Search Documents

By E. S. Porter

The techniques of particle-size measurement are of particular importance in the manufacture of portland cement. A range of sizes, from a close approximation to Fred C. Bond's "theoretical infinite" (represented by raw material in the quarry) to particles smaller than one micron is represented in the process. Moreover, similar size-reduction operations are performed on both natural and synthetic materials, the former relatively inactive in water and the latter quite reactive. This means that aqueous sedimentation systems for particle-size analysis are applicable only to some of the materials involved in the process. A brief review of the process should be useful to place the measurement techniques described here in perspective. (Fig.l) Raw materials are quarried, crushed and transported to storage at a maximum size usually of a few inches. Typical materials are limestone and clay or shale, with small amounts of other materials used to adjust the plant mix to the concentration of lime, silica, alumina and iron oxide required.

Jan 6, 1962

T. M. Morris (Measurement and Evaluation of the Rate of Flotation as a Function of Particle Size, P. 794), was the commanding officer of a patrol craft charged with guarding Aleutian waters against infiltration by the Japanese during World War II. Before going into service, he was an assistant research engineer with Anaconda Copper at Anaconda, Mont., and later a metallurgist with Tennessee Copper Co. Presently he is a professor in the Department of Metallurgy, Missouri School of Mines, Rolla, Mo. A member of the AIME, he is a graduate of Columbia University and the University of Missouri, with a Bachelor of Science, Master of Science and a Ph.D. Professor Morris is the author of a previous paper for the AIME, Measurement of the Equilibrium Forces Between an Air Bubble and an Attached Solid in Water. An outdoor man by predilection, he enjoys bird watching and hiking in his free time.

Jan 1, 1952

By Joseph Cervik

INTRODUCTION Common methods of controlling gob gas in U.S. mines are by means of ventilation of gob areas and gas drainage through surface boreholes. Costs of drilling surface gob holes increase as deeper coal- beds are mined. Where gob holes cannot be drilled because of topography, ventilation is the only means of control. Even then, sufficient air may not be available to dilute methane in the bleeder entries to acceptable levels. Thus, new methods of gob gas control need to be developed that are independent of surface topography, and of the mine ventilation system, and less costly than present systems. Except for slight variations in procedures and equipment, Great Britain, West Germany, France, Belguim, Poland, and Czechoslovakia use a common methane control method that is different from the system generally used in the United States. This Bureau of Mines paper reviews European mining methods, mining conditions, and methane control technology and discusses their applicability to U.S. mines.

Jan 1, 1981

By George F. Kunz, Henry S. Washington

The recently discovered occurrence of diamonds near Mur-freesboro, Pike county, Ark., was brought to our attention by Mr. Samuel W. Reyburn (Trustee for Messrs. C. S. Stifft, A. D. Cohn, August Zinsser, Jr., and himself, owners of the property), through whose courtesy we investigated the locality of the deposit. Prospecting with the diamond-drill is now in active progress; but mining operations on a large scale have not yet been ordered. Geology.—The geology as well as the petrography of this interesting locality has been well described by Messrs. J. C. Branner and R. N. Brackett,' but they did not class it as dia-mondiferous, although Branner suggested that it might be. Briefly summarized, the igneous rock in which the diamonds are found is a vitreous peridotite, forming a stock or volcanic neck, which has broken up through the Carboniferous and Cretaceous quartzites and sandstones. After an extensive period of erosion, during which an unknown portion of the neck and pre-

Jan 1, 1909

By Bernard Rachlin

In the mineral industry measurement of density or specific gravity of slurries is often necessary or highly desirable. To date the most successful method of measuring the specific gravity of various media is to hand weigh a constant volume sample of the slurry. This method is time-consuming, however, and is intermittent rather than continuous. Most density measuring instruments in use today are variations of three basic systems: air bubble tube systems, radioactive methods, and displacer systems. The high cost of the radioactive cell, combined with the precision electronic measuring that is required, limits the practical utility of this procedure to a small percentage of critical processes. In the air bubble systems clogging of the bubble tubes with solids has rendered this type of measurement completely ineffectual for many applications. Continuous or intermittent purging of the bubble tubes with air or water to prevent tube clogging has been tried but has not been very successful, especially in the heavy media process.

Dec 1, 1956

By H. N. Mills

The glass industry is a major user of many industrial minerals in the manufacture of its product. It is the intent of this chapter to: (1) acquaint the reader with the glass industry by including a few production statistics, and then (2) cover the various aspects of the major raw materials used to make glass. Some of the items covered are: type of materials, their function in glass, their composition, cost, and the relative quantity used in glass vs. totals produced. In addition, a discussion of glass raw material specifications, some byproduct materials used in glassmaking, and comments on future prospects related to the environment, technology, and growth are included. The matter of glass compositions, properties, and batches is considered beyond the scope of this chapter which deals only with raw materials. For more details on the particular minerals and rocks, the reader is referred to the commodity chapters in this book.

Jan 1, 1975

B. S. Crocker (Screened Ore Used for Fine Grinding at Lake Shore Mines, P. 499) was born in Toronto, Ont. and attended Saint Andrews College and University of Toronto. He received a B.A. and M.A. degree. He was graduated with honors and received a fellowship in metallurgy. Mr. Crocker did post-graduate research at University of Toronto from 1933 to 1934. He was employed by Beattie Gold Mines in 1933. He did research in milling at Lake Shore Mines from 1934 to 1936 and from 1936 to 1940 was head of experiment laboratory. At the present time he is mill superintendent with Lake Shore Mines at Kirkland Lake, Ont., Canada. Grinding, cyanidation, flotation and roasting are of special interest to him. He is a member of AIME. Mr. Crocker has presented several papers before C.I.M.M. and also holds membership in this society as well as Professional Engineers of Ontario. Skiing, yacht racing and photography are his favorite hobbies.

Jan 1, 1952

In situ mining is no longer a "last ditch" approach for recovery of uranium, but a proven and competitive method of exploiting sedimentary deposits. Today, in any feasibility study of uranium properties, the project manager would be prudent to compare the economics of in situ methods with conventional surface and underground techniques. In this comparison of in situ and open-pit mining, John J. Borkert and Carl E. Gerity of Occidental Minerals Corp., evaluated a group of hypothetical uranium deposits using the three most sensitive depositional characteristics of depth, size, and grade. Their conclusion: in situ is generally the better method to maximize total net profits and return on investment. At uranium values of $40 per pound, their analysis found open-pit mining to he unprofitable, generally, when stripping ratios were greater than 30:1, the deposit grade-thickness (GT) was 0.5 or less, or the ratio of depth to GT was greater than 200.

Jan 10, 1978

By C. Richard Tinsley

Mineral economists debate whether to call the deep-ocean nodules "manganese nodules," "nickel nodules," "polymetallic nodules," or even "ferro-manganese nodules." It is nickel and copper that are generally regarded as the main targets in the nodules. Processing considerations are thought to virtually dictate that Deepsea Ventures will produce high-purity manganese metal (at least if it follows a hydrogen chloride leach), whereas other groups have been focusing on the selective extraction of copper, nickel, cobalt, zinc, and molybdenum, while rejecting manganese to tails. Solvent extraction appears to be the primary multimetal extraction technique (except for manganese). These processing considerations indicate that metal production f, or Deepsea Ventures is essentially a co- product system (manganese recovery is necessary to recycle chloride ions) while the other groups can more easily approach the metals as selective co-products (e.g. recovering nickel and copper, and rejecting cobalt). Some zinc may be produced as a co-product, as it may have to be removed in the solvent extraction process.

Jan 4, 1975

Discussion of the paper of Robert Franke, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1201 to 1205. ARTHUR 0. GATES, Lafayette, Ind. (communication to the Secretary*) :-In connection with the comparison of mechanical crushing efficiencies in Tables I and II of Mr. Franke's paper, I wish to suggest a somewhat simpler way of making this' comparison, based upon what the writer has called the "crushing-surface diagram," as published by him in the Engineering and Mining Journal for May 24, 1913. Such a diagram, based on the data given in Table II, is submitted herewith, Fig. 1, cumulative percentages being plotted as abscissas and reciprocals of diameters (theoretical mesh per inch). plotted as ordinates.. Such a diagram averages the diameters without calculation, and areas upon it are proportional to surface produced, and, in accordance with Rittinger's law, to energy spent on crushing alone.

Jan 11, 1913

By H. M. Merry

THE graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts, the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution; percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required.

Jan 9, 1919

By Guang Ping Cui

In this paper the imminent relationship between rock burst and its phenomenon with normal rock pressure and its appearance, as well as the factors of one changing into another have been analyzed. Based on this, the necessary and sufficient appearing factors of rock bursts have been put forward, and the term ''burst pressure" has been defined. According to the statistics data of tremendous rock bursts which appear in collieries in Hunan Province, the features of high frequency, great strength and shallow depth of the beginning burst have been found. There are some special structures in the coal seams, which are closely related with the burst phenomenon. A hypothesis of "star structure" has been suggested for the appearing mechanism of bursts. Inside and around this star structure the distribution rule of burst pressure and rock strength has been researched depending upon the theory of the limited stress field. A new description of the appearing causes of bursts has been raised.

Jan 1, 1984

By W. M. Tuddenham, R. J. P. Lyon

In many areas surrounding the orebodies in mining districts rocks have been bleached and altered by the ore-forming solutions and have been oxidized during later weathering processes. A number of the rock-forming silicates have been broken down to clay, sericitic micas and chlorites have been developed, and pyrite may be found hundreds of feet outside the economic limits of the orebody. These halos of altered ground are prime targets used by geologists in many districts to delineate promising sites for drilling. Both in the field and in the laboratory it is often difficult to map these mineralogical changes in the halos in detail without numerous petrologic examinations. The secondary minerals are generally fine-grained, and since conversion of one mineral to another is often progressive, many alteration processes have not proceeded to completion (feldspars to clay to sericite mica). Qualitative detection of these minerals is difficult; quantitative determination is frequently impossible.

Jan 12, 1959

By Raphael D. Schilz, Michael F. Dunn, Edward D. Thimons, Francis S. Kendorski

During a mine fire or other emergency, it may be desirable to reverse the air flow in order to provide an escapeway or to control a fire. Also, in colder areas, the air flow may be reversed to prevent ice build-ups. When reversing main mine fans, the operator usually does not know what operating characteristics of flow and pressure to expect. Laboratory testing of vane axial main mine fans has been completed in order to establish forward and reverse performance characteristics under controlled conditions, with the results presented here. Preliminary tests under field conditions have also been conducted. The data obtained suggest that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. There is also evidence that reverse performance can he predicted for a family of blade angles in a given hub to tip ratio. In general, the air quantity delivered by the fan is 30% to 60% less in reverse than when operating in the normal forward mode.

Jan 1, 1982

By R. J. Lutton

Basic features occurring on tensile fracture surfaces in rock are hackle marks, steps, and rib marks. Rib marks define the leading edge of the fracture and indicate that it was free of irregularities. In turn, fractures characterized by these features are believed to have propagated elastically and to be truly brittle. On the other hand, most fractures in rock exhibit hackle marks and steps in a plumose arrangement, indicating a ductile fracture process. Accordingly, the edge of the fracture apparently advances by extending en echelon fingers, each of which is in turn a small plumose fracture. Plastic-like deformation takes place in this zone prior to complete rupture. Some of the propagation is directed sideways and some shearing also occurs in this direction. Such lateral movement contributes little to forward propagation and may make this process particularly sensitive to load rate and duration and help account for greater fracture strengths of materials under dynamic loads.

Jan 1, 1971

By C. W. Kempton

If New England were located in some distant and almost inaccessible region, there is no doubt that its mineral resources would have been ere this well developed and generally acknowledged, but laboring under the disadvantage of nearness, it has been neglected. Its surface, moreover, is not cut up by mountains and canons, and the remnants of many of the old ridges are extensively covered by glacial drift. Having for the past ten months been engaged in the development of a mineral district in Southeastern Maine, 1 would take this opportunity to lay before the Institute sketches of results, and try to give some idea of the formations as found. The Sullivan Mining District extends from the town of Franklin, through Hancock, Sullivan, and Gouldsborough, from northwest to southeast, about sixteen miles. A general idea of this locality may be gathered from the map accompanying. (Fig. 1). Sullivan is situated at the head of Frenchman's Bay, ten miles north from Bar Harbor, Mount Desert, twelve miles from Ellsworth,

Jan 1, 1879

By Joseph P. Hodgson

JOSEPH P. HODGSON.-As to ".Safety First," I did not deal with that, but I will say that in 1913, the number of .men killed was nine, and that year the "safety first" program was commenced; the next year, 1914, the number was reduced to five. In 1915, I am pleased to say that the number was reduced to two in the Copper Queen's entire property, and we have none so far this year. THE CHAIRMAN (G. F. G. HERMAN, Bisbee, Ariz.).-I can say, further, that we have from eight to nineteen men per month incapacitated for more than 14 days. Those are classified in this State as serious accidents. The number of men injured has apparently increased, -but that is clue to our improved method of recording and classifying accidents, no matter how slight. C. W. GOODALE, Butte, Mont.-The importance of cooperation among the members of the staff of an industrial organization is well brought out by Mr..Hodgson's paper.

Jan 12, 1916

By W. D. Lacabanne

DRILLING fluids as an aid in drilling holes into the earth have been in use successfully for more than a half a century. Originally used in a primitive fashion in water well drilling before the turn of the century, drilling fluids came into their own in 1901 when they were incorporated as an indispensable part of the newly invented rotary oil drilling method. Since drilling fluids have been the basic factor in successful modern oil well drilling, at- tested by the dramatic growth of the U. S. petroleum industry, their study and development have naturally taken place in the oil industry. An abundance of engineering and scientific literature has appeared on the subject of drilling fluids. Application to Exploration Drilling The drilling fluid system is understandably called the heart of the rotary oil drilling rig. Any other type of rotary rig, such as the diamond drill, should benefit by the incorporation of mud fluids in the drilling scheme.

Jan 12, 1954

By Ramachandra Rao

THE occurrence of copper ores at Garimenapenta, 14 59 min 30 sec N Lat., 79 33 min 10 sec E Long., in Nellore district, Madras State, India, has been examined and investigated on numerous occasions during the past two centuries.' No tangible orebody was ever located as a result of all the ex- tensive trenching and shafting done in the area by various agencies. However, during 1933 Messrs. Piepmeyer & Co., a German firm engaged by one of the leaseholders of the area, carried out an electrical survey using inductive methods.' On the basis of certain strong indications found in their survey, they recommended that the prospect be proved by drilling or shafting. But for want of financial backing no further work was carried out. When the Madras government more recently proposed investigation, Dr. Krishnan, then Supt. Geologist of the Madras Circle, urged that before further costly ventures were carried out a test geo-

Jan 1, 1954

By W. J. Travers

SEVERAL new procedures for completing oil wells have been developed in recent years. Each method when used where properly applicable promises to be a definite aid to operators in lowering development or operating costs, or in developing the full potentialities of the oil well. Multiple-zone completions are now frequently used, in contrast to the older practice of setting a solid water string over each zone to be produced. Gravel packing in unconsolidated formations often prevents sand troubles formerly experienced where a conventional perforated liner was used. Light-weight bentonitic clay muds and oil-base drilling fluids are definite steps toward eliminating mudding damage, which occurs when heavy rotary mud is used. Since in each case the new procedure developed is an alternate of older conventional methods, a problem of selection is presented. The purpose of this paper is to suggest methods of arriving at these choices and to present practical observations that may be of aid in their application.

Jan 1, 1942