Search Documents

By T. M. Geffen, F. F. Craig

Laboratory model flow tests have been made to simulate field conditions of partial pressure rnaintenance by dispersed gas drive on rocks having sandstone-type porosity. In this production method there is a significant saturation gradient between injection and production wells. A means of calculating relative permeability characteristics. from partial pressure rnaintenance flow tests has been developed. This method takes into account the saturation gradient. These kg/ko characteristics are identical to those for solution and external gas drives. This method of calculation, which has been proved experimentally, has limitations; however, it is valid for cases likely to be encountered in field prediction of partial pressure maintenance performance. The production performance of a hypothetical reservoir has been calculated for several different injection programs, involving both full and partial pressure maintenance. Results indicate that the maxinum oil recovery by these gas injection programs is obtained by full pressure mainte- nance at the original bubble point. Correspondingly lower oil recoveries are obtained by postponing gas injection and/or by reducing the degree of pressure maintenance. INTRODUCTION Dispersed gas injection is an important method of recovering additional oil beyond that obtainable by pressure depletion alone. The injected gas acts as a source of additional energy to displace oil from the rock formation as well as to retard oil shrinkage in the reservoir. In practice, gas injection is usually started after the reservoir pressure has fallen below the original bubble point. For various reasons sufficient gas is generally not injected to completely maintain the pressure in the reservoir. So, injecting gas at a declining reservoir pressure results in a combined external and solution gas drive. These two oil displacement processes are characterized by different gross saturation distributions in the reservoir. The external gas drive, like all frontal drive processes, inherently results in an oil saturation which increases from the injection wells to the producing wells. In the solution gas drive there is essentially a uniform oil saturation throughout the reservoir, provided the field is being depleted uniformly. It has been customary to predict oil recovery performance under partial pressure maintenance by a method which does not take into account the saturation gradient1. It has been shown2 that neglecting the presence of a saturation gradient can cause considerable error. It is the purpose of this paper to develop and present an improved method of predicting partial pressure maintenance performance of reservoirs including, where necessary. the effects of well arrangement. From the laboratory standpoint, this problem involves the measurement of the basic flow behavior (relative permeability characteristics) under partial pressure maintenance conditions. Recent research- as shown that for rocks having sandstone-type porosity, the relative permeability characteristics are identical for solution gas drive and complete pressure maintenance external gas drives. Since both solution and external drives have the same basic flow behavior, it was speculated that partial pressure maintenance, being a combination of the two, would also

Jan 1, 1957

By Morris Muskat

The detailed analogy between flow systems in porous media and the corresponding poten-tiometric model systems is developed under conditions where it may be desirable to take into account variable pay thickness, variable porosity, and permeability, and also the dependence of the fluid density on pressure. It is shown that in such models it is only necessary that the electrolyte thickness be made everywhere proportional to the millidarcy-feet of the formation. In contrast to the iso-vol type model, previously suggested as a basis for the analogy, the porosity does not enter directly in the construction of the model. It is introduced only in translating the electrical voltage gradient measurements into the equivalent fluid travel times. A discussion of this procedure is given. I NTRODUCTION It is now some 50 years since it was pointed out' that on the basis of Darcy's law Laplace's equation must govern the steady state flow of homogeneous fluids through porous media. It is 16 years since the obvious implication of this fact, namely, that such steady state homogeneous flow systems in porous media could be simulated by electrical analogies, was first applied2 to problems of practical interest with respect to oil production. In these initial studies major emphasis was placed on the use of electrolytic models, made of blotting paper, to give a direct and graphic history of the fluid particle motion in regular and infinite well networks. However, it was also noted there that the basic requirement of the model was that it give a potential distribution similar to the pressure distribution in the flow system, and that from the electrical measurement of the potential distribution the fluid particle motion could be graphically or numerically determined. This was demonstrated by application to the five-spot infinite network, for which a conducting metallic sheet was used to establish the equipotential contours. As anticipated, the fluid particle motion computed from these contours agreed well with that given directly by the blotting paper model. For irregular well distributions it was found more convenient to use electrolytic bath analogs rather than metallic sheets. Several investigations,3'4 as applied specifically to cycling well patterns, have been reported with these models, which have become known as "potentiometric models." However, the extremely laborious nature of both the electrical measurements by direct probing and the associated interprctive computations retarded the widespread use of these procedures. The electrical measurements can be accelerated by using a four-probe electrodc,5,6 which provides a means for simultaneously determining the streamline paths along which the fluid particles must move and the voltage gradients along these paths which are proportional to the fluid velocitics. With the increasing frequency of discovery of condensate pools, as drilling depths are becoming greater, the applicability of the potentiometric model to production problems, and especially to the study of well patterns for cycling, has been given a fresh impetus. Although the formal theory for determining the motion of fluid particles in porous

Jan 1, 1949

By M. H. Cullender

The performance characteristics 01 gas wells producing from formations which fail to stabilize within a relatively short period of time are obscured by the interrelation of the coefficient (C) and the slope "n" of the conventional back-pressure curve q = C(P2 f- p2s)n An empirical method is presented whereby the characteristic or true slope (11) of the back-pressure curve may be determined for a particular gas well. For those gas wells which do not stabilize within a relatively short period of time, the coefficient (C) is considered as a variable with respect to time and as a constant only with respect to a specific time. Thus, the back-presrure performance of such a well is presented as a series of parallel curve5, each curve representing the performance of the well at the end of a given time interval. Through use of the method presented, a simple presture gradient is developed and maintained within the drainage area around a producing gas well during the test period in order that the variation of the coefficient (C) with respect to time does not obscure the true value of the lope. INTRODUCTION The back-pressure method of testing gas wells as set forth by Schellhardt and Rawlins1 is dependent upon the requirement that a series of flow rates and corresponding pressure data be obtained under stabilized conditions. These data arc then plotted on logarithmic coordinates of flow rate (Q) vs difference in squared pressures (P2f — P2s) in order to determine the constants (C) and (n) for Equation 1. With respect to this method of presenting the performance characteristics of a gas well, it should be pointed out that although Equation 1 is an empirical relationship, the form of the equation was justified to a considerable extent by an independent development by Muskat and Botset.2 This development was theoretical in nature; however, certain assumptions with respect to the type of flow existing (viscous vs non-viscous) were madc which may or may not be correct. As the use of the method presented by Schellhardt and Rawlins spread through the industry, it became evident that the method of testing was applicable for those wells which approached stabilized prbducing conditions within a relatively short period of time. Performance characteristics could not be determined by this method, however, for wells which approached stabilized protlucing conditions slowly over a considerable period of time. This characteristic of "slow stabilization" has generally been associated with gas wells producing frorn reservoirs of low permeability. As the demand for natural gas continued to grow through the years, a great number of wells were completed in reservoirs of low permeability which exhibited "slow stabiliz:~tion" characteristics. Consequently, the problem of determining the true performancc characteristics of these wells became more apparent. It is with this problem in mind that the isochronal performance method of determining the flow characteristics of gas wells is presented.

Jan 1, 1956

By Jr. D. C. Williams, D. V. Carter

The four new oil-field discoveries made in the East and East Central Texas districts during 1941 were the East Long Lake field, Anderson County; Pickering field, Shelby County; Pleasant Grove field, Rusk County, and Tri-Cities field, Henderson County. The discovery of oil production in the Pettit lime of the Lower Glen Rose was made in the Groesbeck (Barron) field in Limestone County and the Willow Springs field in Gregg County. Important extensions were made to the Pittsburg field, in Camp County, the Chapel Hill field, in Smith County, and the Hawkins field, in Wood County. The Hawkins field was extended sufficiently to more than double the number of proved surface acres. As usual the East Texas field led the district in the number of completions for the year. The second most active field during the year was the Hawkins field, with 250 new wells completed. The third most active was the Long Lake field, in which 50 wells were completed. Approximately 964 wells were completed in the district during 1941. Production and Probation The district is credited with having produced 163,566,695 bbl. of oil and distillate during the year. This represents a decrease of 4 per cent from the 170,424,685 bbl. of oil and distillate produced during the preceding year. The production of 130,378,620 bbl. of oil and distillate from the East Texas field represents 79.7 per cent of the total production of the district; that is, 6.3 per cent less than the production for the year 1940, The district had an estimated basic daily allowable of 614,982 bbl. of oil on Dec. 31. Approximately 33 per cent of the state's annual production was produced in the district, compared with 34.9 per cent for 1940. Since the majority of the fields in this district are subject to proration, any change in the annual production is attributable largely to changes in proration schedules and number of shutdown days. Fields subject to shutdown days were closed in for 113 days during the year, with the exception of the East Texas field, which was shut down 111 days. An order was promulgated by the Oil and Gas Division of the Texas Railroad Commission for encouraging the disposal of salt water and reservoir-pressure maintenance in the East Texas field. Discoveries Tex Harvey Oil Company'sNo. I S. E. J. Cartmel was completed as the discovery well for the East Long Lake field, Anderson County. Production was found in the Woodbine sand, the horizon from which the Long Lake field produces. The Pickering field, Shelby County, secures its production from the Nacatoch sand, found at an approximate depth of 1510 ft., in A. E. McKiernan's No. I, Pickering Lumbering Co. This field is in an area near the state line in which a number of relatively unimportant and

Jan 1, 1942

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By Fred W. Stiefel

This paper covers the operation and maintenance of Diesel locomotives underground on a portion of the Delaware River Aqueduct. † This part of the tunnel is 15 miles long, with shafts 14 ft. in diameter spaced about 5 miles apart. These shafts (2, 2a and 3) are 825 ft., 1551 and 840 ft. deep, respectively. The grade of the tunnel is almost level, except for the 12,100 ft. north of shaft 2, which has a grade of 2.31 per cent. The tunnel is circular, 17 to 19 ft. in diameter. It lies at a depth of 400 ft. below sea level, with a maximum overburden of 2400 feet. The tunnel driving was carried on in six headings, using 15 storage-battery locomotives, each of 13 gross tons and having a maximum speed of 8 miles per hour. The longest haul was 3 miles, which proved to be the maximum distance for which storage-battery locomotives could be employed economically for the amount of material to be moved. One locomotive was used for switching cars at each heading, one for switching cars at the bottom of each shaft and one on the main-line haul from the heading to the shaft. The maximum amount of material hoisted in one shaft from two headings when 104 ft. of tunnel was driven in 24 hr. was 1000 cu. yd., or about 2000 tons of rock in place. The total quantity excavated was 750,000 cu. yd. (1,500,000 tons of rock). The tunnel-lining operations using concrete presented a problem of hading a maximum distance of 5 miles in the tunnel. The concrete-placing equipment had a capacity of about 2000 CU. yd., or 4000 tons in 24 hours. Experience had shown that storage-battery equipment could not handle this quantity of material within the time required at the distance of 5 miles. Trolley-locomotive haulage was considered dangerous and expensive, and would cause interference because transmission equipment would be required. Therefore the performance of Diesel locomotives of 160 hp., with a speed of 18 miles per hour, in comparison with that of other types of locomotives, was studied. Choice of Locomotives In deciding upon the type of locomotive to be used for the 5-mile haul, four alternatives were considered, as follows: I. To purchase additional storage-battery locomotives with the necessary batteries over the 6 locomotives and 12 batteries available. 2. To convert the existing battery locomotives to the trolley type. 3. To purchase new trolley locomotives. 4. To purchase Diesel locomotives. Proposition No. i The 90-hp. storage-battery locomotives the (each weighing about 12 tons), when hauling a load of 64 tons, with a drawbar pull of about 1900 lb. on a level track, developed a speed of 8 miles per hour and could make five round trips in 8 hr. with a

Jan 1, 1943

By W. I. Duvall, D. E. Stephenson

A theoretical solution is given for the energy that is radiated outward when either a cylindrical or spherical cavity located underground in a uniform stress field is suddenly created or enlarged. The method of derivation shows that the stress field in the solid rock surrounding the opening does work on the rock because of elastic displacements that result when the size of the cavity is increased. The amount of this work is sufficient to account for both the increase in the strain energy in the rock surrounding the opening and the seismic energy that radiates outward. Thus, the source of the radiant seismic energy is mainly the gravitational potential energy and not the strain energy stored in the rock. The amount of the radiant seismic energy is directly proportional to the volume of the rock removed from the opening or relieved of stress. Seismic energies from rockbursts are compared with earthquake energies. Also, the amount of gravitational potential energy released by underground explosions is calculated and found to be small compared to the seismic energy generated by the detonation of the explosive. A review of the early literature on rockbursts shows that a number of investigators calculated the amount of energy released by rockbursts. 1-5 However, none of these papers give the formula used to make these calculations or a reference to the derivation of any formulas. The general impression that one obtains from these early papers is that the main source of the seismic energy released by rock-burst is the strain energy stored in the rock before it is fractured. However, a few of the early papers appear to have considered the solid rock at a distance from the mine opening as a possible source of the seismic energy. Recently Black and starfield7 gave a theoretical solution for the strain energy in a stressed plate with and without a circular hole. Also, Press and Archambeau8 gave the theoretical solution for the seismic energy released when a spherical cavity is created in rock subjected to a three-dimensional stress field. Both of the above theoretical papers start with the condition of no opening and calculate the strain energy before and after the opening is suddenly formed. Neither of these papers appear to have calculated the work done by the applied stress field as the cavity is enlarged. The rockburst problem associated with deep mining is concerned with the failure of the solid rock surrounding an underground opening. Therefore, it seems appropriate to consider theoretically the problem of suddenly enlarging the size of an existing opening. The purpose of this paper is to present the theoretical solution for the energy that is available for release as seismic energy when an underground circular tunnel or spherical cavity is suddenly enlarged in diameter. To keep the mathematics as simple as possible, a uniform radial applied stress field is assumed and the rock is assumed to be isotropic, homogeneous and perfectly elastic.

Jan 1, 1965

By H. M. Bannerman, E. N. Cameron

INTRODUCTION DURING the years 1942-1944, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailed studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times, for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larrabee, A. H. McNair, J. J. Page, V. E. Shainin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. ANALYSIS OF WARTIME OPERATIONS In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 1/3 to 2/3 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the transition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1946

By H. M. Bannerman, E. N. Cameron

During the years 1942-1934, about 125 New England deposits were mined for sheet and punch mica, and many others were briefly prospected. During this period the Geological Survey, United States Department of the Interior, carried on detailcd studies of the deposits and the pegmatite bodies that contain them. The primary purpose of the studies was to provide geological information that would contribute toward efficient mine development and operation. The studies were aimed directly at practical production problems. Detailed maps showing the structure of the deposits were prepared, and geological findings were closely correlated with data on specific yields and costs of mining and processing. The result is information that permits a reasonably accurate appraisal of the mica deposits of New England and the mining industry that they support. At a time when the future of the industry is in doubt, it seems desirable to submit this appraisal for consideration. Domestic mica deposits supply only a small fraction of the country's needs in normal times? for only the richest domestic deposits can compete with the low-cost mines of India and Brazil. However, the possibility that this country may be cut off from its supplies in time of war gives domestic deposits an importance much greater than their peacetime production would imply. New England supplied about 22 per cent of domestic output in 1943 and 1944, the peak years of wartime production. Its actual contribution to the war effort was greater, for the proportion of sheet mica of high quality in the New England product is higher than the average for domestic mica. The data analyzed below were collected for the Geological Survey by D. M. Larra-bee, A. H. McNair, J. J. Page, V. E. Shai-nin, G. W. Stewart, and the co-authors of this paper. The cooperation of officials of Colonial Mica Corporation and of mine operators and owners in furnishing information is gratefully acknowledged. D. M. Larrabee, A. H. McNair, and V. E. Shainin have made various suggestions based on critical reading of the manuscript. Analysis oF Warrtime Operations In considering the data presented in this report, it must be remembered that the scale of mica operations is very small compared with that of many other mining industries. The typical New England mica mine of 1943 and 1944 was worked by a crew of five or six men. Equipment was varied but on the whole extremely simple. The first stage of operation at a deposit was normally opencut mining. Drilling was done mostly with jackhammers powered by portable compressors driven by gasoline engines. Muck was shoveled by hand into buckets with a capacity of 45 to 35 ton and commonly hoisted by derrick to a dump adjacent to the cut. As operations were carried to greater depth, and the tram sition to underground mining was made, these methods were modified to a degree depending largely on the attitude of the deposit mined. At steeply dipping deposits,

Jan 1, 1948

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By J. S. McNeil, J. U. Messenger

In the drilling of oil wells the control and prevention of lost circulation of the drilling- fluid is a oroblem which is frequently encountered; in many cases existing materials and methods for alleviating this condition have not been adequate. For severe cases of lost circulation in which the simpler methods, such as application of various bridging materials to the mud system, have proven unsatisfactory. a new material and method for applying to the loss zones have been developed which appear to he superior to existing techniques in many respects. The material, called a clay cement, is capable of being handled as a drilling fluid after initial mixing of the solitl ingredients with water and may be pumped down the drill pipe and squeezed into loss zones. After a short period, the material develops a very high gel strength which seals off the zone against further losses of the drilling fluid. In field tests, the process has been demonstrated to be a very effective method for combatting lost circulation. INTRODUCTION Methods of treating lost circulation in rotary-drilled wells by the addition of special materials to drilling fluids have long been in the process of development and are continuing to improve.' However, the annual drilling costs which can be traced directly to lost circulation difficulties still run into the millions of dollars. The loss of mud materials into highly permeable zones may range up to $50,000 per well in some areas. In addition to mud costs, excessive requirements of casing, cement; rig time, and the attendant blowout hazards further emphasize the importance of the need for improved methods of combatting lost circulation. The shortcomings of presently-used materials and methods have led to the development of a new lost returns material in the form of a time-setting clay cement. In field tests this material has proven very successful in plugging off loss zones. which other more conventional materials had failed to do. REVIEW OF PRESENT CORRECTIVE MEASURES The proper control of such operating factors as pump pressure, clearance between pipe and hole, and speed of running pipe in a holez is of primary importance in preventing and minimizing lost circulation problems. These factors, however, concern matters of drilling technique and do not directly involve lost circulation materials. Aside from setting casing past loss zones, three principal methods are generally employed for the purpose of avoiding or combatting lost circulation: (1) adjustment in properties (principally density) of the drilling fluid, (2) addition of fibrous, flaky, granular or other types of bridging materials to the mud system, and (3) the application of cements to the loss zones. The latter method is usually employed only after the first two have proven unsuccessful. In Table I are listed some advantages and disadvantages of the common corrective measures. Frequently, a combination of bridging material and cementing material is used." This combination is based on the premise that a bridge will

Jan 1, 1952

By Raymond Mancha

A TEST of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fan shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define dearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving loser agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the Pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DEFINITION OF FAN PRESSURES The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total pressure is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. Table i.—Results of Timber Survey in 1925 before Treated Timber Was Introduced Length of tunnels and gangways ft..... 522,987a Length of tunnels and gangways timbered, ft.................................. 224.880 Number of steel mine sets in use......... 2,412 Number of timber sets in use............ 63,834 Number of timber sets with evidence of rot 50: 419 Number of timber sets with evidence of squeeze..... ...................... I3,415 Percentage of all timber sets showing evidence of failure: BY wet rot........................ 6.0 By dry rot........................ 73.0 By squeeze....................... : Average life of wood set in Panther Valley, years............................... 5.3 • 99.05 miles. In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. Quantities and Treatments OF Treated Timber Purchased In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required On their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By Paul L. Burkhart

THOUGH at an earlier period brief studies had been made by the Lehigh Navigation Coal Company Inc., it was not until 1924 that J. B. Warriner, then general manager, called for a comprehensive study of timber treatment, treating solutions, and related operations. Because of the impossibility of procuring accurate costs and other pertinent treating data, the American Wood Preserving Co. agreed to treat a car of mine timber at the Port Reading plant of the Reading Railroad. Fig. I shows the treating data collected at the treating plant on this timber, which was installed in two of the Lehigh mines in 1925. Table i.—Results of Timber Survey in 1925 before Treated Timber Was Introduced Length of tunnels and gangways ft..... 522,987a Length of tunnels and gangways timbered, ft.................................. 224.880 Number of steel mine sets in use......... 2,412 Number of timber sets in use............ 63,834 Number of timber sets with evidence of rot 50: 419 Number of timber sets with evidence of squeeze..... ...................... I3,415 Percentage of all timber sets showing evidence of failure: BY wet rot........................ 6.0 By dry rot........................ 73.0 By squeeze....................... : Average life of wood set in Panther Valley, years............................... 5.3 • 99.05 miles. In the latter part of 1925, a survey of the tunnels and gangways of the company's Panther Valley mines was made to determine the proportion of gangways or tunnels timbered, cause of timber failures, approximate life of the average wood set and the approximate percentage of treated timber that it would be profitable for the company to use. Results of this survey appear in Table I. Because of the high percentage of timber that gave evidence of failure by rot, as noted in Table I, and a further study of the life of the sections where timbering was necessary, it was deemed advisable to fill 25 per cent of the yearly gangway timber requirement with treated timber. Quantities and Treatments OF Treated Timber Purchased In the early days of the program, none of the large treating companies would accept orders for small quantities of treated timber and the company was compelled to state the quantity of timber it would require at each operation in each month of the year. Table 2 is an example of the tabulation given to the various treating companies to assist them in making a yearly bid on the minimum quantity of timber required by the company during the year 1931. A bill of timber was calculated for each car, the weight of which would be between the minimum and maximum weight permitted for railroad-car loading. The treating company was paid for timber upon delivery at the operation specified. As extra cars of timber were required, they were ordered from the treating company, and payment was required On their receipt, on the basis of the piece or tonnage

Jan 1, 1942

By G. E. McElroy

THOUGH air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena-some mine-gas explosions, for instance-that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experiments in which the author has participated: experiments on fan-pipe discharge, on the dilution of gases discharged from a stack and on the ventilation of a ship's hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.1 The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. JET CHARACTERISTICS The jets commonly encountered are those in which the air is in turbulent-as opposed to laminar, or streamline-motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases. In the case of entrainment in the free

Jan 1, 1945

By Leendert de Witte

A review is given of the principles on which recently proposed methods of electric log interpretation in shaly sands are based and of the evidence brought up in support of the theoretical derivations. It is. pointed out that the qualitative techniques suggested to date have a tendency to be too pessimistic in the prediction of the presence of commercial hydrocarbon accumulations. In the quantitative treatment, a new concept is introduced, namely that of strongly reduced activity of the double layer counter ions which are present near the negatively charged rock surfaces. This lemmu when applied to the calculation of the equilibrium concentratiotls of interstitial waters yields a set of very simple relations. The resulting expressions for electrochemical potentials across rock samples appear in satisfactory agreement with laboratory experiments. The formulae obtained for the electrical conductivity of shaly formatioris are of the same form as those arrived at empirirally by previous workers. Combination of the expres.riorls for potentia1s and conductivities gives a direct proof of the Tixier relation which states that for shaly water sands the product of apparent formation water resistivity and apparent formation factor equals the resistivity of the sand 100 per cent .saturated with formalion water and which was verified by the work of Wyllie and Perkins and their co-workers. The relations for the resistivities and spontaneous porer11inI.s have been extended to the case of hydrocarbon hearing shaly formations, thus laying a formal basis for the quantitative interpretation of electric logs in shaly oil sands. INTRODUCTION The presence of disseminated clays in porous rocks saturated with electrolytic solutions has a strong influence on the transference of ions taking place under electrical or chemical potential gradients. Both the electrochemical emf's in evidence on the SP curves of electric logs and the electrical conductivity measured on resistivity logs arc directly dependent on the ionic transference in the interstitial waters of the formations traversed by boreholes. A large number of researches have been carried out on the nature and magnitude of the effects of clays on ionic transference. The most recent of these have been described in papers by McCardell and Winsauer,1 2 Wyllie and Southwick,3 poupon, Loy, and Tixier,4 and by Perkins et al.5 Most of these authors consider the effects of the clays as due to the fixed negative charges on the clay lattice. These charges cause the formation of diffuse surface layers with a high concentration of positive ions. The internal solution of the shaly reservoir rock has therefore a different ionic composition and concentration than the electrolyte with which it is in equilibrium (connate water produced from the formation or mud filtrate by which the formation is invaded). To calculate the equilibrium concentration of the internal solution, use is made of the Donnan6 relation, which states that the mean ionic activities of the internal solution and of the external electrolyte must be equal. From this and the

Jan 1, 1956

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By James M. Stapleton

IT has long been recognized by blast- furnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (I) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/C02 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/C02 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. APPARATUS The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By James M. Stapleton

It has long been recognized by blastfurnace men that correct top distribution of materials is very important in efficient and economical furnace operation. Thousands of experiments on top design, filling, sizing, and other operations have been carried out to improving furnace performance by securing uniform distribution. Many of these experiments have worked out satisfactorily and have been passed along to the industry. Many of them have been discarded and forgotten. It has been the custom to judge the results of such experimentation by the results shown in improved or lowered furnace efficiency. While the effect on furnace practice will have to continue to be the final criterion of experimental changes, it has always been a desire of blast-furnace men to ascertain the reason for failure or success. Efficiency in the blast furnace approaching the maximum can be measured in several ways: (1) by actual operating results as revealed in the coke rate and tonnage figures, and (2), in the degree to which the top gas approaches the limiting ratio of CO/CO2 for the reduction of iron oxide by CO gas. This ratio is shown in the equilibrium curve in Fig. I for the system Fe-O-C and CO2-CO-C. The closer the top gases approach this limiting ratio (set at 1.08 by Martin1 because of the effect of limestone calcination) the more efficiently we may expect a furnace to operate. The fact that low CO/CO2 ratios parallel eficient operating performance caused us to investigate the cause of good or poor distribution and the effect of filling and other changes on furnace operation. Heretofore it has been possible to take a sample of furnace gas (usually from the dust catcher) and from it determine how closely the reducing gases were to the ideal or limiting value as set by the equilibrium diagram. However, to find just where in the top area the distribution was distorted and the top-gas CO/CO2 ratios were distant from equilibrium values has been a difficult and expensive investigational procedure. In an effort to overcome this difficulty, apparatus was designed to take gas samples and temperatures across the top radius of the furnace. It was hoped that with the aid of this apparatus traverse sampling of the ascending gases could be simplified, and the cost of sampling substantially lowered. Routine experimenting could then be maintained and results checked with furnace operation. It must be emphasized that a traverse sampling is necessary for a true picture, as single samples at any one point are unreliable. This statement can be verified by an examination of Tables 3 to 6, showing results obtained at our furnaces in a large number of tests. Apparatus The design of the equipment for taking the samples was governed by the need for providing a simple, routine test that could be performed fairly quickly without adversely affecting normal furnace operation.

Jan 1, 1943