Search Documents

By Richard Franchot

From an efficiency viewpoint, the greatest loss of energy to the blast furnace is in its failure to convert more than about a third of the coke carbon from carbon monoxide to carbon dioxide. This result has usually been ascribed to a necessity of a 2:1 excess of CO in order to reduce iron. It has, however, been proved that iron is completely reduced by equal volumes of carbon monoxide and carbon dioxide. Hence there is room for the hypothesis that vaporization, as cyanid, of accumulated alkalis is a serious primary factor limiting the ratio of ore to coke. Observed cyanid vapor concentrations and those measured by the variations of the nitrogen-oxygen ratio in the hearth gases form the basis for a quantitative explanation of the furnace action. As EVERYBODY knows, the blast furnace is a gas producer. As to the reason for this, people are not so well agreed. The significance of the fact is obvious, for the extent to which the fuel leaves the furnace as combustible gas measures poor economy in iron smelting; while good efficiency in this respect means poor gas. The furnace thus works at cross purposes. The present trend of the steel industry is toward. a primary use of the blast furnace as a gas producer with pig iron as a byproduct. Needless to say, this trend is away from improvement in iron making. The production of more and better iron in a given furnace consuming a given amount of coke would seem, at least, to involve a decrease in the relative proportion of the combustible gas. The possibility at the same time, however, of making more and better gas need not necessarily be excluded. (The more the furnace acts as gas producer, the bigger is the sulfur problem.) Whatever the object, it would seem desirable to have a, clear, comprehensive, mathematically exact estimate of why and how the blast furnace functions, to the large degree that it now does, as a gas producer. The literature does not give a definite answer to the question. That for which explanation is sought is the fact that only a minor part, usually not more than a third, of the coke carbon burned is oxidized to carbon dioxide; that the development in the furnace of the fuel energy is thus limited usually to little more than 50 per cent.; that it requires about twice as much fuel coke to make a ton of iron as is indicated by the rela-

Jan 7, 1925

By C. G. Dunn

Nuclei that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,&apos; that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclasses† of the 36 third-order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of deformation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a (110) plane in a <100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is not particularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1947

By Gustav S. Preller, A. M. Gaudin

For the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2-4 and has now received confirmation as to accuracy by an entirely independent method.&apos; This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8?2 or 16.2?2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8?2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura&apos;s results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2?2., with extreme values at 13.7 and 16.9?2. The average of 21 determinations made in connection with this study7 gave a parking area of 14.3 ± 0.27?². In view of this result and of the Harkins and Jura

Jan 1, 1947

By C. G. Dunn

Nuclei that are formed during the recrystallization of a grain following plastic deformation generally have orientations that differ from the original. This aspect of recrystallization may be described in terms of orientation changes. It was shown previously, in an investigation on recrystallization in silicon ferrite,&apos; that the observed orientation changes were highly improbable on a chance basis, and that some mechanism must be involved. Analysis showed that the data could be satisfactorily classified into the smaller of two subclasses† of the 36 third-order twin transformations. No attempt was made at that time to classify the data within the special class of 12 third-order twin transformations, although results did indicate a greater probability for some of them to occur. A classification of this type would be more valuable, of course, with more data on orientation changes per old deformed grain. The present work fulfills this condition to some degree and also extends the scope of the investigation to include the effects of original orientation and the amount of plastic deformation. The effect of original orientation is of considerable interest because of the known effects of orientation on plastic deformation, particularly with regard to degree of fragmentation and the formation of deformation bands, and because the orientations produced by deformation should influence the orientations obtained through recrystallization. Barrett and Levenson2 reported that single crystals of iron deformed in the range 82 to 97 per cent could be put into three general classes; namely, crystals in class I maintained a reasonably sharp single orientation, those in class 2 transformed into two distinct orientations, and those in class 3 changed into a large number of major and minor orientations. Something similar would be expected for silicon ferrite crystals, and verification of this for a few cases of types class I and class 2 deformation has been reported elsewhere3 for single crystals of silicon ferrite cold-rolled in the range 10 to 20 per cent. As an example of class 2 deformation, it was shown that a crystal of silicon ferrite cold-rolled in a (110) plane in a <100> direction developed two layers, or deformation bands differing in orientation. When this happens it is possible to etch away one band and leave a single structure for use in studying the orientation changes that occur during recrystallization. when preferred crystal orientations are obtained in recrystallization, it is not particularly necessary to evaluate groups of common orientation, as was done previously (ref. I, Table 6); but an

Jan 1, 1947

By Harold W. Scott

Geological Engineering is now a recognized curriculum in most of the mining schools in United States. Graduates of these schools are scattered over the face of the earth, participating in exploration and mining enterprises of diverse character. They are engaged in the mapping of new mineral deposits, in the extension of old deposits, the estimation of reserves, microscopic analysis, and in the direction of exploitation and conservation of man&apos;s natural resources. The training of men qualified to carry out these technical phases of modern industry has fallen essentially to the mining schools. For the most part they have met the demand for technically trained men in the mineral industries. Schools Offering Geological Engineering Degree The mining schools have passed through the early stages of their development and at the present offer varied curricula covering the fields of geological engineering, mining engineering, and metallurgical engineering. Usually a B.S. degree is offered in any of these three fields. However, .there has been some tendency of recent date on the part of the Engineers Council for Professional Development to question the validity of a B.S. degree in Geological Engineering. The of this paper is to examine the curricula as offered in the mining schools, to evaluate their engineering content, and to propose minimum requirements for the degree of Geological Engineering in the mining industry. The curricula of eight institutions that offer the degree of B.S. in Geological Engineering or Mining Geology have been studied (Table 1). All except one of these schools are in or near mining districts and occur west of the Mississippi River. They are all state-supported institutions that have come into existence because of the state&apos;s need for technically trained men. A graduate from .a mining school is called upon to perform many duties of a technical nature. His initial task may be to make a geological map of a mine or the surface above, but before the map is finished he may be asked to take over the responsibility of getting the ore "on top." And finally, he might find it essential to know how to mill the ore. Certainly this requires technically trained men and the mining schools are essentially the organizations to do the job. The departments of geology in these schools are training geological engineers. Field Of Geology If we were to accept the opinions of some writers, we would be forced to conclude that all geology departments offer only a "dilettante" variety of subjects.

Jan 1, 1944

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy&apos;s law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy&apos;s law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

IN 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group -SO4- or _S03- are excellent collectors for cassiterite and promise to be selective.1 The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000gram Denver cell. EXPERIMENTAL METHODS Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously described.5-10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these tests determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver Submachines.--Melbourne tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By Brison Robertson, W. P. Fishel

THE carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. One important phase of this subject is the distribution of carbon between the various elements present. The distribution of carbon between iron and other elements evidently will depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying elements and iron and between the elements themselves. In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds. In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present in a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. EXPERIMENTAL PROCEDURE Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a vacuum, in an induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would complicate the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were cooled in the furnace under a vacuum and were then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (I :4) sulphuric acid, and the complete solubility of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe, was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others 1,2 have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represents the titanium that was united with carbon. The filtrate from the carbide residue contains the portion of the titanium that wasin solid solution in the ferrite. Titanium

Jan 1, 1944

By Gustav S. Preller, A. M. Gaudin

For the past 20 years it has been generally accepted that the flotation process is made possible as a result of the action of certain chemical substances on the surface of the mineral particles. In fact, it has been suspected, but never demonstrated, that this action produces on the mineral particles a layer of chemosorbed ions that is of the order of magnitude of a monolayer; that is, of a layer one ion deep. It is the purpose of this paper to present certain initial results on the relationship of mineral surface area and collecting-agent requirements. Up to about eight years ago, all considerations involving the surface area of finely divided solids were limited by the fact that there was not in existence any general method for determining the extent of such surfaces, especially on mixed materials. However, the method invented by Brunauer, Emmett and Teller1 has changed the situation by providing a general procedure (BET method). This procedure has already been applied to mineral dressing problems2-4 and has now received confirmation as to accuracy by an entirely independent method.&apos; This confirmatory or "absolute" method uses a very tedious calorimetric procedure and is not suitable for routine determinations; but still another method6 now is available to relate the results obtained by the BET method to those obtained calorimetrically. This Harkins-Jura method has the advantage that it does not require an assumption concerning the parking area per molecule of adsorbate (nitrogen). In the original work by Brunauer, Emmett and Teller the parking area per nitrogen molecule was calculated to be either 13.8?2 or 16.2?2. according as the nitrogen was assumed to be closely packed as in crystalline nitrogen or loosely packed as in liquid nitrogen. The initial experimental work from this laboratory2 supported the 13.8?2. figure; that work was done on glass spheres of measurable geometric area and it was based on the assumption that the glass spheres were truly smooth; any deviation from this assumption would, of course, have made the calculated parking area higher. Harkins and Jura&apos;s results suggest that the parking area is not the same for all substrata; furthermore, the average of the 87 measurements cited indicates a "preferred" parking area for the nitrogen molecule of about 15.2?2., with extreme values at 13.7 and 16.9?2. The average of 21 determinations made in connection with this study7 gave a parking area of 14.3 ± 0.27?². In view of this result and of the Harkins and Jura

Jan 1, 1947

By L. Wahl, M. Allard, B. Trentini

REMOVAL of sulfur in steelmaking is presently a problem of utmost importance as requirements on final sulfur contents in finished steels become increasingly strict. This is in spite of often increased sulfur contents in the fuels used during the different stages of steel processing. According to local conditions or current economic factors, sulfur can be removed during one or more of the processing operations; for instance, in a blast furnace operated under high temperatures and with a high slag basicity ratio and also by means of high inputs of manganese into the burden. These methods of proceeding are, however, expensive and in contradiction with the acid practice which is gradually being developed owing to the fact that it allows coke and lime savings and usually permits an increase of productivity. In the melting-shop, desulfurization can proceed in the open-hearth or electric furnace with one or several very basic slags, or with special prefused slags (Perrin process) mixed with steels poured from the open-hearth, electric furnace, or converter. Liquid pig iron has also been treated separately before being used in the melting shop, in order to reduce high sulfur contents. This external desul-furization has been developed in Europe for the basic Bessemer Thomas process, which is again in favor owing to the great flexibility of such installations and to the fact that the steel produced is not polluted by impurities coming from the scrap. Since the basic Bessemer process, as usually practiced, has a low desulfurizing power, external desulfurization is generally carried out in ladles by means of alkalies such as soda ash. This method, which has the advantage of being simple and costing little, has only a medium desulfurizing power, which implies the necessity for repeating the operation several times when a substantial amount of sulfur has to be removed or when very low sulfur contents are desired. Thermal losses are high and there is a considerable decrease in output. Moreover, the resulting fluid and corrosive slag, which is extremely difficult to eliminate, attacks the refractory linings of the mixers and steel furnaces. Therefore, it seems necessary to devise a simple method for external desulfurization which would not only remove substantial quantities of sulfur from the hot metal coming from an acid blast furnace, but which would also bring the sulfur contents down to the low level required in the making of high quality steel and iron. Principle of the Process In this paper a new method will be described for desulfurizing hot metal. It has been perfected by

Jan 1, 1958

By Brison Robertson, W. P. Fishel

The carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. one important phase of this subject is the distribution of carbon between the various elements present. The distribution of car. bon between iron and other elements evidently sill depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying and iron and between the elements themselves, In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds, In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present ill a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a Vacuum, in an Induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would the the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were the in the furnace under a vacuum and "&apos;ere then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (1:4) sulphuric acid, and the complete solubility Of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe. was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represerifs the titanium that was united with carbon The filtrate from the carbide residue contains the portion Of the titanium that was in solid solution in the ferrite. Titanium

Jan 1, 1945

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young&apos;s modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young&apos;s modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-&apos; (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young&apos;s modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C&apos;. Young&apos;s modulus of polycrystalline samples with strong [110] textures and Young&apos;s modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young&apos;s modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young&apos;s modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

By Charles T. Baroch, Charles J. Baroch

In 20 years of commercial development, nuclear reactors have demonstrated that they are a safe, dependable, and economical source of power. Operating experience with commercial power reactors has firmly established nuclear power as a practicable source of energy. For both boiling-water (BWR) and pressurized-water (PWR) reactors, performances to date have generally met design predictions. Furthermore, it has become possible to analyze and understand the nuclear, chemical, and physical behavior of this class of reactors. The United Kingdom has had similar success with gas-cooled reactors. The Experimental Boiling Water Reactor (EBWR), the first United States experimental power reactor, began operation in 1956. It proved to be capable of supplying 4500 kw (kilowatts) of power. This reactor was followed in 1957 by the Pressurized Water Reactor at Shippingport, Pa. It was the nation&apos;s first full-scale central-station nuclear power plant and the first in the world designed exclusively for the production of civilian electric power. The Shippingport reactor was originally designed to produce 60 megawatts (MW) of electricity, and it was increased to 100 MW in 1964. In 12 years of operation, this reactor generated over 4.5-million MW-hr of electricity in spite of many shutdowns for experimental alterations. By 1969, a total of 15 central-station nuclear power reactors were operable in the United States with an aggregate electrical capacity of over 4200 MW. Early in 1964, Jersey Central Power & Light Co. announced plans for constructing a 515-MW nuclear plant at Oyster Creek, N.J., to be built without government financial assistance. The company stated that a nuclear plant had been selected competitively with fossil fuel. Their economic analysis stated that the plant would generate electricity at less than 4 mills per kw-hr, competitive with coal at 200 per million Btu (British thermal units). Coal cost in 1964 for that region averaged 26.00 per million Btu. The Jersey Central report created wide interest in public-utility circles; nevertheless, no other nuclear plants were announced in 1964. However, in 1965, six nuclear plants were announced by utilities, followed by 26 in 1966, 29 in 1967, and 10 in 1968. By Sept. 30, 1969, 97 reactors were operable, being built, or planned. The cost of these, all committed by electric utilities, was estimated at about $12 billion. When constructed, they will have an electrical capacity of 72,000 MW. The unprecedented surge in power reactors that started in 1965 tapered in 1968, and only seven reactors were announced in

Jan 1, 1976

By H. F. A. Hergt, K. L. Sutherland, J. Rogers

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2&apos; *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest &apos;purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.&apos;." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952

By Edward Saibel

THE various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure, no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3,4 or on the energy required to form new surface.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agreement between calculation and experiment. It has been pointed out by several observers7 that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so - nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory Of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermo- dynamic theory of the tensile strength of isotropic bodies based on work of Born9 relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melt- ing phenomenon, Fürth obtains an expression for the rupture stress u, in the form [ ] where Q is the melting energy per unit mass, ? is the density, and µ is Poissons’ ratio. Fürth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By F. C. Blickensderfer

THE CHAIRMAN (B. B. GOTTSBERGER, Miami, Ariz.).-On your trip today through the Inspiration and Miami mills you have seen in actual operation the machines which represent the changes adopted in grinding methods in the Miami district from the beginning of operations in March, 1911. In one section of the Miami plant are three Chilean mills not yet discarded, representing the first machines adopted. In another section, pebble grinding is still in operation, while in the balance of the plant, pebbles have been replaced with iron balls. In all cases these machines are handling a feed which is the product of roll, grinding down to about ¼ in. in, size. The latest step in grinding in the district, You saw at the Inspiration plant, where in Marcy mills a filed, the larger pieces of which remain on a 2-in. opening, is being reduced in one operation to a product of which only about 3 per. cent. remains on the 48-mesh screen. A detailed comparison of the methods used at the two plants would be very instructive but our own work at Miami has not yet reached a point where such a comparison is possible, the reason being that our final product is not yet fine enough. By means of larger Hardinge mills operating in closed circuit with Dorr classifiers soon to, be installed in one section of the plant, we hope to obtain, under properly balanced operating conditions the same end result as at Inspiration. It, might interest you, however, to know some of the results we have obtained here by the substitution of balls for pebbles. With pebble grinding, using three 8-ft. by 22-in. mills, followed by one 8-ft. by 66-in. mill for regrinding the coarse product of the primary mills, we handled 636 tons per 24 hr. in one section of the plant. Substituting balls for pebbles in the first operation and using two mills in place of three we obtained a tonnage of .714 tons to the section. With the use of balls both in the primary mills and in the regrinding mills, the tonnage for one section was raised to 822 tons per day. Coincident with this increase in tonnage, we also obtained a greater efficiency. The use of pebbles in all mills showed 21.5 per cent. plus 48-mesh material in the final tailing, which figure was reduced to 13.9 per cent. for balls followed by pebbles, and to 4.6 per cent. with the use of balls both in the primary and regrinding mills.

Jan 12, 1916