Search Documents

By H. C. Chang, N. J. Grant

REEP studies and measurements in most in-V> stances are based on a relatively gross gage length. Even in some recent theoretical studies on the mechanism of creep, changes were followed by means of X-rays and metallography without regard for the behavior of the individual grains and grain boundaries.'" Analytical studies of creep have frequently indicated that more than one competing process is operative and that the ultimate creep performance depends on the effects of temperature, time, and strain rate as well as grain size.'-" he grains and grain boundaries are known to respond differently to these variables but the extent of the response is still little known, especially in poly-crystalline materials where the relative orientations of grains and grain boundaries are important. This paper reports some experimental observations of the behavior of the grain boundaries and their effect on the deformation in the grains. High purity aluminum was used to avoid complications of aging reactions, second phase, inclusions, etc. Experimental Procedure A small vertical nichrome wound furnace was built to permit direct loading on the test specimen. This furnace is capable of operating up to about 1300°F with reasonable temperature distribution. A ground rectangular quartz window, 1.25x0.5 in., is imbedded in the external stainless steel tube to permit observations of the creep process with a microscope. An argon atmosphere ,was provided to prevent oxidation. The quartz window caused a temperature gradient between the back and front surfaces of the specimen of 15" at 700°F. The temperature gradient could be cut down to 3°F along the length of the specimen by adjusting shunts across the furnace windings. An ordinary metallurgical microscope with a working distance of 14 mm was rebuilt so that it could be moved in three mutual perpendicular directions. Visual examination could be made with either a 30X eyepiece or a 15X filar eyepiece. Using an objective of focal length 24.3 mm and a numerical aperture 0.20 a total magnification of 120X or 240X could be obtained. High purity aluminum rated at 99.995 pct was supplied by the Aluminum Co. of America as % in. then the gage portion was further machined to 3/16 in. diam. The ends were Y4 in. diam and threaded to fit available specimen holders. Two opposite flat surfaces of the gage portion were obtained by milling, giving final dimensions of the gage portion of 3/4x3/16x3/32 in. Machined specimens were first electropolished in Jacquet's solution.' Reference marks were produced by pressing a thin sewing needle into the surface of the specimen. The specimen was then annealed at 900°F for 24 hr and at 1150°F for 12 hr. Typical macrostructures of specimens treated in this manner are shown in Fig. 1. The range of the grain size was 1 to 5.5 mm (see Fig. l), but most of the grains were of 2.5 mm and went through the whole thickness of the specimen. The specimen was re-electropolished and etched electrolytically to reveal the grain boundaries. In order to reveal the orientation difference of the grains, etch pits were produced on the surface of the grains by etching in a mixture of hydrochloric and nitric acids (HC1, 45 pct; HNO,, 10 pct; H,O, 45 , by volume). The specimens were very carefully put into the holders and furnace; yet even with this care, fine slip lines were developed on the specimen surface.

Jan 1, 1953

By F. P. Nichols, F. A. Renninger

At one time, mineral aggregates were considered physically and chemically inert substances whose junction was that of an inex-pensive, easily obtainable source of bulk. This philosophy applied regardless of the use to which the aggregate was put. Research approaches dealing only with such gross physical properties as hardness, toughness, impact resistance, etc., dominated the early growth years of the industry and influenced specifications to a large extent. The accelerated pace of highway construction, which began toward the end of the depression years, focused attention on the need for extensive aggregate research. The realization in the early 1940's that aggregates interacted chemically as well as physically with their environment provided the stimulus necessary to translate the drab, systematic aggregate technology of the early 20th century into the changing, dynamic, challenging field it is today. Current research problems are discussed in detail. These efforts being pursued by contract research organizations, universities, governmental agencies, and industry transcend many fields. The mineral aggregate industry is the world's largest mining and processing endeavor, yet it is graced with little of the romance or public awareness that accompanies mention of gold, silver, iron, copper, uranium, or aluminum mining efforts. Much of this reaction is undoubtedly due to the fact that the uses to which crushed stone and sand and gravel are normally put are not fully recognized or appreciated by the general public. Almost 2 billion tons of mineral aggregates are quarried or mined, processed, and sold yearly in the United States alone.= The largest uses to which this vast tonnage is subjected are as ingredients of portland-cement concrete, bituminous concrete, and dense-graded aggregate-base course mixtures in the highway and building construction fields, two industries closely related to the expenditure of public funds. It is for these uses, partially in justification for the expenditures of vast sums of public funds, that mineral aggregate research truly finds its emphasis. The research efforts expended relative to the highway and building construction uses to which mineral aggregates are subjected are those of primary concern to the industry. These efforts, while of direct consequence to the industry due to the volume market represented, are of interest as well to public agencies, universities, and contract research firms. All actively conduct research, exchange information, and make contributions to the overall knowledge relative to aggregate usage and limitations. The research efforts of the mineral aggregate industry is the subject to be discussed throughout this paper. It covers all aspects of highway and building design, construction, and technology. The effects of research pertaining to quarrying and mining methods, blasting and processing techniques, storage and handling facilities, and equipment employment and development have left their mark on the crushed stone and sand and gravel industries. Such specialized efforts have resulted in dramatically increased production rates which in turn have served to keep costs, and hence prices, down. Despite the many inflationary pressures over the years, the cost of a ton of aggregate today is little more than it was 25 or 30 years ago. Mention is made of these efforts simply to emphasize the diversity of research in the mineral aggregate field. The remainder of this paper focuses on the complexity of what might be termed "product knowledge" research.

Jan 1, 1971

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By Castle. J. E., J. L. Gillson

In this chapter there is a wide difference in the meaning of some words used for rock and mineral names as defined by scientists and tabulated in the "Glossary of Geology and Related Sciences," published in 1957 by the American Geological Institute, and the meaning as used by the commercial producers of feldspar. It is necessary, therefore, to define these terms giving both the "scientific" and the "practical" definitions. There is no ambiguity about the name feldspar itself. This is a general term for a group of related minerals which are silicates of aluminum, combined with sodium, potassium and calcium. The feldspars are the most abundant minerals of the igneous rocks, and since these rocks make up the largest proportion of the earth's crust by volume (although not of the actual surface area of the continental land masses) the feldspars are the most abundant minerals of all. The igneous rocks themselves are classified on the basis of the variety of the feldspar present. The potash feldspars, which are called orthoclase and microcline, are the dominant minerals of the granites and syenites, and of their fine grained equivalents, the rhyolites and trachites. The plagioclase feldspars form an isomorphic series, of which the sodic endmember is called albite, and the lime endmember, anorthite. The members near the sodic end, albite, oligoclase and andesine are the characteristic feldspars of the granodiorites and diorites, and of their fine grained equivalents, the dacites, and andesites. These feldspars-orthoclase, microcline, albite oligoclase and andesine-are the feldspars used commercially. Labradorite, a member of the plagioclase group, in which the lime exceeds the soda in the chemical composition, is the common feldspar of the gabbros, anorthosites, norites, basalts and other so-called "basic" rocks. Although some attempts have been made to use labradorite as a commercial feldspar, none is now used except as an ornamental stone. The mineral anorthite is very rare. Since the feldspar in most of the common igneous rocks is relatively fine grained, and mixed intimately with other minerals, from which it can be separated cleanly only with difficulty, most masses of the common rocks cannot be used as sources for the feldspar contained in them. It is only the rarer types of rocks in which the feldspar is very coarse-grained, or ones containing very little of the iron-bearing minerals which are objectionable impurities in commercial feldspar, that are quarried to yield an acceptable product. The most widespread type of such a rock from which commercial feldspar can be produced, is that called "pegmatite." These rocks are dikes and bodies of irregular shape and of a size measured in feet or yards in most cases, rather than in miles. They are more commonly associated with granites, rather than with other coarse-grained igneous rocks. Many of them contain crystals of various minerals, including the feldspars, that are much larger than are found in the host rock, the granite, and in many there are large masses of feldspar that are sufficiently free from iron-bearing silicates so that products acceptable to the ceramic industry can be produced, in some cases simply by hand sorting. Most of this feldspar in pegmatites, however, does contain intergrown quartz up to 25 pct. Pegmatites are so important, not only as commercial sources of feldspar, but also of other minerals which are produced com-

Jan 1, 1960

By A. W. Bethune, L. M. Pidgeon

The equilibrium vapor pressure of zinc has been determined over the systems: ZnS(s) + Fe(s) = FeS(s) + Zn (vapor) and ZnS(s) + 2Cu(s) = Cu2S(s) + Zn (vapor) by reacting the components in an evacuated tube containing a thin copper fiber, and allowing equilibrium to be established with respect to the brass formed and the zinc in the vapor phase. The composition of the brass formed was determined and equilibrium vapor pressure values obtained from existing data. Between 850' and 1000°C, values for the first reaction ranged from 8 to 58 mm Hg; for the second reaction from 1.8 to 22 mm Hg. THE direct reduction of metallic sulphides may be indicated by an equation of the form MS + X = XS + M [1] where X is some suitable reducing agent. In the case where M is a metal of relatively high volatility, the use of vacuum will displace the equilibrium to the right at comparatively low temperatures in the face of the usually unfavorable thermochemistry. For this technique to be feasible, MS, X, and XS, must of course be nonvolatile compared to M. In this regard, zinc becomes an obvious metal both from the point of view of its volatility and the fact that most commercial ore deposits of this metal occur as the sulphide, and its direct reduction would avoid the expensive roasting process necessary prior to present day reduction methods. Two reducing agents are of interest, namely copper and iron, with the former having the added attraction of being relatively easily regenerated by oxidation in the copper converter. The possibility of these reactions has been considered before. Imbert1 patented a process whereby zinc sulphide was reduced by either copper or iron. The process as described took place at atmospheric pressure and, at the high temperatures required, the system was molten, resulting in the formation of a matte with the consequent reduction in the activities of the reactants. Peterson2 did further experimental work on these reactions and, although promising results were obtained on a small scale, attempts to increase the size of the furnace led to excessive "blue powder" formation. The early workers failed to realize the large reduction in temperature afforded by the use of vacuum and its desirable results. More recently, the direct reduction of zinc sulphide by iron has been the subject of a thermody-namic investigation by Kelley,3 and Gross and War-rington' have studied the kinetics of the reaction in the temperature range 900" to 1000°C, their experiments being conducted using vacuum and indicating that the reaction would proceed practically to completion in 1 to 3 hr, depending on the temperature. A qualitative examination of the system ZnS-Cu carried out at this University indicated that 98 pct of the theoretical zinc in the charge could be recovered in 1 hr at 1000°C when operating under reduced pressure. The purpose of this research program was to study the equilibrium of the two reactions. During the investigation, reference to the experimental work of Schenk5 was found but, due to lack of detail in the report, it was felt that it would be desirable to continue the equilibrium measurements. Selection of Method The measurement of vapor pressure of metals presents obvious problems resulting from the high temperatures which must be employed. In the present case, the production of the "reaction pressure" introduces a further difficulty since a chemical reaction must proceed before any metal vapor pressure is produced, resulting in depletion of the re-

Jan 1, 1954

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

By C. G. Dunn, F. W. Daniels

IN recent publications1-5 the existence and behavior of subgrain boundaries in high-purity metals has been clearly brought to light. Lacombe and Beaujardl by means of special etching methods disclosed in polycrystalline sheets of aluminum the existence of substructures differing in orientation by small amounts (about 1/4"). Boundaries of these structures at relatively high temperatures had the remarkable property' of moving about while the ordinary boundaries remained stationary. Cahn2 also observed substructures in bent and annealed single crystals of aluminum, zinc, magnesium, and rock salt. The position of subboundaries could be explained in terms of a dislocation mechanism of polygonization in which dislocations move into lines at right angles to the bent glide planes thereby relieving elastic stresses in these planes. Guinier and Tennevin8,6 disclosed the further interesting feature that polygonized structures coarsened significantly upon prolonged annealing. Somewhat similar subgrain phenomena have been observed in silicon iron of commercial purity. Although some evidence for the development of macro-mosaic structures in silicon iron already has been reported by one of the authors6,7 under the phenom-enological term "crystal recovery," much better evidence recently has been obtained due to improved etching techniques. In addition, phenomena regarding structural changes have been uncovered. The present investigation is divided into three parts: (1) The phenomenon of Laue spot sharpening on annealing cold-rolled crystals, (2) the phenomena of polygonization and subgrain coarsening The material used in the present investigation was high-grade commercial silicon iron sheet of nominal composition, 3.3 pct Si, 0.004 C, 0.011 P, 0.010 S, 0.04 Mn, 0.01 Al, 0.04 Cu, 0.01 Sn. Large single crystals of this material Were prepared for cold-rolling or bending as scheduled. Cold-rolling of 12 pct was carried out on a laboratory 8-in, diam rolling mill. The bending deformations were performed by pressing the crystals between a solid Fig. 2—lllustrative foue patterns to show Laue spot sharpening. a (Left)—Specimen as cold rolled, b (right)—After 48 hr at 1400°C. round bar and a mating half cylinder, both heavily greased. Individual specimens were cut from the deformed crystals, and the cut edges were deeply etched prior to annealing. Laue photographs were made using 40-kv tungsten radiation. The technique used to disclose the various subboundaries was an electropolish and electroetch in a bath of chrome-acetic acid.' The anodic polishing done at 22 v was immediately followed by etching at a reduced voltage, which was dependent upon the nature of the subboundaries. Phenomenon of Laue Spot Sharpening on Annealing Cold-Rolled Crystals Fig. 1 gives the initial and final orientations of the specimens cold-rolled 12 pct. Each specimen was annealed at a temperature and for a time which caused significant structural changes as evidenced by alterations in Laue patterns. Representative Laue patterns and micrographs showing the essential changes are given in Figs. 2, 3, and 4. The essential points to be derived from these illustrations follow: 1. Annealing at 950°C clearly develops a substructure with the orientation of the cold-rolled specimen. 2. The subboundaries formed obviously separate regions of nearly the same orientation. Some of the subboundaries appear as a sequence of dots similar to those observed in aluminum by Lacombe and Beaujard,' but whether this is due to extremely small differences in orientation is not known at present. 3. The substructure coarsens upon prolonged annealing. 4. Prolonged annealing also causes a decrease in orientation spread according to Laue spot sharpening'

Jan 1, 1952

By J. P. Boisseau, C. N. J. Wagner, E. N. Aqua

An analysis ulas made of powder-paltern peaks from cold-rolled polycrystalline copper and from copper powders, compacted into briquets (1 in. diameter) with pressures up to about 106 psi. Powder-pattern peaks from both contact faces were measured with a diffractometer and CuKa radiation. Laltice-parameter measurements indicate the presence of residual stresses in the bulk specimen of the order of a - -10 kg per sq mm after 93 pct reduction in thickness, and give some evidence for the occurrence of deformation stacking faults (probability a - 0.003) in both bulk and powder samples. Fourier analyses of the line profiles were carried out on the (111) - (222) and (200) - (400) Pairs of reflections. The particle sizes decrease rapidly with increasing deformation and reach asymptotic values of De (111) = 550A and D, (200) = 350A at about 25 pct reduction in thickness or 80,000 psi pressure for compaction. The anisotropy of the particle sizes indicates the presence of microtwins and stacking faults on (111) planes. The rms strains increase also with deformation and reach limiting values of 2 x 10-3 in the [100] direction and 1 x 10-3 in the [Ill] direction at a distance L = 100A normal to the reflecting planes. THE diffraction of X-rays in cold-worked, polycrystalline, fcc metals and alloys yields Debye-Scherrer patterns in which the individual (hkl) lines may show a broadening, a shift, and an asymmetric shape.' These effects can be explained by the fragmentation of the small, coherently diffracting domains, the presence of residual elastic strains in the lattice, and the formation of stacking faults. X-ray studies of stacking faults in fcc metals and alloys have been methodically performed during the last few years, but so far most of the investigators dealt with cold-worked powder specimens obtained by filing.2-8,10-19 In such specimens, the crystals are randomly oriented and the average elastic strains are assumed to be zero, so that the observed peak shifts are due to stacking faults only. The agreement between X-ray diffraction theory1,20 and experiment is generally good. On the contrary, cold-worked, polycrystalline bulk specimens (after wire drawing, rolling, plastic deformation by tension or compression, etc.) contain residual elastic strains, which may not average to zero in the surface of the specimen and show very strong preferred orientation of certain lattice planes (texture) parallel to the specimen surface. Nonzero elastic strains also produce peak shifts, the magnitudes of which depend upon the crystallographic orientation of the reflecting lattice planes in elastically anisotropic materials as well as on the type of plastic deformation and which have to be taken into account when measuring stacking-fault probabilities in deformed bulk specimens.21-23 The purpose of the present investigations was to perform a detailed X-ray analysis on a bulk specimen of a fcc metal deformed by rolling at room temperature and on powder of the same material deformed by compaction, and to compare these results with those previously obtained on cold-worked filings.18 Pure copper was chosen for this study since it is known to produce only a small quantity of stacking faults by filing at room temperature.3,16,17,19 The residual elastic strain in the surface of the bulk copper should be the predominant factor determining

Jan 1, 1965

By W. T. Cardwell

Physically absurd, triple-valued saturations appear in the straight-forward solution of the Buckley-Leverell equations for the displacement of oil by water or gas. From an engineering viewpoint, the triple value causen no difficulty. It is well known how it may be compensnted in order to obtain physically meaningful, numerical results. From a scientific viewpoint, the question still arises: What did the triple value mean? This paper explains how and why the triple value arose in non-capillary Buckley-Leverett theory. The discussion should serve as a background for the understanding and use of the modern method of characteristics in di.~pkzc(>ment theory. INTRODUCTION Displacement theory was introduced to petroleum technologists in 1 941 by Buckley and Leverett.' Their first equation, which they wrote down without derivation, was equivalent to the following: ?s/?t= - qr/F ?f/?r (1) where S = saturation of displacing fluid (a fraction) r = time q,. = total volumetric velocity of both the displacing phase and the phase being displaced (usually, but not necessarily, assumed to be a constant) F = porosity (a fraction) f - fraction of the total volumetric velocity that is the volumetric velocity of the displacing phase (assumed to he a function of S only x = distance. Buckley and Leverett called Eq. I "a material balance equation". Actually it is derived from both a continuity equation, or material balance equation, and Darcy's law. Buckley and Leverett jumped from their Eq. 1 immediately to their Eq. 2, which was the equivalent of the following: (?x/?t)x = qr/F df/ds = qr/F f'(s) (2) The jump from Eq. 1 to Eq. 2 involves apparently simple mathematics, but in that apparently simple mathematics lies a subtle point that is part of the key to the meaning of the triple value to be discussed here. Eq. 2 may be readily interpreted as saying that a point of constant saturation (on a saturation-vs-dis-tance curve) moves with a constant velocity that is proportional to the total volumetric rate, inversely proportional to the porosity, and is otherwise a function of the saturation itself. So that if one knows the derivativc with respect to saturation of the fractional flow function, f(S), for each saturation, one knows the velocity of each point of the moving saturation-vs-distance curve. The function f(S) can he determined experimentally and its derivative f'(S) can be calculated. It turns out that the experimentally derived f'(S) is not a monotonic function of S, but instead it has a definite maximum and declines away at both high and low saturations. This in turn means, in accordance with Eq. 2, that on a moving saturation-vs-distance curve, ccrtain intermediate saturations will travel faster than the saturations either higher or lower. The result is indicated in Fig. 1. In Fig. 1, the abscissas represent distances along a column of porous medium, which column is assumed to be uniform in cross-section perpendicular to the ab-scissal direction. The ordinates represent fractions of pore space occupied by the displacing phase, which may be either water or gas. It is assumed that the saturation is uniform over all planes perpendicular to the abscissal direction. The saturation is a function only of time and one space variable. Time variation of the saturation is represented by change in shape of a curve such as curve AGJ, which represents the initial saturation-vs-

By R. A. Burton, J. T. Hansford, D. A. T. Donohue

Substantial evidence indicates that many petroleum producing horizons contain naturally occurring, ordered fracture systems and that within a particular geologic zone, vertical fractures induced in wellbores often will be directed along a particular compass direction. Both conditions will seriously alter the fluid displacement behavior within reservoirs. In this study the effect of induced fracture orientation and length on sweep efficiency is determined for a five-spot pattern. In general, it is assumed that all wells are fractured and directed along the same compass direction. Using the electrical analog to steady state, two-dimensional fluid flow in porous media, boundary conditions are obtained from which flood fronts are tracked numerically. The numerical computations require a particle tracking routine for approximating flood front histories. It is shown that recovery is sensitive to the length and orientation of fractures for the pattern studied. with the proper design of fracture-pattern systems, recovery can be enhanced considerably. INTRODUCTION Hydraulic fracturing introduced in 1949l gave the industry a rather inexpensive means of increasing the fluid injection or production capacity of wells. It has been used with particular success to increase the production rate of wells completed in tight formations, such as in western pennsylvania2 where producers have fractured in depleted or near-depleted fields and observed economic responses. Once the natural energy declines in such a reservoir where all wells have been fractured, waterflooding is generally suggested as means of further increasing recovery. Of the dual objective sought in waterflooding — high injectivity and high breakthrough sweep efficiency — the former condition can be obtained if all wells in the flood pattern are fractured; the latter condition should depend on the nature of the fracture system. Considerable theoretical work has been published on the nature of fractures induced in boreholes.3-5 Although discussion persists concerning the possibility of forming a horizontal fracture at a given point within the wellbore, it is generally conceded that only vertical fractures will develop below a given depth, i.e., where the fracturing Pressure is less than the overburden load. Given the fact that fractures will be vertical in most cases of interest, it is also important to know whether there is order to fracture orientations within a given geological region. Kehle has suggested that in tectonically relaxed areas of uncomplicated geology, the stresses are fairly uniform and all fractures in the region should be parallel.5 Dunlap arrived at a similar conclusion in a theoretical investigation of localized stress conditions surrounding the borehole.6 He concluded that most vertical fractures are propagated in a preferred azimuthal direction. Fraser and Pettitt, in extending these theoretical suggestions to a specific field case, used an impression packer to record both a vertical fracture and the orientation of this fracture in the wellbore of a well in the Howard Glasscock field, Tex.7 Use of this information enhanced the waterflood recovery of the field. Anderson and Stahl also used impression packers on three fractured wells in the Allegheny field. N. Y.. and found that the fractures were oriented more or less along the same compass direction.8 Orientation of the fractures in this manner depends on the stress condition within the formation during fracturing. Elkins and Skov have demonstrated that a natural, oriented, vertical fracture system exists within the Spraberry field? Heck suggests

Jan 1, 1969

P. L. Pratt (University of Birmingham, Birmingham, England)—The author has measured the hardening effect of isolated edge and screw dislocation boundaries in a remarkably elegant manner, and he proposes that the detailed structure of the boundary determines its effectiveness as a barrier to slip although "there are still unknown details of the distribution which may be extremely important." On p. 678 the author states "that for a good crystal (one having a yield of about 30 psi) a change in annealing temperature from 300" to 400 °C resulted in a negligible shift in the level of the stress-strain curve." Is this in agreement with the results of the earlier paper by Li, Washburn, and Parker8 in which such a change of temperature produced notable hardening in crystals with a yield of about 30 psi? Or were these earlier crystals, of the same nominal purity, less perfect than those used in this work? The experiment illustrated in Fig. 15, p. 681, shows that the boundary has sharpened after annealing at 400 °C, the temperature at which the hardening effect first becomes apparent. Did the author verify that no sharpening of the boundary occurred at, say, 300 °C where no hardening was found? This would seem to be an important check on the proposed mechanism, especially since zinc of this purity should polygonize at temperatures well below 400 °C within the annealing times used here. There seem to be at least two alternative explanations which could fit these facts: 1—The boundary may sharpen at 300 °C or even lower temperatures but be unable to contribute greatly to the hardening until jogged by thermal vacancies and other impurity atoms after 400 °C anneal. This mechan- ism, discussed in the earlier paper,' is believed to account for the thermal hardening observed by Blank'" in NaCl, as stated elsewhere: and by results from recent experiments which tend to confirm this view. 2—The dislocations in the diffuse boundary may be locked by impurity atoms at 300 °C and thus only sharpen the boundary at 400 °C with the aid of thermal vacancies. In this case it would be difficult to distinguish between the two sources of hardening (sharpening or jogging), using metal of this purity. Jack Washburn (author's reply)—The author wishes to thank Dr. Pratt for his discussion. In connection with his first comment, it should be pointed out that the temperature of testing in the present series of experiments was —196°C, whereas, in the earlier experiments he referred to,' it was 20°C. Therefore, the yield values should not be directly compared. It is likely that the crystals used in the present work were initially more perfect macroscopically than the large shear specimens used previously. The small size of the test section in the kink specimens made it possible to select regions of the large crystals, from which they were acid-cut, that were free of observable small angle boundaries. The sharpening of a microscopically diffuse boundary such as that in Fig. 15 begins in zinc of this purity well below 300°C. However, it is probably not justified to conclude that because a boundary looks sharp under the microscope it has attained the ideal structure. The author agrees with Dr. Pratt that jogging of dislocation lines is one of the structural features of a small angle boundary that should be important in determining its strengthening effect. More detailed information concerning the changes in boundary structure as a

Jan 1, 1956

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By E. L. Vickers

Over the years, the pure theorist in economic analysis has accumulated a formidable array of facts in bringing his subject matter under control. Business managers and mining engineers are aware of the theorist's weapons, but the question of applying them to the mastery of practical problems seems hardly feasible, especially in view of the almost innumerable variables plaguing the everyday scene in the mining enterprise. One such sophisticated tool of long-standing in the theorist's arsenal is marginal analysis. Equally long-standing for the operating company and valuation engineer is the problem of defining the cut-off grade the point below which a mineral re- source ceases to be economically amenable to extraction. In other words, what part of a mineralized body of rock is ore and what is waste?

Jan 6, 1961

By AIME AIME

IN furtherance of the policy of acquainting those members of the Institute who live at a distance from New York with all the details of administration, the thirty delegates sent by the local sections and the technical divisions were invited to attend the meeting of the Directors on Tuesday evening as well as the Directors' dinner immediately preceding. Including the Directors and officers, new and old, the members of the Papers and Publications Committee and the section delegates, more than 70 sat down at the dinner table in the Engineers Club. The attendance at the business meeting that followed was not quite so large, doubtless for the reason that the ladies' fashion show, held in connection with the informal dance, offered attraction that eclipsed that of watching the wheels of Institute business go around.

Jan 1, 1930

By AIME AIME

HENRY DAYTON WILDE-"Date," informally- manager- of the technical and research department of the Humble Oil & Refining Co., was born at Aguascalientes, Mexico, Sept. 25, 1900. He is a graduate in chemical engineering: M.S. from the University of Texas and I Sc.D. fro111 the Massachusetts Institute of Technology. t For a year and a half in 1926 and 1927 he was a research : associate in the research laboratory of applied chemistry at M.I.T., under W. K. Lewis. In the latter year Dr. Wilde went with the Humble as head of the laboratory experimental division of its refining development department. In 1929 he was made director of production research. Dr. Wilde is the author of important papers in the TRANSACTIONS of the Institute, wherein are also mans dis-

Jan 1, 1938

In discussing Mr. Keller's paper, I quoted the results obtained by Mr. Allan Gibb, correctly crediting them to Mr. Gibb, with due reference to the report in which they were published. But in the table immediately following, and in my further remarks, following the table, I find that, by some clerical or other error which I cannot, after the lapse of time, explain, I spoke of Mr. Gibb as Mr. "Dean"—a metallurgist who had written on a related subject, but not on the point I was discussing. In short, my reference throughout was to the work of Mr. Gibb; and by reading a Gibb " for a Dean " in all places on pp. 832 and 835 where the latter name occurs, my remarks will be brought into accordance with my intention, and with the facts.

Jan 1, 1901

By AIME AIME

In the uniform of his country for the second time, Harry Phillip Stolz. Chairman of the A.I.M.E. Petroleum Division, holds a commission as Lieutenant-Commander in the Naval Reserve and is attached to the office of Inspector of Naval Petroleum Reserves in California. During World War I he left his studies at Stanford University to join the Army and was granted a commission as Second Lieutenant of Infantry. He remained in the Army Reserve until 1938 when he resigned to accept a commission as a member of the Naval Petroleum Reserves Advisory Board. Born in San Francisco Jan. 29,1899, where his father had lived since 1880, he was in that city during the turbulent year of 1906 where the city was ravaged by fire and earthquake.

Jan 1, 1942

By Alexander Anderson

TABLES showing the drift and inclination of wells surveyed in the years 1924 to 28' and in the year 1929' have already been published. Each of these tables included a little over 1,000,000 ft. of rotary hole. In the year 1930 the table -shown-in . Fig. 1, comprising, the results of surveys .of 1,030,344 ft. of hole and representing 11,642 individual survey readings, was compiled. For that purpose we selected 'I only wells that had been drilled in California during that year. The footage of Fig. 1 differs from the two earlier tables in that the wells were all drilled in the year 1930. In the earlier tables, the footage shown was surveyed in the years designated, but some of the wells were drilled in earlier years.

Jan 1, 1931

Virginia Polytechnic Institute, Department of Mining Engineering, Blacksburg, Va Otto C Burkhart, Professor of Mining. The titles of pertinent publications have been abstracted from the Bulletins on Research and Publication This material has also appeared, in most cases, under other auspices Presumably, the Bulletins whose titles are quoted may be had for the cost of postage The coals of Virginia (1927), Ceramic resources of Virginia and their development (1929), Effect of ilhum crucibles on volatile determinations of coal (1930), Possibility of briquetting southwest Virginia coals (1930), Coking of semi-anthracite coal of Virginia (in preparation), Distribution of ash in the Merrimac coal seam (1929); Unit coal studies on some Virginia coals (1931), Sulphur forms in Virginia coals (1931); Comparison of results of fusion point of coal ash obtained by two different methods

Jan 1, 1933