Search Documents

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Zinc difhsions in gallium arsenide having surface concentrations as low as 5 x 10'' atoms per cu cm have been attained. A multiple-difhsion sequence is employed during which zinc enters the gallium arsenide from a silicon dioxide film in a solid-to-solid diffusion step. The technique is illustrated for the case of a zinc surface concentration of -1 x 1017 atoms per cu cm and a junction depth of 1.2 p. Radiotracer measurements of -0.1-p layers of gallium arsenide are used to delineate the resulting profile. A diffusion coefficient for zinc in pyrolytically deposited silicon dioxide is reported. ZINC is frequently used as an acceptor impurity in gallium arsenide. As examples, p-n junctions are formed using zinc-diffused layers in solar cells, lasers, and varactor diodes. For these purposes surface concentrations of 10'' to over loz0 zinc atoms per cu cm are desired and readily obtained from a vapor source. Diffusion of zinc into gallium arsenide to yield surface concentrations of about 1017 atoms per cu cm, however, is more difficult. For instance, oldstein' reports that large changes in the vapor density of zinc produce only small changes in surface concentration. Such low surface concentrations are necessary in forming the diffused base of a gallium arsenide double-diffused n-p-n transistor in order to obtain an adequate emitter efficiency. An alternative approach to zinc diffusion which can provide reduction in surface concentration of several orders of magnitude is the introduction of the diffusant from a solid source. This can be conveniently accomplished by using oxide films of the type generally employed for selective diffusion masking. Such oxides also serve to prevent the dissociation of the gallium arsenide surface at the high temperatures of diffusion. DIFFUSION PROCEDURE Fig. 1 illustrates the diffusion sequence which is employed for obtaining zinc surface concentrations in the range from 5 x lom to 1 X 10" atoms per cu cm. The description of technique will be given for the instance of -1 x 1017, which is typically utilized in double-diffused gallium arsenide transistor investigations at this laboratory. Tin- or germanium-doped gallium arsenide wafers drawn from crystals grown by horizontal Bridgman or Czochralski techniques are used, with bulk concentrations ranging from 1 to 3 X 10" carrier atoms per cu cm. Each wafer is chemically polished on the (iii) arsenic face using a mixture of five parts concentrated sul-furic acid, one part water, and one part 30 pct hydrogen peroxide at room temperature, followed by rinsing in deionized and quartz-distilled water. Pyrolytic silicon dioxide was chosen as the oxide coating because of the high quality of the films obtainable, the ease of their preparation, and the excellent control over film thickness and uniformity.

Jan 1, 1964

By W. C. Ellis, M. E. Fine

In the iron-cobalt system there are several property-composition relationships of theoretical importance. The alloys are ferromagnetic exhibiting a maximum saturation at approximately 33 at. pct cobalt;' the interatomic distances at room temperature show large positive deviations from Vegard's rule;2 and in the region of 50 at. pct cobalt there is an order-disorder transition2 which has a large effect on other properties. The thermal expansion data for the system have been reported only from room temperature to 100 C and for this temperature range a minimum in coefticient in the rcgion of 50 at. pct cobalt is well established.3,4,6 This paper reports the expansion properties in the iron-cobalt system for temperatures from 30 to 850°C, shows the correlation with other physical properties, and proposes an explanation for the tcrrelation. Experimental Procedure The thermal expansivities of iron-cobalt alloys in 10 pct steps in composition were determined from 30 to about 850°C. The major series of alloys was prepared by induction melting from Armco iron and cobalt rondelles with the addition of about 0.6 wt pct manganese. This series was supplemented by three compositions: high purity electrolytic iron, high purity electrolytic cobalt, and an alloy of 52.1 wt pct cobalt prepared from the high purity electrolytic iron and electrolytic cobalt by vacuum-melting. The compositions of both series of alloys are given in Table I. The specimens for measurement were prepared from the cast ingots by first hot-swaging followed in most instances by cold-swaging to 0.180-in. diam rod. Some alloys in the region of 5c pct cobalt, because of inherent cold-brittleness, were swaged hot to the final diameter. The expansion specimens were approximately 2 1/2 in. long with flat-ground and polished ends. Before measurement they were annealed in hydrogen for I hr at 900°C. In the apparatus used for the thermal expansivity measurements (Fig I), a modification of that designed by Hidnert and Sweeney,? the differential expausion between the specimen and vitreous silica was measured by a dial micrometer reading to 0.001 mm. An invar fixture supported the dial gauge, and this fixture, in turn, was connected to a split invar collar which supported the outer silica tube. A pyrex "T" was placed over the outcr silica tube and was sealed to the invar collar by Apiezon Q sealing compound. A movable hollow vitreous silica rod which rested on top of the test specimen slid through a flexible rubber diaphragm cemented to the top of the pyrex "T." The specimen rested On a vitreous silica pedestal fused into the outer tube and was kept centered by a silica sleeve. A nonoxidizing atmosphere was obtained by admitting hydrogen into the

Jan 1, 1949

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,' Dahl and Pawlek,' and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By J. J. Arps, T. G. Roberts

Since the introduction of the relative permeability concept in the middle thirties1,2 various investigators have shown3,10,11,12,15 how the basic equations for the flow of oil and gas through porous media can he utilized to compute the recovery from depletion type or solution gas drive type reservoirs under certain conditions, when the necessary physical data pertaining to the reservoir rock and its reservoir fluids are known. In the study by Muskat and Taylor" in 1945, the effects of viscosity, gas solubility, shrinkage, and the permeability-saturation characteristics of the producing formation on the production histories and the recovery of gas drive reservoirs were analyzed. Each parameter was varied a limited number of times, while keeping the others constant. The work was not carried to the point where the data could be used directly to estimate the primary recovery in those cases where certain rock and fluid characteristics were known or could be assumed. Since the publication of this classic study, the work by Beal in 194616 and Standing in 1952'" has established general correlations of oil viscosity and shrinkage with gas solubility and oil gravity. In addition. a considerable number of relative permeability relationships for different types of reservoir rocks has been published2,5,13,17,19,20. Also, the burden of the numerical work required in the solutions of the differential equation has. during the last few years, been greatly reduced with the availability of modern electronic computing facilities. The purpose of this paper is therefore to present the results of a large number of such recovery computations covering the normal range of variation of the main parameters such as the type of rock, the API gravity of the oil, and the amount of gas in solution. As is to be expected, the ultimate recovery is found to increase with the oil gravity. except for the higher solution gas-oil ratios. Within the normal range of solubilities, the ultimate recovery generally appears to decrease with the amount of gas in solution for the higher oil gravities, and to show a slight increase for the lower oil gravities. Intermediate oil gravities seem to fall between the two trends. The type of reservoir rock, as identified by its relative permeability relationship, appears to have a very pronounced effect on the ultimate recovery. In general, sands and sandstones show higher recoveries than limestones and dolomites, although certain intergranular limestones seem to show a higher theoretical recovery than unconsolidated sand. The recovery from sands and sandstones generally decreases with increasing cementation and consolidation, while the recoveries from limestones and dolomites are highest for the intergranular type and lowest for the fracture type porosity.

Jan 1, 1956

By E. G. De Coriolis

THE development of huge production facilities and of new or improved processes for manufacturing magnesium from its raw sources has been an outstanding achievement of this war. Furthermore, at least one new method has reached a stage of pilot production that offers promise. Its potentialities seem to indicate that a reduction in cost and simplification or elimination of problems incident to the use of at least one of the present processes are quite within the realm of possibility. Although magnesium of very high purity (99.9 per cent and higher) is obtained, and the rate of recovery reasonable (60 to 70 per cent), the ferrosilicon reduction process is open to a serious objection, which at the time its use was proposed was thought to be sufficient to raise some doubts as to its success, at least on a high production basis. The temperature range at which the reaction is carried out-namely, 2100° to 2150°F.-is very close to the failure temperature of the material of which the retort is made. It is so close that for a time it was assumed it might make commercial use of the process an impossibility. However, at the time under discussion, the demand for magnesium was so great that it was felt by those who had to go ahead and produce this essential metal that the emergency warranted their taking a chance on this process. Subsequent developments have fully justified the soundness of their decision. Fortunately for the war effort, when the plants were put into operation it was discovered that although the retorts did collapse in rather short periods of time, as predicted, they could be blown back into operable shape by application of high-pressure air. This practical method of operation so relieved the situation that the problem disappeared. Nevertheless, if the process had not been successful, or the production of magnesium by the electrolytic process had not been able to keep pace with demands, our war program would have been seriously impaired. "FIRELESS COOKER" PROCESS For this reason a program was set up and assigned for the development of a new method that had been suggested to the War Production Board in 1941. It is believed justifiable in terming the method "new" for several reasons: (1) while utilizing the same (ferrosilicon) process as the Pidgeon, hence involving similar reactions, the type of retort or furnace is essentially different, (2) the method of operation, reaction temperatures, etc., differ materially, and, most important of all, (3) the problems to be overcome in making the process successful were not and could not have been anticipated by anything previously known about the Pidgeon process. As will be shown later, the briquetting process, the condenser, the furnace lining

Jan 1, 1945

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By Owen Thornton

Recently equations have been presented by Rose and Bruce' and by Rose², showing how the relative permeability of a reservoir rock may be determined from the capillary character of the rock. In particular, equations were developed to show the relationship between capillary pressure and the effective permeability to the wetting phase in a poly-phase flow system. The equations are as follows (nomenclature the same as in the Rose and Bruce paper) Rose and Bruce assume that the average length of path (L,), which the wetting fluid follows in flowing through a porous media is independent of the saturation to the wetting phase, so that 1 is a constant dependent only on the k rock, and the permeability to the wetting phase is a function of the saturation and of the capillnry pressure: In measuring the flow of ekctric current through partially saturated core samples, it has been observed that the electrical resistance usually is not a simple linear function of saturation. This fact indicates that the average length of path in the flow of electric current is not independent of saturation, but rather that the tortuosity of the path depends upon the average saturation to the conducting fluid as well as upon the characteristics of the rock. itself. Inasmuch as the flow of fluid and the flow of electric current in many respects are analogous, it may be indicated further that the length of path for fluid also may not be independent of saturation. The following relationship can be derived to express the resistance to flow of electric current through a core sample partially saturated with conductive wetting phase, the non-wetting phase being non-conductive: where L is the average length of path followed by the current in flowing through a length L of partially saturated core, where L is the length of current path when the core is fully saturated, and where Rs and R, are the specific resistivities of the partially saturated and saturated core sample, respectively. It will be noted that R., the specific resistivity of the core sample when S, = 1.0, is equal to the "formation resistivity factor"' multiplied by the specific resistivity of the saturating fluid. If it be assumed that the average lengths of path for fluid flow and for the flow of electric current are the same, then equation (5) may be combined with equations (l), (2) and (3) to give the following relationship: The above equation suggests including a correction for tortuosity when calculating the relative permeability of a reservoir rock to a wetting phase. The correction factor may be obtained from the resistivity-saturation relationship. For instance, the following calcu- lations are obtained for the unconsoli-dated sands described by Leverett Kw Kw Sw R°/Rs Pt/Pc¹ (Calc.) (Obs.) 0.30 0.08 0.88 0.02 0.0 0.40 0.16 0.94 0.06 0.04 0.50 0.27 0.97 0.14 0.11 0.60 0.40 0.98 0.26 0.21 0.70 0.53 0.98 0.39 0.35 0.80 0.68 0.99 0.57 0.54 0.90 0.84 0.99 0.77 0.76 1.00 1.00 1.00 1.00 1.00 It will be noted that the agreement between the calculated points and the observed data is rather good. Further investigation of the above method for obtaining relative permeabilities may be merited. For many sands within specified ranges of saturations the following relationship has been found to hold approximately': — =SW"......(7) Rs The exponent n in the above equation has been found to equal two for many sands so that equation (6) reduces to the following: The writer acknowledges the permission of The Texas Co. to submit this note for publication. 1. Walter Rose and W. A. Bruce—Jnl. of Pet. Tech., Vol. 1, No. 5, p. 127 (1949). 2. Walter Rose—Jnl. of Petr. Tech., Vol. 1, No. 5, p. 111 (1949). 3. G. E. Archie— -Trans. AIME, 146, 54 (1942). 4. M. C. Leverett— Trans. AIME, 142, 152 (1941). 5. M. C. Leverett—Trans. AIME, 132, 149 (1939).

Jan 1, 1949

By W. C. Thurber, C. J. McHargue

THE deformation textures of metals have been extensively studied because of both the practical implications in metal fabrication and the fundamental insight into the behavior of the metal during deformation. Most studies have been concerned with pure metals or solid-solution alloys and relatively little attention has been directed toward more complex alloy systems. Barrett' and Brick2 have summarized work on multiphase systems in terms of the relative ease of deformation of the phases. Thus, if the phases are deformed about equally, each develops its usual texture for the particular fabrication process. This behavior has been reported for Ag-Cu and Cd-Zn alloys3 and 62-38 brass.4 A dispersion of hard particles in a softer matrix interferes with the normal reorientation of the matrix lattice during deformation, thus distorting the texture or in some cases preventing its development. Increasing the amount of carbon in steel has been observed to increase the randomness of the ferrite5 and almost random textures have been reported for A1-12 pct Si eutectic alloy wires.6 It has also been noted that if the second phase is platelike, deformation causes the platelets to line up in a common direction. The present work concerns a quantitative study of the deformation textures in aluminum-uranium alloys containing 5 or 13 wt pct U. Alloys in this composition range are characterized by a pure aluminum matrix in which the intermetallic compound UA14, is dispersed. From a fundamental standpoint, this system affords the opportunity for studying the effects of a dispersed phase on texture development in an essentially pure metal matrix. Further, these alloys are commonly used as fuels for nuclear research and testing reactors, and a knowledge of the preferred orientation may be useful in evaluating physical and mechanical properties as well as response to fabrication. The deformation textures in sheets of aluminum (99.996 pct), Al-5 pct U alloy, and Al-13 pct U alloy were determined for reductions in thickness of 90 pct by cold rolling. The texture in an alloy rod of the latter composition which had been extruded at 455°C was also determined. It can be readily ascertained from the aluminum-uranium phase diagram that the 5 pct U alloy is hypoeutectic and contains 7.3 wt pct (3.4 vol. pct) UAl4. The 13 pct U alloy has the eutectic composition and contains 18.9 wt pct (9.4 vol. pct) UAl,; however, because of nonequilibrium solidification conditions, the typical eutectic microstructure was not developed. The alloys were prepared by open-air melting in graphite crucibles. The slab castings were cropped and cold reduced 90 pct in thickness on a two-high mill. The slabs were reversed after each pass. Although the uranium-bearing alloys exhibited edge cracking, they could be cold rolled to the desired thickness. Small coupons 1.5 by 0.75 by 0.1 in. thick were sheared from the center of the rolled plate with a major axis parallel to the rolling direction. To obtain a specimen of sufficient thickness for machining of the X-ray diffraction specimen, three coupons were laminated into a single three-ply sandwich with a suitable adhesive. Adhesives which could be cured at room temperatures were selected in order to prevent recrystallization during bonding. Bondmaster M-648 (Rubber and Asbestos Corp.) was used for the pure aluminum laminate and Armstrong A-6 (Armstrong Products Co.) was used for the alloys. The alloy for extrusion was cast in a cylindrical graphite mold! cropped and machined into a 3-in. diam by 4-in. long billet. This billet was preheated to 455°C, upset to 3.125 in. diam, and extruded on a 700-ton hydraulic press at a speed of 6 fpm through a flat-face, 1-in. diam die. The rod was quenched with a water spray as it emerged from the die. Pole-distribution data were obtained using the diffractometric method described by Jetter and Borie.7 A spherical X-ray diffraction specimen of

Jan 1, 1961

By H. Macpherson

Durhm has a well earned reputation for supplying some of the finest coking caals in the world. The caals, in general, vary in rank from 301 to 501/2. Durham has traditionally produced foundry coke for the major proportion of the foundries in Great Britah. Durham coals can be described as clean, soft coals, which yielded, with the old hand methods of coal getting, low ash small coal because the extraneous shale was normally harder than the coal and occurred in larger pieces. Under these conditions, with a plentiful supply of cheap labor, it used to be sufficient, at most collieries, to hand clean the large sizes of coal which could then be remixed with the untreated small coal to produce carbonization coals, ready for the coke ovens, at under 5 pct ash. With the introduction of mechanical methods of coal mining, the coal gradually required more cleaning. The first method adopted to resolve this problem was the introduction of pneumatic dry cleaners for the small coal. Although such machines had little effect on the fine coal (say below 1/8 in.), they could clean the intermediate sizes of coal. This, coupled with hand cleaning the larger sizes above 1-1/2or 2 in., resulted in a combined run-of-mine mixture below 6 pct ash, capable of maintaining the quality and reputation of the cokes produced. In more recent years, the intensification of mechanization and power loading, coupled with gradual exhaustion of the cleaner seams, has created the need for a more complete method of coal cleaning. This particularly applies in the fine sizes (say below 1/50 in.) which normally vary, under present day conditions, between 15 and 35 pct ash and are much too dirty to be included in the raw state in a carbonization mixture. This pronounced change has been accelerated because legislation controlling the dust conditions of mine airs for the prevention of pneumoconiosis has resulted in tk~e extensive use of water underground and a consequent increase in moisture content of the run-of-milie output. The presence of damp fine coal decreast the efficiency of prescreening and dry cleaners, so that this type of preparation for low ash coking coals is decreasing, although it is still used satisfactorily for industrial coals in the medium ash range. Table I shows the gradual increase in mechanization, the reduction in manpower, the increased use of explosives per ton of coal extraction, and the increase in the proportion of coal cleaned by mechanical means in Great Britain. Although similar figures are not available for Durham Div. until after the date of nationalization of the coal industry, it is probable that the increase in mechanical cleaning, particularly by dry cleaners, was more marked in the Durham collieries than elsewhere in the country. As dry clealiers were replaced by coal washeries in the Gritish ccal industry, no special attempts were made to recover the slurry, with the result that large outflows of dirty water were allowed, deposits of slurry came in to lagoons and neighboring streams, and a proportion of fine material was lost from the coking coal. This position, coupled with the higher moisture of the washed coking coal, resulted in adverse effects on coke oven throughputs and coke quality. It is now realized that the natural coal fines are an essential ingredient of coking coals in obtaining the correct coke structure in metallurgical cokes. This, together with economic pressure, led to the introduction of flocculation and filtration plants for the recovery of slurries, and later, when the ash contelits of the filter cakes were too high, to the introduction of froth flotation equipment. After this position had been reached, the tailings from the froth flotation pIants were, in many cases, still allowed to constitute an undesirable effluent. Recent legislation on river pollution has changed this picture; it is now necessary to provide a circuit which is completely closed so far as solids are concerned. The gradual increase in the coal cleaned by wet methods and froth flotation in Durham Div, is shown in Table 11. It is now an accepted feature of new Washeries that. froth flotation should be an integral part of the washing process from the initial installation of the plant.

Jan 1, 1962

By O. N. Carlson, H. A. Wilhelm, J. M. Dickinson

On the basis of microscopic studies, melting-point observations, and X-ray analyses, a phase diagram is proposed for the Cb-V system. A complete series of solid solutions is formed with a minimum in the solidus at 1810°C near 35 wt pct Cb. No compounds or intermediate phases were found in the system above 650°C. THERE is an ever increasing need for better structural metals and alloys for use in nuclear reactors. In addition to the normal properties of engineering structural materials, such as high temperature strength, resistance to corrosion, and fabric-abil~ty, the nuclear properties of the material must be considered. In a nuclear reactor it is important to conserve neutrons, so a material which removes these neutrons from the reaction excessively is considered to have unfavorable nuclear properties. In nuclear-reactor design the engineer must have nuclear as well as other data available on alloys in order to make a wise selection of materials. Due to the fact that many of the common structural materials have undesirable nuclear properties, it is vital that new alloys of metals having more favorable nuclear properties be investigated. Columbium and vanadium are both high melting metals, both exhibit resistance to chemical attack, and no great difficulty is encountered in fabricating them into desired shapes. With proper treatment both metals can be cold rolled extensively without failure. In addition they have desirable nuclear properties for certain types of reactors. Therefore, the alloys of columbium and vanadium should be of interest in the atomic energy program. Since an alloy-development program is enhanced by a knowledge of the phase equilibria of the components, this investigation was undertaken to establish the phase diagram for the Cb-V system. According to the Hume-Rothery rules for alloying,' the chemical similarity, crystal structure, and atomic-size factor are favorable for a complete series of solid solutions for this system. Both elements are in the same family of group V of the periodic table and thus are quite similar chemically. The crystal structures of columbium and vanadium are compatible for extensive solid solubility, since both have body-centered-cubic structures. The atomic diameters of columbium and vanadium are 2.85 and 2.62Å, respectively. This difference of slightly more than 8 pct is well within the 15 pct maximum difference allowed for extensive solid solubility. Experimental Procedures Source of Materials: Columbium powder and sheet trimmings were obtained from the Fansteel Metallurgical Corp. According to the manufacturer the metal contains less than 1 pct impurity. An analysis of the metal showed approximately 1800 ppm C in the powder while the sheet trimmings contained less than 500 ppm C. Spectrographic analysis showed minor amounts of Ca, Cr, Fe, Mn, Si, Ti, V, and Zr in both forms of the columbium. No commercial source of vanadium having the ductility and purity desired was available to the authors at the beginning of this investigation. As a result, all of the vanadium used in this study was prepared by the bomb reduction of vanadium pen-toxide with calcium employing the method reported by Long.' Yields of massive vanadium normally were about 80 pct. Chemical analysis of the vanadium prepared in this manner showed the presence of 200 to 500 ppm N and 800 to 1000 ppm C. Minor amounts of Ca, Fe, Mn, Si, Zr, Cr, and Cb were detected by spectrographic analysis. This vanadium metal was ductile and was cold rolled into 5 mil sheet. Annealing was not necessary during this rolling and the metal retained its cold-rolling characteristic after are-melting. Preparation of Alloys: The Cb-V alloys were prepared by melting pieces of vanadium sheet togethel-with columbium in the form of sheet or pellets of powder. The melting was carried out under argon in conventional arc-melting equipment employing a tungsten electrode and a water-cooled copper crucible. Each alloy was remelted three or four times, inverting the alloy after each melting in order to assure complete mixing. Alloys normally were obtained as round flat disks, weighed approximately 70 grams, and had roughly the shape of a disk 1 1/2 in. in diameter and 1/4 in. thick. Half of each alloy

Jan 1, 1955

By C. G. Dunn, P. K. Koh

THE primary recrystallization texture in cold-rolled silicon iron, which is the matrix texture for developing the Goss texture or the cube-on-edge texture by secondary recrystallization at temperatures near 900°C,1-5,21 has not been adequately described. Thus from the present available information, it is not possible to explain satisfactorily both the grain-growth selectivity of the matrix and the often observed magnetic torque curve, which itself provides some information on the texture. Also lacking is information on the special annealing texture that develops in this material when the annealing temperature is 1200°C or higher and the rate of rise to temperature is extremely rapid. From the work of May and Turnbull5 and from unpublished work, it was known that isothermal annealing near 1200°C tends to reduce the extent of secondary recrystallization and that a much weaker cube-on-edge texture results if appreciable normal grain growth replaces secondary recrystallization. Koh and Dunn6,7 have obtained additional information on complex primary recrystallization textures from further studies made after normal grain growth. In these instances the initial textures were retained during normal grain growth. A similar result reasonably could be expected in the present study except for the presence of a grain growth ihibitor1-5,8,9.21 and its tendency to allow only a few grains to grow. However, any information on the orientations of grains in the special annealing texture, even if far from representative of the initial matrix texture, would provide useful information on the nature of the matrix texture. In the present texture study the method of Newkirk and Bruce,10 which is based on the methods of Geisler" and Schwartz, 12 is used to obtain a complete (110) pole figure of the primary recrystallization texture. The high-temperature annealing texture is determined simply from the orientations of a large number of selected grains. The kinetic nature of the process that produces the annealing texture is treated elsewhere13 and it is shown that a form of secondary recrystallization with a very high rate of nucleation occurs during rapid annealing at high temperatures. EXPERIMENTAL PROCEDURE Commercial 0.014-in. cold-rolled silicon iron strip (3.16 wt pct Si), prepared by two stages of cold rolling with an intermediate short anneal, was given a decarburizing 3-min anneal at 800°C. Me-tallographic studies indicated complete recrystallization. Short-time anneals at 900° C and at higher temperatures proved that secondary recrystallization had not begun at 800°C, in fact, the short additional anneals were still in the induction period of secondary recrystallization. A rapid rise to an annealing temperature of 1260°C (2300°F) was obtained in a BaC12and NaCl fused salt bath. The structures that resulted from anneals in the range 12- to 1000-sec duration were relatively finegrained, even though the growth was a form of exaggerated grain growth13 or secondary recrystallization with a high nucleation frequency.= Many of the grains were large enough for an X-ray study using a 5-mil X-ray beam. A transmission Laue Camera and an optical-mechanical stage for moving the grains into the X-ray beam were used. A total of 325 grains were X-rayed in this manner and the grain orientations determined. Complete (110) pole figures were obtained for the primary recrystallization texture using CoKa radiation at 30 kv in the back-reflection range, such as (220) for (110) poles, as described recently by Newkirk and Bruce.10 The low voltage serves to reduce the spurious white radiation to a minimum. A filter of 0.001-inch iron foil was located in front of the detector slit for transmission and in front of the beam slit for back reflection. A new and improved specimen holder extended the useful tilting angle range for transmission to 70 deg instead of 60 deg as previously reported.' A torque magnetometer was used to obtain the magnetic torque curves for a number of l-in. diam disk specimens. RESULTS The (110) pole figure of the material after recrystallization at 800°C is shown in Fig. 1. The positions of the pole concentrations are found to be

Jan 1, 1961

By Gen-ichi Nakazawa, Masamichi Fujimori, Ichiro Doi

INTRODUCTION The major products of nickel industry in Japan are the electrolytic nickel (E-Ni), the ferro-nickel (Fe-Ni) and the nickel oxide sinter (NOS), totaling in production to 90 - 100 X 103 tons/year in terms of pure nickel content, and sharing approximately 20% for E-Ni, 10% or less for NOS, and the rest for Fe-Ni. The raw materials to be used for these products depend totally upon the imports from abroad; matte, the raw material used in the production of E-Ni, is from Australia and Indonesia; matte for the NOS is from Indonesia and New Caledonia; and garnierite, the raw material for Fe-Ni, is imported in bulk from New Caledonia, Indonesia and the Philippines. This report describes the acquisition of these raw materials, the production processes, trend of supply-demand, problem areas and the measures taken, and so forth, in connection with the nickel industry in Japan. ELECTROLYTIC NICKEL 1. History The nickel industry in Japan began in 1939 by the Sumitomo Metal Mining Co., Ltd. (SMM) with 150 tons E-Ni/month under the blast furnace smelting and the metal anode electrolysis. This was temporarily suspended after the end of last World War II, but resumed in 1952 with garnierite of New Caledonia as a raw material. Since then, the production capacity has been expanded incidentally to the increase of demand. However, since the smelting of garnierite contained about 2% nickel was very costly, the smelting process had been changed to smelt the briquettes of the mixture of garnierite and nickel sulfide concentrate imported from Canada and Australia. In 1975, this smelter was closed, and SMM's nickel refinery used matte from Western Mining Corp. (WMC) of Australia as a raw material. The refining process had been the metal anode one. The crude nickel oxide derived from roasting the high grade nickel matte had been melted and reduced with coke in the electric furnace and cast into anode. In 1970, a new refinery was constructed to produce 1,000 tons Ni/month under the matte anode process, and further, in 1976, the old refinery was converted into the matte anode process, thus resulting in the total production capacity of 1,690 tons Ni/ month today under the matte anode process. Shimura Kako Co., Ltd. began in 1951 to produce a little of E-Ni, and in 1955, they constructed a shaft furnace smelter with New Caledonian garnierite as a raw material to begin the E-Ni production under the matte anode process. Its monthly production reached 400 tons in 1957, but it discontinued its smeltering in 1963 to convert to the matte import from S. Le Nickel, WMC and INCO. In 1979, it changed the source of matte supply from the above to Soroako of Indonesia, discontinued the E-Ni production in 1979, and arranged for a total toll contract with Sumitomo. Meanwhile, SMM has developed a very distingished process for nickel-cobalt separation and refining by a solvent extraction method from nickel and cobalt mixed sulfide generated as a by-product in the nickel recovering process from laterite under the Nicaro process. Nippon Mining Co., Ltd. (NMC) also developed its own process. The plants under these processes were constructed in 1975, with the monthly production capacity of 230 tons of nickel and 130 tons of cobalt by SMM, and 300 tons of nickel and 110 tons of cobalt by NMC. SMM imports the raw material from the Marinduque Mining and Industrial Corp. of the Philippines, while NMC from Queensland Nickel Pty. Ltd. of Australia. 2. Production Status 2.1 Producers and materials Today, SMM holds the monthly E-Ni production capacity of 1,920 tons, of which 1,690 tons are from the matte anode process, and the remaining 230 tons are from the mixed sulfide as a raw material. NMC also uses the mixed sulfide as a raw material for a production of 300 tons/month. [ ] Most of SMM's raw material, nickel matte, is imported from WMC of Australia, partly using the Soroako matte from Indonesia. An example of material analysis is given in Table 1. Matte is a raw material for E-Ni and NOS, and the major sources of matte supply at present are Australian WMC and Indonesian Soroako, occupying ap-

Jan 1, 1982

By R. J. Lutton

Empirical data from 91 rock excavations have been used to construct a family of slope curves on a chart relating excavation height and inclination. The highest and steepest slopes from each excavation are plotted and connected by a line. The 31 1ines appear to establish one or two geometrical slope fields through which the curves are projected. The curves apparently represent a lumped eflect of many factors too complex to be considered individually. Important factors such as geological structure or ground-water conditions can dominate the picture, but where these factors do not overshadow others, the slope chart should be useful for estimating or checking optimum inclination. The U.S. Army Corps of Engineers (USAE) has been engaged since 1962 with the U.S. Atomic Energy Commission in a joint research program to develop nuclear excavation technology. The Corps is responsible for collecting the requisite data on engineering and construction problems associated with nuclear excavation. The ultimate objective is to develop a capability to use nuclear explosives as a construction tool on public works projects such as harbors and canals. The present study on empirical inclination-height curves for conventionally excavated slopes is an outgrowth of an investigation' sponsored by the USAE Nuclear Cratering Group on applicability of data from existing excavations in establishing guides for engineering judgment in crater excavation. Data were generously contributed by over 50 mining companies among other organizations. Inasmuch as several companies preferred that their contribution be anonymous, all data are treated so here. Some Factors Affecting Stability Many factors affect or are suspected of affecting the stability of excavated slopes, e.g., adverse structural orientation, degree of structural ordering, ground water, climatic conditions, mechanics of excavation, and plan-profile configuration. Such factors are lumped together in developing a slope chart. Obviously geological structure and ground water can overshadow all other factors. Where such is the case, the simplification of slope charts may give an erroneous picture (not conservative enough). A further complication results from the fact that the concept of stability may vary according to the use of the excavations. For example, slope adjustments that would be regarded as failure in a powerhouse excavation, might be tolerable in a mining operation. Mine slopes are continually being modified by further excavation, and instability that would develop in a similar permanent excavation slope over a period of years might not have time to develop in a mine. Inclination vs. Height Charts Charts of inclination vs. height for particular formations or conditions have been used in the past as an aid for designing excavation slopes. Some of these have been based upon empirical analyses of collections of data and experience. MacDonald" and Lane have presented slope tables and charts for excavated and natural slopes in relatively weak sandstone and shale. Coates' has shown an inclination-height chart for slopes in incompetent rock. Most organizations have developed slope design criteria which relate bench widths, heights, and inclinations to use in various rocks. Slope data collected in present studies can be similarly used to develop inclination-height charts; however, a plot of all slopes on such a chart shows very little because of the wide spread of the data. Reasons for the dispersion of points are: (1) many slopes are not carried at optimum inclination, particularly in mines where maintaining roadways and following irregularities of ore bodies are more important than achieving steep inclinations; (2) many engineers and geologists with varied backgrounds and viewpoints have been involved in designing these slopes; and (3) each slope is characterized by a unique combination of factors affecting stability and in turn optimum inclination. Significant curves can sometimes be constructed where the points can be grouped into related clusters from the same excavation. The essence of this approach appears when only two slopes from each excavation are considered—the highest slope and the steepest slope, connected by a line segment (Fig. 1). This reduces considerably the usable data because in many cases only one of these two slopes is available. Nevertheless, the concession seems justified. Construction of Slope Curves Ninety-one pairs of points and connecting line segments were assembled in this study. The line segments were assumed to approximate a geometrical slope field (Fig. 2), and a family of curves has been visually projected through to represent the slope field. It should be

Jan 1, 1971

By R. T. DeHoff, F. N. Rhines

The problem of determining the number of particles of a phase distributed randomly in unit volume c an opaque matrix from measurements made on random plane sections is closely investigated. A formalized derivation for the general case is presented. Applications of this formal result are made to specific types of aggregates dispersed in a matrix; circles, particles with flat circular ends, cylinders, and constant shape aggregates of ellipsoids of revolution. Quantitative measurements of the average geometric properties of these aggregates are developed. In 1953 R L. ullman' developed a technique for determining, from measurements made on random plane sections, the number per unit volume, Nv, of particles imbedded in an opaque matrix. Using meas urements previously developed for volume fraction, vV,' and surface area per unit volume, .SV,= he was able to determine average volume, average surface area, and average dimensions of particles, independent of size distribution, for spheres and circular disks,' as well as for uniformly sized cylinders of any axial ratio.4 The technique is mathematically rigorous for the cases studied. Recent studies of this problem have yielded rigorous solutions for the general case of cylinders, permitting evaluation of NV independent of size distribution and with all axial ratios intermixed. Generalization to shapes having flat, circular ends has been deduced. A solution has also been obtained for the ellipsoid of revolution, independent of size distribution, but requiring a constant axial ratio in the generating ellipses. In the following derivations, as in Fullman's work, it is assumed that the problem is purely a combination of geometry and probability theory,that is,eithe the particles to be measured are imbedded randomly in the matrix, or a sufficient number of random plane sections are taken to make the sample representative. A relationship exists between the number of par- ticles of a given size and shape that may be situated in unit volume (Ny) and the number of intersections a random plane can be expected to make with these particles (Na). It is the purpose of the following section to derive this relationship. The probability of Intersecting Convex Bodies. Consider a convex, closed surface, that is, one for which no two surface normals point in the same direction, situated at some arbitrary position and orientation in a cube of material that is one unit long at each edge. It is not necessary to assume that this surface is symmetrical. Let planes be constructed in the cube parallel to the top face and at random distances from it. Those planes which lie between the two planes which are just tangent to the top and bottom of the surface will intersect it. The probability that a plane will intersect the body may be defined as the limit of the fraction of planes that lie between the two tangent planes as the total number of planes constructed becomes infinite. This fraction, in the limit, is equal to the distance between the two tangent planes, DV, divided by the total length over which planes are constructed, which has been taken as unity. If the body is now rotated to a new orientation, applying the same argument, the probability of intersection is again numerically equal to the distance between tangent planes. Let DV ($, 0) be defined as the distance between tangent planes of a convex body as a function of orientation, Fig. 1. The probability, Pr, of intersecting the body with a randomly oriented and randomly positioned plane, is then equal to the average value of DV (0, $) over all possible orientations. It may be easily shown that for a system of spherical coordinates the probability of finding an orientation between Q and Q + de, $ and $ + d$ is (1/4n) sin $ dB d$, so that This relationship may be applied to each body in an aggregate of convex bodies. In particular, if the bodies in an aggregate are classified according to size and shape, and the ithsuch class is considered, Eq. 111 may be applied to this entire class, the probability of intersecting any body in this class being

Jan 1, 1962

By R. A. Wattenbarger, H. J. Ramey

A systematic study has been made of the application of the real gas pseudo-pressure m(p) to short-time gas well testing. The m(p) function can be used in real gas flow problems to account for the variation of viscosity and z-factor with pressure. A mathematical model was solved numerically to generate solutions of various real gas flow problems. The effects of turbulence, formation damage and wellbore storage were included in the model. The analysis of simulated well tests showed that the interpretation methods normally used for liquid flow are generally accurate when the m(p) is used. For practical rates without turbulence, the solutions are not rate-sensifive, and the flow capacity.. kh and skin effect can be determined accurately from either a buildup or a drawdown test. However, the kh calculated from a drawdown test can be significantly low when turbulence is present. A case was simulated in which this error wa.s 36 percent. Turbulence does not affect the determination of kh from buildup tests. The proper determination of kh from p and pa buildup and drawdown plots is developed by analyzing their relationship to the m(p) method. A simple equation is given that can be used for long-range gas well performance forecasting. This expression is compared with a method pre-sended by Russell et al." Introduction The formation flow capacity and wellbore damage condition can be determined for liquid-producing tests by means of buildup and drawdown tests. These tests make use of short-time pressure transient data rather than stabilized flow tests that are often used for gas well testing. Tracy' presented a method of gas well testing that was based on ideal gas equations and utilized p2 buildup plots. This method was shown to be good for low pressure wells. MatthewsZ suggested plotting p and using an average slope and average gas properties. This method was more successful on high pressure wells. Al-Hussainy, Ramey and Crawfordh howed that variation in gas properties could be simplified by using the real gas pseu do-pressure m(p). Some cases showed that the use of the m(p) function Original manuscript received in Society of Petroleum Engineers office Aug. 8. 1967. Revised manuscript received June 11, 1968. Paper (SPE 1835) was presented at SPE 42nd Annual Fall Meeting held in Houston Tex., Oct. 1-4. 1967, and at SPE 4th Annual Eastern Regional ~eetin$ held in Pittsburgh. Pa., Nov. 2-3. 1967. 0 Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. 'References given at end of paper. provided an accurate method of interpreting buildup and drawdown tests. Because the work of Al-Hussainy et al. included only a few actual cases, there was a need to explore the use of the m(p) method for a greater variety of flow conditions. The occurrence of turbulent flow around the wellbore often is an important factor in gas well testing. Swift and Kiel,' and Carter et a1.' treated turbulence in gas well testing, but did not consider the variation of viscosity and z-factor with pressure. This paper presents the results of an investigation of the application of the m(p) method to buildup and drawdown testing. Vhe investigation included the effects of turbulence, formation damage and wellbore storage. Gas Flow Equations To formulate the mathematical model, many of the assumptions usually used in well testing theory are applied. The system has radial geometry with a closed outer boundary and is composed of a horizontal porous formation that has uniform and isotropic rock properties and uniform thickness. Allowance is made, however, for a radial region of reduced permeability near the wellbore. This region represents formation damage. The geometry of the system is shown in Fig. 1. Darcy's law does not always apply to gas flow. A more general expression is needed for non-Darcy, or "turbulent" REGION OF DAMAGED PERMEABILITY SEALED BOUNDARIES ClRCULAR WELL BORE Fig. 1—Radial flow model. AUGUST, BT7

Jan 1, 1969

The American Petroleum Institute, 250 Park Ave., New York, N. Y. Lacey Walker, Secretary. A complete price list of publications will be sent upon application. The American Petroleum Institute issues a variety of publications; in addition to the Daily Oil Digest ($25 per year) and a weekly Statistical Bulletin ($12.50 per year to nonmembers), a Quarterly is published ($4 per year to nonmembers). Books published by the Institute: American petroleum supply and demand, $3; A series of "Petroleum facts and figures" for each of the years 1928, 1929, 1930 and 1931, $2 for each copy; Function of natural gas in the production of oil, $1; Bibliography of organic sulphur compounds, $4; and "Oil" (Oil Industry Series in one volume), 50 cents per copy. Volumes of the first six annual Meeting Proceedings are out of print, but the Proceedings for the 7th annual meeting in 1926

Jan 1, 1933

SOUTHERN CALIFORNIA LOCAL. SECTION Executive Committee SEELEY W. MUDD, Chairman C. COLCOCK JONES, Vice-Chairman FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER In. order to make the meetings of the, Section more interesting and fruitful, the Executive Committee has formed a sub-committee on programs for. Section meetings, which announces for the coming autumn and winter season, four dinner meetings, at intervals of two months, in which the co-operation of all Section members is urgently. requested. The subjects chosen for discussion at these meetings, with the proposed dates, are as follows: Sept. 28, 1915. Mining Geology of Mojave County, Arizona. Dec. 14, 1915. General Geology and Mining Conditions in Southern California. Feb. 1, 1916. Petroleum, its Geology and Technology. April 4, 1916. General Mining Conditions in. South America. F. J. H.. MERRILL, Secretary.

Jan 10, 1915

By J. A. Reeves

The unit-train for moving mineral raw materials is considered by many railroad men as the most significant contribution toward reducing rail freight costs since the introduction of the diesel locomotive. The idea, which involves assigning railroad equipment to only one haul and keeping the equipment rolling, results in the maximum utilization of equipment. For example, before the unit train was placed in service on coal hauled to one of Mid-Continent Coal and Coke Company's customers, about 900 cars and 9 locomotives were needed to move its coal requirements, compared with 250 cars and 6 locomotives currently used. If unit-train economics are to be achieved, coal companies cannot use railroad cars as small storage bins on wheels to accumulate their coal in train-load shipments, instead, these companies must build large bins which incorporate facilities for the rapid loading of railroad cars in a minimum length of time.

Jan 1, 1970

Sec 1 This Institute is incorporated under the Membership Corporations Law of the State of New York, its corporate name is American Institute of Mining, Metallurgical, and Petroleum Engineers, Incorporated, and its abbreviated title AIME Sec 2 The objects of this Institute, as set forth in its certificate of incorporation, are "To promote the arts and sciences connected with the economic production of the useful minerals and metals, and the welfare of those employed in these industries by all lawful means, to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members the information thus obtained, and to establish and maintain a place for meeting of its members, and a hall for the reading of papers and delivery of addresses, and a library of books relating to subjects cognate to the sciences and arts of mining and metallurgy "

Jan 1, 1960

One of our members, in Colombia, has written the following interesting account of his experience in trying to remit his dues to the Institute. "Last year I was away at the end of the year and on my return I was unable to obtain a draft in Honda until April, I believe. To avoid delay this year I remitted cash, early in January, to a friend in Bogota who I imagined could sell or procure for me various small drafts to cover my annual subscriptions. After many weeks' delay, I was informed that he could not get them for me and was remitting the cash to Honda where they were obtainable. After another long delay, I was informed that no one in Honda would sell drafts or checks for small amounts. Eventually I found a friend who was willing to oblige me in the matter and at once forwarded the amount."

Jan 8, 1919