studied. A number of publicationsl-4,6,7 have dealt with this problem for Newtonian fluids; however, I am not aware of work for non-Newtonian fluids. This work is directed to the non-Newtonian problem. Before the solution to the problem is given, the pertinent conclusions from the work on Newtonian fluids will be reviewed. Heyda 1 and Redberger and Charles 2 have published general solutions to the problem of the laminar flow of Newtonian fluids in eccentric annuli, apparently without knowing of the earlier work of Ca ld well 3 and Bairstow and Berry,4 which is reported by Dryden, et al. 5 Although several mathematical routes are encompassed by the work of these authors, the results appear to be equivalent. Redberger and Charles2 show that the error caused by eccentricity in concentric annuli is negligible for small diameter ratios (k < 0.5); however, for large diameter ratios (k + l), the error in the predicted flow rate can be as great as 100 per cent or more. Partial solutions to the problem are available from the work of Dryden,5 Tao and Donovan6 and Piercy, et a1.7 Tao and Donovan examined the case of flow in narrow, eccentric annuli (k + 1) with and without rotation of the annular core. These authors also reviewed previous work on this subject and verified their approach with experimental data. Dryden gives the solution for the limiting case of complete eccentricity or tangency. Piercy, et a l. published an early solution to the problem of narrow eccentric annular flow. The conclusions of Redberger and Charles2 and the experimental proof of Tao and Donovan6 both suggest that the region of large diameter ratios (k + 1) is of main interest and that the parallel planes approximation to the solution in this region is satisfactory. This method will now be extended to the laminar flow of non-Newtonian fluids in narrow eccentric annuli. THEORETICAL SOLUTION The geometrical aspects of the problem are illustrated in Fig. 1. To represent the non-Newtonian fluid the power-law model was selected. This model has many disadvantages which have been pointed out; nevertheless, its simplicity, its frequent and wide applicability justify its use in this work. Fredrickson and Bird8 and Savins9 have used it as a basis for a theoretical study of laminar flow of non-Newtonian fluids in concentric annuli.

Jan 1, 1966

By J. D. Doherty

That America&apos;s great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Incr ase imports. 3. Develop new sources such as synthetic liquid fuels. All three courses may well be needed, as it is doubtful that any one of the three alternatives alone can satisfactorily solve the problem indicated by the prevailing trend in demand for oil. Curtailment of oil consumption is not a constructive policy, except where oil is being wasted or coal can be readily substituted as in stationary steam plants. Reduced oil supplies for most uses will curb our economic advancement and, in addition to inconveniencing consumers, will have a pronounced adverse effect on American industry. The oil-burner-manufacturing industry already has been dealt a hard blow. Shipments in the first 5 months of 1948 decreased 70 pct from those in the same period in 1947.1 The effect of a similar cut in the automobile industry can be imagined. A severe prolonged shortage of gasoline could seriously disturb our present economic well-being. It might be pointed out also that even the prospect of a shortage or lack of assurance for the future can discourage buyers of equipment, as occurred in the case of oil burners. An increase in our imports of oil seems to be a necessary expedient for the immediate future. Its advantages are that it will require a minimum of manpower and steel in a time of critical shortages and will conserve domestic reserves. Any major dependence upon foreign sources for our oil supplies should be avoided, however. Other nations are increasing their oil consumption more rapidly percentagewise than the United States and eventually will compete with us for the not unlimited world supplies. In peacetime, foreign countries might restrict ship- ments of oil to this country or impose exhorbitant prices. In the event of war, there is serious danger that such sources would be cut off, and American-developed oil fields overseas might even be used against us. Although synthetic fuels cannot relieve any oil shortage that might develop within the next year or two, an immediate start toward a substantial synthetics industry to supplement petroleum not only could help relieve shortages several years hence but also would help establish the much needed "know-how" for large-scale production. By assuring ample future supplies, such a start would permit sound planning by industries dependent upon oil and maintain or restore the confidence of prospective customers for oil-con-suming equipment. If it is agreed that domestic production of crude oil cannot be expected to meet future domestic demands, that oil rationing in general is undesirable. and that too great dependence on foreign oil should be avoided—and the weight of the evidence supports such conclusions—it is inescapable that commercial synthetic fuel production should be developed to supplement domestic petroleum supplies, which, of course, will furnish the bulk of our requirements for yean to come. Sources of Synthetic Oil The three principal sources of synthetic oil are natural gas, oil shale, and coal. A commercial plant using natural gas is under construction, and expansion of this industry is expected.

Jan 1, 1950