Search Documents

By John Gross

THE deductions drawn in crushing and grinding operations have heretofore been based on a separation of the products into various sizes. A crushed product may be sized by sieving, by elutriation, and by aid of the microscope. To estimate the surface of each size the relation of the surface to the estimated average diameter must be assumed. Such a relation, owing to the irregularity of the particles, may involve two assumptions: First, a factor to convert average diameter to surface for one particular size; and second, a variation in the factor as the diameter of the particle changes. Obviously a surface measurement in which such assumptions and estimates are involved is questionable. In the first paper of this series1 a method has been given by which an accurate measure of surface of quartz can be obtained from its dissolution rate. By the use of this method, surface measurements have been made on a series of sieve sizes of crushed quartz, the results of which are given and discussed in this paper.

Jan 1, 1928

By W. G. Moffatt, J. Wulff

BRAZED joints and their strength have for some time been of great practical as well as theoretical interest. A good summary of the previous work in this field may be found in the reports of the Armour Research Foundation. In spite of excessive scatter in test data, the fact that the strength of a brazed joint may exceed the ultimate strength of the brazing material itself by many times continues to be of interest and of value in engineering. That this is qualitatively due to plastic constraint of the brazing material by the faying surfaces of the base metal is not in dispute, yet no complete interpretation of the data exists. The purpose of the present work is not to provide such a new interpretation, but to report new experimental data which we hope may lead to a better understanding of the important variables concerned. The work of Bredz' definitely shows that the thinner a brazed joint is, the greater is its strength. Dianeter of a joint has seldom been taken into

Jan 1, 1958

By Carlos D. da Gama, Charles R. Nelson

Griffith’s theory of brittle fracture, as modified by McClintock and Walsh to fit rock behavior in cases of failure by compression, has been successfully applied in various fields of rock mechanics. Extension of the Griffith's criterion to rock blasting problems may also be more representative of rock behavior than the simple consideration of a criterion of failure based on the dynamic tensile strength of the material. If consideration is given to pre-existing cracks within rock structure, occurring not only because of the discontinuous properties of rocks, but also as a result of drilling operations that normally precede blasting, those cracks can be propagated under the action of the dynamic stresses (radial and tangential) induced by the passage of the wave emitted by the explosion. Conditions for initiation and propagation of pre-existing cracks are deduced in terms of rock properties and explosives performance. Influence of the different variables governing the phenomenon is discussed after considering an actual example. Results seem to be well correlated with experimental evidence of radial cracking observed in blasting with high explosives acting within hard rock.

Jan 1, 1971

By W. E. Anderson, T. M. Brady

As part of a larger study to identify factors influencing the practical operating life of wire rope used on large draglines in surface coal mining, field trips to operating surface coal mines were made during late 1975. Wire rope performance information was obtained from personnel at 13 mine sites west of the Appalachians. Seventeen pieces of equipment, utilizing bucket sizes ranging from 30 to 220 cu yd (23 to 168 m), were documented. Draglines at large US surface coal mines can be represented as 120 machines having 60-cu yd (46-m3) buckets, moving 1.8 x 10[9] cu yd (1.4 X 10[9] m3) of overburden during 6650 hours of productive availability per year. Based on the limited field study, the calculated downtime resulting from rope-related causes averages 105.6 hours per year for each typical 60-cu yd (43-m3) dragline. The total loss in production from this source alone is thereby estimated at about 25 X 10[6] cu yd (19 X 10[6] m3) annually.

Jan 11, 1979

By G. H. Walrod, J. M. Mutmansky, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to 1000 ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1979

By John L. Watson

A conceptual model (MAGSEP) is described to simulate the beneficiation characteristics of a drum magnetic separator in terms of the probability of an individual grain being recovered in the magnetic concentrate. This probability is determined as a function of particle magnetic composition and magnetic field strength and is modified by particle size and the separator operating conditions. The model predicts the size, magnetic grade and distributions of magnetic and gangue minerals in the concentrate and tailings produced by the drum separator. The configuration of the magnetic concentration circuit may be altered to permit single or double drum units in parallel or series operation. The characteristics of the feed material, in terms of a magnetic parameter, are essential in permitting the determination of individual grain recovery probabilities upon which the model is based. Thus the model requires input data relating to the distribution of composite grains in terms of magnetic grade and particle size. To illustrate the use of the conceptual model an example is given for the beneficiation of New Zealand iron sands.

Jan 1, 1984

By H. I. Smith

WHEN Spain established colonies on the North American continent, some of her land grants, in what is now the United States, reserved to the Crown deposits of gold, silver, and mercury. Later mineral rights were reserved under some of the English Crown charters involving land in the eastern part of North America, with provisions for the payment of royalties thereon to the Crown. Reservation of mineral deposits to the United States Government was instituted by an ordinance of Congress on May 20, 1785, which applied to such deposits in the Northwest Territory, then north of the Ohio River and east of the Mississippi River, and provided that there should be reserved "one third of all gold, silver, lead, and copper mines, to be sold or otherwise disposed of as Congress shall hereafter direct." Little was known then of the mineral resources of the country; the Great Lakes copper region had just come into the possession of the United States by treaty and much of the western mineral land still belonged to France and Spain.

Jan 4, 1954

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor-including metal, mineral, and fuel technicians-to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support.

Jan 11, 1958

By G. Kinder, R. Gilges, W. Stoker, R. Davey

The Bingham Canyon Mine, located 48 km (30 mi) southwest of Salt Lake City, Utah, is operated by Kennecott Copper Corporation's Utah Copper Division. This operation is the world's largest open-pit copper mine and produces 96 000 tons (106,000 st) ore and 327 000 tons (360,000 st) waste each day. This material is loaded by large electric shovels and transported by both truck and rail haulage. To meet the requirements of the Clean Air Act of 1970 (as amended), new facilities for the control of smelter emissions were required and are now nearing the final stages of construction. The facility will be capable of treating all the output from the mine, some 2,530 tons (2,789 st) per day of combined concentrate and precipitate. Costing $280 million and necessitating the replacement of reverberatory furnaces with continuous smelting vessels, the plant, with its massive and complex gas handling and acid-making facility, is required to remain on-stream with the minimum of pollution control equipment outages to conform with Federal Regulation 52.2325.

Jan 8, 1978

U.S. Steel Uncovers Massive Iron Ore Deposits in Nevada United States Steel Corporation has confirmed that mineral investigation in Lyon County, Nevada. has been under way since 1960. Confirmation followed press reports of a statement attributed to a Nevada State inspector of mines to the effect that the Corporation has found a major iron ore deposit that may also contain copper ill West Central Nevada. Drillings over the years in a number of locations have indicated extensive iron ore bodie containing a possible quarter of a billion tons of ore of a basically magnetite composition. analyzing less than 40% iron, which would require beneficiation for commercial use. Some of these deposits are deep- lying while others would permit open pit mining. These bodies contain copper in quantities of approxiimately 0.3%. More recent drilling in another area has disclosed evidence of additional deeply-lying deposits of a lower fe content but with more promising indications of copper. A realistic estimate of fe and cu ore reserves cannot be made until more drilling is completed.

Jan 1, 1970

By David B. Campbell

Production of both metallurgical and thermal coal represents a significant sector of the mining economy of British Columbia. The coal measures are located in the Rocky Mountains, and the majority of the coal is produced by open pit mining. The coal seams occur interbedded with siltstones, sandstones, mudstones, and shales. Consequently, large volumes of waste rock are generated in the course of open pit mining. The waste rock is consigned to waste rock piles that of necessity must be developed on moderate to steeply sloping terrain. Some of the waste dumps currently under development will ultimately contain in excess of 500 million cubic meters of material, and some of the proposed waste piles will attain heights in excess of 300 m. These waste piles must be developed in a manner that will assure their stability through all stages of development, as well as over the long term after mining operations have been completed. This paper describes methods of waste dump development, factors affecting stability, modes of potential failure, and a simple method for monitoring movements to provide a warning of pending unstable conditions.

Jan 1, 1985

By F. B. Richards

For the last five years the furnace-men drawing their oresupply from the Lake Superior districts have had to solve the problem of using the very fine Mesabi ores as part of their oremixture. It is not my purpope to dwell on the early experiences and the progressive development in the use of these ores up to this time, but to lay before the members of the Institute one prominent feature concerning them, namely, the frequent and sometimes very disastrous slips (?) or explosions (?) occurring at furnaces where these ores are used. The Transactions of the Institute contain very little on this subject. Mr. F. E. Bachman, in his discussion of Mr. 0. 0. Laudig's paper (Trans., xxvi., 1061), advances a theory as to the cause of these occurrences; but this is the only reference to the subject in the Transactions up to this time, so far as I can recall. Probably all the furnace-men running the harddriven coke-furnaces in the central West have had more or less experience with this trouble; and I believe the majority of

Jan 1, 1899

By David J. Mack, Chin Bea Kim

The decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was studied by isothermal transformation. Its progress was followed by metallographic, hardness, and X-ray diffraction methods. Three transformation products were found: lamellar pearlite at high temperatures; an intermediate temperature structure; and martensite at the lower temperaCures. No transition structu,ves were found. THE decomposition of the Ni-Zn eutectoid at 56 wt pct Zn was stuadied as part of a long-range program of study on the eutectoid transformation in alloy systems which do not have one or more components which exhibit allotropy. Available information on the Ni-Zn eutectoid transformation is limited to that presented in connection with the determination of the phase dilagram. No systematic studies of the eutectoid were found in the literature, alkhough the microstructures of the Ni-Zn eutectoid were reported by Tamuru.3 X-ray diffraction data exist for the ß, ß1, y , and y1 phases.' EXPERIMENTAL PROCEDURE The eutectoid alloy was prepared from "A" nickel shot and Bunker Hill super-purity zinc (99.998 pct).

Jan 1, 1962

By D. D. Porter, C. Fairhurst

Crack propagation in the region of a statically pressurized borehole is investigated to determine a role of the sustained borehole pressure following detonation in a blast. The case of a single-hole bench blast is reduced to a plate model, which is considered both theoretically and experimentally. Based on the principle of least work, it is hypothesized that the path of any crack in the plate will coincide with one of a family of maximum principal stress trajectories. These trajectories were computed, and critical experiments in glass, designed to test the effects of controlled crack origin and of changed trajectories from different loading configurations, confirm this hypothesis. It is concluded that under ideal conditions the crack path can be predicted and that cracks can be produced in the absence of either high-amplitude stresses or stress waves. Energy considerations for crack extension are discussed, and, based on the strain energy distribution, a relationship between hole burdens and spacings is revealed, a critical burden is demonstrated, and a maximum crater width is shown to exist.

Jan 1, 1971

By H. L. Riley, B. W. Gandrud

As far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales. The system has been described and discussed in a number of publications. The following is quoted from an abstract of the latest of these," a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption.

Nov 1, 1955

By G. A. Koenig, Moritz Stockder

Locality and Geological Occurrence. The Alpine region of Southwest Colorado, comprising the San Juan and Uncompaghre Mountains, is composed of a deeply eroded sheet of acid eruptive rocks, overlying in part gneissic sehists, and in part limestones and sandstones, including portions of the Silurian, Devonian, and Carboniferous systems. The section is clearly and beautifully exposed along the Uncompaghre River from its headwaters to its exit from the mountains. The river's course from the town of Ouray towards the Los Pinos agency is due north, and four miles from Ouray, in this direction, the Uncompaghre receives from the east the Red Cafion Creek. Following up the narrow caftan we find the section through white.. sandstone in strata dipping to the north and west, and belonging either to the lower or middle Devonian system. Presently the steep cafion-liko character of the ravine gives place to more gentle slopes, and we have entered crystalline rock-porphyry. The contact is well marked, for the sandstone, to a depth of from six to ten feet, resembles quartzite, i. e., is semifused. Ascending still higher, a small

Jan 1, 1881

By T. L. Kesler

With only six small spodumene prospect pits, no detailed mapping, and no subsurface information in 1938, the Carolina lithium-pegmatite area now contains four mines among more than 25 properties on which exploratory work has been done. Even the open pit mine of Foote Mineral Co. described herein, from which ten million tons of ore and waste have been removed since 1952, was virgin ground when mapped in 1938-40 1. It has been a privilege to participate in the transition. In 1940, the spodumene pegmatites were known in a 25-mile belt (originally noted for tin prospecting) between Lincolnton, N. C. and Grover at the South Carolina line. Subsequently, Broadhurst 2 reported relatively small bodies northeast of Lincolnton near the Catawba County line. To the south, diamond drilling done in 1953 on the old Ross tin-mine property near Gaffney yielded pegmatite cores containing a few crystals of spodumene. This fact, not previously reported, suggests that some of the pyroxene in the Ross shaft as described by Sloan 3 may be spodumene.

Jan 9, 1961

By T. Katayanagi, J. Shimoiizaka, K. Nakatsuka

Feldspar has been separated from silica by cationic collector using hydrofluoric acid as an activator of feldspar (1,2). Recently, one of the authors developed a new flotation process separating feldspar from quartz without using hydrofluoric acid. Presently, some silica sand mills are operating to introduce this process in Japan (3). In this flotation, feldspar is floated from silica using normal alkyltri-methylene diamine acetate together with sodium petroleum sulfonate as collectors in a hydrochloric or sulfuric acid circuit of about pH 2. From fundamental studies, it was found that, though the aliphatic diamine by itself did not adsorb on feldspar sufficiently to give a satisfying flotation in acidic circuit., the adsorption of collector was promoted by the simultaneous use of petroleum sulfonate and resulted in sufficient flotation of feldspar. On the other hand, quartz did not float in this flotation process. The application of this flotation was attempted for some types of natural samples and satisfying results were obtained. Further, an example of practical plant was introduced and the advantages in the process are emphasized.

Jan 1, 1976

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to l000ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1980