Search Documents

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By J. C. Williams

The operations described in this paper are those of the flotation plant of the Valley Forge Cement Co. at Conshohocken, Pa., and concern the use of a particular cationic reagent—namely, DP-243. The role of this reagent in this plant may be better understood by first considering the purpose of beneficiating cement rock in general and the specific problems at the Valley Forge plant. The ultimate purpose of beneficiating cement rock is to obtain a kiln feed of the desired chemical composition in a form suitable for the most efficient kiln operation. The chemical composition is governed by the type of cement to be made. Before government restrictions (the purpose of which is to simplify operations during wartime) limited the types of portland cement a manufacturer is permitted to produce, five principal types of cement were generally recognized by the industry. They are based upon chemical and physical specifications proposed by the American Society for Testing Materials, federal and other governmental agencies, state highway departments, water boards and other users of large quantities of cement. The physical as well as chemical specifications for any particular type of cement necessitate proper proportioning of the major components—that is, the silica, alumina, iron and lime—and it is necessary to establish and maintain definite limits for each in the raw mix. The manufacturer must then prepare a kiln feed of a composition that will yield a final product that will fulfill the desired specification. This step is further complicated for kilns using coal as fuel, by the amount and analysis of the ash introduced. The amount and nature of the dust lost during burning will also affect the composition of the kiln feed. The problem of preparing a kiln feed of the desired chemical composition is not a simple one, and it is the final product that governs the methods used to obtain such a feed. For example, in starting with a material deficient in lime for the mix sought, it may not be sufficient to raise it to the required lime content. The other constituents must also be present in the proper proportions. In some cases, it may be necessary to raise the lime content to a point greatly exceeding that of the final mix, then, by addition of one or more other materials lower in lime, obtain the mix. The rock used at the Valley Forge plant is a metamorphosed argillaceous limestone of the Jacksonburg formation, the same formation as that of the Lehigh Valley cement rock (which occurs approximately 50 miles north), and its oxide composition is similar to that of the latter. The only practical differences between the two are that, as a result of metamorphosis, crystallization of the Valley Forge rock is considerably coarser and it contains less carbon than the Lehigh Valley rock as well as slightly more magnesia in the form of magnesian mica. The calcium carbonate content of the various strata in the Valley Forge quarry ranges from about 65 per cent to over 85 per cent, the average for the entire quarry being somewhat under the requirement for manufacture of cement, which usually is from 75 to 76 per

Jan 1, 1947

By ARTHUR S. DWIGH

Discussion of the paper of W. W. NORTON, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August., 1914, pp. 1993 to 1999. ARTHUR S. DWIGHT, New York, N. Y.-Mr. Norton's chief argument is directed against the idea that the D. & L. sinter is any better material for the blast furnace than the H. & H. product. He supports this by citing two experimental furnace runs. Reducibility.-To discuss a furnace record like that quoted by Mr. Norton for the five days' run in August, 1912, is manifestly difficult for an outsider, but a possible explanation for the poor reduction on Furnace No. 5, smelting D. & L. sinter, may lie in the fact that both sets of furnaces carried the same fuel charges. Other things being equal, if 11 ½ per cent. coke was right for the furnaces smelting H. & H. product, it Was too much for the furnace smelting D. & L. product, as I shall endeavor to show later, and incipient overfire, accompanied by higher leads in slag and matte, was induced. It may sound like a paradox to say that excessive fuel sometimes produces poor reduction, but it is a sad fact. In certain plants where practically the entire charge to the blast furnaces receives a preliminary treatment by being sintered on the D. & L. machines the peculiarities of this problem have had to be very carefully studied, for serious metallurgical difficulties presented themselves when the change was first made to D. & L. sinter in large quantities. Some of these plants had blast pots before they had D. & L. machines, and many opportunities were afforded for comparative study of this very point. There is reason to believe that, clue to the long period of blowing and the higher temperatures developed in the pots from greater mass action, the iron in the H. & H. product is present chiefly as Fe203, perhaps in the form of ferrites, while in the D. & L. product the iron is present as FeO. The fuel charge in the blast furnace must be so proportioned as to exactly meet the chemical and thermic requirements of reduction and melting. If ally of these functions have been performed before the material enters the furnace, a corresponding allowance should be made or the fuel balance will be disturbed and bad work will result. One of the functions of the coke is to reduce enough metallic Fe for the matte requirements, leaving the remainder of the iron as FeO to go into the slag. In smelting almost any other material than D. & L. sinter the iron must-be reduced from the higher oxides, Fe203 or Fe304, to the protoxide, FeO, before a true comparative basis is reached. Experience has shown that with about one-half D. & L. sinter on the charge the coke should-be cut about 10 per cent. This theoretical benefit is borne out by the practical blast-furnace results on a large scale in numerous plants. In fact, wherever this very important factor is ignored the evil symptoms of excessive fuel will be indicated,

Jan 11, 1914

By H. R. Brannon, J. S. Osoba

The introduction of the scintillation counter into field use for gamma-ray well logging has provided a new tool with special utility for the deternzination of natural radioactivity of sediments. Previous subsurface gamma-ray measurements have indicated only the total amount of radioactivity of the sediments. With the scintillation counter, the relative amounts of the elements which emit gamma radiation can be determined. Sediments logged included 35 zones in wells located in the Teras Gulf Coast, East Texas, and West Teras. Although the data obtained from measurements made to date are not sufficient to evaluate the possibilities of spectral logging, it appears likely that spectral measurements will yield information of geologic value. INTRODUCTION Although variations in the natural radioactivity of sediments were recognized as early as 1909,1 the appli- cation of such variations to borehole logging was not made until almost 30 years later. A group of Russian workers in the early 1930's were successful in making crude measurements of natural gamma activity in an oil well borehole. The first practical gamma-ray logging system was developed by Howell and Frosch2 in 1939. Induced radioactivity, or neutron, logging appeared soon after the introduction of gamma-ray logging. After early work had demonstrated the potentialities of radioactivity logging, development of sensitive and stable logging equipment for field use followed, so that neutron and natural gamma logs are now run routinely and have proved to be extremely valuable in characterizing subsurface formations. Even though tremendous strides have been made in developing radioactivity logging, it is apparent that the ultimate in the method of logging has not been reached, for, until very recently1 in none of the commercially available logging systems has advantage been taken of the fact that gamma radiation is composed of a spectrum of rays, each ray having a distinct and characteristic energy. An individual gamma ray originates in a single element and has energy determined by the element. The inten- sity of radiation, or number of rays emitted from unit volume in unit time, is determined by the concentration of the element. If it were possible to sort out these gamma rays and assign them to their parent elements, thereby essentially analyzing for the elements, a wealth of new information descriptive of formation material and fluid content would be at hand. For example, if in natural gamma logging, the gammas due to potassium and to the thorium and uranium series were measured individually, data would thus be available on the concentrations of each of the three elements, adding materially to the information content of the log. In contrast, conventional gamma logs measure only a quantity proportional to the combined concentrations of uranium, thorium, and potassium. The naturally radioactive elements occur in sediments in concentrations dependent on source material of the sediment, and through their chemical characteristics, on conditions of deposition,' so that the individual concentrations may be diagnostic for particular formations. These concentrations, particularly if measured in situ, could lead to a powerful tool for correlation and for reflecting environmental conditions under which sedimentation took place. As a correlation tool, individual uranium, thorium, and potassium measurements

Jan 1, 1957

By J. R. Coulter, F. O. Case, H. G. Satterthwaite, B. Harden

During the two years that the Henderson plant has been in operation, a number of technical improvements have been made by the staff of Basic Magnesium, Inc., the effects of which were realized subsequent to the writing of the paper by Major C. J. P. Ball (p. 28j, this volume). Pellet Mix The process as originally installed required the use of peat moss in the mixture going to the chlorinators. This had to be imported from Canada at a considerable cost, and, besides being expensive, constituted a serious fire hazard in the dry climate of Nevada. Experimentation looking toward its elimination had been going on for some time and was actively pushed as soon as operations commenced. It was found that a pellet mix containing no peat, which would chlorinate at a satisfactory rate, could be cast as a fluid slurry, which would set up into a hard mass having the desired porosity. For carrying out this operation, equipment similar to that used in the manufacture of phosphate fertilizer at Anaconda, Mont., was installed and proved eminently successful. The dry materials, with peat moss and raw concentrates entirely eliminated, are mixed with magnesium chloride solution in two Pratt phosphate mixers and the resultant slurry is poured onto two 48-in. slowly moving rubber conveyor belts. By the time the slurry has reached the head pulley, the material has set su4iciently to be broken and sized as desired. The discharge from the casting belts is fed to the four rotary kilns in the preparation plant, where it is dried and coked to the proper degree for subsequent chlorination. With the peatless feed the capacity of the kilns was found to be about double what it had been before, so that the four rotaries suffice for a 10-unit operation, thus making it unnecessary to operate the extruders and tunnel kilns. In addition to saving the cost of the peat, the new system can be operated with about 85 per cent less labor than was formerly required in the preparation plant. The new pellet production system has also made it feasible to install centralized crushing equipment with suitable conveyors and a loading station. Containers of 8000 lb. capacity were substituted for small cubicles of 1000 lb. capacity which formerly were used for charging the chlorinators, and trailer trucks were substituted for the small trains originally provided for transportation from the preparation plant to the chlorinators. These changes resulted in a considerable saving in handling and transportation charges. Handling Molten Metal The molten magnesium originally was ladled from the electrolytic cells into small gas-fired brick-lined cars standing between the cell rows. From these cars the metal nes ium. into ''cheeses'' weighing from 150 to 300 lb. After solidification the

Jan 1, 1944

FRED TURRELL GREENE Fred Turrell Greene was born in Brooklyn, N. Y., Nov. 22, 1872. His father, William A. Greene, was born in Providence, R. I., and his mother, Angenora Semlear, was born in Brooklyn, N. Y. Fred's early school clays were spent in Boston, whence his father moved to Canada in 1882. Attending first the Collegiate Institute in Toronto, .then the High School at Berlin (now Kitchener), Ontario, where he graduated, Fred progressed to the Toronto University and the Michigan College of Mines, at Houghton, where lie graduated in 1897. He secured employment almost immediately at Butte with the engineering force of the Boston & Montana Consolidated Silver Mining Co., under Chas. S. Batterman. In 1899 he went to Rossland, B. C., where he spent more than a year as mining engineer and assistant superintendent of the War Eagle Consolidated Mining and Development Co. and the Center Star Mining Company Ltd. Returning to Butte in 1900, he acted as assistant geologist for the Anaconda Copper Mining Co. until 1906, when he filled a similar position in St. Paul with the Great Northern Railway for about two years. From 1908 until his tragic death on Christmas day, 1917, his headquarters were in Butte, where he enjoyed an excellent reputation -as consulting mining engineer, with a rapidly widening circle of clients. During the past four years he had been consulting engineer for the Elm Orlu and other mines controlled by Hon. W. A. Clark, and was in charge of underground developments and law-suit preparations for the celebrated apex case between the Elm Orlu and the Butte & Superior companies. At the time of his death he was in charge of similar work for the Utah Metals Co., in connection with their mines at Bingham, Utah. He was also for some years active in the Coeur d'Alenes, as consulting geologist for the Federal and other companies there, and was considered an authority on this as well as the Butte district. Mr. Greene was unmarried, and is survived by his parents, a younger brother, who is in the army, and one sister, Mrs. James A. Hatch, of New York. Some of the most important and valuable ideas regarding the nature and origin of copper ores have originated in Butte, since that district is not only one of the greatest examples of mineralization known in any land, but has gone through a long course of mining litigation, and was, one of the first to be studied intensively by geologists. In connection with the early investigations, as well as with the most recent in that camp, Mr. Greene played an important part. His conscientious devotion to his duties and his intelligent handling of the problems presented for solution sufficiently explain the esteem in which he was held by his employers and his professional associates.

Jan 5, 1918

We the undersigned, being all persons of full age and citizens of the United States and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, as provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining and Metallurgical Engineers, Incorporated, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences, connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. II. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the undersigned are all members of said Council as the same was constituted on the 29th day of December, 1904. III. That on said last-mentioned date a regularly called meeting of said association was held at its office in the Borough of Manhattan, City of New York; that thirty days before such meeting notice of the intention to incorporate said association was given by mail to each member thereof whose residence or post-office address is known; that at said meeting the following resolutions were offered, seconded and duly adopted by the unanimous vote of all its members then present, to wit: "Resolved, That it is the sense of the members and associates of the American Institute of Mining Engineers in general meeting assembled that it is desirable and necessary for the well being of said association and its members and for the furtherance of the objects for which the same has been formed, that said association incorporate under the Membership Corporations Law of the State of New York; "And Further Resolved, That the Members of the Council of this Association, or a majority thereof, be and they hereby are authorized, in accordance with the provisions of Section 5 of Article I. of the Membership Corporations Law, to incorporate this association for the same purposes for which it has been organized and conducted, in the manner provided in Article II. of said law;, "And Further Resolved, That the name of said corporation as hereby adopted by this meeting shall be American Institute of Mining Engineers; "And Further Resolved, That the said incorporators shall be named in the Certifi¬cate of Incorporation as directors of such corporation until its first annual meeting,

Jan 1, 1940

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By C. E Shoenfelt, Gail F. Moulton

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By David R. Mitchell

The mineral pyrite (or marcasite) occurs in coal beds as balls, lenses, veinlets and bands. Several million tons are wasted annually on the refuse dumps from coal mining and coal-preparation activities. Sporadic attempts have been made in the United States to recover this pyrite for manufacture of sulphuric acid but only a few plants have succeeded in recovering it on a commercial scale. Several chemical companies in the East became concerned about supplies of pyrite early in 1943, but by late summer of that year the situation had eased. If for no other reason than national security and self-sufficiency during wartime, methods of recovering pyrite from coal-mine refuse should be worked out and made available to coal-mine operators who are potential producers of pyrite. Eastern sulphuric-acid plants are particularly likely to have their sources of raw material blocked by war conditions, so that special studies to determine where supplies of pyrite can be obtained for these plants from inland sources are desirable. Davis's1 summarization of conditions during World War I gives the following facts: During those years, the shortage of pyrite became acute. Shipments of hand-picked pyrite were made from a number of coal mines in Illinois, Indiana, western Kentucky, Ohio and Pennsylvania. A mechanical concentrating plant for sepa- rating pyrite from picking-table refuse was built at Danville, Ill., and operated for several years, and a small pyrite-concen-trating plant treating washery refuse near Gillespie, Ill., operated for several months in 1918. The Consolidation Coal Co. of Fairmont, W. Va., constructed and operated a sulphuric-acid plant using pyrite recovered from coal-mine refuse. The U. S. Bureau of Mines during 1917-1919 made a comprehensive survey of pyrite-production possibilities from coal mines and estimated that there was a potential yearly production of 435.000 tons from Ohio and Pennsylvania and 928,000 tons from Kansas, Missouri, Iowa, Illinois, and Indiana mines. This estimate included only mines that could produce one per cent or more of their coal production as pyrite containing a minimum of 40 per cent sulphur. PyRite Production According to the Minerals Yearbook,2 approximately 660,000 long tons of pyrite was produced in the United States in 1941, with an average sulphur content of 42 per cent. The average value f.o.b. mines was $3.09 per long ton. Spanish pyrite, 48 per cent sulphur minimum, was quoted at 12 cents a unit c.i.f. U. S. ports, equal to $5.76 a ton for shipments of minimum sulphur content. Most of the pyrite produced in the United States is obtained as a by-product in the dressing of copper and zinc ores. Metal mines in the East making pyrite concentrate for the market or use in company-operated sulphuric-acid plants

Jan 1, 1944

By B. H. Caudle, A. B. Dyes, R. A. Erickson

The study of the influence of fluid mobilities on the sweepout pattern resulting from the injection of gas or water has been extended to cover the production period which follows breakthrough of the injected material. Mobility ratios over the range common in field operations (0.1 to 17) were studied for several pattern floods (five-spot, staggered, and direct line drive). The experimental data required for these studies were obtained by the use of the x-ray shadowgraph technique using miscible oil phases of different viscosities in porous plate mode1s of a reservoir element. From the shadowgraph pictures obtained before and after breakthrough of the injected fluid, flowing ratios at the producing well and cumulative volumes injected were calculated. The method for applying such data in predicting field behavior is illustrated for a water flood of a five-spot. For this case a range of mobility ratios of 0.5 to 5.0 results in: (I) nearly complete (95 to 100 per cent) sweepout pattern efficiencies at abandonment conditions, (2) production after breakthrough being responsible for as much as one-third of the total recovery at the lower mobility ratios, and (3) a twofold variation in the operating life of the reservoir. In determining the merits of a secondary recovery operation, the fraction of the reservoir which is ultimately to be swept by the injected fluid is of major importance. Because of its significance a large amount of research has been applied to the study of areal sweepout efficiency. Muskat, Wyckoff and Botset1,2 have presented the classic analysis of the pattern efficiency at breakthrough for several injection patterns in which the mobility of the fluids ahead of the injected phase front was equal to the mobility of the fluids behind the front. Aronofsky3 as extended this analysis of recovery at breakthrough through numerical computations and by the stepwise use of the potentiometric model to include the effect of different fluid mobilities ahead of and behind the invasion front on the line drive performance. Fay and Prats' have also employed numerical computations to show the influence of one other condition of fluid mobilities on the five spot flood. In a previous paper' a new method of attack on this problem which employed x-ray and porous plates was described. At that time experimental results were also presented which described the effect of fluid mobilities on the reservoir area contacted by the injected fluid at breakthrough for the five spot and direct line drive patterns. Most of the literature pertaining to sweepout pattern efficiency has emphasized the pattern which is obtained at breakthrough of the injected phase. The increase in the sweepout pattern which occurs after breakthrough

Jan 1, 1955

By Gail F. Moulton, C. E. Shoenfelt

Proven and developed oil reserves, and productive capacity increased during 1943 in the fieids of the Rocky Mountain region. Oil production during the year was nearly 45 million barrels, or slightly less than in 1942. The rate of production at the start of 1944 was slightly less than at the start of 1943. Pipe-line projects scheduled for completion during 1944 should permit a substantial increase in the rate of production. Wildcat exploration was more extensive in Montana during 1943 than in other states in the region. The results of wildcat drilling were unsatisfactory, although new oil fields were discovered on the Gebo, Little Buffalo Basin and Steamboat Butte structures of Wyoming, the Gage anticline of Montana, and the Clark Lake structure of Colorado. The area of the structures on which the discovery wells were drilled is known to be considerable, but further drilling is required to determine the importance of these fields. The most important increase in proven reserves resulted from the drilling to newly discovered deeper producing formations in the Elk Basin and other fields of the Big Horn Basin area of northern Wyoming. Lack of a market and unfavorable prices for heavy black oils had prevented complete exploration of favorable areas in the Rocky Mountain region for many years. In particular, the effect on further exploitation of the Big Horn Basin area had been quite serious. The increased demands for all oils created by the war and an increase in price in February 1943, combined later with Government approval of construction of pipe lines from the Big Horn Basin area to the Billings and the Casper districts, provided a basis for undertaking a drilling program. The important additions to reserves were made by drilling in previously discovered fields. The newly discovered fields resulted from drilling on favorable structures which had been known for several years. A continuation of the favorable results obtained during 1943 seems possible only if further testing of the newly discovered fields is satisfactory and if drilling on less favorable known structures or geophysical prospects results in the discovery of new fields. The amount of drilling in the Rocky Mountain states of Colorado, Montana and Wyoming, was about the same during 1943 as .in 1942. However, owing to the fact that a number of wells of large potential production were completed in the Elk Basin field, the total initial production of the prodicing wells was- nearly twice as great for 1943 as for 1942. Explorational activity at the end of 1943 seemed to be directed to geophysical methods, which are required to discover structures hidden beneath the rocks of Tertiary age in the Powder River and other large sedimentary basins. It is in

Jan 1, 1944

By John Chipman, Carl F. Floe

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Sage B. H., Lacey W. N., G. W. Billman

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By Sage B. H., G. W. Billman, Lacey W. N.

The composition of the coexisting phases in the methane-ethane-n-pentane system was determined at 100°F. This was accomplished by withdrawing samples of the coexisting phases under isobaric-isothermal conditions. The relative amount of each of the components present in the liquid and gas phases was determined by conventional analytical fractionation methods. The phase behavior of this system approximates that estimated from generalized correlations which take into account the influence of the nature and amount of each of the components present upon the equilibrium. It was found that for particular pressures and temperatures the equilibrium constant of each of the components was influenced significantly by the composition of the system and this effect was more pronounced at the lower pressures for methane than for the components of greater molecular weight. However, at the higher pressures approaching the maximum two-phase pressure for the system at this temperature the composition markedly influences the equilibrium constants of all the components at a particular pressure and temperature. The results of this study are presented in graphical and tabular form. Introduction The phase behavior of many of the binary systems containing parafin hydrocarbon components from methane through n-pentane has been investigated during recent years. In addition the compositions of the coexisting phases in mixtures of crude oil and natural gas have been studied.' However, these results do not establish the influence of the nature and amount of the other substances making up a multi-component system upon the gas-liquid equilibrium constant of any one component. A preliminary correlation on the basis of values for binary systems was made2 utilizing such experimental information as was available. However, there is need for much additional information regarding behavior in systems containing more than two components. Study of the phase behavior of ternary systems offers a feasible attack upon the determination of the influence of composition as well as of pressure and temperature upon the several equilibrium constants concerned. An investigation of the phase behavior of the methane-propane-n-pentane system at 100°, 160°, and 220°F was reported.".' This work served to illustrate the marked influence of concentration of the other components upon the equilibrium constants. Variations of as much as 50 pct in the equilibrium constants for methane for fixed temperature and pressure were observed in regions remote from the critical state. Likewise there was a marked variation in the equilibrium constants of propane and n-pentane as a result of changes in the composition. These results indicated the desirability of investigating additional ternary systems. The present paper deals with a study of the methane-ethane-n- pen-tane system at 100°F, which is similar in many respects to the work upon the meth-ane-propane-n-pentane system cited above.

Jan 1, 1948

By Carl F. Floe, John Chipman

A year ago the authors published a paper on the solubility of sulphur dioxide in molten copper.l The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: 6Cu(l) + SO2(g) = Cu2S (in Cu) + 2 Cu2O (in Cu) [I] _ (CU2S)(CU2O)2 K = (Cu)6(Pso2) [2] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above 100 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu2O and CU2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of so2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. Experimental Methods The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Irving Lipkowitz

While the light metals are recognized generally as a distinct group in technical literature, economic classifications and data usually still treat them as part of the nonferrous group of metals. However, the economic characteristics of the light metals also differ markedly from those of other nonferrous metals. The distinctiveness of the light metals, as, a group and individually, becomes evident when their growth, since World War II is compared with that of other metals, as in Table 14.3.1. The growth of light-metals production has been much sharper than that of other metals. A weighted average for the light metals shows an increase of 112% during the 1958 to 1968 period. This compares with a 62% increase in the "All Primary Metals" component of the Federal Reserve Board Index of Industrial Production. The contrast was even sharper during the next six years (1968-1974), with light metals production up another 50% as against a 21 % increase in the FRB Primary Metals production index. The most important reason, however, for considering light metals separately is the trend and pace of technological change and not their distinctive statistics. Technology both creates and demands increasingly sophisticated materials. As technology advances and as all the world makes more extensive use of advanced technology, the importance of the light metals is likely to accelerate rapidly. There may be a profound clue to the future in the fact that light metals were predominant among the materials used in the construction of the Apollo 11 spacecraft. In determining what materials to use for the spacecraft and its equipment, the National Aeronautics and Space Administration (NASA) has explained that it did not look to "some of the more exotic metals" and relied instead on "generally proven materials." Accordingly, it apparently used a wide variety of metals, including precious metals, rare earths, special steels, copper, and light metals. What seems particularly significant is that, in seeking performance, NASA relied as heavily as it did on the light metals. Materials breakdown estimates show that aluminum accounted for over 75% of the materials used, titanium for another 5%, and magnesium was also used. Thus, light metals accounted for over 80%' of the materials used for the Apollo 11 spacecraft. The light metals are also unique in their availability. They rank high in abundance among the elements in the earth's crust. Aluminum is the third most abundant element, after oxygen and silicon, with magnesium ranking eighth, and titanium ninth. Among the structural metals, aluminum is the most abundant in the earth's crust, iron is second, magnesium third, and titanium fourth. This potential availability of light metals provides strong incentives for continuing improvements in process technology, because of two major national problems: (1) there is

Jan 1, 1976