Search Documents

By W. Joseph Schlitt

The characteristics of successful heap and dump leach operations are first reviewed in a general sense. Then attention is focussed on solution management as the key operating parameter in leaching. The first part of this study includes a detailed conceptual analysis of fluid flow. This identifies the relationships between the flow parameters and the chemical and physical properties of the rock. Then these relationships are extended to practical systems in order to establish optimum application rates and solution distribution methods for heaps and dumps. The study shows that there is a maximum effective application rate, qmax, that can be used without causing solution short circuiting. This rate is a function of the minimum permeability in the heap or dump. The expression for qmax is qmax (gal/ft2/hr)[~]0.9 k (darcies). Here k is the appropriate permeability coefficient. Using this equation, qmax is found to be on the order of 1 gal/ft2/hr (4 cm/hr) for a typical heap or dump leach operation.

Jan 1, 1984

By Leon Y. Sadler

Three new transfer functions relating the time response of the amount of floatable mineral in the under flow to time-dependent changes in the amount of floatable mineral in the feed to the cell are presented. Using experimental stimulus-response data obtained from the flotation of -200+325-mesh glass spheres in a rotor-stator-type cell, the new transfer functions are compared to the only transfer function to be presently found in the literature by nonlinear least-squares fitting in the frequency domain. The new mathematical model based on the amount of available bubble surface area and its rate of introduction is quite promising. The transfer function which allows for a distributed first-order flotation rate constant also gives good results. Simultaneous sodium chloride tracer and glass bead stimulus-response tests show that the mixing conditions in the cell were nearly ideal. It is felt that the new transfer functions presented offer excellent alternatives for use in the design of automatic process control equipment for the continuous mechanical froth flotation cell.

Jan 1, 1974

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain <0.3% Cr203, and chromite is almost always less than 50 mp in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratiform and alpine complexes tend to be either ore grade (>25% chromite) or very low grade (<2% chromite); intermediate rocks are scarce. In most complexes, large tonnages exist only in the <2% chromite rocks and the composition of the chromite in those rocks may be unsuitable for metallurgical use. Some nickel laterite districts contain more than lo8 tons of material with 2.0 to 5.5% Cr203, and hence, chromium could be a byproduct of nickel in some laterite districts. In addition, some chromiferous sand placers may contain tens to hundreds of millions of tons of material between 2 and 5% Cr203

Jan 1, 1983

By Helmer Hedstrom

THE purpose of this paper is to direct attention to the importance and the usefulness of phase measurements in electrical prospecting for ore, a subject about which virtually nothing has been published. The paper describes a new field method for ore prospecting, the "Turam" method, which makes use of phase measurements, and which has been used with great success for five years. Of the principal geophysical prospecting methods, the gravimetric and magnetic methods determine the direction and strength of the static fields of force of the earth. By seismic and electrical methods, fields of force are applied to the block of ground under investigation. By these methods a third parameter can be measured, besides the direction and strength of the field; namely, the time of arrival of the applied field at the different observation points. This time of arrival has been practically the only parameter measured in seismic work, while in electrical pros-pecting it has generally not been considered, the measurements having been limited to determination of direction and strength of the applied field.

Jan 1, 1937

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

By J. W. Axelson

CRUSHING has always been a major operation in the chemical and metallurgical industries, yet little is known about the theory of crushing, and today, the design of crushers is still based almost entirely on empirical knowledge and accumulated practical experience. In view of the increasing national need for the economic working of poorer grades of ores, the lack of a fundamental under- standing of this unit operation hardly presents a satisfactory situation. Basic investigations of crushing have been concerned mainly with three phases of the problem, 1-the mechanism of the fracture process itself, 2- the particle size distribution of the crushed product, and 3-the relationship between the energy input and the amount of new surface produced. Probably adequate information on these phases will be required for a comprehensive understanding of the process of crushing. A bibliography covering these phases will be given as well as a review of the work done in recent years at the University of Minnesota on the relationship between the energy input for crushing and the amount of new surface produced.

Jan 12, 1951

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954

By A. Arrott, G. S. Ansell

A model is proposed to account for the observed strengthening behazlior of ferrous martensites. me model is based upon the inheritance of carbon-rich regions by the martensite which were present in the FERROUS martensite is formed by a nucleation and shear mechanism when austenite is cooled, at a rate which is fast enough to suppress the formation of pearlite, below a critical temperature (Ms ). Although the mechanism of the transformation process appears to be well understood,1,2 the mechanism re- austenite prior to transformation. These carbon-rich regions strengthen the martensite in a manner analogous to the strengthening effect due to a finely dispersed second phase. sponsible for the observed high strengths exhibited by ferrous martensites is uncertain. In this paper, a model is proposed to account for the strengthening of ferrous martensite. MODEL The maximum solubility of carbon in austenite is 1.98 wt pct as compared with a maximum solubility of 0.025 wt pct in ferrite. Prior to transformation, the carbon in the austenite is nonuniformly dis-

Jan 1, 1963

By W. H. W. Husband

Rock salt has been solution mined for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the same method. However, only Kalium Chemicals Ltd. has been successful, possibly because the conditions in Saskatchewan are the most favorable to be found so far for the development of a solution-mining method for potash. In view of the fact that few studies of solution mining of potash have been attempted, only one company has succeeded in using the method, and no information has been released by this company, the application of solution mining of potash ore bodies has to be presented on the basis of available theory, past small-scale studies, and recent patents. A simple mining method is outlined and possible methods of recovering the potash from the brine are discussed. Dissolution data pertaining to solution mining of potash, flowsheets, and material balances are presented. The available information is brought together in a cost analysis to show capital and product costs in terms of 1966 dollars.

Jan 1, 1972

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult&apos;s law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By Jeremias K. Chitunda

Significant cost savings and improved ground stability are two initial indications from the current wet process shotcrete ground support program at the Lakeshore mine. The area of shotcrete for ground stability is not strange to the Lakeshore operation. Since the beginning of the project, various shotcrete techniques have constantly been experimented with, incorporating all the latest technological developments. Over the years, the use of shotcrete has been employed as a primary, temporary, or permanent support, singly or in combination with rockbolts and steel sets. The extent of shotcrete usage compared with steel sets and rockbolts has varied from time to time as dictated by the overall state of the art. In 1972, for example, the ratio of the linear drift footage supported with shotcrete to that supported with steel sets averaged 1.0. In 1973, that ratio was about 3.0. Overall, for the Lakeshore mine, there are about 8000 drift ft of shotcrete, 8000 drift ft of steel sets and timber, 750 drift ft of formed concrete, 21,000 drift ft of rockbolts, and 3700 drift ft of combined type support.

Jan 12, 1974

By Chauncey Berrien

THE Hawkesworth detachable drill steel shank and bit were invented by A. L. Hawkesworth; while he was a mechanical foreman for the Anaconda Copper Mining Co., at Butte, Mont. Mr. Hawkesworth died on June 16, 1925, at the time that his invention was practically a proved success. The first application for patents was made by him in November, 1918, and the bit is now being manufactured under patents issued in 1922 and 1923. The credit, for its development in the early stages belongs to A. L. Hawkesworth, Roy S. Alley, Harry A. Gallwey, E. J. Bowman and various officials of the Anaconda Copper Mining Co. Later improvements, manufacturing problems and the direct usage in the mines were originated and perfected by the mechanical department under C. D. Woodward, E. R. Borcherdt, head of the Rock Drill Equipment Department, Robert E. Kelly of the Mechanical Department, and various operating department heads of the Anaconda Copper Mining Co. The author wishes to acknowledge the assistance of these officials in the preparation of this paper.

Jan 1, 1930

By Persifor Frazer

At a time when all those interested in the iron trade are carefully scanning the horizon for new sources of the raw material, a few words concerning a field, which though not new, has not been hitherto fruitful of statistical information, may be deemed appropriate at this meeting. The district alluded to is the belt of the Middle James River, or in other words, that portion of the ferriferous belts of Virginia lying between Josua Falls and the little settlement of Norwood, in the counties of Amherst and Nelson, and on the left bank of the James River. This region shows unmistakable signs of developing a very considerable market for iron ores and for iron in the future, as well as a tempting appearance of possible productiveness in the former. It, is extremely hazardous to deal in generalizations as to the productiveness or non-productiveness of these measures without a more thorough development than has yet been attained. It is true that they probably constitute an horizon whence comes a part of the marvellous mineral wealth of the northern peninsula of Michigan. But

Jan 1, 1883

[Note.—The paper of Mr. Hoffman on " Practical Results in the Magnetic Concentration of Iron-Ore " (page 602); that of Mr. Langdon on "The Use of Magnetic Concentrates in the Port Henry Blast-Furnaaces" (page 599); and those of Mr. Landis on "The Determination of Iron in the Tails from Magnetic Concentration " (page 609) and "Note on Sampling Iron-Ore" (page 611), were all prepared as contributions to this discussion.] The papers of Mr. Langdon and Mr. Hoffman were presented. W. H. Hoffman, Croton Mines, N. Y.: I will add a few remarks, by way of answer to inquiries for further details. The Croton Mines are particularly well located for cheap mining. The ore-bed is very large, and so lies in relation to the railway tracks of the Harlem and other railroads that a very large proportion of our mining for several years to come can be done above these tracks. The concentrating-mill is now 400 feet from where we are working in the quarry. In blasting we never remove less than 2500 tons at a blast,

Jan 1, 1892

By Charles W. Carter, Alfred H. Bell

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By R. B. Tippin, J. S. Browning

Inasmuch as the higher grade potash deposits are rapidly being depleted, it is important that economic beneficiation techniques be developed for recovering potassium compounds from lower grade sylvite ores and deposits containing clay materials. The Federal Bureau of Mines has conducted research to develop processes for heavy liquid concentration of potash ores, This method of concentration is discussed, and results of tests made on potash ores from New Mexico are presented. The tests demonstrated the technical feasibility of producing near commercial-grade potash concentrates, with a high recovery of the contained sylvite. The concentration of minerals based on their differences in specific gravity dates back to the very beginning of mineral dressing, and the use of heavy liquids in the laboratory to achieve optimum mineral separations has been utilized for many years. With the advent of froth flotation and its success, the incentive to develop new processes has remained relatively dormant. However, flotation refinements in the nonmetallic ores have not progressed as rapidly as in metallic (sulfide) ores because of the complexity of the deposits and the chemical similarities of the minerals.

Jan 1, 1967

By H. L. Barr

THE following report covers the history of the development of the mine, present equipment, methods and costs of mining and milling. In addition, a description of the ore deposit is given with emphasis on the origin of the fractures, mode and types of ore occurrence, and mechanics of granite emplacement. An endeavor has been made to present a complete and accurate statement of the San Mauricio mine, the highest grade gold mine in the Philippine Islands. Credit is gratefully acknowledged to the mine staff for descriptions and details regarding their particular field of work. All analyses were made by Mr. T. A. DeVore, head chemist, San Mauricio Mining Co. Messrs. Edward Wisser, J. E. Fyfe, A. F. Skerl and W. B. Meek, geol-ogists, have contributed geologic information and ideas, for which thanks are extended. The Executive Committee of Marsman and Co., Inc., Managers of the Company, has kindly given permission for publication. Mr. J. B. Stapler, Division Manager, Marsman and Co., has had the courtesy to read the manuscript and to give critical and helpful suggestions.

Jan 1, 1940

By Alfred H. Bell, Charles W. Carter

In 1943, Illinois produced 82,256,000 bbl. of oil, or 5.5 per cent of the total for the United States, and ranked sixth in the nation in oil production. This represents a decline of 23 per cent from 1942, when the total Illinois production was 106,ggo,o~~ bbl. and Illinois ranked fifth. The daily average production for 1943 was approximately 225,000 bbl. Daily averages by months were as follows: Jan......... 238,000 July......... 218,000 Feb......... 240,000 Aug......... 216,000 Mar......... 237,qoo Sept........ 220,ooo Apr......... 230,000 Oct......... 220,000 May....... 221,000 Nov......... 223,000 June......; . 222,000 Dec......... z18,ooo This shows that most of the decline during the year took place between March and May, and that for the last eight months of 1943 production has been essentially steady. This means that there has been enough production from new wells drilled to balance the natural decline of the Older wells. The trends of drilling and production are shown in Fig. I and Table 3.

Jan 1, 1944

By C. W. George, Bruce Chalmers

The authors enumerate the factors which appear, from their observations and practical experience of failure of aircraft components in Great Britain, to be responsible for causing a metal or alloy to fail by stress corrosion. The essential conditions for promoting failure by stress corrosion are: (I) tensile stress at the surface of the component, (either residual or applied), and (2) an attacking medium that may be a solution or a liquid metal. Particular attacking agents are effective only on certain metals. In all instances of stress-corrosion failure experienced, cracking of an intercrystalline form has occurred and examples of such failure in aluminum alloy, steel and copper alloys are described and illustrated. The relation between microstructure and stress corrosion is mentioned and methods of investigating the susceptibility to stress-corrosion failure of metallic materials are described. The precautions to be taken in selecting materials for particular aircraft components and the importance of adequate protection against chemical attack are considered. The authors have given a factual survey of stress corrosion and have made no attempt to advance any scientific explanation of the phenomenon.

Jan 1, 1945