Search Documents

By J. C. Wilhoit, E. M. Galle

A three-dimensional photoelastic study was made to determine the stress state around the wall and bottom of a wellbore due to fluid pressure within the wellbore and unequal principal geostatic stresses. Models simulating the wellbore were made from a phthalic anhydride-cured epoxy resin. The frozen stress technique of three-dimensional photoelastic-ity was used to determine the stresses within the model. Two separate problems were solved: (1) hydrostatic pressure on all sides of the model with the exception of the inside of the hole, and (2) uniaxial compression perpendicular to the center line of the hole. The results are presented in the form of contour curves for each stress component. The curves cover a region which extends several hole radii from the bottom and wall of the hole. By proper use of these results, the state of stress may be calculated for any point on the wall or bottom of the hole, as well as for any point within the material that surrounds the hole. A systematic method is given for calculating these stress components for any combination of fluid pressure within the wellbore and system of unequal principal geostatic stresses, provided one of the principal geostatic stresses is parallel with the wellbore. The results show that stresses around the wall and bottom of a wellbore, induced by an uneyual system of principal geostatic stresses, are appreciably different from those induced by geostatic stresses that are hydrostatic. For uneyual principal geostatic stresses, the experimentally determined stresses on the wall of the hole several radii from the bottom are in good agreement with the stresses calculated by elastic theory. INTRODUCTION Interest in the problem of determining the stresses around and near the bottom of a wellbore, due to geostatic loading and fluid pressure within the wellbore, originated in the petroleum industry. The stresses on the wall of the wellbore are of interest due to their relation to lost circulation during drilling, the fracturing of formations during squeeze cementing and hydraulic fracturing of producing formations. The stresses on the bottom of the hole are of interest to the drilling segment of the industry because to produce a hole in the earth it is necessary to remove material from the bottom of the hole. This removal of material is produced by structural failure of the rock, whatever the criterion for failure may be. Cunningham and Eeninkl have shown that for certain conditions the effect on drilling rate of the bottom-hole stresses caused by a hydrostatic overburden pressure is small compared to other effects. This question, however, needs further experimental and analytical investigation. Much information concerning the stresses on the walls of wellbores has been published considering both equal and unequal principal geostatic stresses. The problem of determining the stresses around the bottom of the wellbore is considerably more complicated. However, previous investigators have obtained numerical and experimental solutions to the problem for equal principal geostatic stresses. whitworth2 and woods3 have obtained numerical solutions. word415 obtained a three-dimensional photoelastic solution, Durelli and Deily 6 obtained surface stresses only by photoelastic means, and Cheatham and Wilhoit7 determined the stresses around the bottom of a short cylindrical cavity. While Miles and McGuire, Harrison and Kieschnick and Hubbert and Willis 10 obtained the stresses on the wall of a wellbore for unequal principal geostatic stresses, they did not concern themselves with the stresses near the bottom of the hole. The estimates made by Hubbert and Willis of the differences between the principal geostatic stresses indicate that, to obtain a satisfactory solution for the stresses around the bottom of a wellbore, unequal principal geostatic stresses should be considered. This work is directed toward obtaining such a solution. The materials in the earth's crust are nonhomo-geneous, permeable and anisotropic. Previous

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By R. E. Collins

The existence of fluid migration across fixed boundaries in oil and gas reservoirs has been known for many years. Several techniques have been developed in the past for estimating The rate of migration across fixed boundaries as an aid in planninng field development and in the valuation of oilfied properties. The principal de/errc7nt to the use of these techniques lies in the rather extensive reservoir and field data required for ca1cula1ion.s of fluid migration. For this reason, a new, simplified procedure has been developed which makes possible the calculation of fluid migration with a minimum of field and resrvoir data. This new technique is based on certain. solutions of the differential equations describing flour in the reservoir which assume, for the portion of the reservoir of interest, that the formation can be approximated by a homogeneous rock of uniforrn thickness, that only a Single mobile fluid phase exists, and {hut fluid production at the well is solely a result of expun.rioti of rile resersoir fluds. The results of the, present work are compiled in a set of curves. These curves can he used to calculate both rule and cummulative fluid migration when the abovc assumptions ore ju.r/ifiril. The only data required for such calcu1ations are the production hisrories of all wells in the field, the permeability and porosity of the reservoir., the, compressibility and viscosity of the fluid. and the shape of the reservoir, INTRODUCTION The migration of fluids across fixed boundaries in oil and gas reservoirs has long been recognized as an engineering and economic problem, but no methods for estimating the extent of migration during the development stage of a reservoir have been published. The investigation reported here has been directed toward providing a simple technique for estimating the extent of such migration and has therefore been restricted to the simple case of a homogeneous reservoir of uniform thickncss containing compressible liquids. It is assumed that only a single mobile fluid phase exists and that fluid production at the wells is solely by expansion of the reservoir fluids. Obviously, few, if any. reservoirs conform to these assumptions during their entire productive life. On the other hand, most reservoirs approximate fluid expansion reservoirs during their initial stages of primary production. Consequently, the present work should be applicable during the field development of most reservoirs, regardless of whether or not they ultimately are gas cap, dissolved-gas, or water-drive reservoirs. The mathematical analysis of this problem has been outlined in the Appendix, while the results of the investigation are presented in the following discussion. DISCUSSION OF CALCULATION PROCEDURE SLNGLE Well, Ini-iimite Reservoir The procedure for calculating fluid migrations is based on solutions of the partial differentia1 equations describing the flow of a homogeneous compressible liquid in a homogeneous reservoir of uniform thickness. This differential equation has the form of the well-known diffusion equation. The equation, as applicable to our problem, is where p is fluid density, is porosity, EL is viscosity, c is compressibility,* and k is permeability; .r, y and t are the space coordinates and time. Derivation of this equation is given in the Appendix. The analytical solution of this equation for a single well of negligible radius producing at a constant rate. q, from a reservoir of infinite areal extent for a time, 1. can he readily obtained. From this solution the rate of flow and also the cumulative flow across a straight line segment of length, 1, at a perpendicular distance. 6. from the well can be computed. One end of the line must be on the perpendicular joining the well to the

By R. E. Cook

This paper presents results of a study to determine to what extent errors in estimated free gas saturation affect the results of static pressure calculations from build-up curves in two-phase systems. Use is made of the method of pressure build-up curve analysis developed by Miller, Dyes and Hutchinson1 , with modifications for two-phase flow advanced by Perrine2. Cornhined fluid compressibility of gas-oil mixtures is included, with special attention given to the discontinuity that occurs in fluid compressibility at the saturation pressure and its effect on static pressure calculations from build-up curves. The sensitivity of static pressure calculations to errors in gas saturation is considered over wide ranges of formation and fluid properties and reservoir pressure conditions. It is concluded from this study that for analyses of two-phase pressure build-up curves (I) the use of under-saturated crude compressibility data, even when producing GOR's are at or near solution values, will result in very significant negative errors in calculated static pressrrre, and (2) except for large values of buildup curve .slope and/or very low crude gravities, rather large errors in calculated gas saturation can he tolerated without .significant effect on calculated static pressures. The conc1usions arc qualified as referring only to the effects of gas saturation and excludc possible errors in the nuumerous other factors that enter into the ancllysis of pressure build-up curves. INTRODUCTION As part of the analysis of basic data for several major Eocene reservoirs in the Bolivar Coastal field (Western Venezuela), it was necessary to analyze a large number of pressure build-up curves for oil permeability and static reservoir pressure. From performance data it became apparent that gravity segregation is very active in these reservoirs. As a result of this performance it was recognized that the free gas saturation within the oil leg of the reservoirs would be small but would be subject to certain errors in calculation due to the inaccuracy of relative permeability data in the low gas saturation region. Since all of the various methods of build-up curve analysis were originally derived for sin- gle-phase, constant compressibility systems, and since the presence of a small but rather indeterminate gas saturation would greatly affect the reservoir fluid compressibility, a study was undertaken to investigate the effect of gas saturation on the results of two-phase pressure build-up analyses. TWO-PHASE BUILD-UP CURVE ANALYSIS The method of analysis used in this investigation is basically that originally developed by Miller, Dyes and Hutchinson1, with modifications for two-phase flow advanced by Perrine2. Miller, et al, showed that the original equation for single-phase permeability away from the well bore, held for two-phase flow except that the calculated permeability is the effective permeability to oil away from the wellbore. This finding was acknowledged by Per-rine, who also presented the equation for effective gas permeability* as Since Eqs. 1 and 2 contain no terms influenced by fluid compressibility, no distinct problem should develop in calculating permeability from two-phase build-up curves. In regard to the calculation of static reservoir pressure from build-up curves in single-phase systems, the modified Miller, et al, method as presented by Perrine is briefly as follows. 1. From build-up curve data, PVT data for the reservoir fluid and the well spacing and sand thickness, calculate the climensionless shut-in time corresponding to the highest value of actual shut-in time (t, hrs) on the straight-line portion of a semi-log build-up curve. Dimenrsionless shut-in time is related to actual shut-in time by the relation, t- 0.000264 kt 2. From a graph of dimension less shut-in time vs dimensionless pressure difference (Fig. 1 1 ) find the value of dimensionless pressure difference corresponding to the value of 7 calculated under (1) above. Dimen-

By F. D. Patchen

Changes in the properties of partland cement upon the addition of fine-ground silica are discussed. Data were collected from formulations cured for periods up to 60 days at temperatures varying from 180" to 350°F. Compressive strengths, permeabilities and thickening times are compared. It is demonstrated that addition of find-ground silica in proper proportion results in a hydrated cement with superior properties above 230°F; i.e., early compressive strengths are higher and increase with additional curing, permeabilities are significantly lnrver and thickening times are increased. X-ray analysis of hydrated cement samples have been used to determine more fully the complex chemistry of these systems. Dicalcium silicate alpha-hydrate was found in all neat cements cured above 260°F. A 10 weight per cent silica addition produced a maximum amount of this phase. Xonotlite and tobermorite have been identified as hydration products at 320°F in systems containing 35 or more weight per cent silica. Formation of these components appears to be primarily responsible for the gain in strength and reduction of permeability observed after the addition of silica. INTRODUCTION For several years it has been recognized that loss of compressive strength occurs when portland cement is cured at a temperature above 250°F. This phenomenon has been called "strength retrogression". More recently it has been recognized that increased permeability usually is associated with decreased compressive strength at these temperatures. At curing temperatures above 300°F, these factors reach serious proportions. A compressive strength loss of 50 per cent between curing times of 24 hours and 14 days has been reported,' and permeabilities as high as 10 md have been measured in neat cements cured at 320°F for seven days.' Earlier investigators,' although unsuccessful in eliminating strength retrogression, stated ". . . .it appears possible that by the proper selection of additives for cement, strength loss with age at high temperatures can be either eliminated or considerably lessened". One solution suggested was the use of a pozzolanic material, hydrated lime, and a retarder. Menze15 in 1934 discovered that portland cement containing finely divided silica possessed high compressive strengths when the curing temperature was 350°F. The use of such a composition is now an established practice in the manufacture of steam-cured cement blocks. It is reasonable to assume that the same beneficial effect can be used advantageously in high-temperature oilwell cementing operations. Ludwig first mentioned the use of sand for this purpose. Later, a portland cement containing moderate additions of silica flour and retarded with CMHEC, a cellulose derivative. was recommended for high-temperature application." These formulations have been successfully employed in the field."'" This paper presents the results of a research program to test the efficacy of finely ground silica in increasing the compressive strength and reducing the permeability of oilwell cement compositions containing portland cement. Included also are X-ray diffraction patterns of powdered samples which have been used to determine some of the important chemical reactions occurring in these systems. LABORATORY PROCEDURES AND MATERIALS All compressive-strength test specimens were prepared and cured from a slurry in accordance with API RP 10B, with two modifications. A final curing pressure of 5,000 psi was maintained for a one- or three-day period; but, for further curing, pressures were reduced to the vapor pressure of water at the curing temperature. Also, the water content was varied in samples containing silica to maintain the slurry viscosity within a range of 5 to 15 poise as measured on a consistometer. Test specimens at 180°T were cured in a water bath at atmospheric pressure. At higher temperatures the specimens were cured in a steam-jacketed high-pressure curing vessel at 5,000 psi for a one- or three-day period. cubes cured for longer periods were removed from the pressure-curing vessel after 24 hours, sealed in small bombs containing water and placed in an aging oven.

By K. T. Koone, R. J. Blackwell

One of the more important problems to be solved in designing a miscible flood is related to the size of the solvent bank used. Size of the bank may be critical to economic success. Too large a bank loses money; too small a bank may deteriorate and fail to maintain the miscibility needed for high recovery. An important factor in deterioration of a small bank is permeability channeling. In a highly stratified reservoir, solvent speeds ahead in the more permeable zones and mixes laterally with fluids bypassed in adjacent, low-permeability strata. Numerical solutions have been obtained .for the differential equations that describe the movement of a slug through a two-layer system in which mixing occurs both in the direction of flow and transversely. The solvent slug is assumed to have the same density and viscosity as the resident fluid and the pushing fluid. These solutions have been verified by comparing them with similar concentration profiles obtained in the laboratory in a 36-ft stratified model packed with glass beads. The theoretical study revealed that when the dominant mechanism causing a bank to fail is lateral mixing the bank size needed for a given recovery may increase with length rather than decreasing as the square root of reservoir length, as suggested by one-dimensional mixing theory. From a comprehensive examination of the variables, a generalized correlation is developed that relates strata thicknesses, bank size, fluid velocity, mixing coefficients, system length and simple solvent-resident fluid phase behavior to the area miscibly swept. INTRODUCTION Miscible displacement, or solvent flooding, continues to receive widespread attention as a method for increasing oil recovery over that possible in conventional gas-drive or waterdrive projects. A basic economic requirement in the application of such processes is the use of as little solvent as possible. A basic physical requirement is that enough solvent be used to maintain miscibility. Economics places an upper limit on the size of a solvent slug, and physical considerations establish a lower limit. Consequently, the practicality of any given miscible process requires that the economic limit be greater than the lower limit imposed by physical requirements. Procedures exist for determining the economic limit; however, procedures for determining realistic minimum bank sizes exist for only special reservoir situations. In the past, bank size has usually been selected on the assumption of a piston-like displacement for which only longitudinal mixing is important. This assumption leads to the favorable conclusion that bank size, expressed as per cent of pore volume, is inversely proportional to the square root of length. Collins considered the problem of transverse mixing of solvent with fluids in bypassed zones with the assumptions that no forward mixing occurs and that the concentration is uniform in the permeable stratum of interest. 1 Lauwerier considered a mathematically similar problem in thermal recovery operations.2 Their work suggests the much less favorable conclusion that bank size could be directly proportional to the length or even higher powers of the length. This paper considers the physical behavior of a small solvent bank as it moves through a real reservoir, without imposing many of the restrictive assumptions of past treatments. To facilitate mathematical description, an idealized, two-layer model that permits mixing both laterally and in the direction of flow will be considered. A calculation procedure for solving the descriptive equations will be developed for a displacement involving fluids of equal density and viscosity. In addition, laboratory experiments designed to check the computational results will be described, and the coincidence of calculated and observed results will be discussed. The use of many solutions for a variety of bank sizes, strata thicknesses and characteristic system lengths to develop a usable correlation between

Jan 1, 1966

Earnings of engineers in the period 1956 to 1958 continued the upward trend observed in the previous survey interval, 1953 to 1956. The overall median (all graduates) was $6500 in 1953, $7750 in 1956 (a 19 pct upstep or about 6.5 pct annually), and $8750 in 1958 (up 13 pct from 1956 or 6.5 pct average yearly). The latter represents an increase from mid-1956 to mid-1958. For this same two-year span the Consumer Price Index rose 1.5 pct and the Average Gross Weekly Earnings for Production (Manufacturing) climbed close to 10 pct. Median earnings for the major classifications studied are presented in Table I. The increase in engineering earnings are not distributed equally among the various activity classifications or among the experience levels of the survey. Summary results of the changes of the median lines for the major divisions are presented in Table 11. Data in this table are approximations- dollars are rounded to the nearest $50 unit and percentages to the nearest full percentage.

Jan 1, 1959

By Louis C. Just, Robert L. Sandefur, Carl E. Williams

In 1981 Ertec Rocky Mountain, Inc. completed a significant development in contemporary planning support; MINEPAK was completed, tested on various properties and offered for license. MINEPAK was one of the first computer systems for ore body analysis and mine planning that - Was designed as an interactive and completely integrated system - Was portable so that it can run on many hardware systems - Was really user friendly - Can run on minicomputers and on some microprocessors - Was built around a data base management system MINEPAK was designed to be a completely general block modeller and it achieved that goal. Since it contained a gridded file type, surfaces could be easily modelled but the system needed extensions to allow layered deposits to be modelled with the same ease as block models. So COALPAK was designed. COALPAK is an extension as well as a modification of MINEPAK. A 'layer' file type was defined and retrofitted into the existing system, new software tools were developed for modelling layered deposits, and tools for strip mining were written.

Jan 1, 1983

No. 230. Two engineers, technical graduates, three to five years, experience. One to take charge of 'pyrite mining in Canada; the other to assist in the mining work at the head office in New York. Salary for the right man, $5000. No. 231. Two young engineers, preferably men who have just graduated from college who are looking for an opportunity to work up with a reputable mining company. Men who have had some practical experience will be considered. No. 232. Assayer. Wet analyses, principally of lead, zinc, sulphur and insoluble. Assayer will also have some mill sampling and experimental work in a new flotation installation, as well -as control of regular mill operation and development-work samples front the mine. $75 to $100 per month and board, according to experience of candidate. No. 233. Engineer to lay out, erect and operate calcium carbide and ferrosilicon plant in the State of Washington. One furnace, 1500 hp. No. 234. Professor of metallurgy for school of mines in western state. $3000 per year to man properly qualified for the work.

Jan 9, 1917

FROM north to south activity is picking up through- out the Labrador Trough-already shown to be one of the world's great iron ore provinces. Center of current activity and interest lies in the mid-southern part of the trough as drills, equipment, and . . . money start to pour into the area near Mt. Wright and Wabush Lake. First major announcement in the area came early this spring when J&L and CCI outlined an estimated billion-ton deposit for "future" operations. Later impetus came from rumored railway for US Steel's Quebec Cartier projects in the Mt. Reed area slightly to the south. As this issue went to press US Steel's request for bids on railway and hydroelectric construction, plus IOCC's decision to step up the time- table on its program in the Wabush Lake area east of Mt. Wright, triggered a flurry of other announcements involving many of the top U. S. and Canadian iron ore firms. Do not look for most of these place names in the average atlas . . . they aren't there yet, but they soon will be.

Jan 6, 1958

By J. K. Brooke, R. M. Dreyer

For mining engineers and geologists accustomed evaluating metallic mineral deposits, the problems inherent in determining the worth of non- metallic industrial minerals deposits for the chemical processing industry often comes as a rude shock. These difficulties lead to different, and often much greater, problems in financing the development of such deposits than would normally be anticipated for economic sources of copper, molybdenum, iron, nickel and other metallic minerals. The chemical processing industry is one of the two principal consumers of non-metallic mineral production, the other being the construction industry. In the last decade, the volume of industrial minerals consumed by chemical processers has in- creased by 30%, and further increases are forecasted. To satisfy this growing demand, many new sources of these minerals must be found and developed. For those of us who will become involved in such work, the following brief analysis of the major problems to be expected may be of help in developing a realistic approach to evaluating and financing such a deposit and selling the product to consumers.

Jan 8, 1962

Development of Technical Education for the Petroleum, Industry. By H C GEORGE (Min & Met, June, 260 2000 words) With a growth of 718 per cent in the petroleum industry from 1901 to 1931, there was a corresponding increase in the demand for technically trained men in the industry This was first met by increasing numbers of college graduates from the old established courses m chemistry, geology and engineering However, there began to be felt a need for scientists and engineers specially trained for the petroleum industry In 1912 the University of Pittsburgh established the first department in any university in the world that offered major work in petroleum engineering and petroleum geology In Europe, the first major work in petroleum engineering was offered in England in 1913 at the University of Birmingham The University of California and Stanford University offered major work in petroleum engineering in 1915 Since that time at least 10 other American universities and colleges have offered major work and at least 12 others are now offering some courses dealing with petroleum, and the petroleum industry.

Jan 1, 1935

By H. I. Aaronson

THE TTT-curve for the beginning of transformation in hypoeutectoid steels containing appreciable amounts of relatively strong carbide-forming alloying elements often exhibits a "bay" at intermediate temperatures. In many of these steels, proeutectoid ferrite is the initial product of the decomposition of austenite not only at temperatures above the bay but also in an appreciable temperature range below the region of the bay. Hultgren has postulated that ferrite formed above the bay, termed "orthoferrite", contains the equilibrium concentration of alloying element at temperatures above the eutectoid range, and the extrapolated metastable equilibrium concentration at lower temperatures. The ferrite formed below the bay, on the other hand, termed "paraferrite", was assumed to inherit completely the bulk alloy content of the austenite without regard for the compositional requirements of equilibrium. As shown schematically in Fig. 1, the two types of ferrite were taken to have different Ae3 temperatures and different C-curves on a TTT-diagram. Their different kinetic behaviors were thus considered responsible for the bay in the TTT-curve for the proeutectoid ferrite reaction in this type of alloy steel.

Jan 1, 1962

By A. Bruce Matthews

Of the many opportunities in the mining industry to invest funds to improve operations, there is always some limit in every company as to how much can be spent each year for the acquisition of capital assets. Generally, there are many more opportunities for investment than funds to make the investments. As such, one of management's goals is to select the most profitable of all the opportunities available. Each opportunity must be carefully analyzed for its potential percentage rate of return. This percentage return or return on investment concept is an accepted financial yardstick of business profit- ability. For today's mining engineers, this problem resolves itself in the job of determining how to in- vest most productively the cash that is flowing from their operations so that it will multiply in value. There are four basic types of capital investments: Strategic investments, such as selecting a plant site, are those that affect virtually all long-run plans of a company. Change in a company's product line and expansion of company facilities are two other types of capital investments.

Jan 3, 1963

By Kendall Y. Keuhey

The Mercur Mine, developed and operated by Getty Mining Company, is designed to process 3,000 tons/day of gold ore from the historic Mercur Hill mining district. The mill process involves crushing, grinding, and cyanide carbon-in-leach for recovery of gold from ores ranging from 0.08 to 0.10 oz/ton. During the mining of normal grade ore, a substantial tonnage of material containing 0.02 to 0.05 oz/ton is mined and would be available for heap leaching. Also, Getty Mining is developing methods to test and prepare lower grade material for heap leaching by rejecting a coarse rock fraction from the grinding SAG mill circuit. This lower grade fraction is suitable for heap leaching, and its removal will upgrade the regular mill feed. Other test methods are directed toward leaching techniques on some 4.0 million tons of tailings that resulted from roasting and/or cyanide leaching Mercur ores in the early 1900's. The natural carbons associated with the Mercur deposits require special treatment to reduce their gold adsorption effects when leached with cyanide.

Jan 1, 1984

By Thomas M. Drown

Theodore Dehon Rand was appointed Treasurer of the American Institute of Mining Engineers by the Council, at the Boston meeting of February, 1873, to fill a vacancy caused by the resignation of the treasurer who had been elected at the first meeting in Wilkes-Barre in May, 1871. He was elected by the Institute to this offce in the following May, and yearly thereafter until 1903. He often alluded with amusement to the abrupt way in which he was injected into this position, by my coming to his office and asking him to accept the appointment as Treasurer, on the ground that he was eminently fitted for the position by reason of his legal and business knowledge, his interest in geology and mineralogy, and more particularly because he was a neighbor of the person (to wit, myself) who was slated for the Secretaryship, and they could thus convenient.ly confer on Institute matters. He consented, on condition that the duties should not involve too.much additional work for him. This assurance was easily given, for the Institute then

Jan 1, 1904

By Paul T. Allsman

Passage of the Mining Act of 1866, superseded by the Act of 1872, was the first major entry of the Federal Government into the problems of mining. Such a law was necessary simply to help re- solve a number of disputes in mining. Now, however, a hundred years later, the extent of government involvement in the mineral industry often comes as a shock to the mining engineer who has reached management level. In fact, he has been poorly prepared for an understanding of the role of government in the industry and he becomes frustrated, even hostile. In our political system, private industry is responsible for producing minerals and the Government sees to it that production will be adequate for a peace-time economy and for any emergency. There have been great social and political changes since World War I1 with the result that the Government's participation in our society has steadily increased. A new dimension in business and government relations has been introduced which should be examined more closely.

Jan 5, 1966

By Michael B. Gross

A numerical study of the vulnerability of unlined tunnels in jointed rock has been performed with the STEALTH computer program, using the CAVS model for jointed rock. CAVS, for Cracking And Void Strain, is a constitutive model that can simulate the initiation/propagation of fractures and the slip along fracture planes in a jointed rock mass. The CAVS model is unique because it represents a spatially oriented approach to rock failure, rather than the traditional invariant formulation, and because the CAVS submodels for slip friction and slip-induced dilatancy are used to represent the weakening influence of joints, rather than applying ad hoc modifications to the elastic moduli of the host rock. The CAVS model, as embedded in the STEALTH computer program, has performed numerical simulations of tunnel collapse at high overstress levels. These calculations show that the ultimate strength of the tunnel depends strongly on the joint properties, and that the results of the calculations are in qualitative agreement with the observed data for collapse of a tunnel in tuff.

Jan 1, 1984

By A. M. Gaudin, D. W. Fuerstenau, M. M. Turkanis

SOLUBLE silver salts are effective activators for flotation of sphalerite with potassium ethyl xanthate as collector.' Since sphalerite takes up large quantities of silver ions rapidly," investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hydrosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Finally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure.

Jan 1, 1957

By J. E. Russell, Y. J. Wang

In this paper, we report the results of a study of the characteristics of Texas lignite based on a proximate analysis data base previously published by the Bureau of Economic Geology, University of Texas at Austin and the U.S. Bureau of Mines. The original impetus for this study was the desire to perform a parameter study in connection with the siting of potential underground gasification tests in Texas. A numerical model of the gasification process was available and required proximate analysis data, among other parameters, as input. If proximate data were available for a particular site, a prediction of the product gas quality could be made. However, in preliminary siting studies, it would be advantageous to know what the desirable characteristics of the lignite are, in order to target general areas for drilling. Consequently, a parameter study was in order. This paper presents the methodology required to systematically vary proximate analysis parameters and estimate the corresponding energy content for various group(or formation)-facies classifications of Texas lignite.

Jan 1, 1983