Search Documents

By C. N. J. Wagner, E. N. Aqua

Dilute Fe-Si alloys (0 to 5 wt pet Si) were cold-worked by making filings at room temperatuve. The analysis of the broadening of the X-vay powdev pattern peaks yields anisotropic particle sizes normal to the (110), (100), and (112) planes which are a consequence of deformation faults (probability a) and twin faults (probability p). The combined fault probability (1.5a +ß) increases from 0.01 in pure iron to 0.02 in Fe-5 pct Si. The root mean square stvains vary with crystallographic ovientation due to elastic anisotropy of the alloys, and increase from about 0.0035 in pure iron to 0.005 in Fe-5 pct Si measured in the [100] direction. Assuming that deformation and twin faults occur with equal probability, the X-ray data would imply that the stacking-fault energy does not change upon alloying. THE crystallographic aspects of the plastic deformation of dilute Fe-Si alloys has been studied many times since the observation of glide band structures by Barrett et a1.l These glide bands were much straighter than the wavy bands observed by Gough2 in unalloyed iron nearly 40 years ago. This difference in the morphology of the slip band structure has been verified many times, most recently by replication electron microscopy3 and dislocation etch-pitting methods.4,5 These observed differences in deformation behavior have been considered to result from the degree of cross slip that occurs in pure iron and in the Si-Fe alloys. The lowered tendency for cross slip would result from a lowering of the stacking-fault energy of iron by the silicon alloying addition. Experimental evidence for this lowered stacking-fault energy in the Si-Fe alloys, obtained with transmission electron microscopy, is the observation of dissociated dislocations in Fe-6 pct si6 and Fe-3 pct Si alloys,7 and the observation of sharply defined cellular substructures in Fe-3 pct si6,7 compared to the more diffuse substructure in zone-refined iron.' The activation energy for recovery of cold work is greater in the Si-Fe alloys than it is in pure iron, indicating that cross slip has become a more difficult process.9 The purpose of this investigation is to determine the change in stacking-fault probability from the broadening of powder pattern peaks in dilute silicon-in-iron solid solutions, when cold-worked at room temperature. The knowledge of the stacking-fault probability and the dislocation density, both of which can be deduced from line-broadening analysis of two orders of reflections from (110), (200), and (112) planes, will permit us to calculate the change in stacking-fault energy upon alloying silicon into iron. Previous X-ray investigation of cold-rolled Fe-5 wt pct Si (100)[001 ] single crystals did not reveal any line broadening, whereas cold-rolled Fe-3.1 wt pct Si (001) [110] and (001)[100] single crystals10 showed line bro2dening as a consequence of small particle sizes (-200A) and root mean square strains (-0.25 pct), which are comparable to those found in cold-worked iron filings.11 EXPERIMENTAL PROCEDURE A series of five Fe-Si alloys containing nominally 1 to 5 wt pct Si and pure iron were cold-worked by making filings at room temperature. The actual silicon content deviated at the most by +0.1 pct which is of no significance in the present study. The carbon contents of these materials were less than 0.02 pct. The X-ray diffraction patterns were measured with molybdenum, cobalt, and iron radiation using a GE and a Philips diffractometer. The (110)-(220), (200)-(400), and (112)-(224) pairs of reflections were

Jan 1, 1968

By J. L. Gillson

THE big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part1-15 in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits;'"= and some have made classical Studies3,4,21-27 introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the higest peak in the range. The finer grained and lighter colored rock is called the White-face, after another mountain appropriately named for a cliff colored by this facies of the anorthosite. In explaining the genesis of the ores the authors have reached no general agreement, but all consider them to be dominantly the result of magmatic processes rather than the result of replacement by pneu-matolytic or hydrothermal processes. However, in the conclusions of two authors, Osborne27 and Ste-phenson," the reader is told positively that the ore minerals were introduced after the wall rock was solid and also that the oxides are later than the silicates. This seems to mean that the ore came in as a later intrusion, like a dike, since Osborne speaks of filter pressing and later injection of a residual magma. Stephenson agrees in general with Osborne but disagrees with his conclusion that ore does not grade into country rock. Singewald22 calls in "mineralizers" to participate in magmatic deposition. Stephenson ends his paper with a statement that replacement was the dominant process for the introduction of ore with anorthosite. Hence both Singewald and Stephenson call on pneumato-lytic or hydrothermal processes to supplement magmatic crystallization from a silicate melt, but they cannot quite bring themselves to state that the orebodies formed in that way. In their conclusions the ores are still magmatic segregations and magmatic injections and—almost as an afterthought— "replacements." According to Bateman18 there was a gravitational accumulation process of the iron silicates and oxides, which were injected later. Rambere explains the ores entirely on physical-chemical theory, as does Evrard.17 Buddington and associates,10 in a paper presented to the Geological Society of America in 1953, believe the facts observed prove that the magnetite-ilmenite formed at magmatic temperatures. The present writer's conclusions, given here, were first presented in 1947 in Industrial Minerals and Rocks.= Since the papers of Ramberg, Bateman, and Buddington, published after 1947, gave no recognition to those conclusions that differ from their own, the writer has taken an opportunity to restudy the area in the field, and to examine a number of microscopic sections, and now presents the evidence more thoroughly than he had an opportunity to do in the

Jan 1, 1957

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By R. W. Parsons, P. R. Chaney

Oil recovery by the imbibition mechanism can be important in fractured carbonate reservoirs with a bottom water drive. Laboratory experiments were performed on water-wet carbonate rocks to model this process. The results are interpreted in light of the applicable scaling laws. The imbibition production behavior of a pillar of rock subjected to a slowly rising water table can be synthesized from data on total immersion experiments on small rock samples. If the rate of water table rise is slow enough and if the physical properties are such that the imbibition zone is of a small vertical extent, then only the final oil recovery on the small samples need be known. Applying laboratory imbibition data to a real reservoir should be done with caution because of possible wettability problems and the unknown behavior of two-phase flow in fractures. INTRODUCTION The spontaneous taking up of a preferential wetting fluid into a porous medium with the simultaneous expulsion of the contained fluid is termed imbibition. One of the many physical imbibition processes is the production of oil by the taking up of water into a water-wet reservoir rock. In certain types of heterogeneous reservoirs, e.g., fractured, it is realized that imbibition alone may be the dominant mechanism. Theoretical studies of imbibition oil recovery have followed several lines of attack. The behavior of certain mathematically tractable and conceptually simple models have been analyzed. Birks1 considered a bundle of vertical capillaries model, while Perotti et al.2 and Kelemen3 used a model of a series of vertically oriented fractures. If the oil production behavior from a block of reservoir rock is known, then the cumulative behavior of a vertical stack of these blocks subjected to a rising water table can be determined by a method outlined by Aronofsky et al. 4 Knowing the capillary pressure and relative permeability functions should uniquely set the imbibition behavior for a given sample. Solutions of the partial differential equations describing the process, however, present some formidable problems. Digital computer techniques have been applied to displacement processes in which the capillary pressure has been included.5"8 More recently, similar techniques have been used by Blair 9 to calculate countercurrent imbibition behavior. The fact that imbibition behavior is described by the usual fluid flow equations (Darcy's Law and continuity equation) implies that the derived scaling laws should apply equally to this situation. Use of model experiments to study imbibition has been employed by Graham and Richardson 10 and Mattax and Kyte,11 who actually tested the scaling law applicability. This study is concerned with scaled model imbibition experiments on water-wet carbonate rocks. Of particular interest is the slowly rising water table experiment. This simulates a highly fractured reservoir with the water table rising uniformly through the vertical fracture system. Experiments were performed on different sized samples and with different rates of rise of the water-oil interface surrounding the rock pillar. Total immersion imbibition experiments on smaller rock samples were performed to test the basic linear scaling laws and to see if these simpler tests could be used to synthesize the rising water table experimental results. THEORY IMBIBITION SCALING LAWS Scaling laws for the flow of two incompressible immiscible fluids in a porous medium have been presented by Rapoport.12 These are derived directly from Darcy's Law for the individual phases and the continuity equation. Results from a laboratory model experiment will duplicate those from some reservoir prototype if a constant proportion is maintained among the three forces acting on the fluids — the capillary pressure gradient, the gravitational gradient and the flowing pressure gradient. Operation of the model (i.e., fluid injection or withdrawal) must be conducted in accordance with specific equations. If the

Jan 1, 1967

By T. E. Seidel, A. U. MacRae

The dependence of the electrical and crystalline properties of silicon containing ion implanted boron atoms have been studied as a function of the incident dose, substrate temperature, and annealing tempera-ture. Hall effect studies show that the compensation due to defects is negligible after annealing at and above 500°C for a dose of 1013 ions per sq cm. Steps occur in the isochronal annealing curve for the sheet resistance at 300°C and 800°C and the mechanisms responsible for these steps are discussed. The range of the ions at 150 kev is 3500 * 5001. Electron diffraction studies on samples implanted with 150 ker ions show the existence of damaged (polycrystalline) silicon closer to the surface than the range of the ions. Etching and subsequent annealing of etched and unetched specimens suggest that the poly crystalline silicon is closer to the surface than the bulk of the distribution of ions. THE purpose of this study is to investigate some electrical and crystalline properties of ion implanted boron in silicon. Sheet resistance, Hall measurement, depth distribution by chemical staining, thermal probe and electron diffraction have been used to study the properties of samples implanted in a random direction with ions having energy up to 150 kev. The boron-silicon system has been the subject of considerable study'-7 due to its possible application in the fabrication of electronic devices. The implanted ions produce considerable crystalline damage to the substrate crystal before they lose most of their primary energy and come to rest. Fortunately, most, if not all, of this damage can be removed by subsequent annealing or by holding the substrate at an elevated temperature during the implantation process. Sheet resistivity measurements of the p-type layers produced by boron implantation into room-temperature silicon, reveal that the annealing occurs in a two-step process: the first occurring at -300°C and the second at -800°C.' Electron-microscope and low-angle electron diffraction studies of this damaged material indicate that the bombarding ions produce an amorphous silicon region about the trajectory of each ion.' At high doses, these damaged regions overlap and an amorphous surface layer results. Furthermore, the 800°C annealing step, appears to be associated with the elimination of this gross damage. The depth distribution of the as-implanted and also the annealed samples have been studied by an angle lap and staining technique as well as by Hall measurements.3-7 We find the experimentally determined ranges of the boron are less than those calculated by the Lindhard-Scharff-Schiott theorys (hereafter referred to as the LSS theory). Our results are in essential agreement with pre- vious results. In addition, we have made Hall measurements on samples bombarded with a low dose (2 x 1013 ions per sq cm) to minimize impurity banding effects, and find that deep ionized levels influence the carrier concentration and room-temperature hole mobility until the sample is annealed at temperatures above 500°C. Above this temperature, the data corresponds to that obtained when silicon is doped with boron by conventional techniques. We have also made a depth distribution determination of the crystalline damage due to the implanted boron by using glancing angle electron diffraction techniques. It was found that the gross damage depth distribution of heavily implanted samples is closer to the surface than the depth distribution of the electrically active boron. By removing this gross damage, without affecting the distribution of the implanted boron, we have determined that the 800°C annealing stage is not exclusively due to the improvement in the crystalline perfection of the amorphous material but also appears to be associated with the annealing of some point defects. These results and their relation to previous results are discussed in the following sections. IMPLANTATIONS Boron ions were implanted into silicon samples using an accelerator capable of operating from 10 to 150

Jan 1, 1970

By D. C. Jillson

WORK in recent years1-' has indicated a complexity of the processes of deformation of metal crystals not previously appreciated and not fully accounted for by any hypothesis so far advanced. Furthermore, the nature and mechanism of formation of nuclei of recrystallization have not been determined precisely. The deformation of single crystals of zinc has been studied frequently, but the purity of the zinc and the perfection of the specimens sometimes have been given little consideration. Methods have been developed recently that readily yield zinc single-crystal specimens of high quality.5 In the present work, such specimens were deformed in various ways under various conditions, and deformed specimens were annealed to obtain information regarding recovery, recrystallization, and grain growth. The paper attempts to correlate and evaluate previous data, as well as to present new data, in order to determine areas in which more detailed work might be done most profitably. Tests at temperatures from the freezing point (419.46°C) to room temperature revealed glide only on basal planes in a close-packed direction (100)*, as reported by Mark, Polanyi, and Schmid6 and others. Markings probably similar to those observed by Kolesnikov7 and Boas and Schmid8 were noted in specimens stretched at elevated temperatures, but it seemed clear that these were not caused by prismatic or pyramidal slip (see second paragraph of section on Phenomena Involving Bending of the Basal Plane). Twinning Twinning on the octahedral plane of a face-centered cubic metal has been pictured as a process of simple homogeneous shearing along that plane in a [112] direction. It was recognized by Mathewson and Phillipsv and others""" that the (102) twinning of zinc required a somewhat more complex mechanism and might be considered as a homogeneous shearing of (102) planes in a [211] direction plus slight adjustments of atoms to positions of greater stability or lower energy, or as a single movement of each of the atoms in the same sense into the final positions. Gough and Cox" modified Mathewson's mechanism to obtain a more stable lattice configuration, but it is not clear that they succeeded, and their mechanism requires movement of some of the atoms in a sense opposite to that of the overall twinning movement. They also suggested that twinning may occur as a result of previous basal slip. This conclusion was based on the observation that twinning caused by alternating torsion was clearest and most profuse at positions for maximum basal slip rather than for maximum stress on (102) planes in the close-packed direction (not the twinning direction), and no mechanism was described. It might be wondered whether resolution of stresses on the twinning plane in the twinning direction would have afforded a simpler explanation. If twinning is essentially a simple homogeneous shearing along the twinning plane, it would seem that twins should grow by a smooth, continuous mechanism, and, indeed, that a simple reversal of stresses should reverse the shearing and de-twin the crystal. Cylindrical tablets 1/8 to 1/4 in. thick were cleaved from singlle-crystal specimens and were squeezed, perpendicular to a second-order prism plane, to give a tensile stress perpendicular to a first-order prism plane. A "click" was heard and a thin, needle-like twin appeared on the basal cleavage face. If squeezing was continued smoothly, the twin, viewed at magnifications up to X500, grew smoothly and quietly (fig. 1). X-ray examination verified that the twinning was of the (102) type. Rotating the compression axis 90" to reverse the stress then caused a smooth, continuous shrinkage and ultimate disappearance of the twin (fig. 2). The squeezing also caused a rumpling of the basal

Jan 1, 1951

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.'-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc's were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By H. I. Kaplan, C. Laird

Pulsating contpresslon experiments have been carried out on coppev single crystals in order to test the adequacy of mechanisms which have been suggested for stage I cvack grouth when tension-compression loading is the mode of- applying stress. Although dejorrrzation continues slowly for many millions 01 cycles under Pulsating compression stresses both within slip bands formed in the first cycle and by the creation of new bands, the morphology of these bands is not typical of fatigue slip bands in general and neither initiation of cracks nor propagation of artificially induced cracks was observed. It is therefore concluded that 1) initiation and growth of cvacks in fatigue is a consequence of repeatedly reviersed, microplastic deformation rather than intermittent, unidirectional deforma-tion, 2) gvowth of- cracks in polycrystalline specimens FAILURE of a plain specimen subjected to cyclic tension-compression stresses is known to take place by two stages of cracking.1,2 The first stage is characterized by propagation along slip planes roughly at 45 deg to the stress axis, in the outermost layers of the specimen, and at a rate of the order of angstroms per cycle. The average macro orientation of a stage I crack is normally at right angles to the stress axis,3 however, except in a few cases, e.g., single crystals in suitable orientation, when both the micro and macro directions of propagation are at 45 deg to the axis. After a stage I crack has penetrated to such a depth that the stress on the remaining section of metal is significantly increased, stage II crack propagation succeeds stage I, at right angles to the stress axis both micro and macroscopically. Direct evidence of the processes occurring during a subjected to pulsating compression stresses is caused by the setting-up of local tensile stresses due to interactions between grains, and 3) both unslipping mechanisms and operation of the "plastic blunting process " within a single slip band are adequate descriptions 01- stage I growth, being fundamentally similar. The slip mode of a material, however, is considered to control whether unslipping or the plastic blunting process takes place. Thus materials of planar slip mode fauor unslipping while those hacing a wavy mode, and capable of cross slip, can fail in stage I by the plastic blunting process. Similarly, and perhaps more importantly, reversed torsion and tension-compression modes of applying stress may be expected to cause the unslipping mechanism and the plastic blunting process, respectively. single stress cycle4,5 shows that stage II crack propagation takes place by a repetitive plastic rounding and closing of the crack tip. This mechanism has come to be called the "plastic blunting process".6 On the other hand, the extreme smallness of the phenomena occurring in stage I growth prevents elucidation of its mechanism by direct observation. Many suggestions have been proposed for this mechanism,'"-" most of them involving some kind of random or systematic unslipping process. It is possible, however, that the mechanism of stage I growth is essentially the same as that of stage 11, but occurring on a much smaller scale.6 In this situation, it has been observed that cracks propagate along slip bands comprising dislocation cell structures and bounded on either side by regions of different dislocation density and distribution." Since there is evidence that such bands are softer than their matrix, * it may be expected that the plastic blunting process occurs within a single slip band during stage I growth, rather than on two gross bands as in stage 11, when the acting stress is greater.= The blunting of the crack tip allowed by coordinated

Jan 1, 1968

By L. W. Holm

This study shows that in the presence of foam, gas and liquid flow separately through porous media representative of reservoir rock. These results were obtained by using tracer techniques to measure the flow of the gas and liquid comprising the foam. Foam does not flow through the porous medium as a body even when the liquid and gas are combined outside the system and injected as foam. Instead, the liquid and gas forming the foam separate as the foam films break and then re-form in the porous system. Liquid moves through the porous medium via the film network of the bubbles and gas moves progressively through the system by breaking and re-forming bubbles throughout the length of the flow path. The flow rates of the gas and liquid are a function of the number and strength of the films in the porous medium. There is no free flow of gas; i.e., no continuous gas phase. On the basis of these results, foam can be expected to improve a water flood or gas drive by decreasing the permeability of the reseruoir rock to a displacing liquid or gas. This improves the mobility ratio and thus the conformance of the flood. INTRODUCTION Foam is formed when gas and a solution of a surface active agent are injected into a porous medium either simultaneously or intermittently. During the past few years, several papers have been published on the subject of foam flow in Dorous media. Foam has been used successfully in the removal of capillary water blocks from producing formations.''2 The use of foam in gas storage reservoirs to reduce gas leaks and to increase storage capacity has been considered in recent years. Foam has also been investigated as an oil displacing agent,3-5 and as an agent to improve the mobility ratio in a waterflood.6-10 However, the mechanism by which the gas and liquid phases comprising the foam flow through a porous medium has nor been described adequately. Normally, when two immiscible phases (gas and liquid) flow concurrently through a porous medium, each phase follows separate paths or channels. At given saturations of the two phases, a certain number of channels are available to each phase, and as saturations change, the number and configuration of the channels available for each phase also change. The effective permeability of each phase is a function of the saturation of that phase only, and the flow of each phase can be described by Darcy's law. When foam is present, the effective permeability of the porous medium to each phase is greatly reduced compaced with permeabilities measured in the absence of foam.6,11-13 Based upon the observed flow of surfactant solutions and gas in capillaries, it has been concluded that the gas and liquid may flow separately or they may flow combined as foam. At least four mechanisms have been postulated to explain how fluids flow with foam present: 1. A large portion of the gas is trapped in the porous medium and a small fraction flows as free gas, following Darcy's law.9 2. The foam structure moves as a body; the rate of gas flow is the same as the rate of liquid flow. 6,13 3. Gas flows as a discontinuous phase by breaking and re-forming films. Liquid flows as a free phase.12 4. A portion of the liquid and gas move as a foam body while excess surfactant solution moves as a free phase.14 It also has been suggested that different flow mechanisms exist for high quality (dry) foams made from dilute surfactant solutions and for foams made from more concentrated solutions. Studies conducted on the flow of foam through capillaries have shown that a plug-type flow occurs and that foam flows as a body.6,15 Fried also has described the flow of foam through porous media as

Jan 1, 1969

By J. C. Melrose

The contact angle is one of the boundary conditions for the differential equation specilying the configuration of fluid-fluid interfaces. Hence, applying knowledge concerning the wettability of a solid surface to problems of fluid distribution in porous solids, it is important to consider the complexity of the geometrical shapes of the individual, interconnected pores. As an approach to this problem, the ideal soil model introduced by soil physicists is discussed in detail. This model predicts that the pore structure of typical porous solids will lead to hysteresis effects in capillary pressure, even if a zero value of the contact angle is maintained. The model is generalized to situations in which the contact angle takes on values between zero and 40 degrees. For the imbibition branch of the capillary- pressure function, the model predicts a considerable departme ftom the usually assumed cos 0 relationship. In fact, according to the model, it is possible that a displaced wetting phase will not be able to reimbibe, even when the contact angle does not exhibit hysteresis. INTRODUCTION The subject of capillarity in porous media has long been of interest in many branches of engineering and applied science. The earlier investigators were those concerned with the physics of soils. 1-5 More recently, petroleum engineers and others dealing with the problems of petroleum production from reservoir rock have given much attention to the subject.6-10 Also, important additions to the literature of capillarity have been contributed from the field of chemical engineering.11-12 These attest to the wide range of industrial applications in which capillary phenomena play a role. The present paper is concerned with the role which wettability plays in capillary action in porous media. As is well known, capillary-rise (or capillary pressure) phenomena have frequently been interpreted with the aid of a model employing the concept of a cylindrical capillary tube. This approach has enjoyed a certain degree of success in correlating experimental results.13 The generalization of this model, however, to situations which involve varying wettability, has not been established and, in fact, is likely to be unsuccessful. In this paper another approach to this problem will be discussed. A considerable literature relating to this approach exists in the field of soil science, where it is referred to as the ideal soil model. Certain features of this model have also been discussed by Purcel114 in relation to variable wettability. The application of this model, however, to studying the role of wettability in capillary phenomena has not previously been attempted in detail. In the present paper, additional features of the model are introduced. These features are critical in determining the quantitative behavior of the model. GENERAL FEATURES OF CAPILLARY HYDROSTATICS BASIC PRINCIPLES When the interstices of a typical porous solid are occupied by two or more immiscible fluid phases, the fluids are microscopically commingled. Hence, fluid-fluid interfaces are found within a certain fraction of the pore openings. The fundamental equation of capillarity specifies the configuration of these fluid-fluid interfaces. This is known as the Laplace equation, when derived from mechanics, and as the Gibbs-Kelvin equation when derived thermodynamically.15 Given two fluid phases, a and ß, in hydrostatic equilibrium, the Laplace equation states that the respective fluid pressures in regions close to the interface are related by Here oaß is the surface or interfacial tension and rl and r2 are the principal radii of curvature of the surface or interface. The pressure difference, Pa-Pß, is the capillary pressure, PC. As Buff15 has shown, Eq. 1 states the condition for hydrostatic equilibrium within the two-phase confluent region, which is referred to as the interface. It thus can

Jan 1, 1966

By D. P. Harris

The construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area is postulated. The questions (1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and (2) can this geology be related mathematically to mineral wealth and probability are answered in a case study of 97,000 square miles in Arizona and New Mexico. Measurements on mineral wealth and geologic variables of 243 cells were made. The geologic variables, valued in counts, percentages and lengths, quantified the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. The cells of explored area must be allotted the value class indicated by their cumulative production and estimate reserves (given well-defined geological relationships in a mineral wealth area), and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. This determines whether high value cells can be distinguished from low value cells by their geology as well as indicating those cells misclassified by the model into a higher value group than warranted by their known mineral wealth. The second use of the model is for extrapolation. It is demonstrated how geologic information on an explored area can be utilized in guiding exploration in an unexplored area. Exploration decisions can be predicted on explicitly determined measures of uncertainty (the probabilities). SUMMARY This study postulates the construction of a model to associate probability of occurrence of some measure of mineral wealth with the geology for each subdivision (cell) of the area. Such a model will distinguish those cells deserving further exploration on the basis of their geology: The basic postulates of this study are as follows: v = Q(R,S,F,A) P(V) = G(R,S,F,A,V), where V = a measure of mineral wealth P(V) = the probability of occurrence of V R = age and type of rock F = rock fracturing A =age of igneous activity and contact relationships. There are really two questions to be answered: 1) are the observations made in reconnaissance geology sufficiently related to mineral wealth to distinguish the cells of high value from those of low value, and 2) can this geology be related mathematically to mineral wealth and probability? In order to answer these questions, an area of about 97,000 square miles situated chiefly in Arizona and New Mexico was selected as a case study. This case study area was divided into 243 cells, each 20 miles square, and measurements were made on mineral wealth and geologic variables. Crude geologic variables valued in counts, percentages and lengths are constructed to reflect the above postulated variables. These measurement variables thus provide quantified values defining the theoretical concepts of the model. It was found that multiple discriminant analysis and classification analysis by Bayesian statistics and the multivariate normal probability function constitute a two-phase probability model that associates probabilities with geologic information and mineral wealth. Given the availability of an area that is well explored and upon which the relationships of mineral wealth to geology can be adequately defined, there are two ways in which the analysis outlined in this paper can prove beneficial. First, the cells of the explored area must be allotted the value class indicated by their cumulative production and estimated reserves, and a discriminant and classification analysis must be performed in which probabilities of the cell belonging to each of the value groups are generated as a function of the geologic variables. Such an analysis determines whether cells of high

Jan 1, 1967

The State Mining Experiment Station, Missouri School of Mines and Metallurgy, Rolla, Mo Charles H. Fulton, Director of the School of Mines Martin H. Thornberry, Director of the Mining Experiment Station. From the State Mining Experiment Station are issued all the general and technical bulletins of the School of Mines The latest bulletin containing a complete list of publications will be sent upon application to the Director of the Station Residents of the state may obtain bulletins as issued without charge, or may ask to be placed on the mailing list. Nonresidents should write to the Director for further information concerning specific bulletins. From the long list of bulletins the following have been care¬fully selected as being most likely to interest the geologist and the mining engineer. Vol 8, No. 1 (1916), Bibliography of concentrating ores by flotation, by J Cunningham, vol 1, No 3 (1912), Some apparatus and methods for demonstrating rock drilling and the loading of drill holes in tunneling, by L E Young, vol 2, No 1 (1915), Comparative tests of piston drill bits, by C R Forbes and L M Cummings; vol 2, No 3 (1916), Cupellation losses in assaying, by H. T Mann and C. Y Clayton; vol 4, No 1 (1917), The hydrometallurgy and electrolytic precipitation of zinc, by F D. James; vol 4, No 2 (1917), The effect of additional agents in flotation, pt 1, by M. H. Thornberry and H T. Mann, vol 5, No 1 (1919), The carbonization of Missouri cannel coals, by H L. Dunlap, K. K. Kershner and V. X Smiley. Vol 5, No. 4 (1921), Coal mining methods in Missouri, by W W Weigel, vol 6, No 1 (1921), The problem of the St Peter sand¬stone, by C L Dake, 50 cents, vol 6, No. 2 (1922), Bibliography on the electrothermic metallurgy of zinc, by B M. O'Harra, vol 6, No. 4 (1923), Experiments on the distillation of zinc from complex zinc-lead-silver ores, by B M. O'Harra and E S. Wheeler, vol 7, No 3 (1924), Underground loading devices, by C. E. van Barneveld, 81; vol 7, No. 4 (1924), Briquetting of zinc ores, by B. M. O'Harra; vol. 8, No 2 (1925), A treatise of Missouri clays, by M. H. Thornberry.

Jan 1, 1933

D. F. HEWETT, Washington, D. C. (communication to the Secretary*).-I am not prepared to discuss the metallurgical use of manganese in the form of alloys. In connection with other work for the U. S. Geological Survey, however, I have been investigating incidentally, for about 5 years, the American as well as other sources of manganese. There are some conclusions that come out of this investigation that may interest those whose greatest interest lies in the use of the alloys. From a geological point of view, most manganese ore deposits may be regarded as concentrated masses of manganese oxides, as there are few masses of the other manganese minerals that are rich enough in manganese and low enough in silica to warrant smelting. The deposits of the Huelva district, in Spain, which are largely manganese carbonate and silicate, are exceptions to this statement. Some deposits of manganese oxides, such as those of Russia and Cuba, are bedded with ancient sediments, and although they are clearly concentrated under unique conditions, the source of the manganese cannot be determined. Probably 60 per cent. of the world's production of manganese ore, or 95 per cent., if that of Russia be excluded, is derived from the superficial parts of deposits that have undergone weathering and enrichment near the surface. In other words, the situation with the manganese ore supply is such as it would be with regard to copper, if instead of being derived largely from deep zones of deposits of deep-seated origin, such as veins, it were derived solely from the zone of secondary enrichment. Manganese oxide occurs in all rocks but is most abundant in igneous rocks, of which, according to Clarke, it forms an average of 0.10 per cent. It also forms 0.05 per cent, of the average limestone, but only traces are present in shales and sandstones. It is interesting that although many commercially important manganese deposits occur in rocks that are but slightly richer in manganese than the average, the most important deposits occur in rocks of unusual character that are much richer in manganese than the average. Thus, the most important deposits of India and Brazil overlie or occur near masses of rocks that contain excessive amounts of manganese garnet and pyroxene.

Jan 5, 1917

By K. Leutwyler

The authors present an interesting review of various applications of rather well known theories. Their rearrangement of the original working equations is strictly computer oriented and serves well to that effect; however, the new appearance will be confusing to the slide rule-wielding members of the profession. In reviewing discrepancies existing between calculations made by Baker Oil Tools, Inc. field engineering staff members and computer output submitted based on the authors' program, the following error in concept was discovered in Eq. 4. The authors quote the length change due to helical buckling in the following form We appreciate Kurt Leutwyler's awareness of Archimedes' principle, and concur that the final term in the denominator of Eq. 4 results in a small error. Examples checked revealed less than I ft error, and corrective expressions for the four possibilities of displacement follow. The portion of the denominator within extra large brackets represents the original term W,, = weight of outside fluid displaced per unit length. The authors interpreted the expression "displaced" in general oilfield terminology as a fluid displacement, such as "mud displaced with water, etc." A review of the theory forming the basis for these helical buckling calculations discloses that this displacement is meant to be interpreted in the Archimedean sense, i.e., fluid displaced by the solid body. here the tubing and the seal nipple. Lubinski* illustrated the point by summing moments due to mechanical and hydraulic forces acting on a free body immersed in fluid. This moment summation, always in the Archi,medean sense, yields effects of the real forces, including W,, and the fictitious force on the bending mechanism. I would be interested to hear the authors' comments regarding this theoretical point, which nevertheless is not mute since its lack of recognition seems to result in erroneous calculations. We must not remain mute to Leutwyler's suggestion that these equations, although computer oriented, are confusing to the slide rule engineers. Such input information as density in pounds per gallon, pipe diameters in inches, pumping rate in barrels per minute and pipe length in feet is not confusing to most of us. Yet there may be some rugged individuals in field positions who carry tables of conversion constants and have committed to memory such items as coefficients of thermal expansion and Poisson's ratio; however, even this type of individual would welcome a simplified equation occasionally. M

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

By A. R. Ledoux

I WAS wondering whether we were going to adhere to our text. It seems to me that we are having a very remarkable meeting of mining engineers this year, because no matter what the texts may be that are assigned to us, we get back toward something higher; we turn to the consideration of questions of ethics, and of applied Christianity. Yesterday we listened to the most eloquent and remarkable address by Mr. Rickard in memory of Dr. Raymond, and it was told us that he was to speak about Raymond's achievements as an engineer. He did say considerable on that subject, but he was himself carried away with the spirit of the man and moved us all by his portrayal of Dr. Raymond's continued and fruitful labors for the betterment of mankind-that is to say his religion. Our President asked me if I would say something this afternoon and I find in the bulletin that the text of the discourses which we are to have here this afternoon is "International Cooperation in Mining in North America." But again I find that the eloquent speaker who has just preceded me has dwelt largely on ethical and spiritual cooperation rather than upon cooperation in mining. That is, cooperation as men, rather .than solely as engineers. The imaginary line dividing Canada from the United States, unmarked by fort or military post, was mentioned by a previous speaker. There are going to be in the future, I am sure, fewer entanglements of the barbed wire of tariff discrimination along our border-to that end let us cooperate. But there has always been a reciprocity in men. A Canadian conceived and created our great transcontinental line, the Great Northern Railway; an American made the Canadian Pacific what it is. In mining and metallurgy, American engineers, backed by American capital, have built up great Canadian industries while Canadian experts have developed some of the resources on this side of the line. They have done much more than develop our resources: some of them have been our leaders in sympathy for labor. It is therefore not a question of creating a spirit of cooperation, but of giving it freer scope and a fuller realization of fraternity-or, to use the .word now more common and of deeper significance-brotherhood.

Jan 4, 1919

The following have been compiled from information furnished through the courtesy of Dr. W. P. Haynes, of London, and Mr. T. V. Grigorescu of Ploesti, Rumania. Gura Ocnitzei was the most active field during the year, furnishing 40 per cent of the production and 50 per cent of the drilling activity. Extensions to the west in this field were made both by Concordia and Romana Americana. In these new extensions the bulk of the production comes from the Drader member of the Dacian, with an average depth of 1300 m.; the underlying third Meotic at 1700 m. has not been developed yet. In Gura Ocnitzei east no new drilling has been done in 1933, but here declining pressures have led to the extensive use of gas-lift and pumps. Ochiuri saw some small drilling activity, but production declined. Two good wells were brought in by Unirea and Astra at the close of the year. Boldesti continued to be developed on a general plan by the four major companies interested. Production was from the Meotic, which in this dome has been penetrated for 356 m. Reserves have been estimated at about 63,000,000 bbl. An important discovery in this area was the bringing in of Credit Minier No. 1 Harsa to the east of the main field and producing from the Meotic. This well came in during October, 1932, and is now making 1400 barrels. In the Moreni Piscuri field only routine operations have been carried on. The prolific sands are now declining rapidly. Ceptura also saw only routine operations. In the Arcesti field development of the Meotic continues. Seven new wells were brought in during the year and ten were drilling at the close of 1930. The field produced over a million barrels for the first time during 1933. In the other fields only routine operations were carried on. A considerable increase in efficiency of operations was noted during the year. The average drilling time has been reduced, coring programs have been amplified, and much care has been taken in straight hole drilling. The Schlumberger electrical coring apparatus is extensively used. Electric-driven rotaries have been introduced at Gura Ocnitzei. The Moniteur du Pétrole Rouman reports that the index cost of drilling one meter, taking 1929 as a base of 100, has been reduced to 32 in 1933.

Jan 1, 1934

By M. Albertson

At Cobalt, Ontario, Canada, a lake was drained to facilitate mining, by the Mining Corpn. of Canada, during the spring and early summer of 1915. Previous to pumping out the water, great quantities of sands and slimes from concentrating plants had been discharged into the lake and during and after the lake's drainage, its basin was a receptacle for tailing products. As the writer was at work along the shore line as the lake was being drained, he had a good opportunity to observe the changes that took place as the water was withdrawn. Some adjustments between the incoming sands and the mud in the lake had taken place before pumping was commenced. One of the most interesting results was the appearance of a small dome in a path the writer traversed twice a day for several months; he remembers distinctly the difficulty of crossing this. Cobalt Lake owed its existence to the gouging out of a rock basin by glaciation. The long axis of the basin closely follows the strike of a thrust fault of about 500 ft. (160 m.) vertical displacement. The lake was originally shaped somewhat as shown. The length was about 3000 ft. (914.4 m.), the width at the lower lobe was about 1000 ft., and the width at the narrows probably 400 to 500 ft. The original depth of water varied from 20 to 30 ft. (6.1 to 9.1 m.), near where the island later was formed, to 60 to 70 ft. (23.6 to 27.6 m.) in the widest part of the lower lobe. At the narrows, the depth was 30 to 40 ft. Above the bed rock was sand, with boulders near the bottom, and mud. During the building of the railroad in 1903, considerable filling was done along the right of way. With the commencement of mining operations, about 1905, waste rock and mill tailings were dumped into the lake. One of the mining companies operated a hydraulic giant to remove the glacial debris from several hundred acres of rock surface; much of the sand and clay from this operation was deposited in the lake. About 1,500,000 tons of mill tailings, composed of sands and slimes, were discharged into the lake's waters previous to 1915. Most of this material

Jan 1, 1921

By V. R. Garfias, A. C. Fernandez

Despite artificial curtailment in all the fields of Mexico during 1937, owing to strikes and other disturbances, the production of crude petroleum aggregated approximately 46,738,000 bbl., showing a substantial increase of about 5,571,000 bbl. over the preceding year. Most of this increase occurred in the Poza Rica area, where, although only two wells were completed during the year, production increased from 14,162,000 bbl. in 1936 to 18,634,000 in 1937. While production in the South fields (Golden Lane) remained practically stationary, the output in the heavy-oil district of the Northern fields showed an increase of 1,930,000 bbl., because production had been considerably curtailed during 1936. Production in the Isthmus of Tehuantepec decreased about 596,000 bbl., owing to labor disturbances. Crude run to stills in local refineries increased from 34,000,000 bbl. in 1936 to 36,650,000 in 1937. Exports of crude and refined products were approximately 22,700,000 bbl., or 500,000 bbl. less than in 1936. Domestic consumption, excluding ships bunkers, reached a total of 20,000,000 bbl., which shows a small increase of 200,000 bbl. over the. previous year. Domestic demand for gasoline is estimated at 3,400,000 bbl. for the year, which represents an increase of 500,000 bbl. over 1936. In all, 60 wells were completed in Mexico during 1937, as compared to 70 in 1936 and 74 in 1935. In proven areas 52 completions resulted in 25 producers and 27 failures. In the Northeastern area near the United States border, five gas wells were drilled, all of which were producers; one of them, in Camargo, came in with a daily production of 20,000,000 cu. ft. of gas. One well, resulting in a failure, was drilled in Las Uvas, Coahuila, and three wells were completed in Quebrache, to the southeast of the heavy-oil district, resulting in two small producers and one failure. TWO more wells drilled in San SebastiBn, east of the Golden Lane, were failures. Fields Northern Fields (Heavy-oil District).—A total of 11 producers and 22 failures was completed in the proven areas of the Northern fields, as compared to 16 producers and 25 failures in 1936. In the Altamira

Jan 1, 1938

By E. E. Barker

ALTHOUGH flotation was known to be a successful process prior to 1912, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on, a full flotation basis. EFFECT OF FLOTATION ON ORE RESERVES The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Sackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928