Search Documents

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.' Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. 'From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By R. F. Blakely, P. E. Potter

Any stratigraphic section or bedding sequence can be synthesized if there is a transition procedure from one lithology or bedding type to another, and if thickness distributions of the different lithologies are known. Stratigraphic sections of a fluvial sandstone body were synthesized with five bedding types: cross-bedding, massive beds, parting lineation, ripple mark and mudstone. The transition procedure from one bedding type to another used dependent, Markovian random processes which have a memory that extends one step backward in the depositional process. As observed in nature, median grain size and sand wave thickness (cross-bedding and ripple mark) decline upward in the synthesized sections as proportions of the different bedding types change. Grain size and permeability were also incorporated into the sections. By changing the transition procedures, bed thickness distributions, rate of upward decline or sand wave height and length, different types of sections can be synthesized, thus making it possible to model many different sedimentation problems. INTRODUCTION This paper describes a general method for synthesizing stratigraphic sections and bedding sequences of sedimentary, metamorphic or igneous origin. Synthetic generation is of interest for several reasons. Close correspondence between real and synthetic sections suggests that the factors used in the synthesizing model may indeed be the correct ones, thus giving the investigator a check on his assumptions. Rapid, inexpensive simulation of many stratigraphic sections permits one to synthesize a rock body (sandstone or carbonate reservoir) or, on a larger scale, the fill of a sedimentary basin. Harbaughl gives an example of mathematical simulation of a carbonate basin. He simulated the basin in the hope that improved prediction would follow better understanding of the depositional processes. From the petroleum engineer's viewpoint it seems reasonable to believe that the synthetic generation of rock properties and their distribution in a reservoir should be relevant in the study of reservoirs. Any stratigraphic section or bedding sequence can be generated provided there is a transition procedure from one lithology or bedding type to another, and provided the thickness distributions of the different units are known. The transition procedure involves random processes that are either independent or dependent. If the depositional process is independent, previous deposition will have no influence on present deposition. However, if it is dependent, past deposition will influence either present or future deposition. Such a dependent depositional process can be thought of as having a memory that extends backward in time through one or more pulses of deposition. A process with a memory can be described by a Markov process. Because the concept of memory or dependence appears to be in accord with our understanding of many depositional processes, Markov processes were used to synthesize the bedding sequences of this study (see Appendix). The above methods are perfectly general and are appropriate for any stratigraphic section or bedding sequence: bedding types in a beach deposit, an evolving carbonate bank or the changing lithologic fill of a thick geosyncline sequence. We chose to synthesize a vertical profile of a fluvial sandstone body because its characteristics were well documented, much was known about fluvial processes and fluvial-deltaic sandstone bodies constitute an important class of petroleum reservoirs. CHARACTERISTICS AND ORIGIN OF FLUVIAL CYCLE The fluvial cycle has been well documented in recent years by Bersier,2 Allen3-5and Visher.6,7 Deposits from fluvial cycles range from 10 to 150 ft or more in thickness and are characterized by a "fining upwards": coarse sandstones with occasional conglomerates grade upward into medium- to fine-grained sandstone, and hence into siltstone and mudstone. The dominant sedimentary structure is inclined bedding: thick cross-beds in the lower half

By W. A. White

UNDERCLAY squeeze is the plastic flowing of underclay below coal pillars into mined-out entries and rooms. Squeezes may be caused either by wet mine conditions where the moisture is taken up by the clay—making it more plastic—or by the presence of certain clay minerals, such as mont-morillonite, which are plastic when there is enough natural moisture. Under either condition, sufficient stress will cause the underclay to flow. Squeezes may fill an entry or room within several hours, or it may be several months before movement stops. Squeeze areas commonly cover hundreds or thousands of square yards. The Coal Div. of the Illinois State Geological Survey has collected samples of underclays from various mines and from cores drilled by coal companies in the state. From these samples natural moisture content, particle size and particle size distribution, and clay mineralogy are determined. Data from samples collected from the underclay below Herrin (No. 6) coal in the Lumaghi Coal Co. mine near Collinsville, Ill., are used in this report to clarify points in the discussion. Data from samples taken from other mines lead to the same conclusions. A generalized geological section for the area is given in Table I. The underclay below coal No. 6 ranges from a few inches to 3 or 4 ft thick. The upper 6 to 18 in. are noncalcareous; the lower part becomes more calcareous with depth. Limestone nodules become larger with depth, almost grading into the limestone below. In areas where the clay is nearly absent the limestone may thicken to take its place; thus they may complement each other in thickness. There are two types of squeeze areas in a mine. In one type up to 3 or 4 ft of underclay lie in what appears to be a depression in the limestone underneath. This is suggested by a rim surrounding the squeeze area where the underclay is thin and the limestone lies within a few inches of the coal. In the second type the underclay of the squeeze area is surrounded by underclay of similar thicknesses which does not squeeze. Test Methods: Natural moisture content, particle size and particle size distribution, and clay mineralogy were determined by the following methods: Natural moisture is the moisture content a clay contains in its natural environment, expressed in percentage of the weight of ovendried clay (110°C or 230°F). To obtain the natural moisture content, given in Table 11, the clay samples were sealed in containers as soon as the samples were taken in the mines. Particle size and particle size distribution were determined by the pipette method,' and the data were plotted as cumulative curves, Fig. 1, on semi-logarithmic paper. Particle size was plotted on the logarithmic scale and percentage on the arithmetic scale. The quartiles (diameters that correspond to frequencies of 25 and 75 pct) and medians (diameters that correspond to the frequency of 50 pct) of the samples were determined from these curves. The clay minerals were identified from the data obtained by differential thermal' and X-ray powder" techniques. The differential thermal analyses were made on the whole samples, whereas the X-ray analyses were made on fractions of less than 2p. Data and Discussion Moisture Content: After the sealed jars had stood for 24 hr, those that contained squeeze samples had perspired, so that droplets of water had accumulated on the insides of the jars. Table II shows the moisture in the clay after it had perspired for 24 hr. (This perspiring was not noted in samples from nonsqueeze areas.) After perspiration one of the squeeze samples still had a higher moisture content than the samples that did not squeeze. Clay Mineralogy: The thermal analysis, Figs. 2 and 3, indicates that the clay minerals are chiefly micaceous in type; the low-temperature endothermal

Jan 1, 1957

By J. J. Scott

This investigation utilizes three dimensional photo-elastic techniques to determine the stress distributions in the pillars and the roof of a room and pillar mine model. Castolite plastic was used for the construction of the model in which a stress pattern was developed by the stress freezing process. Analysis of the stress pattern was accomplished by observation of points in slices from the model with a polariscope and solving the data thus obtained by the shear-difference method. Slices through the centerline, edge of pillar and centerline of span were investigated. The results of this work provide information on the overall stress distribution in points of stress concentration in compression, shear and tension, show relative magnitude of stress throughout the model and indicate directions of the most important stress values. A generalized roof bolt pattern is developed for room and pillar mines based on the stress distribution. A digital computer was used in the reduction of data and proved to be extremely useful for investigation of this type. Underground excavations disturb the equilibrium of the earth's crust and a core of fracture, or altered stress distributions exists around the openings. This fact is well known by mining operators and investigators in the rock mechanics field. Analysis of the stress distribution in the areas around mine workings is a most difficult problem and one which has no simple and direct solution. Some of the approaches used by investigators in attempts to study stress distribution around mine openings involve mathematical analysis, photoelastic techniques, statistical analysis, model studies on brittle materials and observation of fracture patterns. Models involving imbedded strain gauges, gelatin models using imbedded strings to show internal movement, and many other unique laboratory techniques are employed. Work is also being done in mining operations where load cells, strain gauges, photostress material, convergence plugs, dynamic plugs, etc., are used to measure strain which can in turn be used to obtain stress. Some of these devices measure strain from which stress may be derived. All approaches to the solution of stress distribution are hampered by the fact that the earth is not a homogeneous, isotropic and elastic media. Geologic faults, fractures, bedding planes, vugs, variations in material composition, variations in grain size and structure, etc., make it extremely difficult to obtain results which can be universally applied to mining operations. The purpose of this investigation will be to demonstrate the use of three-dimensional photoelastic techniques to obtain the stress distribution in the pillars and roof of a room and pillar mining operation. This method utilizes full analysis of interior points, and thus it may be that small tensile or shear stresses found in the investigation will prove to be of greater significance than the more obvious points of stress concentration found by two-dimensional techniques. A digital computer was employed to simplify and to shorten the time necessary to obtain final results. Application of the computer to problems of this type may enable future investigators to attempt more elaborate analyses than have been previously considered feasible. THEORY Three Dimensional Stress Analysis-Shear Difference Solution:' Photoelastic studies are based on the fact that an optically isotropic transparent solid becomes optically anisotropic when subjected to forced deformation; the degree of optical anisotropy being proportional to the deformation of the material. There are two fundamental laws which govern photoelasticity: 1) Light is polarized in the directions of the principal stress axes, and is transmitted only on planes of principal stress. 2) The difference in principal stresses is proportional to the difference in the indices of refraction along the planes of principal stress. One method used in three-dimensional photoelastic work is to examine a slice of the object by normal incidence and oblique incidence. In normal incidence,

Jan 1, 1964

By R. A. Morse, C. R. Holmgren

The production of oil by water flooding can be substantially increased by the maintenance of free gas saturation in the reservoir during the flooding operation. This effect is accomplished by the alteration of oil relative permeability characteristics and the occupation by gas of pore space that would otherwise be filled with residual oil. The amount of reduction In residual oil can be calculated from appropriate water-oil relative permeability characteristics. This paper presents experimental data in support of the foregoing conclusions and an example of the calculations. The microscopic pore saturation concepts of the mechanism are discussed. A method of practical application to field floods is presented together with discussion of certain limitations. INTRODUCTION The presence of free gas has been reported by a number of investigators to significantly affect the oil recovery which can be obtained from sandstone flow systems by water flooding.1,2,3,4,5 The effect of gas, noted in every instance, has been to cause lower residual oil saturations than could be obtained by water flooding the same systems in the absence of free gas. The degree of improvement in recovery has been observed to vary widely, depending on the systems used and the conditions of the tests. The increased oil recovery obtained because of the presence of gas during a water flood has been variously attributed to changes in physical characteristics of the oil, selective plugging action of the gas, inclusion of oil mist in the free gas phase, and the additional sweeping or driving action of the free gas. All but the first of these suggestions imply changes in the displacement mechanism. The change in viscosity and inter-facial tension of the oil phase, within the pressure range used for all the experimental work, is certainly not sufficient to account for the differences in residual oil saturation noted dess there is a drastic change in the displacement process. One other effect which logically seems capable of causing differences in residual oil saturation of the magnitude noted in the experimental work is that of simple replacement. In a water-wet system containing oil, water, and gas, it is to be expected that the gas will exist inside the oil. This is the position of minimum free surface energy, since the gas-oil interfacial tension will be less than the gas-water interfacial tension. There is no apparent reason to expect that the existence of free gas within the oil phase should alter the saturation at which the non-wetting phase (now oil and gas) should become discontinuous and hence trapped so as to be unrecoverable by direct displacement by water. If this is the situation, then trapping of a certain percentage of gas saturation during water flood should result, at infinite water-oil ratio, in a like reduction of oil saturation below that attainable by flooding in the absence of free gas. It is visualized that the gas will exist as bubbles inside the discontinuous residual oil as illustrated in Fig. 1, with the size of the oil bubbles being substantially unchanged due to the presence of the gas. As a practical matter, it can be anticipated that the presence of a free gas saturation inside the oil phase will reduce the relative permeability to oil which will exist at any particular water saturation. This reduction will be caused by two factors — -the addition of the gas-oil interface, and the reduction of area available for oil flow in the pores containing gas. This reduction in oil permeability at any particular water saturation will result in water breakthrough at a lower water satu-

Jan 1, 1951

ONE of the largest hard rock operations ever undertaken on the continent is part of the Aluminum Co. of Canada's gigantic British Columbia development in the mountainous wilderness back of the north coastal port of Prince Rupert. To provide electric power for the huge aluminum smelter under construction at Kitimat, 400 miles northwest of Vancouver, Alcan is reversing the flow of a 5000 sq mile drainage area by blocking the eastward-flowing Nechako River with the largest sloping clay core dam in the world. The backed-up waters of a 110-mile chain of lakes will be tapped at their eastern end by a 10-mile tunnel piercing a mile-high mountain range. From this tunnel water will pass through penstocks to a subterranean powerhouse after a drop of 2600 ft and empty into the Kemano River almost at tide water. A projected battery of eight turbine-driven generators will produce more than a million horsepower, although, initially, three generators of 140,000 hp each will be installed. Power will travel 50 miles across another mountain range, over a glacier, and across an arm of the ocean to what will ultimately be the world's largest aluminum smelter-a plant 2 ½ miles long. Ore smelted at Kitimat will come from Jamaica, but carving the tunnel, penstocks, and powerhouses cavern out of the heart of a mountain is so vast a job that most of the problems of a major mining operation are encountered. The powerhouse cavern alone is a big hard rock job. This chamber lies 1400 ft back from the mountain face and will eventually be 1100 ft long, 80 ft wide, and an average 118 ft high. Now under construction, the roof of this cavern will take the form of a parabolic arch. The prime contractors, Morrison-Knudsen Co. of Canada, are to excavate a length of 700 ft by May 1954. This section will provide a main control room, erection bay and space for eight generating units. The roof arch is to be lined with reinforced concrete and a plan now under study provides for concrete curtain walls separated from the rock sides of the cavern to prevent moisture accumulation. Cavern Excavation Excavation of the cavern began with the driving of an 8x8-ft exploratory drift 1500 ft long. Two horseshoe-shaped access and tailrace tunnels were bored to serve excavation work. These tunnels are approximately the same length as the exploratory drift and 25 ft high. The floors of both tunnels were graveled to permit the use of rubber-tired equipment. Eventually, the tailrace tunnel will be enlarged to 40 ft height to drain water from the turbine pits below the powerhouse floor. When the tunnels reached the cavern location, a mucking tunnel, approximately 25 ft square, was driven the projected length of the powerhouse at the floor level of the cavern. Another tunnel, 10 ft square, was carried in the same direction from the exploratory drift at the level of the arch spring line, 65 ft above the cavern floor. To connect these two tunnels, seven shafts 10 ft wide and approximately 80 ft long were driven through to the lower mucking tunnel, 65 ft below. These shafts were located on 120-ft centers, the length of the powerhouse cavern. Blasting is done from this upper tunnel to the final line of the roof arch. Two bulldozers, an International TD-24 and a TD-9, doze blasted material to the shafts where it drops to floor level. From here, the rock is loaded by Eimco loaders and power shovels into rubber-tired Koehring Dumptors and Euclid end-dump trucks. The arched roof section will be completely excavated and concreted before vertical blast holes are drilled down from the level of the arch spring line to the floor of the cavern. The arched roof section with its parabolic curve will have a width of 80 ft and a rise to the crown of 47 ft.

Jan 1, 1952

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

By R. S. Kinasevich, D. D. Crabtree, D. W. Fuerstenau, T. P. Meloy, A. L. Mular

This paper presents details of the concept that size reduction in comminution machines takes place by three mechanisms; namely impact, abrasion, and chipping grinding. Experimental evidence is presented to show that each of these comminution mechanisms produces particles of a characteristic size distribution. The actual product from a comminution device has been postulated to be the result of a composite of these three types of mechanisms. Composite curves are demonstrated for a material following the Gaudin-Schuhmann, Gaudin-Meloy, and Rosin-Rammler size distributions. About forty years ago, Gaudin1 showed that grinding may be considered a combination of impact and attrition. Since that time, major efforts have been devoted to studies, both experimental and theoretical, of impact and compression fracture, while attrition has been almost wholly neglected, at least quantitatively. A significant attempt to distinguish between attrition and impact grinding is the work of Tanaka2 in Japan. By means of an instrumented abrasion grinder and a drop weight device, he determined coefficients relating the increase in surface area of various materials to the energy expended by the two methods of comminution. He showed that physical properties of a material determine its response to attrition and impact grinding. By extending his ideas to ball milling, he concluded that to a large extent the basic comminution process in a ball mill is due to the impact of falling media. Because Tanaka used a mass of particles in his drop weight device, however, he did not obtain pure impact size reduction. The purpose of this paper is to define basic mechanisms of size reduction, to verify that each has a characteristic and meaningful distribution curve, and to show how a combination of these mechanisms results in a size distribution very like that produced by grinding mills. DEFINITION OF COMMINUTION MECHANISMS The product from a grinding device will be considered to be the sum of the contributions resulting from the action of three basic mechanisms of size reduction which operate in a ball and rod mill. These are impact grinding and two forms of attrition, namely abrasion grinding and chipping grinding. Each is defined below. Impact Grinding: If a straight line is obtained when the cumulative weight fraction finer than a given size is plotted on log-log paper as a function of that size, the slope of the line is defined as the distribution modulus. A number of investigators 3,4,5 have shown that impact fracture of single specimens of different composition and shape results in a distribution of daughter particles that exhibit a distribution modulus of unity. This has also been true for materials broken in slow compression. Moreover, under slow compression or impact fracture conditions, theoretical distribution equations6*' which approximate the Gaudin-Schuhmann distribution when the distribution modulus is close to unity agree reasonably well with the experimentally obtained products. If one now considers a comminution process where many impact or compression fracture events are taking place, then any rational summation of the individual events yields, in the finer size range, a Gaudin-Schuhmann distribution whose distribution modulus is also unity. If the size distribution of the product from a mill has a distribution modulus of unity, it is implied that particles are fractured in a manner which results in a comminution event having a distribution like that obtained for the breakage of single specimens. These impact events would occur when a particle is smashed between balls or between a ball and the mill liner. Attrition, on the other hand, is that form of grinding which cannot be called impact grinding, and comprises both abrasion and chipping grinding. Abrasion Grinding: Abrasion is a form of surface wear resulting when particles rub against each other or against balls or the mill liner of a tumbling mill, somewhat like a piece of wood being rubbed over a piece of sandpaper. The surface wears at a more or

Jan 1, 1964

By J. B. Agan, R. J. Fernandes

This paper utilizes the layered-system approach, modified to include areal sweep efficiency, to determine the miscible-slug size required and to predict the perfort7zance of a miscible-slug process in a highly stratified reservoir having a permeability variation of 0.76. The slug size in each layer was determined from theoretical calculations and laboratory data which showed that, to maintain miscibility in the reservoir, the slug size had to be 8.2 per cent of the floodable hydrocarbon pore volume. Economic considerations, however, such as the value of the miscible product injected, the cost of injection and the cost of reprocessing the miscible product, limited the amount of miscible product which could be injected into the lower-permeability layers. This resulted in subjecting only 60 per cent of the reservoir to a slug size sufficient to maintain miscibility. Utilizing the relationship of producing gas-oil ratio and areal sweep efficiency as a function of pore volume injected (as obtained from data published by Dyes, Caudle and Erickson2), the theoretical performance was determined. This prediction is compared with actual performance to date. Actual performance reflects an increasing percentage of tniscible product in the produced fluid to a particular level, which remains static for a short period and then increases again to a higher level. This performance suggests that the reservoir has performed as a layered system. It is concluded that the layered-system approach can be used to predict performance in a highly stratified reservoir and that economic consideration is a limiting factor in determining the amount of the reservoir which can be miscibly swept. INTRODUCTION The Paloma zone in the Paloma oil field, Kern County, Calif., is comprised of several sand members separated by siltstone, shale and/or cherty sections. Rapid facies changes within the zone indicate that the sediments were deposited in a "near shore" environment. As a result, the Paloma sands have a high permeability variation, and the Paloma zone is comprised of several sand reservoirs. Since one of the sand reservoirs containing crude oil was not receiving the benefits of gas injection, consideration was given to recompleting certain wells to isolate the sand in order to perform a miscible-phase injection project and, thereby, to increase its ultimate oil recovery. Before proceeding with the project, a review of the literature was made to determine the miscible-slug size that would be required to maintain miscibility throughout the displacement process. Although the review showed that considerable information was available for homogeneous systems, insufficient information was available to determine slug-size requirements and to predict performances for a highly stratified reservoir. This paper has been prepared to describe the method used to determine the miscible-slug-size requirement and to predict the performance of the miscible-phase injection project initiated in the Paloma oil field. Although the Paloma project has only been in operation since Aug., 1958, sufficient production history has been obtained so that a comparison can be made with the predicted performance. DESCRIPTION OF RESERVOIR The reservoir in which the miscible-phase project was initiated in the Paloma field is shown on Figs. 1 and 2. Reservoir properties are as follows: average sand thickness, 43 ft; porosity, 19.1 per cent; water saturation, 47.2 per cent: oil viscosity, 0.328 cp; reservoir temperature, 250°F; reservoir pressure, 3,500 psi: gas saturation, 21.2 per cent at time of miscible product injection; and total net hydrocarbon pore volume, 19,993,000 reservoir bbl. LIMITATIONS The method described herein utilizes a layer-system approach, where injection into and production from each layer is assumed to be proportional to the layer's fractional capacity. The effects of increased fluid mobility on injection and production rates, in layers which have had breakthrough, are not reflected in this method. There has been considerable controversy over the slug size necessary to maintain miscibility throughout the displacement process. In this method, the slug-size

By W. O. Brown

A laboratory investigation was conducted to determine quantitatively the extent to which connate water was contacted and displaced by invading flood water. In these experiments the connate water in unconsoli-dated sand packed columns was completely displaced by injecting water. The nature of this displacement was similar to that previously described for single-phase miscible fluid displacement studies, and thus the presence of a non-wetting immiscible phase did not appreciably change the nature of the displacement. The effects of water injection rate, column length, and oil viscosity on connate water displacement were investi-gated. It is concluded that the connate water in a reservoir is the water which actually displaces oil from the pores of the rock during a water flood. During a water flood the connate water forms a zone which separates the invading flood water from the continuous oil phase. The size and shape of connate water bank is chiefly dependent oil the oil viscosity and the column length. INTRODUCTION Water flooding is one of the most widely used techniques for the secondary recovery of oil. Presently, however, it is still not possible to recover all the oil in a reservoir by water flooding. The research described in this paper was conducted as part of a study to determine the conditions under which 100 per cent oil recovery could be attained by water flooding. The particular objective of this work was to determine if any chemical agent, regardless of its nature, placed in the flood water could be effective in influencing the mechanism of displacement of the oil by water. It has been known for many years that water does not displace all the oil in a reservoir because a portion of the oil is "trapped" and held immobile by capillary forces. This oil is trapped within the pores of a water-wet rock when it becomes broken into discontinuous globules. Initially, when oil is present at high saturations within the pores of a water-wet rock, the connate water forms rings around the points of contact of the sand grains and may even completely fill small cavities between grains, whereas the oil occupies the larger void spaces between the grains.' Under these conditions, the oil in these spaces is in the form of irregular but continuous filaments, the diameters of which depend on the geometry of the sand pores. The filaments are formed by the oil contained in the small cells which are formed between the sand grains and are connected to their neighboring cells by channels or tunnels formed by pendular rings of water. At a high oil saturation, the oil filaments conform approximately to the shape and size of the cells and their connecting tunnels. Starting with this distribution, as the water saturation is increased the water layers in the small cavities and on the surface of the grains grow. As this occurs, the water rings grow and the diameters of the oil filaments decrease. When an oil filament is reduced to a critically small diameter, the filament breaks, and its tunnel fills completely with water. Any oil which remains within a cell after all its connecting tunnels have been water-filled is trapped as a discontinuous globule. Once the oil has become trapped, the capillary forces oppose distortion of the globules and may prevent their being squeezed through the water-filled tunnels. Only a very small pressure gradient is sufficient to keep oil moving as a continuous filament. On the other hand, once the filament has broken into discontinuous oil droplets a relatively large force is required to distort the surface of a drop and move it through a water-

Jan 1, 1958

By J. Husson, R. Iffly, M. Gondouin

A systematic variation of well deliverability, as reflected from isochronal back-pressure tests performed at regular intervals, has been observed in some gas condensate wells producing at high rates. The same effects have been obtained using a numerical model of gas and condensate flow which takes into account secondary gasoline deposited in the pore space as a result of pressure reduction, and non - Darcy flow of gas in the vicinity of the wells. Matching calculated values with previous test results has been possible, and future predictions have been obtained. An application of this method to the Hassi Er R'Mel gas-condensate field in Algeria is tentatively shown. INTRODUCTION Flow capacity of gas wells is generally derived from an analysis of back-pressure tests. The empirical equation q = C (?p2)n used by Rawlins and Schellhardtl can be derived rigorously assuming that steady-state radial flow of a dry gas of constant viscosity and compressibility is established during each flow period of the well tests. Furthermore, when Darcy's law applies in the entire flow region, the theory predicts that the exponent n is equal to 1. In low-permeability reservoirs, it was soon discovered that the time required to reach a stabilized flow often exceeded the duration of the flow periods normally available for testing wells. Consequently, transient gas flow had to be considered instead of the steady-state assumption previously used. This led to the isochronal testing procedure established by Cullender2 which has largely replaced conventional back-pressure testing. For dry gas fields, this method yields definite values of C and n equivalent to those of the empirical equation. These values should remain constant for each well as long as the permeability of the formation and the characteristics of the gas (viscosity and compressibility) do not change appreciably. This is the case when reservoir pressure remains -close to the original value and when the formation near the wellbore remains free of plugging. Under those conditions, stabilized flow potential curves of gas wells can be established from a single sequence of isochronal flow and shut-in periods. An analysis of a pressure build-up following a longer production period provides additional data on the transmissivity (k h/ u) of the reservoir, and eventually on the 'drainage radius rd of the well, which can be related to the value of C so that future performance of the well can be predicted using the concepts developed by A. Houpeurt.3 At high flow rates, Darcy's law no longer applies in the vicinity of the wellbore, and inertial effects in the high velocity gas flow introduce additional pressure drops. As a consequence, exponent n of the backpressure tests becomes smaller than 1, and a slight curvature of the log-log plot of ?p2 vs q can be predicted when going from very low to high rates of flow (Elenbaas and Katz).5 The effects of variations of viscosity and compressibility with pressure on the radial flow of dry gas in an infinite reservoir were taken into account by Jenkins and Aronofsky.7 Numerical solutions of the transient flow of an ideal gas in finite radial reservoirs were presented by Bruce, Peaceman, Rachford and Rice.8 In the case of gas condensate wells, however, the presence of gasoline in the pore space as soon as reservoir pressure is reduced below the dewpoint pressure further complicates the interpretation of flow tests so that the prediction of stabilized well performance becomes very difficult. Field observation shows that both C and n derived from isochronal tests vary in time, even when reservoir pressure has not changed appreciably. Such a variation cannot be attributed to any change of the gas characteristics, and must result from the effect of a gasoline saturation on the gas flow.

By F. N. Rhines, B. H. Alexander

MUCH attention has been directed to the effects of grain size upon the properties of alloys, but there has been scant study either of the conditions that determine the pattern and dimensions of den-drites in metal systems, or of the influence of their shape and size upon the overall properties of cast-ings. The aim of the research that is about to be described has been to investigate the effect of vari-ous factors upon the mode of formation of dendrites in alloys by measurements of the distance between adjacent dendrite arms (dendrite spacing). Early investigators, including Grignonl and Tschernoff,2 showed that a metal dendrite is com-posed of a tree-like system of stalks and branches arranged in a simple geometrical pattern. North-cott and Thomas3 demonstrated that, in the face-centered cubic solid solutions of copper-base, these stalks and side arms all lie in (100) directions in the crystal. Several investigators, including Sauveur and Chou,0 Sauveur and Reed,' and Martin and Mar-tina have reported that the addition to steel of alloy-ing elements, such as nickel, chromium, and molybdenum, not only makes the dendrites easier to reveal by etching, but makes them coarser. The latter authors8 proposed that the coarsening of the dendrites is roughly proportional to the increase in the temperature range of freezing, caused by adding the alloying elements. Sauveur and Chou6 showed, in addition, that the dendrites are coarsened by a decreased rate of cooling of the casting. Measurement of Dendrite Arm Spacing Among the physical conditions that could be ex-pected to have an influence upon the dendrite arm spacing, that appears in a cast metal, are: composi-tion, rate of freezing, crystal structure, and type of constitution. The relationships obtaining between these variables and the dendrite dimensions have been examined, in the present research, by measur- ing the arm spacing in a wide variety of alloys, listed in tables II through VI. Alloy compositions are recorded in the tables by showing the symbol of the major metal followed by the percentage and symbol of the alloying agent; thus, "Al-10Ag" is an aluminum-base alloy containing 10 pct of silver. Although none of the alloys were analyzed, an im-pression of their degree of purity may be obtained from that of their component metals given in table I. Five hundred grams of each alloy was made by melting in small clay-graphite crucibles in an elec-tric muffle furnace. After alloying the temperature was adjusted to 50" to 75°C above the liquidus and the melts were poured into cast iron molds, at room temperature, the molds having a wall thickness of 1 in. and a cavity 11/2 in. sq in cross-section. Each ingot, thus cast, was sectioned at mid-height and the sectioned surface was polished and etched for metallographic examination. Dendrite spacing meas-urements were made at three positions, namely, ad-jacent to the mold wall, midway between the wall and the center of the ingot, and at the center (desig-nated e, m, and c respectively, in the tables). A typical series of microstructures is presented in fig. 1. For each measurement, the average was taken of the dendrite spacing of several grains covering a zone about 2 mm wide. Only those grains which had a major dendrite axis nearly in the plane of polish were selected in order to eliminate corrections for orientation differences from grain to grain. Although the dendrite spacings were measured to the nearest thousandth of a millimeter, the values listed in the tables are thought to be significant only to the nearest hundredth of a millimeter. The larg-est difference in readings found, when various ob-servers rated the same specimens, was 0.012 mm; the largest difference between corresponding meas-urements upon duplicate specimens was 0.027 mm.

Jan 1, 1951

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955

By S. S. Marsden, S. H. Raza

An experimental study of the flow of line-textured. aqueous foams through Pyrex tubes is described. The foams range in quality F (ratio of gas volume to total volume) from 0.70 to 0.96 and behave like pseudoplastic fluids. At lower flow rates they exhibit laminar flow ad have apparent viscosities which increase with quality, and which cover a range of 15 cp to 255 poise for tubes of 0.25- to 1.50-mm radius rj. At higher flow rates a plug-like type of flow is developed, the extent of which increases with both T and ri. When the same foams flow through either open or packed Pyrex tubes, remarkably high streaming potentials ?E are often generated. These can easily reach 50v if nonionic foaming agents are used, but are at least an order of magnitude less for ionic foaming agents. A linear relationship between ?E and the pressure differential ?p is observed; this usually extrapolates to positive values of ?p at ?E of zero. The slope of the line increases with both F and ri. An equation was derived to describe the streaming potential of non- Newtonian fluids in circular tubes and was used to correlate experimental results. The calculated < potentials are of the right order of magnitude. INTRODUCTION Foams are both unusual and inniguing in their physical properties, and have been the subject of many scientific studies. However, present knowledge of foams is still fragmentary, specific and often contradictory. Apparent viscosity of foam is the physical property of greatest interest to both rheo1ogists and engineers. sibreel reported that the apparent viscosity decreased with increasing shear rate in a manner similar to some non-Newtonian fluids. Penny and Blackman2 reported that fire-fighting foams had both a limiting shear stress and a tensile yield stress. There is little doubt that some foams at least behave like non-Newtonian fluids, and have apparent viscosities considerably higher than those of either constituent phase. The high apparent viscosity of foam with its concomittant effect on mobility ratio and sweep efficiency no doubt prompted several attempts by research groups to use foam as a displacing agent in porous media. Based on recent experience, most of these groups probably succeeded in completely blocking fluid flow in the porous media and then abandoned their efforts. Two groups apparently found the successful combination of experimental parameters at about the same time.3,7 Others have recently added to our knowledge of foam flow in porous media and its use as a displacing agent.8-13 An experimental problem encountered by Fried3 was a transient blockage of foam flow in porous media when distilled water was used to prepare the foam-producing solution. Fried surmised that this was due to an electrokinetic effect and he eliminated it by using electrolytes in preparing foaming solutions. He also measured the streaming potential of a number of foams in capillary tubes which he found to be appreciably higher than those obtained when the constituent liquid flowed under comparable conditions. This paper presents results of a more comprehensive study of the streaming potential generated by aqueous foam flowing in both open and packed Pyrex tubes. It also adds to knowledge of the rheology of these foams as deduced from their flow behavior in open tubes. APPARATUS AND PROCEDURE A diagram of the apparatus used is shown in Fig. 1. Details of its construction, testing and use are described elsewhere.14 Careful selection of materials, extreme cleanliness and rather elaborate electrical insulation and shielding were necessary to obtain reproducible results (±5 percent). Both streaming potential and streaming current were measured with an electrometer. The design of the foam generator developed for this work is novel (Fig. 2). It will produce uniform fine-textured foams at pressures sufficiently

By J. Chipman, H. Towers, M. Paris

A simple radioactive tracer technique is used to measure the diffusion coefficient of calcium ion in molten slags. In a slag of 40 pct Ca0-40 pct Si0,-20 pct Al203, Dc " at 1450°C is 1.3x10-6 cm&apos; sec-&apos;. THE application of the principles of thermodynamics to steel and iron making problems has proved so fruitful that the kinetic approach has tended to be neglected. It seems probable that in some reactions the rate-determining step is the dif-fusivity of the reactants or of the products. But knowledge of the diffusion coefficients of the constituents of liquid slag and metal is singularly lacking. The present work was undertaken as a first step toward supplying such data for slags. Furthermore, any additional information on the physical properties of liquid slags might be expected to help in elucidating their structure. It is essentially a preliminary investigation, the course of which was determined more by the necessity of establishing a method than by the immediate intrinsic interest of the results. For example, the selection of calcium ion to be studied was dictated by the suitability of the isotope Ca45 in that it is a simple emitter with a long half-life. Of the other ions commonly encountered in slags, the isotopes of iron and manganese have relatively complex radiations as well as the normal disadvantage of requiring control of the oxygen potential of the atmosphere; Mg27 and Al29 have half-lives measured only in minutes; Si3&apos; has a simple decay process but its half-life of 2.8 hr is too short for preliminary studies; the only useful oxygen isotope is the stable O18; and there remain only sulphur and phosphorus both of which have suitable isotopes but were rejected as being of less fundamental interest than calcium. Similarly a lime-alumina- silica slag was used in preference to calcium silicate primarily because of its low melting point and its capacity to form a glass on fairly rapid cooling. Literature Review Very few studies of diffusion in liquid silicate systems have been reported. In order to determine the origin of diopside inclusions in felspathic rocks, Bowen1 investigated the diffusion between diopside and various mixtures of albite and anorthite. Platinum crucibles were used with diopside, the heavier of the two liquids, forming the lower half of the cell and diffusion taking place against gravity. Change in concentration along the diffusion path was found by measuring the refractive index of the quenched glass. Nearly thirty years later McCallum and Barrett2 used essentially the same method to determine the diffusion coefficient of lime in lime-alumina-silica slags. In this case the interest was to find the rate-determining step in the process of slag attack on refractory materials. In an investigation of the kinetics of the sulphur reaction, Derge, Philbrook, and Goldman8 determined the diffusion coefficient of sulphur in a typical blast furnace slag by the simple procedure of melting a slag containing 2 pct S over an identical slag sulphur-free. They make no claim to a high degree of accuracy but suggest that D, is of the order of 10-6 cm2 sec-l. Other high temperature liquid diffusion studies have been concerned with metals. Holbrook, Furnas, and Joseph4 determined the diffusion coefficients of silicon, phosphorus, sulphur, manganese, and carbon in liquid iron by immersing a small carbon crucible containing pure iron-carbon alloy in a large vessel containing iron with a high concentration of the particular element. Their results were confirmed by Paschke and Hauttmann5 using a similar method. Diffusion coefficients in silicates in the glassy state have been studied by Johnson, Bristow, and Blau6 Both Na24 and Ca45 were used as tracers but only the

Jan 1, 1954

By F. T. Selleck, H. H. Reamer, B. H. Sage

An experimental investigation was made of the effect of temperature upon the three-phase pressure associated with the propane-water and propene-water systems when hydrates were present. In addition, the characteristics of the propane-propene-water system were established over a limited range of ternperatureo under conditions such that hydrate was formed. The hydrate phase for this system may he a solid solution and the distribution of propane and propene in it is similar to that found in the coexisting hvdrocarhon liquid phase. INTRODUCTION A knowledge of the characteristics of hydrates of the hydrocarborrs encountered in industrial practice is of importance in connection with the design of process equipment. Villardl.1,2 carried out early studies of hydrates, and de Forcrand1 con-sidered the more probable compositions of the hydrates of hydrocarbons. Hammerschnid1 presented information about the propane-water and the isobutane-water systems. Scheffer5 studied the hydrate of hydrogen sulfide in detail, and de For-crand reported on the hydrates of krypton, argon, and xenon.1 Roberts and co-workers1,2 determined the nature of the hydrates formed in the methane-water and ethane-water systems. Carson and Katz10 studied the methane-propane-water, methane-pentane-water, and the methane-hexane-water systems in the four-phase region. The results of this rather extensive investigation indicated that the paraffinic hydrates formed solid solutions. The experimental evidence now available does not Support the existence of hydrates of the pentanes-antl-heavier hydrocarhons but it cannot be stated with certainty that such hydrates are not formed. Stackelherg. 11,12,13 made extensive studies of the crystal structure of paraffinic hydrate; by means of x-ray techniques and found that hydrates poses; a definite structure and composition. The existence of such a Structure does not preclude the firmation of Solid solutions of hydrates in aqueous systems containing two or more hydro-carbon~. Wilcox, Carson and Katz" reviewrd the information on the hydrates of importance in the processing of natural gas and presented data concerning their formation from natural gas. Kobayashi and Katz1&apos; made studies at high pressure of the Hydrate of methane. and Unruh and Katz"&apos; investigated hy-drates in mixtures of carbon rlioxide and methane. Frost and Deaton contributed to the knowledge of the composition of the paraffinic hydrates The irregularities in the experimental results were several times the expected uncertainties. This experience confirms the behavior encountered by other investigators indicating that hydrates tend to occlude water during their formation, thus rendering difficult the direct measoremeut of their composition. Miller and Strong2 investigated a number. of paraffinic hydrates from the standpoint of their possible application to (, the industrial storage of gas. Powel1 studied the effect of solutes upon the decomposition temperature of paraffin hydrates. Marked lowering of the decomposition temperature at a given pressure may he obtained by the use of such additive agents as ethylene glycol, urea. and sodium chloride. APPARATUS AND METHODS Two method* were here employed to study the behavior of hydrates. The first involved a glass capillary within which the hydrocarbons and water were confined over mercury. The second made use of a double-ended weighing bomb technique." The glass capillary equipment has been described elsewhere.&apos;" A schematic drawing of it is presented in Fig. 1, where the arrangement of the agitator and mercury reservoir is shown in some detail. The lower part of the glass capillary, D, was enlarged to afford space within which the fluids used in the investigation could he stored at low pressures after their introduction through the valve. G. The temperature of the capillary was controlled by the circulation of a hydrocarbon oil of low viscosity from the agitated bath, B, through the vacuum jacketed column. C. The pump, A, was employed for the circulation of this oil. A relatively clear view of the capillary tube, D, was obtained through the vacuum jacket. Mercury was introduced into the lower part of the vessel, E, from

Jan 1, 1952

By H. N. Mead

In a reservoir when gas comes out of solution and rises, additional pressure is created because of the change in position of this gar in the bounded volume. If this pressure effect is not taken into account as a pseudo-influx ill mate rial balance calculations on reservoirs in which there is evolving gas, an error is introduced that is directly proportional to the length of oil column and amount of gas evolved and inversely proportional to the reservoir pressure. In reservoirs with small oil column this pseudo-influx is of little importance. The larger the oil column the more important the effect becomes. The most important application, however, will be for reservoirs with declining pressure in which increasing water entry has been indicated by material balance calculations. It could be that this indication is the result of the cited pseudo-influx and not water entry at all. This paper attempts to explain this phenomenon in relation to material balance calculations and prevents an approximate method of determining tile pseudo-influx. INTRODUCTION Only recently has the pressure-volume relationship of gas rising in a liquid appeared in engineering literature, although its effect has been discussed for several years—especially among engineers engaged in drilling operations. The writer published a paper in 1957 in which this phenomenon was examined in relation to blowouts in drilling wells.&apos; Also, in 1957 Stegemeier and Matthews&apos; authored a paper in which the relationship was presented with respect to pressure build-up tests when shutting in producing wells. In this paper the effect will be called "pressure inversion" which is descriptive of the phenomenon. Fundamentally, the effect just mentioned is the result of changing the position of a quantity of energy contained within the gas itself (as a result of its compression) within the bounded volume in which the gas exists. If the gas were allowed to expand "beyond all bounds" there could be no pressure inversion effect. This is because all of the energy contained within the gas as a result of compression would have been re- PRESSURE INVERSION A phase that has not been discussed in the literature is the effect of pressure inversion upon material balance calculations in reservoirs in which the reservoir pressure drops with reservoir withdrawal and is below the bubble point. This action releases solution gas which, after the critical gas saturation has been reached, will tend to rise and collect at the top of the reservoir. The pseudo-influx caused by this effect could be great enough in reservoirs of large oil column and high permeability to render invalid any analyzer studies made on them — if pressure inversion has not been taken into account. Most suspect would be those reservoirs with large oil column in which increasing water entry has been predicted but the bottom wells have not yet produced water. Example 1 Simply stated, this phenomenon exists in oil reservoirs because of the difference in density and expansibility between gas and oil. For example, if a bubble of gas exists at the bottom of a 1,000-ft column of oil having a gradient of 0.30 psi/ft with the pressure at the top of the column zero, the bubble of gas will be compressed to a pressure of 300 psi. If temperature and the combined volume of the oil column and the gas bubble remain constant, as the gas bubble rises in the oil column it will have the same volume and consequently the same pressure at any point. Under these conditions when thc bubble reaches the top of the oil column, the pressure will be approximately 300 psi at the surface and approximately 600 psi at the bottom of the oil column. If it is assumed that the oil is incompressible the pressures will be exactly 300 and 600 psi, respectively.

By Wilfred Walker

With the advent of the New Global Tectonics a coherent pattern of geology is emerging. To the economic geologist this is of vital concern because the type of mineralization in particular environments is predictable. Developments in geological reasoning now take their place beside developments in geochemistry and geophysics. Much is known of the worldwide geography of the Alpine orogenic period because it is now ending its 200 million years of existence, starting with the Jurassic, and we can see the mid-ocean rises and the down flow zones, and between them the stable oceanic and continental platforms. The concepts of mantle cells, the spreading sea floor, and continental drift have gained general acceptance. The oceanographers have demonstrated the uprises like that in the mid-Atlantic. In this paper it is suggested that down flows in the oceans are marked by island arcs, like the West Indies; and down flows in the continents are marked by orogens like the American Cordillera. The number and position of mantle cells is controversial: a total of about 16 cells is suggested in this paper. Certain cells expand, and as they carry continents with them give rise to concepts of plate tectonics. Specific types of mineral deposits are associated with the uprises, oceanic and continental platforms, and down flows. The uprises are accompanied by the currently described Red Sea and Salton Sea deposits, the oceanic parts of the platform have the nodular deposits, and the continental platforms have the post-tectonic deposits. However, most economic metal deposits are associated with the down flow zones in which the stage of geosynclinal development controls the type of deposit: (1) In the initial development stage the simatic upper mantle may be tapped and give rise to the volcanogenic massive base metal sulfide deposits and to the ophiolite suite which characteristically carries nickel, chrome, and cupreous pyrite. (2) In the early geosynclinal stage sialic crust is driven down into the simatic magma of the upper mantle and basic to acidic differentiates give rise to stocks accompanied by skarn and hydrothermal deposits. (3) The intermediate stage of geosynclinal development gives rise to tin-tungsten, lithium, and beryllium deposits as the magma chamber rises above the level of the upper mantle and there is no simatic component. (4) The late stage is one of regenerated deposits. The porphyry deposits are not restricted to stages but only by the time of generation of acid magma. As the geosynclinal system dies, the mantle is again the source of magma, giving rise to gabbro and diabase dykes and sills: in this last, post-tectonic, continental platform environment are found the Mississippi Valley type lead-zinc deposits, the Blind River and Witwatersrand type of sedimentary uranium and gold deposits, and also Sudbury&apos;s nickel. The key relationship of major ore deposits generated by downflows is depicted herein on a framework of uprises, platforms, and downflows in the Alpine orogenic period. There is evidence for nine orogenic periods, of which the Alpine period is the latest, having taken place from 3500 million years ago to the present. Each period was characterized by its own worldwide mantle cell system and associated uprises, platforms, and down flows. The cycle of geosynclinal development, including corresponding cycles of mineralization, can be precisely defined in relation to each of these orogenic periods. The development of the Alpine orogenic period therefore can be used as a guide to the study of the earlier orogenic periods which comprise well known periods: Kenoran, Hudsonian, Grenville, and Paleozoic; and less well known: Konkian, Aulian, Belomorian, and Elsonian [(Table 1)]. Each name is used for the period as a whole, and not for the main orogenic event.

Jan 1, 1973

By G. R. Purdy, J. A. Malcolm

The isothermal dendritic precipitation of y in p CuZnSn is compared with the isothermal formation of Widmanstatten a plates in p CuZn. Although both precipitates are evidently bounded by semicoherent interfaces, the dendritic shape of y evolves through smooth "sinuoidal" shape perturbations, while a-p interfaces tend to be strictly planar, or rnicroscopically faceted. An estimate of the average inter-facial free energy of cube-oriented y in p through the Mullins-Sekerka analysis indicates that it is low (of the order of 50 ergs per sq cm). Interface mication is apparently controlled by volunle dij&apos;usion, and the observed anisotropy in growth probably results from anisotropy of inter facial free energy. Studies of the grain boundary precipitation of y in p indicate that the precipitate can grow in both $ grains, but becomes unstable with respect to the grain with which it shares a mobile semicoherent interface. Facets observed at the tips of Kurdjumov-Sacks-oriented Wid-manstatten a plates correspond to variants of an irrational hahit, near (231)0. Comparison with Hu and Smith&apos;s determination of relative interfacial free energies of a-(3 boundaries suggests that this system possesses an extremely deep o cup, which results in an ej&apos;ective low-o zone. The possible effects of such a cup on the stability of a-p interfaces are discussed, a needles, grown during rapid continuous cooling, possess microscopically smooth interfaces, and are characterized by a high degree of&apos; damage in the region of the boundaries. These boundaries, induced to move on tempering at 200"C, become faceted as equilibrium is approached, which seems to indicate that boundary structure and mobility in this system are dependent on the local degvee of departure from equilibrium MULLINS and sekerkal have elucidated the phase boundary stabilizing effect of surface tension. a factor not taken into account in previous treatments of morphological development. Their analysis applies to the isothermal growth of a pure spherical precipitate (planar in the limit of infinite radius) in a slightly supersaturated solution, under conditions of inter-facial local equilibrium and isotropy of interfacial free energy. More recently, several other factors which might tend to stabilize planar interfaces have received attention. These are: i) interface diffusion;4"8 and ii) slow interfacial reaction. cahn7 included a slight anisotropy in interfacial free energy, and showed that it has no stabilizing effect, but forces shape perturbations to reflect the anisotropy. shewmon4 noted that dendritic morphologies are rarely observed in solid-solid systems, and, in particular, postulated that slow interfacial reaction occurs at all boundaries between proeutectoid ferrite and austenite, except those which propagate parallel to {11 l)y planes (for Kurdjumov-Sachs [K-S] related phases). Previously, Aaronson~ had proposed interfacial reaction at the broad faces of Widmanstatten plates, and expected that the lateral motion of high-mobility incoherent ledge edges would produce planar precipitates bounded by law-mobility semi-coherent interfaces. The problem of interfacial reaction during the dif-fusional formation of precipitates has often been ignored, although it is apparent that a small component of chemical reaction must exist at any moving interface." Further, all solutions of the diffusion equations for boundary conditions corresponding to isothermal growth predict infinite growth rate at time zero, so that elements of interfacial reaction would be most easily detected at early times. However, reported deviations from diffusion control are comparatively rare," and the local-equilibrium diffusion-control model appears adequate for the description of many isothermal growth systems.&apos;2"9 Cahn14 has treated the problem of migration of an interface which is able to reach positional energy minima, and concluded that such an interface, if subjected to a high local ther-modynamic "driving force", may migrate normal to itself without the benefit of ledges. As local equi-

Jan 1, 1968