Search Documents

By Willard R. Jillson

Within the last ten years Kentucky has become celebrated for its low-sulfur bituminous coals. Prior to this time, many investigators had discnvered the abundance of this coal but the fact was unknown to the general public until the last extension of Kentucky's mountain railroads' was completed. The coals of. Kentucky are, broadly, separated into two geographic units—the eastern and the western coal fields. On a basis of their sulfur content these coal fields fall into three units, which are indicated on the accompanying map, by numbers, 1, 2, and 3. The area marked 1, the very southeastern part of the state, shows the lowest sulfur, all coals being averaged. In this field the maximum is 1.04 per cent. and the minimum as low as 0.68 per cent.—both averages and not individual analyses, which would of course show much greater variation. Included in this group are the following counties: Lawrence, 0.87 per cent.; Martin, 0.75 per cent.; Johnson, 0.73 per cent.; Magoffin, 0.87 per cent.; Floyd, 0.88 per cent.; Pike, 0.68 per cent.; Knott, 1.04 per cent.; Perry, 0.77 per cent.; Letcher, 0.80 per cent.; Leslie, 0.70 per cent.; Harlan, 0.79 per cent.; Knox, 0.86 per cent.; and Bell, 0.92 per cent. The total average sulfur content for these thirteen counties is 0.82 per cent. Bordering the restricted low-sulfur field of eastern Kentucky is the No. 2 belt (slightly darker), 'which is commonly known as the western border of the eastern coal field. Here the maximum sulfur is 2.91 per cent. and the minimum 1.05 per cent. Again these are averages and not individual analyses. The counties in this group are: Greenup, 2.60 per • cent.; Boyd, 1.67 per cent.; Carter, 1.07 per cent.; Morgan, 1.40 per cent.; Wolfe, 1.83 per cent.; Lee, 2.93 per cent.; Breathitt, 1.85 per cent.; Owsley, 1.09 per cent.; Jackson, 1.06 per cent.; Rockcastle, 2.30 per cent.; Clay, 1.09 per cent.; Laurel, 1.08 per cent.; Pulaski, 2.24 per cent.; Whitley, 1.05 per cent.; McCreary, 1.50 per cent.; and Wayne. The sulfur percentage average for this area including fifteen important counties is 1.65 per cent. In the western Kentucky field, the great increase in the percentage of sulfur is at once apparent. Ohio County with 3.78 per cent. is the highest and Hancock with 2.87 per cent. is the lowest. The percentages by counties is as follows: Hancock, 2.87 per cent.; Henderson, 3.22 per cent.; McLean, 3.27 per cent.; Muhlenberg, 3.31 per cent.; Hopkins,

Jan 1, 1920

Manganese Resources in Relation to Domestic Consumption Discussion of paper by JOHN V. W. REYNDERS, presented at the Cleveland Meeting and issued, as Pamphlet No. 1656-C, with MINING AND METALLURGY, May, 1927. A. G. BETTS, Kinderhook, N. Y. (written discussion).-When a business concern hires an office boy, it takes on the first bright-appearing young chap to apply and pays him the prevailing rate of wages. One of the chief tasks the .office boy is supposed to be competent to perform, is to clean out the office. The manager of the business is highly competent in many lines, but for some reason lacks the ability to keep the office clean. To the steel man, it would seem that manganese is the office boy, and it is purchased just as found and offered to the purchasing agent. The steel mill is competent to perform many functions on a grand scale and with wonderful efficiency, but it is unable to make real steel. It is the function of the office boy, manganese, to do this. It is open to serious doubt if steel mill operators have ever taken seriously the metallurgy of the preparation of crude manganese. It has merely been found that some usable crude manganese may be obtained by running certain manganese ores through an iron furnace when not busy on anything else, or remote from iron ore, or with a lining that is about gone. It is, however, an entirely unwarranted assumption that the metallurgy of manganese has been worked out, or that the supplies of usable raw ore must be limited to materials of some specified analysis. There was a time when ores of copper, lead and zinc, for example, had to be rich and of specified analysis, to be usable, but the commercial raw materials of today bear little resemblance to such ores of the past. The discussions of manganese that I have seen are based on the assumption that the metallurgy of manganese is fully established and that the only usable manganese raw materials are of the kind used today. These discussions contain another error, not so much of statement, but of implication-that the tonnages of manganese materials in the United States are so much in this state and so much in that. When it requires a period of years and the expenditure of millions of dollars for a competent mining company to explore thoroughly a few acres of mining ground, is it not absurd to say that there are so many hundred tons of manganese ore in a certain state? This fact is not apt to be known fully in 10,000, years. I do not charge the mining engineers. who are on record, of making misstatements, because they merely say that so much

Jan 5, 1927

HAVING previously shown you how ores are found and mined, and also how they are prepared and disposed for smelting, and then how the blast furnaces and other furnaces are made for purging their earthiness, all this would be as nothing if I did not proceed to show you the method of smelting them. Therefore, in the present chapter I wish to show you how you must proceed in this very important operation, telling you all I have seen and also how much work with this kind of blast furnace I have done or directed. For this reason I tell you first to take by weight or measure the quantity of ore that you wish to smelt and, particularly if it is a kind that contains silver, break it into small pieces about the size of [52v] beans. If the ore had previously needed evaporation by fire or cleaning by washing, you will have had this done well and have had it properly prepared by a master sorter or others. A layer of this is arranged on a bed of planks, bricks, or flat stones in front of the blast furnace and its companion is placed on top, then a quarter part of galena or a third if you can obtain it. Then an equal part of crushed iron slag or slag from the same or different ore is added. These materials are spread in layers one above the other. When the blast furnace has been constructed as taught above, correct in all its parts, and is full of well-kindled burning charcoal, then fill it up with charcoal and admit water to the bellows machine. When you see that it is well kindled again from this wind and that the flames begin to come out forcefully on top, work it down with a little rake and fill it up again. Then the pannier is filled with new charcoal, the blast furnace heaped full, and another basketful of the said composition of ore is also put on top. Proceed in this way, continually adding charcoal and ore as long as you have any, or as long as you wish to keep up the work, maintaining the blast furnace always full, or continuing in this way until the bottom of the blast furnace is filled with melted materials. Decide this by judgment, or by seeing through the mouth of the tuyère where the wind of the bellows enters that they are level with this. Then with an iron tool open the hole that was left as an outlet in front of the blast furnace and allow all the metal with its slag to run out. These two things, flowing through the chan-

Jan 1, 1942

By Robert M. Dreyer

Diamond is the hardest known material. The diamond industry is separated into two major segments: (1) industrial and (2) gem. The major industrial use of diamonds is as a high-grade abrasive in a wide variety of applications for which no effective low-cost substitute is available. Table 15.4C.1 gives data on diamond production and on United States diamond imports. In both gem and industrial diamond production, but especially in the case of gems, the quantity of stones produced is not directly correlated to value, for the determination of value is markedly affected by quality. South Africa long has been the world leader in gem diamond production with an estimated production in 1968 (including South-West Africa) of about 4 million carats, equal to 43% of world production. During the past decade there has been a marked rise in gem diamond production in the USSR, so that nation is now the second-ranking world producer, with Angola (Portuguese West Africa) third. In natural industrial diamonds, the major production comes from Congo-Kinshasa (former Belgian Congo) which had a production of 15 million carats in 1968, equal to 47% of world production. In the past six years, there has been a remarkable increase of industrial diamond production in the USSR, which now ranks second with a production of 6 million carats, equal to about one-fifth of world production. South Africa now ranks third followed by Congo-Brazzaville and Ghana. No natural diamonds are produced in the United States. Since the discovery of an economical method for synthesizing small diamonds, there has been a rapid increase in synthetic production from 4 million carats in 1962 (1 carat equals 200 mg) to 11.5 million carats in 1968. Table 15.4C.1 gives the gradually increasing imports of industrial diamonds and indicates a relatively stable price. In 1968, the imports of industrial diamonds were 13.5 million carats with a value of $59.2 million. Table 15.4C.2 shows the rapidly increasing imports of cut and uncut gem diamonds into the United States. In 1968 the United States imported 2.5 million carats of uncut stones with a value of $166 million and 1.5 million carats of cut stones with a value of $175 million. Diamond marketing is dominated by DeBeers Consolidated Mines, Ltd., which, through subsidiaries, controls many of the major African diamond deposits. More important economically, however, through its Central Selling Organization, DeBeers markets 86% of the non-Communist world's natural diamonds, including most of those derived from deposits outside of corporate control. In 1967 the mines owned by DeBeers produced nearly 8 million carats, and the Central Selling Organization sold over $600 million in gem and industrial diamonds. The dominance of diamond sales by

Jan 1, 1976

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,',2'" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,' measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"' suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955

By A. W. Fahrenwald

CELL depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence-i.e., the depth in the pulp at which the impeller is required to produce aeration. THE FLOTATION MACHINE A COMPRESSOR A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure[t] (14.7 lb. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 lb. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 lb. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 [-] 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 [=] 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the finer, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. THE FLOTATION MACHINE AS A PUMP Since, in impeller machines that rely upon their own operation to produce aeration, pulp passes through the im-

Jan 1, 1946

By Richard M. Foose

FIVE miles southwest of Mt. Holly Springs, Cumberland County, Pennsylvania, the Philadelphia Clay Co. has been mining and milling a white clay since 1896; for use in white cement, as a filler in rubber, pigment and paper, in the manufacture of insecticides, and for other minor purposes. Until late in 1942, when the mine was abandoned because of labor shortage, combined underground mining and surface stripping produced approximately 30,000 tons of clay a year, of which 10,000 tons were refined in the mill. GEOLOGY Lower Cambrian Antietam quartzite and the Montalto quartzite, stratigraphically older, trend N.55°E. and make a sharp 1600-ft. anticlinal ridge of the South Mountains. The Tomstown dolomite overlies the Antietam quartzite on the southeast flank of the anticline, which is displaced near its crest by a steeply dipping oblique fault. Erosion of the less resistant Tomstown formation has resulted in a narrow valley at an elevation of 700 ft. Directly on top of the Antietam quartzite and at the base of the Tomstown formation is a zone of sandy white clay, lenticular along the strike of the formations, ranging in thickness from 10 to 300 ft. within a mile. All of the formations dip steeply to the southeast, from 65° to vertical. The clay crops out at an elevation of about 1000 feet. ORIGIN AND CHARACTER The uppermost part of the Antietam formation is sericitic and schistose at many places, and at all these places weathering is in an advanced stage. The clay is the residual product of weathering of this sericitic quartzite or sandy schist. The crude clay has the physical aspect of a sandy kaolin, but there are large areas in the clay formation that are low in free silica, and commonly the 30 ft. adjacent to the Antietam quartzite is notably free of silica. The overlying Tomstown dolomite has been weathered almost completely to a mixed yellow and brown clay, which carries a zone of nodular and chunky limonite and manganese ore, 4 to 12 ft. thick, about l00 ft. from the contact with the white clay. In mining, this zone is an important "marker," indicating where the white clay may be expected in an advancing tunnel. The contact of the white clay formation with the yellow and brown clay of the Tomstown formation is relatively sharp, although the line of contact is irregular and therefore responsible for the lenticular character of the white clay formation. Following is an analysis of the refined clay containing less than one per cent of moisture when dried at 212°F.: Si02, 67.05 per cent; A1203, 22.27; Fe203, 0.40; CaO, 0.00; Ti02, 1.05; MgO, 0.52; Na20, 0.04; K20, 0.88; ignition loss, 7.65; total, 99.86.

Jan 1, 1944

By Robert L. Hoss

The application of Muskat's differential equations for predicting the performance of a solution gas-drive reservoir to the Fullerton field indicates that a recovery may be expected of 14,030 bbl per acre under primary depletion, and 15,910 and I7,190 bbl per acre, respectively, under the two pressure-maintenance programs analyzed. In this analysis it is assumed that fluid properties are the same throughout the reservoir, that the core data used are typical of the Clear Fork limestone in the locality, and that injected gas is completely diffused through the pay zones. The economic study of the three recovery programs considered indicates that the one in which 60 pct of the produced gas is returned to the formation is the most profitable. Introduction The purpose of this paper is to consider the effect of pressure maintenance by gas injection on the ultimate recovery of oil from a solution gas-drive reservoir. This prediction of reservoir behavior is the result of calculations based on the equations presented by M. Muskat in the Journal of Applied Physics, March 1945. Reservoir The reservoir analyzed is the Fullerton field in Andrews County, West Texas. It is situated on a broad anticlinal structure with approximately 330 ft of closure, and extends approximately eight miles north and south and five miles east and west. The areal extent is taken as 16,642 acres. The producing horizon is the Lower Clear Fork limestone of Permian age, occurring at depths from 6650 to 7350 ft. It is divided into four zones. For the purposes of this study, the fluid characteristics in all zones are assumed to be the same. Therefore an equivalent zone is assumed of thickness equal to the sum of the thicknesses of the four zones, or an average of 216 ft. The reservoir contains 3,586,991 acre feet of producing limestone, with an initial volume of stock tank oil in place of 918,-403,100 bbl. The average connate water saturation is 24.0 pct. The permeability ranges from 6.7 md. to 12.6 md., and the porosity ranges from 7.7 pct to 11.4 pct, except for occasional cavernous streaks. Based on these values, the limestone may be considered intergranu1ar.l Production histories and material-balance studies have indicated that the driving mechanism is solution gas. Water levels have been established. Theory It is possible to express mathematically the change in residual oil saturation with pressure decline in a solution gas-drive reservoir as being equal to the change in the physical properties of the fluids present in the reservoir as this pressure decline occurs. Essentially these equations, in differential form as presented by M. Muskat,2 express quantitatively the instantaneous net effect

Jan 1, 1948

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By W. T. Bishop

For many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. History The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and 'Oat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree—rosin and turpentine— but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores " industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.' In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1947

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

By Fred C. Bond

AN improved method of measuring the surface area of a comminution product down to any desired particle size has been developed. The method is largely graphical, and requires relatively little calculation. It can be used with materials containing large amounts of clay, or excess fines of any kind. The surface area S is expressed in terms of square meters per 100 c.c. of solids. This expression is based upon volume rather than weight, and is considered to be more suitable for crushing and grinding problems, where the machines ordinarily are operated under constant volume conditions. It has the advantage that surface areas of different materials can be compared directly, even though their specific gravities may be unknown. The "specific surface" of a material, or the number of square centimeters of surface area per gram, is equal to 100S divided by the specific gravity. Particle diameters are expressed in microns, K being the diameter of the largest particle present and L the grind limit, or lower size limit of the particles formed directly by grinding. The value of K does not always coincide exactly with the diameters of the largest particles retained on the coarsest testing sieve, since the largest particles formed in crushing and grinding are often slabby, or have other irregular shapes. L has been chosen as 0.700 microns, or number 27.5 in the size number series, for reasons to be explained later. S is the total surface area of all particles larger than L microns in diameter. When a homogeneous comminution product is separated into fractions whose diameters bear a constant geometrical relationship p to each other, and the log per cent weight retained upon each size and passing the next larger size is plotted against the log diameter, a straight line results, which is called the distribution line, and which has a slope in called the distribution modulus. The distribution line can be extended to any desired limiting size, and the total surface area of all particles larger than that size can be calculated. The equation of the distributi0n line is [w = Cx" [I]] where w is the per cent weight retained on each successive sieve; x is the particle diameter; and C is the per cent weight retained on an opening of unit diameter.2 Theoretically, the distribution line can be extended to include infinitely small particles. When it is so extended, and the assumption is made that no fine particles are present other than those accounted for by the equation; the log per cent cumulative weight passing any series of sizes, plotted against the log diameter passed, will result in a straight line lying parallel to and above the plotted distribution line.

Jan 1, 1941

By A. W. Fahrenwald

Cell depth has been for many years a controversial question in a flotation-machine performance. In the impeller type of machine, we are really talking about impeller submergence—i.e., the depth in the pulp at which the impeller is required to produce aeration. The Flotation Machine a Compressor A flotation machine can be considered as an air compressor or blower in which the aeration mechanism takes in air under atmospheric pressure† (14.7 Ib. per sq. in.) and blows it into the pulp (the pulp being the receiver) against a head of 14.7 plus cell depth in feet times 0.4333 lb. per sq. inch. In commercial machines the impeller is submerged in the pulp to depths ranging from about 2 ft. in the smaller machines to as much as 5 ft. in some of the larger ones. In the 2-ft. cell, the hydrostatic head on the impeller is (2 X 1.25 =) 2.50 ft. (assuming a pulp density of 1.25), equal to (2.50 X 0.4333 =) 1.078 Ib. per sq. in. For the 5-ft. cell, the hydrostatic head against which the impeller must make air is (5 X 1.25 X 0.4333 =) 2.708 Ib. per sq. inch. In the small 2-ft. machine, the volume reduction is (1.078 ÷ 0.147 + 0.01078 =) 6.85 per cent and in the large, 5-ft. machine, the volume reduction is (2.708 0.147 + 0.02708 =) 15.5 per cent. It is obvious that for unit volume of free air intake the larger machine receives a lesser (8.65 per cent less) volume of aeration* than the smaller machine. The bubbles in escaping from the pulp expand and are greater in volume at the surface than at the moment of their formation in the pulp; 7.33 and 18.4 per cent larger, respectively, in the small and large machines. Just how this situation affects flotation is not known. It is interesting to note, however, that the bubbles are smaller in the zone of the coarsest particles and largest in the upper zones of the her, more easily suspended mineral particles. It would seem that the relationship might be reversed advantageously. The deep cell is at a greater disadvantage in this respect than the shallow cell. Nothing, however, presumably can be done about this situation. The shallow cell is a partial corrective. Not only does the compression ratio of aeration increase with impeller submergence but the hydrostatic head against which the impeller must operate also increases. The Flotation Machine as a Pump Since, in impeller machines that rely upon their own operation to produce aeration, pulp Passes through the im-

Jan 1, 1947

Prospectors were digging silver in the Ray mine area in 1873, and by 1880 high-grade copper ore was feeding a 30-ton copper furnace. In 1910, D. C. Jackling and his associates organized the Ray Consolidated Copper Company, known in mining circles as Ray Con, to exploit the Ray orebody. For 50 years, all mining was underground and the Ray mine was known the world over for innovations in mining methods. It was the first to mine important tonnage (8,000 tpd) by block caving methods. The mill at Hayden, 26 miles (41.6 km) from the mine, kept pace with the new mining methods developed at Ray and in the early 1920's flotation replaced gravity concentration by the vanner machines. First mining by open pit methods began in 1950 and in January 1955 all underground mining was discontinued. The new primary crushing plant, installed in early 1967, featured design simplicity with a low capital cost. The 54 in. gyratory crusher was installed within a total height of 6 1 ft (18.65 m) from the truck dump road bed to the floor beneath the feeder-conveyor under the surge pocket. The crusher is fed by 120-ton trucks dumping from one side only into a 200-ton hopper equipped with a horizontal splitter bar to protect the crusher spider. The crushed ore pocket, of 120 -ton live capacity underneath the crusher, discharges to a 0 to 200 fpm (61.2 mpm), variable-speed, 72 in. by 80 ft long (1.83 m by 24.4 m) sloped belt feeder, probably a first in the industry. Wood-picking stations are provided on either side of the belt so that old mine timbers and tramp iron can be removed from the crushed ore and the wood can be dropped into Dempster containers located below the belt. Counter-weighted finger gates control the bed depth on the belt at 14 in. (356 mm) and a low- level radiation unit automatically maintains a minimum of a 3 ft bed (900 mm) of material on the belt directly under the surge pocket. The conveyor is skirted for its full length and is approximately 60 in. (1.52 m) wide inside its metal skirt liners. Ten impact idlers at 12 in. (305 mm) spacing are provided under the loading pocket and remaining idlers are spaced at 18 in. (457 mm). The belt is 1 ¼ in. (31. 8 mm) thick; and, while it has occasionally been damaged by tramp material, belt life averages 11 million tons. When the belt is changed, the coiled new belt is lowered into position onto one of two belt stands mounted over the feeder, the old belt is cut, and one end is attached temporarily to the new belt. The other end of

Jan 1, 1978

By J. L. Snoek

[ ] DISCUSSION J. L, SNOEK*-Stress-induced preferential diffusion in cubic body centered metals in the annealed state provides us with a powerful tool for determining the mobility of interstitially solved atoms as well as their location in the lattice and the exact nature of the distortion brought about in the lattice by their presence. Calculations given by D. Polder31 show that the distortion of the lattice, besides being proportional to the applied stress P, is also proportional to [VC, RT + xVCo] where T, V and Co are the temperature, molar volume of the solvent and molar concentration of the solute respectively and x is a constant describing the mutual interaction energy of the dissolved particles. This calculation obviously is no longer valid if x is negative and the abso¬lute value of xVCo surpasses that of RT. The lattice may then be expected to become tetragonal spontaneously. Such a spontaneous tetragonality seems to have been observed by W. Klemm and L, Grimm for the case of oxygen solved in vanadium.32 Measurements of the internal friction in cold worked iron containing carbon or nitrogen should provide us with information on the mobility as well as the preferential location of these particles in the iron lattice in the cold worked state. The work by T'ing-Sui Kê is a valuable contribution to this problem, The data obtained by T'ing Sui Kê and myself on cold worked samples of iron seem to indicate that carbon and nitrogen in these samples are found either in the normal (1/2 , 0, 0) interstices or in a new preferential position created by the cold working. The latter positions in my opinion can hardly by anything else but the edges of the dislocations. The observed larger distances of diffusion might be explained by assuming that the carbon atoms when freed from a certain dislocation by thermal agitation must diffuse over several atom distances before being caught in another dislocation. The theory however needs working out and no doubt will be much more complicated than the one valid for the annealed state. T'ING-SUI KÊ (author's reply)-It is highly encouraging to read the written discussion given by Dr, Snoek who initiated the theory of stress-induced preferential diffusion in cubic body centered metals in the annealed state, Since the presentation of this paper, the author has done more experimental work on this subject which seems to be able to settle several of the points raised by Dr. Snoek. It has been found that such stress-induced preferential diffusion occurs also in the solid solutions of carbon,33 oxygen,34 and nitrogen35 in tantalum which has a body centered cubic structure. Analysis of the shape of the observed internal friction. peaks indicates that the inter-

Jan 1, 1948

By W. T. Bishop

FOR many years pine oil has been used extensively as a frother for the flotation of minerals, particularly sulphides, yet the published information available to the average user on its composition, chemical and physical properties, has been rather meager. It is the purpose of this paper to discuss these points and their relationship to the frothing properties of pine oil used in flotation processes. Pine oil, as the name implies, is a liquid obtained from the processing of wood of the longleaf and other southern pines. It is a complex mixture of naturally occurring terpene derivatives, primarily alcohols, and a smaller amount of terpenes, which has found many uses in various industries. Its use as a frother in flotation processes was the first large-scale application in industry and today the mining industry still consumes large quantities of pine oil but the textile and disinfectant industries consume comparable volumes. Much is used in soap manufacture and laundry operations. The surface-active properties of pine oil are in a large degree responsible for this versatility. HISTORY The name "Naval Stores" goes back to the days when pine tar and pitch were used to caulk leaky ships and coat their ropes and rigging. Today this term is still used to include not only the oleoresinous products of the pine tree-rosin and turpentine-but other products such as pine oil, pine tar, and the many terpene and resinous compounds obtained by extracting the pine wood or tapping the tree. That part of the industry known as "wood naval stores" dates from about the beginning of this century and today produces a large part of the country's rosin and turpentine by processing pine wood. In addition, all of our natural pine oil is, supplied by the wood naval stores industry, as tapping of the live tree gives only rosin and turpentine. This latter phase is known as the "gum naval stores" industry. The first successful commercial operation of the steam and solvent process of the wood naval stores in industry was carried out by Yaryan at Cadillac, Mich., in 1909.1 This operation did not prove profitable, so Yaryan went south to utilize the longleaf pine, and built a plant at Gulfport, Miss.2 Soon after, another plant was built at Brunswick, Ga., which is still in operation, and in 1914 was reported to have processed about 500 tons of wood per day.1 In 1921 Hercules Powder Co. acquired the Yaryan interests, at which time the production of pine oil was only 3 to 5 million pounds per year and flotation was the largest customer. As time went on, technological advances were made, other companies entered the field, and the production of pine oil increased many fold. The growth of the industry was especially marked during the past 10 years, and in

Jan 1, 1946

By Martin Coryell, Eckley Coxe, R. P. Rothwell

WILKES-BARRE, PA., April, 1871. THE great development of the mines and metallurgical works of this country during the last few years, accompanied as it has been by the investment of enor¬mous sums of money in purchasing lands, and in the erection of improvements, requires that advantage should be taken of the accumulated knowledge of engi¬neers, superintendents, and others, in mastering the problems which are con¬stantly presenting themselves for our action. Among those may be mentioned the consideration of more economical systems of mining in our coal and metal¬liferous mines, improved methods of transportation above and below ground, unwatering and ventilating mines, the mechanical preparation of coal and other minerals, the various metallurgical processes, and, in fact, every question tending to the attainment of two great objects 1st. The more economical production of the useful minerals and metals. 2d. The greater safety and welfare of those employed in these industries. In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed as the free interchange of experience among those actually engaged in these industries, and this object has been accomplished, mainly, through the medium of institutes, associations or societies, composed of those engaged in these occupations, and by the- periodical publication of essays or papers, communicated to such societies by their members. It must be evident to all practical men that the interchange of the varied experience of those engaged in such occupations in this country could not fail to advance very materially the desired objects; it is, therefore, proposed to establish an American Institute of Mining Engineers, which will hold its meetings periodically in the great mining and metallurgical centres, where works of interest, such as mines, machine shops, furnaces, and other metallurgical works, can be inspected, and the members exchange their views, and consult for mutual advantage upon the difficulties encountered by each; these transactions or proceedings, when published, would form a most valuable and greatly-needed addition to our professional literature. It is proposed that a meeting of those sympathizing with the object above men¬tioned shall be called for the purpose of organizing such an association, the place and time of meeting being Wilkes-Barre, Pa., and the month of April or May. Communications indicating the opinion and wishes of all, both as to these points, and also as to the organization and objects of the Institute, will be gladly received by any of the undersigned, and a notice of the date of meeting, which will be arranged to suit the greater number, will be duly communicated. Any

Jan 1, 1873

By Warren E. Wilson

The transportation of solids in pipe lines is a matter of deep concern in many fields of engineering. Much experimental and theoretical work has been done in an effort to devise means of designing pipe lines that will satisfactorily transport given solid loads, but there remain many unanswered questions in this field. The present discussion will be confined to a rather narrow portion of this field and will endeavor to point out certain factors that may well be considered when comparing the relative economy of various installations. The data have been presented previously but a new interpretation was prompted by a suggestion in a paper by Professor O'Brien,1 of the University of California, that the friction work per pound of dry material should be considered in determining the relative efficiency of various installations. This method of considering relative economy in various pipe lines leads to some rather unexpected conclusions, especially with reference to the economy of large pipe sizes. A previous suggestion by the writer3 concerning the economy of a rather peculiar type of installation is strengthened. It is not believed that the considerations set forth herein apply directly in the case of dredge lines, where economy is largely a matter of a high rate of pumping in order to reduce the unit overhead charge. However, it is believed that some value may be gained from these considerations in cases involving the disposal of a fixed amount of solids per unit time with a minimum expenditure of energy and at a low cost for replacement of worn pipes. Such situations are not uncommon in the disposal of mill tailings and the disposal of solids deposited from irrigation waters. It was found that data leading to general conclusions for various pipe sizes were not available but certain definite trends are indicated and methods of analyzing available data are presented in the hope that they may be of assistance in preparing engineering estimates on designs of pipe lines of the type described above. Energy Requirements Carrying out the idea contained in ' Professor O'Brien's paper concerning the method of computing energy required to transport solids, the following analysis leads to some rather interesting conclusions. Let us represent: Solids load in term of mass per unit time by W Ratio of mass of suspended solids to total mass of mixture flowing by p Volume rate of flow of mixture by Q Length of pipe by L slope of energy grade line by s Mass per unit volume of solids by m. Mass Per unit volume of liquid by mi Mass per unit volume of mixture by mm We then have as an expression for the solids load: W = pQmm The work done per unit mass, P, on the mixture to move it along the pipe the

Jan 1, 1948

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946