Search Documents

By D. D. Button, L. D. Jaffee

INTEREST in the use of graphite as a high-temperature engineering structural material has recently increased markedly. However, actual use of this material has been limited, in part because information about its high-temperature mechanical properties has been lacking. The information needed includes not only reliable values for the properties, but also how to control these properties. Malmstrom, Keen, and Greenl have reported on the tensile and creep properties of some graphites above 2700° F (1500°C). They observed measurable creep under tensile loading at 4000 OF (2200 °C) and higher, with elongations of about 7 pct at 4500°F. Their typical elongation-vs-time curve showed the normal three stages of creep found for many metals at elevated temperatures. The specimens used were heated by passing an electric current through them. This method of heating caused a significant difference between the surface and axis temperatures, and may have affected the results. More recent work by kattus, in which the specfinens were also heated by their own resistance, showed very little plastic deformation for either slow or fast tensile testing or for creep testing. Work at this Laboratory, already reported,3 showed that for temperatures above 4500 "F and under conditions of slow tensile loading some commercial graphites exhibited elongations up to 20 pct. The work reported here is the continuation of a study of the tensile creep behavior of some commercially available synthetic graphites at temperatures up to 5300°F, and is preliminary to a more systematic investigation of the variables governing the high-temperature mechanical properties of graphite. MATERIALS TESTED The tests were conducted on six blocks from four lots of synthetic graphite bearing four different commercial-grade designations. These blocks were selected because their tensile stress—strain properties had been determined in previous work.3 Table I pre- sents the available information, supplied by the producers, on the processing of these materials. Also included in this Table are the densities and the tensile strengths at room temperature and 4500°F determined by the authors. EXPERIMENTAL TECHNIQUE The furnace used to heat the specimens for testing is shown in Fig. 1. The heating element was a graphite tube, 3-in. OD by 2 1/2 in. ID by 24 in. length. A spiral was cut into the 6-in. center portion of this tube to provide a high-resistance sec-

Jan 1, 1961

By G. W. Ostroot, S. Shryock

Cementing deep, high-temperature oil wells where static temperatures range from 350 to 400F has become routine in the part decade. In the United States there were 271 wells drilled deeper than 15,000 ft during 1963. Many of these wells had static temperatures higher than 400F. Bottom-hole static temperatures near 700F are now realities in the geother-mal (steam producing) wells of California's Salton Sea area. The detailed planning initiated prior to drilling the wells is discussed together with the methods, materials and equipment used in solving the cementing problems which are encountered. Data are also presented that lead to development of cementing compositions that provide adequate thickening time, do not retrogress in strength, and maintain low permeability under these extreme temperature conditions. Field data include the cementing programs used on eight relatively trouble-free geothermal steam wells in the Salton Sea area. INTRODUCTION Not too many years ago cementing oil wells with temperatures in the range of 300F caused considerable anxiety. In some areas of the United States it is now fairly common to cement wells having bottom-hole static temperatures in excess of 400F. We are now confronted with the problem of cementing wells with temperatures ranging from 500 to 700F. Temperatures in this order of magnitude are often found in geothermal steam wells. From where does this extreme heat emanate? There are many theories as to the source of this steam flow. The most widely held views are: (1) heat- ing of ground water fairly close to the surface by an intrusive mass of hot rock; (2) steam generation from a reservoir of metamorphic rock, normally found below 25,000 ft and not at the shallower depths of the Salton Sea reservoir; and (3) high-temperature gases (water vapor) escaping and migrating from molten or semi-molten rock (magma) at a considerable depth. Of these. No. 3 seems to be the most generally acceptable explanation. Heat from springs and fumaroles has been used for years as a means of heating and cooking; however, significant progress in harnessing the vast power of underground steam reservoirs has been relatively slow. The first large-scale attempt to use the heat generated by steam from wells was made in Italy around the beginning of the 20th century. In excess of 250,000 kw of electrical power is now being produced from holes around Larde-rello, Italy. Another very active drilling program was initiated in the volcanic area of New Zealand in 1949.' Natural steam for power projects in the United States began in the early 1920's. An early commercial steam field is located at the Geysers, approximately 75 miles north of San Francisco, an area discovered in 1847 and used for many years as a health resort. Steam originates from 15 wells that have been drilled since 1957. The present output from this project is 25,000 kw. Success of the Geysers operation has been responsible for several companies taking a careful look at the feasibility of producing steam for power generation in the Salton Sea area of Southern California's Imperial Valley. Geothermal steam activity in this latter area began in 1961 when O'Neill, Ashmun and Hilliard completed Sportsman No. 1, at that time the hottest wellbore in the world.' Since its References given at end of paver. completion seven additional wells have been successfully completed in this area. Many problems encountered in drilling steam wells had to be overcome to make the ventures successful. Formation temperatures encountered in the Salton Sea seemed to be a straight-line function (a gradient of 13F per 100 ft of depth).' This imposed severe conditions on all aspects of drilling and completion. This varied, to some extent, from gradients in the older geothermal areas. Not to be overlooked is the effect of these temperatures on casing creep or elongation by thermal expansion (Table I), because standard API flanged wellhead equipment makes no provision for this kind of performance. Floating equipment was redesigned, and changes in types of downhole equipment were made in an effort to eliminate anticipated problems. In the later completed wells, standard oil-well cementing equipment has been used. During the early development of geothermal steam wells there were some problems resulting from blowouts. However, these were eliminated in the deeper Salton Sea wells and no problems were encountered with the drilling mud. A sodium surfactant mud was used on the Sportsman No. 1 to drill from 2,690 to total depth. Nevertheless, it was necessary that a cooling system be added and the mud cooled before circulating it back into the well. The difficulty in evaluating the size of the steam area and its potential in terms of pounds of steam and years of productivity still has not been resolved. Economic complexities have also entered into the steam play in the Salton Sea. The wells at the Geysers were drilled at a cost of $15,000 to $20,-000, whereas the Salton Sea wells will cost more than $150,000. This cost differential has to some extent been accounted for because of the heavily

Jan 1, 1965

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry's fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

By T. M. Girdler

IN THESE perilous days of world- wide uncertainty, this Institute and the profession represented by it take on new importance in the economic life of the nation. I have long been impressed by the fact that the objects of the A.I.M.E. are purely professional and scientific. The country has benefited from your honorable tradition of adherence to those objectives over a period of 68 years. The Institute's policy of refraining from controversial matters - has made possible the serious, balanced, and uncolored consideration of the particular problems that come before it.

Jan 1, 1939

By Waldemar Lindgren

IN spite of a world production of lead amounting to 1,300,000 tons, of which the United States produces slightly less than one-half, it appears that the mines at present are hardly able to supply the demand. For this there are several reasons. The lead deposits, geologically speaking, were formed comparatively near the surface under conditions of lower temperatures, with the richer deposits often residuary; that is, enriched by surface water, and consequently soon exhausted. Lead is practically absent from a great part of the world. The great Canadian shield, the eastern part of the Dominion, contains practically none. Scandinavia contains no lead. It is absent from geo- logical formations of great age, but does occur in large quantities in the deposits in the Rocky Mountain region. These deposits are, more or less directly, of igneous origin, but here, too, there is a tendency of the lead shoots to concentrate in the upper part, and when they go down the deposits turn to zinc-copper and some other metals. This is one of the best established facts of economic geology. The deposits of the Mississippi Valley district, from Kansas-Oklahoma, to Canada, are in comparatively accessible limestone beds, at a depth seldom more than 500 ft. Therefore, the lead is easily mined but more easily exhausted.

Jan 1, 1926

By J. K. Kerver, J. S. Osoba, J. G. Richardson, J. A. Hafford

A detailed study of a number of methods of relative permea-abilitv measurement has been made in a search for the tech-niqrle most suited to routine analysis of cores taken from reservoir rock. It has been found from tests run on the same samples of core material by a number of techniques that the Penn State, Hassler, Hafford, and dispersed feed techniques all yield results which are felt to be reliable. Conditions under which the faster single core dynamic technique may be used are described. Further work on the calculation of relative permeabilities to oil from data obtained by the gas drive method is needed before this latter rapid method can be utilized. Correlations between theoretical studies and experimental results have been obtained in studies of the boundary effect. pressure distribution in two-phase flow, and gas expansion effects. Previous conclusions that the effects of the outflow boundary could be made negligibly small have been substantiated. Results of experimentally determined oil and gas pressure distributions along a core sample during flow are presented. Further studies of the effects of rate of flow in the measurement of relative permeability-saturation relations have shown that results are independent of the rate of flow as long as the flow rate is below the point where inertial effects commence. An analysis of the effects of a severalfold expansion of gas along the flow path indicates that while saturation gradients are induced in the test sample, the errors caused by this phenomenon in relative permeability measurements are small. INTRODUCTION Many pages of literature have been devoted to pointing out the need for relative permeability-saturation relations in reservoir engineering. One of the most attractive ways of obtaining this information is by the analysis of samples of core material taken from the formation in question, and again literature has described man); methods for obtaining these data. It is the purpose of this paper to present the work that has been done in the study of some of these published methods together with some other methods that have been recently developed in this laboratory. Also, a study of some of the factors that influence the laburatory determination of relative permeability-saturation relations is presented. FACTORS WHICH AFFECT LABORATORY STUDY OF FLUID FLOW THROUGH RESERVOIR ROCK To determine relative permeability-saturation relations of samples of reservoir rock in the laboratory, it is important to know what factors affect these measurements in order that the magnitude of these effects can be ascertained and steps then can be taken to eliminate or, in some cases, to minimize them. The factors that have been investigated are the boundary effect, the effect of gas expansion. and the rate effect. Boundary Effect In laboratory experiments in which two immiscible fluids are flowed through a porous medium, there exists a discontinuity of capillary properties at the outflow face. This discontinuity exists became the fluids pass from a region of finite capillary pressure in the sample to a region of zero capillary pressure in an open receiving vessel. The capillary forces existing in the core caupe the rock to tend to retain

Jan 1, 1952

By J. H. Scaff, H. C. Theuerer

Germanium may be reversibly converted from n to p type by heat treatment. Data for the conversion and the associated changes in resistreatment.tivity are given and the results are interpreted in terms of changes in the donor-acceptor balance. MEANS for controlling the electrical properties of germanium in a predictable manner are of interest because of the increasing utilization of this element as the semiconducting material in electrical devices. Since both the mechanism and the magnitude of the electrical conductivity depend upon the kind and quantity of impurities present, the conductivity usually is adjusted by first carefully purifying the germanium, and then, by standard alloying procedures, adding the elements desired. The elements usually added are from the third or fifth periodic groups depending upon whether p- or n-type germanium is desired. However, in the development of germanium rectifiers during the war, it was found that it was possible also to modify reversibly the conductivity of germanium and even to produce conversion from n to p type by heat treatment.1,5 Since then a detailed study of this effect has been made. The data are presented in this paper and an explanation is offered for the effects observed. Preparation and Experimental Procedure The method used in preparing the germanium ingots for this investigation has been previously described.' The method consists essentially of (1) reduction of GeO2* and (2) preparation of a 50-g ingot from the reduced material. Graphite containers are used in both steps. In the first step the GeO2 is reduced in hydrogen at 650 °C to form a sponge germanium which, to assure complete reduction and to obtain massive materials, is fused subsequently in the reduction furnace by gradually raising the temperature to 1000°C. The button of germanium thus obtained corresponds to a yield of 99.8 pct. The final ingot is prepared by fusion of the germanium button in a helium atmosphere. A cylindrical crucible in a vertical silica tube furnace is employed and the crucible is heated by an external induction coil. The ingot is solidified from the bottom upward by raising the induction coil at a constant rate with power to the coil kept at a fixed value. In such ingots, segregation is normal and most of the impurities are concentrated in the last region of the ingot to freeze. It follows then that the major portion of the ingot is purer than it would have been if freezing had occurred in a random fashion. Moreover the orderly advance of the freezing surface during solidification establishes in the ingot a succession of surfaces of constant composition, if it is assumed that the liquid is homogeneous and that diffusion in the solid is negligible. Therefore, some information on the distribution of impurities in the ingot may be acquired by determining the shape of the solid-liquid interface at different stages of solidification. This is of importance because the concentration of impurities will be seen to affect the response of germanium to heat treatment. Such information is difficult to acquire by direct means, for the impurities responsible for the electrical properties of germanium prepared in this way are present

Jan 1, 1952

By W. R. Webb, M. O. Peterson

WHEN men drive haulage equipment ranging up to 22 tons in an open pit operation, they must live with the realization that their safety is dependent upon the machines they drive and how well they operate them. The hazards inherent in their jobs must be recognized, met, and defeated. It comprises a never ending struggle toward perfection-an almost un- obtainable goal. The Jones & Laughlin Benson Mines, at Adirondack State Park in New York, created a safety program which resulted in only one three day lost time accident from April 1948 to April 1952. At the very start of the program, management of the open-pit operation recognized the hazards existing at Benson. The program was designed to meet each danger. With a knowledge of the problem faced, the process of minimizing each facet was planned along lines of maintenance of equipment and training of personnel. Its success is evident. In the ever-present struggle, care and maintenance of machines and application of experience to new equipment design are mainstays. Truck Haulage Benson produced 2.9 million tons of crude iron ore and 1.6 million tons of waste in 1951. To do the job, truck mileage reached 500,000 miles. The tremendous mileage emphasized to safety planners, the fact that the more work done, the greater the possibility of risk in haulage operations. Instrumenting the aim of the safest equipment possible is a methodical servicing program. Like other segments of the drive, the servicing program is based on greater production with fewer accidents. Every truck is serviced at least once per eight-hr shift. Examination includes inspecting and tightening wheel studs, checking tires, steering apparatus, lights, brakes, wipers, heaters, fire extinguishers, and refueling. A running history of the equipment's operating life is kept in the form of service and maintenance records. Machine operators are constantly on the alert for malfunctioning of units. At the first sign of trouble the truck is returned to the garage for exchange. No truck functioning incorrectly is kept on the line, regardless of its shift check schedule. The program resulted in a reduction of the number of costly overhauls and cut down the number of haulage accidents. Miscellaneous Mobile Equipment Auxiliary units, operating within the pit, have presented definite safety problems. The highest accident rate in the pit occurred on trucks carrying water and bits to the churn mills. The weight and awkwardness of bits and drill stems, combined with remote delivery points were direct causes of numerous accidents. Here, the problem has been one of equipment handling, rather than haulage. All air compressors for secondary drilling are truck mounted, facilitating mobility. In addition to making it easier to move the equipment, truck mounting has eliminated many of the hazards connected with relocating machinery. By making air compressors independent of other units, drilling operations have been speeded up considerably. Unseen rocks in the path of moving vehicles are a constant source of tire damage. At Benson the problem has been met by supplying each loading crew with a bulldozer for cleanup operations. The pitman directs the dozer operation, and when truck drivers back into loading areas, he serves as an extra set of eyes. Modern Truck Garage Provides Drive-Through Service Simplicity is the essence of any preventative maintenance program. At Benson, a modern garage, with a drive-through service bay simplifies servicing. Shift inspection of the 22-ton haulage units is accomplished with minimum delay and maximum thoroughness. Major repair work and periodic overhauls are done in the repair section of the truck garage. Crane facilities for handling heavy assemblies ease the job and add to the safety factor. Other mobile machinery,

Jan 1, 1952

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors' opinion it was prob¬ably at least 5 million tons. The total fuller's earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world's 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By AIME AIME

ON MAY 22 the American Institute of Mining and Metallurgical Engineers will commemorate the sixtieth anniversary of its founding at Wilkes- Barre, Pa., in May, 1871. The Directors have transferred the May meeting of the Board to Wilkes-Barre, and the Pennsylvania Anthracite Section has invited as many members of the Institute as can to be present at this time and to join with their fellow-engineers at Wilkes-Barre in the inspection trip through a portion of the anthracite district that has been planned. Ac- cess to Wilkes-Barre is easy, from nearby points, over excellent automobile roads, or by train. The distance from New York is only about 140 miles. , It is hoped to engage a special car for those travelling by train from New York, which will leave the Pennsylvania Station over the Lehigh Valley Railroad at 11:50 p.m., arriving in Wilkes-Barre the next morning. Return can be made from Wilkes-Barre by sleeper the same evening, arriving in New York Saturday morning. Other trains are available for those who prefer a daylight journey.

Jan 1, 1931

By AIME AIME

American Institute of Mining Engineers. (Organized in 1871, and Incorporated in 1905.) OFFICERS. For the year ending February, 1906. Directors JAMES GAYLEY (President), R. W. RAYMOND (Secretary), FRANK LYMAN Treasurer). T. A. RICKARD NEW YORK, N. Y. CHARLES H. SNOW NEW YORK, N. Y. R. W. RAYMOND NEW YORK, N. Y. (Terms expire February, 1906.) JAMES GAYLEY NEW YORK, N. Y. FRANK KLEPETKO NEW YORK, N. Y. FRANK LYMAN NEW YORK, N. Y. (Terms expire February, 1907.) JAMES DOUGLAS NEW YORK, N. Y. JAMES F. KEMP NEW YORK, N. Y. ALBERT R. LEDOUX NEW YORK, N. Y. (Terms expire February, 1908.)

Jan 1, 1906

By AIME AIME

THANKS to the excellent preliminary work of: the Division officers and the local committee the fall meeting of the Coal Division at Bluefields was a brilliant success. West Virginia was at its best with its beautiful mountains, good roads and foliage, just beginning to turn to autumn colors. The meeting began on time and was kept on time throughout. The papers were-well prepared and, being on subjects of live interest, provoked 'lively discussion. One factor in bringing this about was that they were not too numerous and that with one exception copies had been submitted in advance a sufficient time to permit of them having been studied. The Friday morning session was presided over by John .J. Lincoln of the Crozier Coal and Coke Co. and president of the Pocahontas Coal Operators Association. After brief announcements by Thomas H. Clagett, chairman of the local committee, regarding plans for the two day's involved, and by Howard N. Eavenson, chairman of the Division, the reading of papers was taken up.

Jan 1, 1931

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By Claude Ferquson

MORE men are killed and injured in the metal mines of the United States from falls of rock and ore than from any other cause. Dan Harrington, of the U. S. Bureau of Mines, recently stated that "falls of men and material continue to take about 50 per cent of the lives annually lost in our mines (coal or metal) and this kind of accident is now and has been one of the most difficult to prevent." The fact that comparatively little has recently been written on this important subject for the benefit of the metal miner is the incentive for the present paper. Little will be said that will be new, but I hope to place fresh emphasis on certain well-known' principles' and to reiterate and stress previously stated rules so that the average experienced miner, as well as his buddy who may not be so experienced,' will sit up and take notice. It is not within the scope of this paper to discuss mining methods from the standpoint of safety and the prevention of accidents from falls of rock. It is up to the mine management to select the system of mining best suited to the character of the ore deposit and its wall conditions. This is something that the miner can do little about; although in many mines the management encourages the workmen to make suggestions that will improve existing

Jan 1, 1938

"The Washoe Smelter is situated about two miles east of the City of Anaconda. The smelter site includes about 240 acres and peculiarly adapts itself in topography to the efficient handling of material. By reason of its being on a hill side it is possible to make the level of delivery of the product of one building the level of the charge floor of the next succeeding one.THE ORES: The ore treated comes principally from the Butte district and is hauled by the Butte, Anaconda & Pacific railway, a distance of twenty-eight miles, in trains of fifty 50-ton bottom-dump cars to the railroad yards at East Anaconda. At this point these trains are• split up according to their destination,—that is, as to whether they go to the concentrator and sampling mill ore bins, or to the storage bins. In each case they are made up into trains of eight or sixteen cars, according to the size of engine to be used, and are carefully weighed before delivery to their respective bills.Some idea of the magnitude of the works may be obtained from the following figures:Amount of ore that can be treated in 24 hours…12,000 tonsLime rock from adjacent quarries…2,300 tonsCoke used…500 tonsCoal for reverberatory use…500 tonsCoal for power use…50 tonsWater, per minute, 35,000 gallons.Men employed in and around Anaconda, 3,000. Monthly payroll for above, $300,000.00."

Jan 1, 1913

By Arthur F. Wendt

The following experiments and researches were originally conducted by Dr. Heinrich Rcessler, chief of the German Gold and Silver Parting Establishment at Frankfort-on-the-Main, for the sole purpose of abating the nuisance created by the discharge into the air of the sulphurous and sulphuric acids generated in the process of parting bullion by sulphuric acid. The results achieved have, however, an important bearing not only on this process, but are of value in the manufacture of sulphuric acid and sulphate of copper from sulphurous gases derived from any source. It has now been in successful operation for a term of years at Dr. Roessler's own works, and has been lately introduced with satisfactory results at the royal mints of Kremnitz and Munich, and the well-known establishment of Johnson Mathey & Co., of London.

Jan 1, 1884

By Wilbur H. Somerton

W. H. Somerton is to be commended for his application of the methods of dimensional analysis in combination with the results of laboratory drilling tests to obtain a significant formula for the rate of penetration for the process of rotary drilling. This formula is shown to be a consequence of a more general formulation developed by the discussor as a result of his investigations of the basic action of most methods of rock drilling by mechanical means—the momentary loading of a chisel-shaped tool on the surface of the rock at the bottom of the hole. Some of the author's conclusions are re-examined in the light of this general formulation. DRILLING RATE FORMULA The author selects a minimum number of the most significant variables associated with the rotary drilling process to set up his two dimensionless parameters. Only one variable is associated with the geometry of the bit —the bit diameter, D; only one variable is associated with the properties of the rock pertinent to drilling— the drilling strength, S; and only two independent variables are associated with the conditions of operation the weight on the bit. F, and the rate of rotation, N. The dependent variahle of interest is, of course, the rate of penetration, R. The results of the author's drilling tests show that the variable R that appears in the dimensionless parameter, RIND is approximately proportioned to the square of the variable, F, that appears in the other dimension-less parameter, F/D2S. This establishes the functional relationship between these two simple parameters that leads to the formulation of a third dimensionless parameter, RD1T2/NF1. This last parameter is a significant one for the rotary drilling process, in general, although the author properly limits the validity of his equations to his present test conditions. The author realizes that the numerical value of this parameter, C, is not a constant but may be a function of one or more additional dimensionless groupings of the many other variables associated with the rotary drilling process, e.g. some dimensionless measure of bit wear. The author's parameter is shown to be a special case of a more general dimensionless parameter, developed by the discussor. that is applicable to practically all methods of rock drilling by mechanical means, namely. RD2S/P. P is the rate at which mechanical work is done on the rock, and S is the drilling strength, a term originated by the discussor. S is defined as the ratio of energy input to the rock to the volume of rock broken

By AIME AIME

AT a recent meeting of the Utah Section. A.I.M.E., P. D. Nielson, general plant superintendent of the new Geneva steel plant at Provo, Utah, spoke on "General Operations of the Geneva Plant." Mr. Nielson explained that the plant was located at Provo, Utah, on account of railroad facilities, the proximity of coal, iron, and limestone, and the nearness of water for operating the plant. Water probably was the most important item in making the decision.

Jan 1, 1944

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970