Search Documents

By Max Ball

AN intelligent discussion of the oil situation and its needs, whether from the standpoint of the prospector, the operator, the engineer, or the public administrative officer, must be founded upon a knowledge of the law under which oil lands are obtained. A consideration of new legislation must be prefaced by an understanding of the present law and its results. This paper undertakes to present no new remedy for the ills of the present situation, no new solution of the problems the oil business is facing. It attempts merely to summarize the present law, its provisions, its origin, its development, and its effects. The discussion does not pretend to be exhaustive from a legal standpoint. It aims to avoid legal intricacies Which tend to confuse rather than clarify. It seeks but to present the essentials of the existing situation. The title to government lands known to contain valuable deposits of petroleum may be acquired only under the terms of the placer law as embodied in Section 2329 et seq. of the Revised Statutes. As a preliminary to considering the desirability of this situation it is profitable to examine into its origin. ORIGIN OF THE LAW Congress has left no room for doubt as to the legal applicability of the placer law to oil lands. The Act of Feb. 11, 1897 (29 Stat., 526), provides: "that any person authorized to enter lands under the mining laws of the United States may enter and obtain patent to land containing petroleum or other mineral oils, and chiefly valuable therefor, under the provisions of the laws relating to placer mineral claims."

Jan 6, 1914

By R. C. Hirschfeld, H. H. Einstein, R. W. Bruhn, R. A. Nelson

The objective of the model studies described in this paper is to determine the effect of planar discontinuities on the strength and deformability of a rock mass. A model material was used because it satisfied concurrently three requirements that available natural-rock samples did not: (1) low strength, which was desirable for minimizing the loads that had to be applied in the laboratory; (2) ease of producing test specimens with geometrically regular joint patterns; and (3) uniformity of the test specimens. The model tests were performed on specimens made from a single modeling material and tested under triaxial stress conditions with [u,=u,]. Results are presented in this paper for tests on specimens that had (1) a single joint set inclined at several angles to the major principal direction, including 0º and 90°, and (2) two joint sets that were mutually perpendicular, one set perpendicular to and one set parallel to the major principal direction. Several different joint spacings were used in each series. Future tests will include a series with two sets of joints that make oblique angles with each other and with the major principal direction. The results of model tests and tests on cores of jointed rock by several investigators (e.g., Müller and Pacher,l Moore,2 Krsmanovic and Milic,3 Hayashi,4 Rosenblad,5 Jaeger,6 and Lane and Heck 7, have contributed significantly to the design of these experiments, which are believed to be the first in which a comprehensive study has been made of the combined effects under triaxial loading of joint spacing and joint orientation (Fig. 1).

Jan 1, 1970

THE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently attempted to make a much too simple correlation between mineral discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail

Jan 1, 1941

By Harry Power

THE relative merits of air and natural gas as propulsive agents in pressure drive operations have been discussed for a number of years. When air or gas is introduced into the sand, various factors lead the operator to the selection of what he believes to be the proper propelling medium; but when the question of relative drive effect is raised, several physical and chemical premises must be taken into consideration in arriving at a conclusion as to the superiority of one medium over the other. Dow and Calkins1 and Beecher and Parkhurst2 have contributed fundamental experimental work on the effect of dissolved gas in lowering the viscosity and surface tension of crude oil. Herold3 and Tickell4 have indicated that whatever type of reservoir control obtains, gas plays other important parts in the movement of oil towards the well, namely: 1. The propulsive and expansive force of the gas. 2. The "Jamin effect," or resistance to the movement of oil in a porous media due to the formation of gas bubbles. When quantitative studies are made, parallel conditions must be selected whereby we may say definitely whether air is superior to gas as a driving medium, or vice versa. Examples of similar conditions are not easy to find in the field. However, in the laboratory we can make determinations which may lead to general conclusions when applied to the field. The- experimental and research work described here was started at the laboratories of the University of California in January, 1927, and completed in private laboratories at Tulsa, Okla., in February, 1928. The apparatus used was designed especially for the work.

Jan 1, 1928

By Frank R. Milliken

This paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, MacIntyre Development, Tahawus, New York. In early 1941, when world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their MacIntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. MacIntyre Development is at Tahawus, New York, on the headwaters of the Hud- son River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of.ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. Ore—types From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table I. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, in garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1949

By Donald L. Katz

The equilibrium constants developed by Souders, Selheimer and Brown1' have been very useful tools in predicting vapor-liquid equilibria during the past five years. Their equilibrium constants were computed by assuming ideal solutions and recognizing the deviations of vapors from ideal gas laws. The same fundamental concepts were used by Lewis and co-workers8 for predicting vaporization phenomena by means of fugacities. The equilibrium constant is defined by equation 1: y\x =K [1] in which K = equilibrium constant, y = mol fraction of a constituent in the vapor phase, x = mol fraction of the constituent in the equilibrium liquid phase. The equilibrium constants are a function of temperature and pressure and might be considered as replacing the ratio of the vapor pressure to the total pressure of Raoult's law. They may be used to compute the vapor or saturation pressure of a liquid or the dew point of a vapor for any pressure or temperature from the analysis of the mixture much as Raoult's law is used. Likewise, the quantity of a mixture that will vaporize at any equilibrium temperature and pressure and the composition of the vapor and liquid may be calculated. The purpose of this paper is to review the available equilibrium data of interest in petroleum production, to discuss the auxiliary physical properties of the hydrocarbons, and to present typical uses of the equilibrium constants. The particular applications chosen are the computation of the results of stage separation of crude oil and natural gas, the calcula: tion of a pressure-volume curve of a crude oil-natural gas mixture, and information gleaned from a consideration of reservoir equilibria.

Jan 1, 1938

By Frank R. Milliken

SCOPE THIS paper is a running commentary on metallurgical problems and developments, stressing ilmenite flotation, since the start of operations five years ago, at the mill of National Lead Company, Titanium Division, Maclntyre Development, Tahawus, New York. [ ] GENERAL In early 1941, when, world conditions threatened to cut off the supply of ilmenite (obtained largely from India) to this country, the National Lead Company started to develop and bring into production their Maclntyre Development. This operation supplied the bulk of the ilmenite used during the war period for the manufacture of the much needed titanium pigments. Maclntyre Development is at Tahawus, New York, on the headwaters of the Hudson River in the center of the scenic Adirondack Mountains. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. Operating tonnages and production have increased since 1943, however. Nearly 10,000 tons of ore and waste is broken and loaded daily in the open-pit mine. About half of this tonnage is ore, from which is produced nearly 800 tons of ilmenite concentrate and 1600 tons of magnetite concentrate daily. ORE-TYPES From an ore-dressing standpoint, there are five rather distinct ore types and two waste-rock types in the mine. The ore types are shown in Table 1. The anorthosite waste is a coarse-grained white rock, largely labradorite feldspar. The gabbro waste is generally finer grained, and contains, in addition to feldspar, 35 to 75 pct iron silicates such as hornblende, pyroxene, garnet and biotite. A minor mineral mineralogically, but important metallurgically, is apatite. A few calcite

Jan 1, 1947

By Frank F. Aplan

INTRODUCTION Coal is a solid, combustible mineral substance resulting from the degradation and alteration of vegetable matter largely in the absence of air. In this natural process of coalification, some non-combustible mineral matter is always associated with the combustible material. Coal preparation or cleaning is the process of removing this inert mineral matter from the coal. Preparation is highly successful in removing the large fragments of inert material, but is not very effective in removing the fine inorganic mineral matter intimately associated with the coal. Of the 600 million tons of coal produced in the United States every year, approximately one-half is produced by coal cleaning methods (1). The bulk of this tonnage is cleaned by coarse or intermediate gravity preparation methods (5 inches to 28 mesh, Tyler). Fine cleaning, say, -28 mesh, is done by shaking tables, washing cyclones, and flotation, or, until recently, the fines were either incorporated into the clean coal or simply discarded--not infrequently, the latter. In 1972, only 13 million tons of raw coal were cleaned by flotation in the United States, and from this 8.4 million tons of clean coal were produced (1). The percentage of clean coal produced by flotation in Europe (England, West Germany, Poland, U.S.S.R., etc.) is substantially higher. However, coal flotation has grown rapidly in the United States from only a few plants in 1950 to 31 in 1960 (2) and 66 in 1970 (1). Virtually all new preparation plants incorporate flotation into their basic flowsheet. The essential difference between ore and coal flotation is that for ores the entire tonnage is ground to flotation size, whereas for coal

Jan 1, 1976

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By William L. Fink

Nickel is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting properties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investigations of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available. Previous Investigations The entire aluminum-nickel system was studied thermally and microscopically by Gwyer.1 At the aluminum end of the system he found the intermetallic compound NiA13. He found a eutectic at 6 per cent nickel with a melting point of 630" C. A slight thermal arrest, which he could not explain, was also noted in alloys from 2.5 per cent to 41.9 per cent nickel at 550" C. Bingham and Haughton,2 in a later investigation of alloys of aluminum with copper and nickel found the eutectic concentration of the binary aluminum-nickel system at about 5.3 per cent nickel. The melting point of the eutectic was about 633" C., or slightly higher than that found by Gwyer. Although the solid solubility of nickel in aluminum could not

Jan 1, 1934

By A. L. O’Neil, J. A. Wineland, A. B. Arnold

Movement of water through the Tehachapi Mountains was one of the most challenging parts of the planning, design, and construction of the California Aqueduct. The California Aqueduct is the main artery of the California State Water Project, which will move water 444 miles from the Sacramento-San Joaquin Delta into the arid and semiarid, densely populated parts of Southern California. The $2,000,000,000 project, designed and constructed by the California State Dept. of Water Resources, was started in 1957 at the Oroville Dam site and is now well past the halfway mark in construction. Water is now being delivered from the California Aqueduct to portions of the San Joaquin Valley. The California Aqueduct is scheduled for completion in 1972. Tunnels on the Tehachapi Crossing are often overshadowed in engineering descriptions of the Crossing by the tremendous importance and engineering significance of the Tehachapi pumping plant which will pump water through the tunnel system. For purposes of this paper, it will suffice to say that the plant is designed to lift 4100 cu ft of water per sec up approximately 2000 ft, making this the highest pumplift in the United States and one of the largest in the world. Water will be moved from the pumping plant through twin tunnels called the Tehachapi Discharge Lines to the top of the lift. From here, water will flow through four additional tunnels which are all linked by short connecting structures (Fig. 1). The tunnels are referred to as Tunnels 1, 2, 3, and Carley V. Porter Tunnel. HISTORY Selection of the final route of the Tehachapi Crossing was the result of comprehensive investigations beginning in 195 1. Numerous tunnel

Jan 1, 1970

By James R. Dunn

The purpose of this chapter is to review the uses of sand and gravel by the construction industry. The specific intention is to give tech¬nical people the general perspective and frame¬work which they need to help in making tech¬nical and business decisions. In the sand and gravel industry such decisions are based on an understanding of sociologic, economic, and technologic factors. In order to discuss the sand and gravel industry intelligently, it is necessary to define sand and gravel. "Sand" as most often used by industry is not sand in an engineering or geo¬logic sense but should be called "natural fine aggregate." The expression "fine aggregate" is preferable to "sand" because fine aggregate in¬cludes grain sizes which, according to engineer¬ing or geologic classifications, are defined as pebble or grit size. Natural fine aggregate is distinguished from manufactured fine aggregate in that the manufactured material is crushed and screened to produce the required sizes and natural fine aggregate is only screened. Coarse aggregate is generally defined as aggregate which will not pass a No. 4 or %o-in. sieve. Coarse aggregate may be natural (gravel) or manufactured (crushed stone, crushed gravel, slag, or coarse lightweight aggregate). Gravel is usually considered sufficiently crushed to qualify as manufactured coarse aggregate when two or more sides are broken. Sand and gravel (crushed or uncrushed) is used in asphaltic and portland cement concretes, is subbase for pavements, as fill where good drainage is needed (such as around structures), and for many other uses. About 96% of all he sand and gravel produced is used in construction.

Jan 1, 1975

By J. J. Bowman, E. H. Dix

A lack of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100" C. are too small to be of practical importance. Introduction The technical literature contains numerous papers describing die castings, their production, compositions and uses, but nearly all of these

Jan 1, 1935

By Guy Ruggles

IN this paper the authors aim to chronicle the experience and salient points brought out in changing flotation reagents at a concentrator which had probably been using a minimum amount of oil at a minimum cost per ton, to a more complicated system requiring a partial chemical control. The original oils were coal tar and pine oil. The new reagents are line, xanthate and pine oil. It was found that there were no insur-mountable difficulties and eventually the cost of the new reagents per ton of ore proved to be very little more than that of the old. LIME PLANT When the question of handling lime came up there were two propositions open: (1) to handle the lime dry; (2) to handle it wet in the form of an emulsion. Granting that a dry lime feeder would function properly, delivering lime uniformly, the chief objection was the dust that would be raised when these feeders were being charged or operated, as the only possible location was on a gallery beneath which men were working. With this objection the handling of lime as an emulsion seemed to he the better scheme. The lime plant which was first installed was for experimental work on one section. This was gradually changed and developed until it was of sufficient size to accommodate 20 sections. The various changes will not be discussed and the following description deals only with the fully developed plant. Crude as it is, and perhaps somewhat expensive to operate, the lime-handling plant has been quite successful. Much has been learned which will pave the way for a better installation in the future.

Jan 1, 1927

By Harry H. Power

The relative merits of air and natural gas as propulsive agents in pressure drive operations have been discussed for a number of years. When air or gas is introduced into the sand, various factors lead the operator to the selection of what he believes to be the proper propelling medium; but when the question of relative drive effect is raised, several physical and chemical premises must be taken into consideration in arriving at a conclusion as to the superiority of one medium over the other. Dow and Calkins1 and Beecher and Parkhurst2 have contributed fundamental experimental work on the effect of dissolved gas in lowering the viscosity and surface tension of crude oil. Herold; and Tickell' have indicated that whatever type of reservoir control obtains, gas plays other important parts in the movement of oil towards the well, namely: 1. The propulsive and expansive force of the gas. 2. The "Jamin effect," or resistance to the movement of oil in a porous media due to the formation of gas bubbles. When quantitative studies are made, parallel conditions must be selected whereby we may say definitely whether air is superior to gas as a driving medium, or vice versa. Examples of similar conditions are not easy to find in the field. However, in the laboratory we can make determinations which may lead to general conclusions when applied to the field. The experimental and research work described here was started at the laboratories of the University of California in January, 1927, and completed in private laboratories at Tulsa, Okla., in February, 1928. The apparatus used was designed especially for the work.

Jan 1, 1929

By J. H. M. Thomeer

A method is presented that provides a mathematical description of capillary pressure curves and, probably, of differences in pore geometry of samples. The technique is based on the observation that the location and shape of a capillary pressure curve reflect characteristics of the pore structure of the sample. INTRODUCTION It has been noted1-5 that the observed differences in shape and location of capillary pressure curves reflect some basic properties regarding the pore geometry of the samples. For example, according to basic concepts of capillarity, the following statements can be made regarding the location and shape of a capillary pressure curve.* The location of the curve with respect to the (Vb)pc and PC axes is a measure of the interconnected pore volume and of the cross-sectional area of the pore first entered by mercury, respectively. The shape of the curve depends on the interconnection of the pores and the sorting of the pore sizes. It has been the object of this study to use this information as a starting point in an attempt to find a unique mathematical description of the PC — (Vv)p, relations of different samples. It may be expected that parameters in such a relation can then be used to describe differences in pore geometry of these samples. For a practical description of the PC — (Vb)p, relation, however, it appears desirable to describe each curve (i.e., each sample) by a limited number of parameters so that the curves taken from all samples form a family, each member of which is uniquely determined by one single combination of values of all parameters.

By George Rice

A PROBLEM of possible subsidence of the surface from mining opera-tions, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitch-ing lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excava-tions. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter, and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1-12). The mining company had the right to remove the ore, the railroad assuming that the surface would be sup-ported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence.

Jan 1, 1934

By Allan Clark

(San Francisco Meeting, September, 1915) IT is nearly three years since the metallurgy of the Homestake ore was discussed with considerable thoroughness, in a paper' read before the Institution of Mining and Metallurgy. Certain changes have been made in this period which are perhaps of sufficient interest to justify a brief description, and it is chiefly with such details and miscellanies that this paper will deal. In the circumstances, a certain amount of repetition is inevitable, but matter treated of in the former paper will be referred to here only when it is necessary for the sake of coherency. For full descriptions of equipment and technique, the former paper should be consulted. The mineralized slates and schists which constitute the ore vary considerably in composition, but the unoxidized ore, perhaps constituting the major part of the reserves, contains either chlorite or hornblende (cummingtonite), with quartz, carbonates of lime, magnesia and iron, and arsenopyrite, pyrite, and pyrrhotite. Ferrous minerals predominate, and this fact has been an important factor in determining the metallurgical treatment. With one or two exceptions the minerals noted are of relatively high specific gravity, and the ore as a whole is exceptionally heavy, many determinations giving an average specific gravity of 3.00. This high specific gravity presents one decided advantage, when the' cost of treatment is compared with operations elsewhere, in that the ton, almost universally the basic unit, represents a volume probably less by 10 per cent. than that of many gold ores. On the other hand, this high gravity renders more difficult the discharge of pulp from mortars, its distribution on amalgam tables, and its transportation in launders.

Jan 7, 1915

By R. Hogg

INTRODUCTION As mineral particles are made smaller and smaller, it follows that their surfaces assume a greater and greater importance. In the extreme, the colloidal systems are characterized by the complete dominance of surface over bulk properties. Surface characteristics and properties will clearly influence any fine-particle processing operation. Comminution, for example, is a process of creating new surface. Agglomeration, on the other hand, may involve the reduction of surface area and the forces involved are generally surface forces. All mineral separations, solid-solid as well as solid-fluid, involve the treatment of two or more phases (solid plus liquid and/or gas). As the interfacial area increases, so will its effects on processing. Both physical and chemical separations are influenced by interfacial phenomena. Gravity separations are usually performed in a liquid phase and may be affected, for example, by the wetting characteristics of the solids. Flotation processes, of course, are based on the exploitation of differences in surface properties. Hydrometallurgical processing usually involves interfacial chemical reactions, e.g. leaching. The rates of such reactions depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. In characterizing a mineral surface, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface, which may depend on segregation of impurities within the solid and on adsorption from the external environment as well as on the bulk composition of the solid, will generally determine such

Jan 1, 1980

By S. H. Penn

Preliminary experimental evidence seems to preclude the use of unlubricated mechanical force drills on the moon. Measured values of the coefficients of friction and adhesion between metallic and nonmetal-lic solids have been shown to increase in an ultra-high vacuum environment. The paucity of real knowledge of the influence of a hard lunar vacuum upon interacting solid surfaces, relegates current proposals to sample the moon with a mechanical force drill, to the equivalent of wildcatting on earth. Within a few years, drilling will be attempted on the lunar surface with tools that have been designed with parameters that are normally considered for most conventional terrestrial drills. Lunar drills must be light in weight, portable, have reasonable penetration rates, low manpower requirements, etc. Although the initial equipment cost is expected to be high, this will probably not be a critical factor. Early lunar drilling will be limited to shallow holes with depths of 10 ft or less. The primary function of these holes will be to furnish samples of lunar surface materials but they may also be utilized for other purposes, such as geophysical experiments. Instruments may be installed in them capable of measuring thermal diffusivity, gamma radiation, etc. As sampling will be the primary objective of the earliest holes, sample contamination is a parameter that effectively excludes such otherwise promising techniques as explosive or plasma jet drilling. The most desirable method is probably some form of mechanical force drilling that has the capability of operating in the extreme lunar thermal environment (125° to 37S°K), high vacuum (10- l3 torr range), and low gravity.

Jan 1, 1968