Search Documents

By Max C. Eastman, V. H. Wilhelm

California had a record year in production and drilling activity, but the results have not been sufficient to keep up with the enormous increase in demand due to war activity. During the year, 164 dry wildcats were drilled, 80 dry wells in proved areas, 31 gas wells, and 1158 successful oil-well completions for a total of 1433 wells, compared with a total of 765 in 1942. With new discoveries of only 20,000,000 and production of 283,000,000 bbl. for the year, total reserves of California oil have decreased more than 250,000,000 bbl. However, revised estimates of the reserves of old fields indicate an increase in the state's reserves of I00,000,000 barrels. The completion of 1158 wells has served only to maintain the maximum efficient daily rate of production at 800,000 barrels. There is evidence in many fields that oil is being withdrawn too rapidly to obtain the maximum recovery, and more rapidly than is conducive to good production practice. Statistics for 1943 as compared with I942 are shown in the table in the next column, Supply and Demand Steadily mounting needs of the military forces and increased industrial consumption raised total demand for all petroleum products on the Pacific Coast to 914,000 bbl. daily in 1943. That all-time record demand was 149,ooo bbl. daily higher than in 1942 and 214,000 bbl. daily above 1941 demand. Despite restrictions due to shortages of critical material, crude-oil production was boosted from 680,000 bbl. daily in 1942 to 779,000 bbl. daily in 1943, the highest level in 15 years. However, the new crude supply plus natural gasoline production and imports from other states totaled only 840,000 bbl. daily, leaving a deficiency between supply and demand of 74,000 bbl. daily. That shortage had to be made up by withdrawals from inventories, which had been steadily depleted during the previous four years. Aboveground reserves, which totaled 159,574,000 bbl. on Jan. I, 1939, were down to ~8.000,000, bbl. at the end of 1943. Significantly enough, the greater part of that decrease occurred during the last six months of I9437 when more than 23,000,000 bbl. was taken from inventories of both crude and products. Although the size of total inventories on Dec. 31, 1943 might appear substantial, about 65 per

Jan 1, 1944

By R. E. Hathaway

INTRODUCTION For a number of reasons, the mineral processing industry has been slow to adopt significant automation of its processes. Most ore grinding operations can be operated manually so the pressure for automation to run the process has not been there. Furthermore, many plants had proven over years of operation that manual operation would produce a profit, so why automate? Until recently, the instrumentation necessary for automation of the grinding process was not available. All this has now changed, however. Increasing costs for labor, fuel, power, grinding media, reagants, and capital equipment have not been matched by the market price of the finished product. This cost-price squeeze has made it mandatory to reduce operating costs and improve the efficiency of the process to remain profitable. A number of other factors have added to the direct operating cost to make the problem even worse. These include environmental pressures to conserve natural resources and reduce smelter stack emissions; increased competition--especially from developing countries, varying economic conditions, stockpiling, governmental controls, and to top it all off, lower grade ore bodies. Although many of these other influences are good overall, they take their toll in cost per ton of delivered product. Fortunately, many operators are finding the solution to the cost-price squeeze in instrumentation and process control. Automated processes yield tighter spec. products, require less operating labor, produce more product from a given plant, and reduce unit cost by increasing process efficiency. The plant manager has a "handle" on the plant through process control so that he can change operating modes as economics dictate by changing the set point of some process controllers. He can even respond to economic conditions by switching control strategies from one that maximizes production to one that maximizes recovery, or minimizes unit cost, etc. This has all been made possible by the advent of on-line analytical instruments and practical process control computers. On-stream particle size (1), x-ray, and silica analyzers are now available and in use in many plants. Digital computer hardware and software has become practical so operators can use it without trying to become computer experts. This chapter describes the approach toward design and implementation of automatic grinding circuit control that has proven to be the most cost effective, based upon results from a number of

Jan 1, 1982

JULY was a month of great turmoil, both economic and political, in many parts of the world. Instead of conditions improving, they seem to have been getting worse. In Ireland, civil war is still in progress. Germany was in the throes of a political upheaval. The meaning of the assassination of Rathenau became clear. It evinced the development of a class struggle between the bourgeois and socialistic parties which may rock the country to its foundation and will increase the difficulties of arranging things with the French and solving the reparations problem. In Poland, a similar contest is developing. Austria is already so completely contaminated by the socialist element that it is unable to get outside assistance and is thus falling into a state of despair but little short of what prevails in Russia. The conference at the Hague came to an abortive end for the reason that it was impossible to discuss affairs with the Russians in any reasonable way. The Germans declared their inability to meet the reparation payment that fell clue on July 15 and the Commissioners for the Allies granted them an abate-ment of a portion thereof and are listening attentively to the supplication of the Germans for a moratorium of one or two years. In the United States, July was a month of widespread labor troubles, accompanied by a great deal of disorder and violence, which led to detachments of the National Guard being called out in several states. The railway shopmen, about 400,000 in number, struck on July 1. The road maintenance men decided not to strike, but many thousands of them quit work without the sanc-tion of their union. There were more strikes in the textile industry in New England and in similar industries all over the country. Early in July, it was estimated that about 1,250,000 men were out on strike. The coal strike continued. Early in the month the President summoned operators and miners to Washing-ton and submitted a plan for the compromising of disputes. After a week's consideration the miners re-fused flatly to agree to anything. The majority of the operators consented to accept the proposed arbitration, but a minority refused. Following this abortive at-tempt the President dismissed the conference with the injunction "to return to your mine properties and resume operation." Production has not increased.

Jan 8, 1922

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By Robert E. Allen

The organized curtailment of California oil production is not yet one year old but during its first year it has accomplished so much that it is now firmly established as an agency of economic efficiency. The principle of cooperative curtailment has been adopted by other states and it is safe to say that the principle will continue as long as the demand for petroleum is notably less than the potential production. It' is interesting to note that this same principle of regulating supply to meet demand is now being urged for other industries, such as agriculture and mining. Since Oct. 31, 1929, when curtailment was instituted by the oil producers of Santa Fe Springs and Long Beach in an effort to avert the disaster of ruinously low prices which confronted them, there has been a constant and increasingly effective curtailment program in California. Prior to that time a notable effort toward the restriction of oil production was made under the direction of F. C. Van Deinse during the early summer months of 1929. A considerable reduction of oil output was recorded as the result of this effort, but because of incomplete cooperation and the discovery of still deeper zones at Santa Fe Springs the effort was abandoned; flush field production became unrestrained and prices soon fell to low levels. This initial curtailment movement was educational and experimental. It showed all operators a way out of their overproduction difficulties and developed the principles followed in later curtailment efforts. Thus it was that only a few days after their oil had been reduced to 60 c. per barrel, the operators of Santa Fe Springs got together and agreed to restrict their current production of more than 270,000 bbl. daily to not more than 150,000 bbl. daily. The operators at Long Beach followed the same course a few clays later and agreed to limit their production to not more than 110,000 bbl. daily. The Santa Fe Springs operators chose H. P. Grimm as umpire and director of their proration program. Neal H. Anderson was chosen umpire for Long Beach. Since that time, as the need for curtailment has increased, practically every field of the state has come under the curtailment of these two umpires. Curtailment of the Elwood and

Jan 1, 1931

By John Campbell

An approximate theoretical model is proposed to quantitatively predict freezing ranges Tf and hydrostatic tensions P developed within solidifying binary alloys, allowing for a certain amount of diffusion of solute in the solid during solidification. The maxima in ATf and AP as functions of composition are shorn to occur at smaller solute concentrations than would be expected from the equilibrium diagram, and are found to correspond closely to experimentally observed maxima in microporosity. THE freezing range of simple binary alloys appears to have been little studied, except for certain indirect observations on the defects, particularly microporosity and hot tearing, arising in long freezing range materials. Two theories relating to the freezing range of alloys and its effect upon porosity are reasonably well established, and appear to have been held in isolation from each other: a) From purely equilibrium considerations early researchers expected that an increase in solute content of an alloy should increase the freezing range (defined here as the equilibrium freezing range ?Tf = Tl-Ts where TL and Ts are the liquidus and solidus temperatures, respectively) and thereby increase the width of the pasty zone for a given set of conditions. This in turn should increase the difficulty of feeding the residual liquid through the dendrite mesh to compensate for the contraction on solidification, and consequently tend to increase the observed amount of porosity. From qualitative observations on steels Czikel1 reports an increase in porosity with increasing carbon content up to 0.46 pct C. More careful measurements by Whittenberger and Rhines2 on fourteen different alloy systems showed an approximately linear relation between ?Tf and pct porosity (although unfortunately the precise experimental data is not given). b) Conversely however, other authors3"5 propose that porosity is reduced by the presence of increased amounts of eutectic present at the final solidification temperature. Lees7 and Bochvar6 claim that the hot tearing of alloys is similarly reduced. Scheuer8 has put forward a theory to explain this effect, Fig. 1. The argument is basically that solidification progresses on a plane front through a relatively open dendrite network and is thus (the argument is not developed more explicitly) easier to feed. One would expect effect a) to operate at low solute contents, and b) to be important at higher solute contents, so that at some critical composition a max-

Jan 1, 1970

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

THE vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.1 These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The major domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War II, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1947

By Daniel D. Pollock

The il'lott and Jones theory of thermoelectricity predicts that the absolute thermoelectric power of alloys of transition and noble metals should be a maximum when the concentration of the noble metal is approximately 55 to 60 at. pct. An examination of the emf of a series of relatively pure alloys of copper and nickel shows that the predicted maximum occurs at about 57 at. pct Cu. This excellent agreement with the theory is considered to substantiate the Mott and Jones theory of thermoelectricity for binary alloys of transition elements. This theory is extended to show that the emf behavior of dilute, ternary copper-nickel base alloys, which contain approsimately 60 pct Cu and 40 pct Ni, may be described in terms of a scattering mechanism. The scattering effect of a third element is demonstrated to be a function of its valence and its period in the periodic table. Small amounts of solute elements have additive scattering effects upon the emf of the Cu-Ni base. The Mott and Jones equation is modified to include this scattering parameter. This adaptation accurately describes the thermoelectric behavior of ternary and quaternary CLL-Ni base alloys. An empirical form of the modified Mott and Jones equation is derived which permits the calculation of thermoelectric power with an average error of less than 0.4 pct at 500 "C. CONSTANTAN has long been used as a thermocouple element. Its approximate composition varies from 50 pct Cu, 50 pct Ni to 65 pct Cu, 35 pct Ni. Small amounts of manganese, iron, and other elements have been used to modify the composition in order that the resultant emf vs platinum conforms to nationally accepted table. Adjustments of this type are made on a purely empirical basis. Constantan was originally made in Germany and was imported into this country for thermoelectric and electrical resistance purposes. During World War I, the supply of this material became seriously depleted. The work of Bash4 was done in this period in order to develop a satisfactory substitute for the imported material. Bash's empirical work on Cu-Ni alloys is still the basis for all commercial constantans made in this country. No reexamination of the electrical properties of this system has been made, despite the fact that it is now well known that Bash's alloys contained impurities which strongly affected their thermoelectric behavior.

Jan 1, 1962

By M. T. Martinson, I. W. Nicholson, C. J. Chindgren, F. P. Williams, L. C. Bauerle, S. F. Ravitz

The vanadiferous shales of southeastern Idaho and southwestern Wyoming constitute the largest known reserve of vanadium in the United States.' These deposits have never been exploited except for the relatively small amounts of vanadium recovered by the Anaconda Copper Mining Co. in the treatment of phosphate rock from southeastern Idaho. The maior domestic source of vanadium has been the sandstone ores of southeastern Utah and southwestern Colorado. Early in World War 11, it appeared that these ores could not meet the greatly increased demand for vanadium, so the investigation described in this report was undertaken to develop processes for the recovery of vanadium from the Idaho-Wyoming deposits. The utilization of these deposits became unnecessary, however, because of greatly expanded production from the Utah-Colorado sandstone ores and the continued availability of vanadium from other sources, chiefly Peru. The major use of vanadium is as an alloying agent in the manufacture of high-quality steels. Vanadium constructional steels usually contain 0.05 to 0.20 pct vanadium, which refines the grain and increases the strength, elastic limit, and resistance to shock and fatigue. Vanadium tool steels not used in high-speed work contain 0.10 to 0.60 pct whereas high-speed tool steels contain 1.0 to 4.0 pct. Vanadium compounds are used as catalysts (principally for the oxidation of SO2 to sulphuric acid and of naphthalene to phthalic acid) and in the paint, chemical, ceramic, dye, and printing industries. The selection of the particular ore deposit to be exploited would involve consideration of many factors besides the metallurgical results that might be obtained. Chief among these would be the reserves of ore available, the grade of the ore, and the mining costs. As very little was known about any of these factors, it was necessary to investigate methods of treatment of all the ores under consideration, working with samples obtained in the course of the exploration work, even though they were not positively representative of the whole deposit from which they were taken. Because of wartime conditions prevailing when this investigation was started, first consideration was given to processes that could be put into operation most quickly and would involve minimum use of strategic materials, even though these processes might not be the most economical.

Jan 1, 1949

By W. A. Ver Wiebe

The year 1938, with a production of 58,784,250 bbl. from 18,790 wells shows a slight recession from the high peak of oil production reached the previous year, when slightly over 68 million barrels of oil was marketed. The previous high peak had been reached in 1917 with a total of 45,451,000 bbl. Another still earlier peak was reached in 1904, during which year slightly less than 5 million barrels was produced and sold. The production of gas, on the other hand, probably reached a new peak during 1938 with a total of over 60 billion cubic feet. This peak, however, was not the highest peak, for during the year 1908 over 80 billion cubic feet was produced. Between these two high peaks the production dropped down to 16 billion cubic feet in the year 1921. The number of wells drilled during the year totals 1569. This figure is somewhat lower than the figure given in several trade journals because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly three-fourths (or 1107) of the total number of wells were completed as commercial oil wells (915 in western and 192 wells in eastern Kansas). The commercial gas wells completed number 50, of which 4 are in eastern Kansas and 46 in western Kansas. The remaining 412 completions include 130 dry holes in eastern and 282 dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year accounted for 70,000 bbl. of new oil for eastern and 1,220,000 bbl. of new oil for western Kansas. It is interesting to note in this connection that the number of wells completed in the state rose gradualIy to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918 when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak in 1937, the low point was reached during 1931, with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a new area whether it should be called a new pool or a long extension of an

Jan 1, 1939

By W. A. Dunkley, W. W. Odell

The sulfur content of coal is perhaps more important in the manufacture of illuminating gas than in any other coal-using industry. Whether the gas is made by the distillation of coal in retorts or ovens or by steaming incandescent coal or coke in the water-gas process, a portion of the sulfur present in the fuel always passes into the crude gas. Practically all the sulfur that remains in the finished gas is transformed into sulfur dioxide (SO2) when the gas is burned. Sulfur dioxide is a pungent suffocating gas and, if present in the air in any perceptible amount, is deleterious to health and comfort and damaging to house furnishings. SO universally is this recognized that laws regulating the amount of sulfur that may be permitted to remain in the gas are very generally in force. The capacity of a plant to purify gas frequently limits the selection of coal for gas making. This condition may arise from different causes. Some plants were originally designed to handle a certain grade of low-sulfur gas coal, and very little leeway was allowed for growth or for the use of inferior coals. Other plants, when built, had ample capacity to purify gas from relatively higher sulfur coals, but their output has grown so rapidly that their purifying capacity is now limited and only the low-sulfur coals can be handled. There is a great quantity of coal in the United States that would satisfy the requirements of the gas manufacturer, were it not for the high sulfur content. The coals containing less than 1 per cent. sulfur are becoming scarcer year by year and, in time, the gas industry will probably be compelled to use coals that are now considered out of the question. Sulfur Compounds in CRude Gas Sulfur exists in unpurified illuminating gas in a variety of compounds; chief of these are hydrogen sulfide (H2S) and carbon disulfide (CS2). In crude coal gas H2S is usually present to the extent of 0.5 to 2.0 per cent., by volume, equivalent to about 300 to 1200 gr. per 100 cu. ft. of gas. In carbureted water gas, the amount of sulfur compounds depends not only on the sulfur content of the coal or coke used, but also upon cite

Jan 1, 1920

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By Walter Kauzman

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications.1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By C. O. Brawner

Introduction The procedures used to design slopes in rock have only been developed over the past 10 years. Therefore, continued review and assessment of field experience by the publication of case studies is necessary to determine the accuracy of the theory and the application of the design techniques being used. Where failures have occurred, mine management should insist that the slides be 'back analyzed' to determine the shear strength parameters at failure. These values should be used for any pit design as they reflect site conditions more accurately than any other procedure. The previous papers have dealt with the basic concepts and factors that influence stability. To illustrate the application of these concepts in the study of practical stability problems, six ease studies have been selected for review. The examples include failure of tailings dams due to an earthquake, failure and redesign of a slope in overburden, review of failures of rock slopes, calculation of the amount of seepage into a pit and influence of the groundwater on stability, and the design of slopes for a proposed 2,500 ft. deep open pit mine. All but the first example are drawn from the authors personal experience. EXAMPLE 1 Failure of Tailings Dams Due to an Earthquake On March 28. 1965 a serious earthquake occurred in Chile with the epicenter located near the town of La Liqua, about 80 miles north of Santiago. The earthquake had a rating of 7 to 7.25 on the Richter scale. A record of the acceleration was taken at Santiago where a maximum horizontal acceleration of 0.18 g. was recorded. Many small mines are located in this region. Each of the mines provided impoundment storage for tailings with one to three dykes. As a result of the earthquake, most of the dams failed. The most serious failure involved two dams at El Cobre where more than 2,700,000 cu. yd. of tailings flowed into the valley, travelled over 7 miles in a few minutes, destroyed part of the town of El Cobre and killed more than 200 people. The Chilean government commissioned an investigation into the failures. A summary of the findings was published by Dobry and Alvare7 in 1967 (1). The location of the earthquake and the tailings dams which were investigated is shown

Jan 1, 1971

By H. Landssberg

Subsidence caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a preliminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem. The Problem To systematize an investigation regarding the effects of mine excavations two different aspects have to be dealt with: (1) the subsidence of the immediate roof above the workings, affecting the safety of the workers and the progress and efficiency of the operations; (2) the subsidence of the surface, which is also, from the point of time, the second event. The immense importance of surface subsidence as regards the impairment of surface structures of every kind in a mining area is self-evident. Both effects result from reactions of the strata overlying the excavations and they depend mainly on the extent of the excavations and the structure and geological condition of the strata. It has been stressed repeatedly, in this country principally by G. S. Ricel,† that for the understanding of the phenomenon of subsidence accurate surveys are the most urgent necessity. In the past, however, at least in the normal course of mining operations, these surveys have been very crude. The control of the roof in the mine is left to the observation of the behavior of the timber, warning cracks and sounds in roof and walls and to the general judgment and experience of the worker and his supervisors. In any given case this may or may not be sufficient to prevent fatalities but certainly it does not give any accurate information as to what is happening in roof and strata. On the surface, principally in endangered areas, surveys have been conducted more frequently, but also in this case usually weeks or even

Jan 1, 1936

By David J. Mack

A survey and critical appraisal of published information about Young's modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young's modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young's modulus. CalculatioX oP YouNg's Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess'enden4',~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By M. R. Geer, H. F. Yancey

INTRODUCTION The maximum yield of washed coal and the required ash and sulfur contents are the only performance factors of direct, immediate interest to any operator. Yet since the turn of the century coal preparation engineers have repeatedly sought more sophisticated performance criteria that could be used to draw comparisons between different cleaning operations and to permit generalizations about types of cleaning equipment or kinds of coal. Proliferation of efficiency formulas resulted. Hardly a year goes by, and certainly not an International Coal Preparation Congress, without the introduction of some new formula or some new concept of an existing criterion. This is merely the usual quest for improvement, because the performance criteria available today, although highly useful, are imperfect. Moreover, they are not as widely understood as they might be. The First International Coal Preparation Conference, which was held in Paris in 1950, accomplished a great deal toward establishing uniformity in terminology and methods of expressing cleaning results; the proceedings of that conference provide a wealth of detailed information on the various performance criteria, their uses and their limitations. For ease of discussion, the various performance criteria can conveniently be classed according to the degree to which they are dependent on the density composition of the raw coal treated. Some are directly dependent, some are only indirectly dependent, and some are, under certain circum- stances, essentially independent. DEPENDENT CRITERIA The yield and ash content of a washed coal are directly dependent on the washability characteristics of the raw coal from which it is derived. Thus, they are manifestly unsuited to comparing the performance of different plants, because no two plant feeds are the same. In fact, yield and ash content, by themselves, are inadequate for even routine day-to-day control. The continuous variation that occurs in the amount of impurity in raw coal, and sometimes in the float ash, make it impossible to tell whether a reduction in yield or an increase in the ash content of the washed coal results from any malfunction or misadjustment of the cleaning equipment. Recovery Efficiency For many years the most popular performance criteria that are only indirectly dependent on the washability characteristics of the raw coal have been efficiency formulas. Of the many that have been proposed, the one advanced by Fraser and Yancey in 1923 has had the widest accept-

Jan 1, 1968

By H. Landssberg

Subsidence caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a preliminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem. The Problem To systematize an investigation regarding the effects of mine excavations two different aspects have to be dealt with: (1) the subsidence of the immediate roof above the workings, affecting the safety of the workers and the progress and efficiency of the operations; (2) the subsidence of the surface, which is also, from the point of time, the second event. The immense importance of surface subsidence as regards the impairment of surface structures of every kind in a mining area is self-evident. Both effects result from reactions of the strata overlying the excavations and they depend mainly on the extent of the excavations and the structure and geological condition of the strata. It has been stressed repeatedly, in this country principally by G. S. Ricel,† that for the understanding of the phenomenon of subsidence accurate surveys are the most urgent necessity. In the past, however, at least in the normal course of mining operations, these surveys have been very crude. The control of the roof in the mine is left to the observation of the behavior of the timber, warning cracks and sounds in roof and walls and to the general judgment and experience of the worker and his supervisors. In any given case this may or may not be sufficient to prevent fatalities but certainly it does not give any accurate information as to what is happening in roof and strata. On the surface, principally in endangered areas, surveys have been conducted more frequently, but also in this case usually weeks or even

Jan 1, 1936

By N. Nemeth, L. L. Sirois

The role of the filter medium in continuous-vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and filter cloth are discussed. Due to negative pressure differential, gas bubbles evolve in the slurry, constrict passages in the filter cake and medium, and further restrict flow through the tortuous channels. Filtration is a liquid-solid separation process taking place at a porous medium under a pressure differential. The liquid passes through the medium; the solids are retained on the medium as a partially dewatered cake. Filtration is far from a simple process and has been described in terms ranging from "complex" to "subtle." Because of the many variables involved, no unified filtration theory has been developed, and the filtration process is still considered very much an art. In industrial filter design, basic relationships, whether derived for idealized conditions or developed empirically, are usually adapted to suit local conditions. In the mining industry where continuous-vacuum filtration is the main dewatering process, the physical state of the concentrates and the relatively low pressure differentials permit the assumption that the cakes are noncompressible, an assumption which leads to the use of theoretically sound rate equations. Notwithstanding this simplification, there are other problems, unique in the application of vacuum to dewatering, and until now completely ignored, which demand special attention. The basics of filtration involve the capture of solids on, while permitting the flow of liquid through, a porous layer of cake and cloth. Flow is determined by the structure of the solids which make up the cake and the particles permanently attached to the cloth. The problem of this structure, essentially one of solid geometry, has been considered insoluble by Hatscheckl as early as 1907 and by Freshwater as recently as 1967. Since cake structure is determined by the slurry parameters, that problem is far too large for inclusion in this study. For theoretical considerations, uniform buildup of the filter cake must be assumed; and for efficient practical operation, the resistance of the medium must be kept constant over long periods. The latter can be achieved by careful selection of the filter cloth, since the greatest part of the total filtration resistance will develop at the cake-cloth contact. This paper discusses the role of the filter medium in continuous vacuum filtration and the special circumstances which influence the resistance to flow through the porous cake and the filter cloth.

Jan 1, 1971

By B. F. Oliver

Equilibrium and kinetic segregation coefficients for the dilute high-temperature system tantalum in iron have been experimentally determined in a levitating zone melter. The equilibrium segregation coefficient, ko, is 0.43 * 0.03. Planar interface solidification is possible up to a freezing velocity of 4 in. per hr but not at 6 in. per hr. Precise concentration control of the solid is possible over this range of freezing velocities. The momentum boundary layer thickness, and the diffusion boundary layer thickness, 6, are such that either 6, > 6 or ALTHOUGH considerable data exists in the literature concerning the stability of planar-solidification fronts, little data exists for high-temperature metallic systems. The study of fundamental aspects of solidification in high-temperature iron-base systems is complicated by the extensive solvent power of liquid iron. In order to minimize such effects a levitating zone melter was used to study the segregation of tantalum in iron.' The solute tantalum was selected because: 1) the ko value was, according to the literature, initially thought to be less than 0.1, thus increasing the precision of the method used;2,3 2) the vapor pressure and is a constant, fixed by induction stirring, 6, the diffusion boundary layer, is 5150 u. At 400 rpm and 6 in. per hr freezing velocity the cast structure exhibits circular macroporosity and banding concentric with the axis of the rotation of the interface. Electron-beam microprobe analyses indicate that the tantalum content is highest at the center of rotation (1.2/1) and decreases with increasing radius as the fine-grained bands become sharper. This entire structure exhibits microseg-regation of tantalum. of tantalum in 1 atm of H2 is small, assuring conservation of solute during redistribution; and 3) spec-troscopic analyses were available for the appropriate range of tantalum considered. Additional objectives were 1) to determine kinetic segregation coefficients for well-stirred zones with constant boundary conditions and thus quantitatively calibrate solute-segregation behavior in the levitating zone melter, and 2) to examine the range of freezing velocities over which smooth solid-liquid interfaces could be controlled in an iron-base alloy under the restrictions of the thermal gradients imposed while levitating a zone. The single-pass zone-melting method was used to calculate individual k values.'

Jan 1, 1964