Search Documents

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function' used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail' and the results are simple and generally applicable. 'The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy's law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

By George A. Packard

The shaft of the Raven mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70" from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47. This angle continues to the 1,100-ft. level, below which it curves with a 125-ft. radius to 78". In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging and foot walls, but presses strongly against the west dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, aid wall plates cut 6 in. deep by the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging wall of the shaft the original bearing was simply a piece of + by 1 3/2 in. strap iron, 10 in. long, turned up at the end in a circle 11/8 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 1, 1915

By H. B. Aaron

DIFFRACTION micrography provides a useful tool for studying complex strain fields. Newkirk1 observed an X-ray diffraction effect due to strain interactions at the intersection of slip lines in LiF and attributed this effect to a reduction of primary extinction due to strain-gradients. It is the object of the current study to correlate the observations and rationalize the appearance of the strain fields around intersecting slip planes in x-ray extinction contrast studies by a semiempirical method. Fig. 1 shows typical strain patterns observed by Newkirk on (200) reflections in LiF using chromium radiation and a variation of the Berg-Barrett (B-B) technique. In other reflections (e.g., {220}) the strain patterns are absent. If one defines a vector 3 along the striations from the more to the less dense portion, and a vector v in the direction of the X-ray beam parallel to the reflecting plane, such that both 3 and v lie in the reflecting plane of the crystal, Fig. 1, then the positions of the striations on (200) reflections appear to be confined such that where is the angle between v and 3, Fig. 1. It will be seen later that 3 is the projection of Sb on the reflecting planes. In some instances the strain effects are observed only above the slip plane, Fig. l(C), in others only below, Fig. l(D). Where the strains appear to be both above and below the slip line, Fig. l(E), one sees that there are actually two slip lines present, Fig. 1(F) and (G). Furthermore, the strain patterns are observed in the vicinity of the intersection of emergent edge dislocations (diagonal lines on the micrograph) with emergent screw dislocations (horizontal lines on the micrograph), e.g., Fig. l(HJ) and (MN), but not in the vicinity of the intersection of two emergent edge dislocation arrays, Fig. l(HJ) and (KL). However, in the latter case the contrast of the dislocation array itself is reduced along (KL) and increased along (HJ). Line (AB) in Fig. 1 is the edge of the crystal, and the material to the left of (AB) is the side of the sample. Any empirical correlation will have to include most, if not all of the aforementioned observations. Lang2 and Newkirk1 determined that the condition for contrast is given by g-b#0 [2] where b is the Burgers' vector and g the diffraction vector (normal to the reflecting planes). If one assumes that the direction of the observed strain fields is given by the vector sum of the slip vectors (Sb1) of the intersecting slip planes, then Eq. [2] may be generalized to g-S#0 [3]

Jan 1, 1963

By W. A. Koehler, M. E. Hinkle

INTRODUCTION THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: I. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of fer¬rous (iron) sulphate and some sulphuric acid. 2. The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages nor¬mally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio¬bacillus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not yet been established. Apparently it does not promote the oxida¬tion of ferrous iron compounds in mine, drainage to the ferric state. The second organism has not been identi¬fied by name but is described as "Gram negative, non-spore-forming rods approxi¬mately 0.4 micron wide by o.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur com¬pounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced percentage of oxygen and increased percentage of carbon dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. ACID COAL MINE DRAINAGE Acid coal mine drainage has been the concern of coal mine operators, industrial¬ists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1948

By George Packard

THE shaft of the Raven. mine, at Butte, Mont., is an incline 1,700 ft. in length and dipping at various angles. At the top the dip is 70° from the horizontal, but this is gradually flattened until at the 300-ft. level the inclination is only 47°. This angle continues to the 1,100-ft. level, below which it, curves with a 125-ft. radius to 78°. In addition to these variations in dip, the shaft does not lie in the same vertical plane, with the result that the hoisting rope not only rubs at intervals on both the hanging- and foot-walls, but presses strongly against the west, dividers near the collar, while 300 ft. below it runs close to the east end plates. The early operators used no idlers, and wall plates cut 6 in. deep y the rope resulted. Later operators first attempted to overcome the excessive friction, and the wear of rope and wall plates, by introducing solid cast-iron idlers, 3 in. in diameter. To allow for the travel of the rope from side to side some of these had to be 3 ft. long and were very heavy. Judging from the appearance of the old idlers of this type found at the mine, they often failed to turn in the bearings, which is not surprising when it is considered that they would have to make 1,000 rev.. a minute under ordinary hoisting conditions. The next rolls were made of wood, 6 in. in diameter, with an iron band about each end, and a pintle of 1-in. round steel driven in at the ends to serve as a shaft. These wore rapidly, and were soon replaced by rolls made from water pipe, 5 or 6 in. in diameter, cut to the desired length and fitted with a wooden cylinder into which the pintle was driven. Where the idlers were used on the hanging-wall of the shaft the original bearing was simply a piece of 2 by 1-1 in. strap iron, 10 in. long, turned up at the end in a circle of 18 in. in diameter to receive the shaft. A small hole served for oiling, and common black oil was generally used, although filtered oil from engine bearings and compressor bearings was also used. When the rolls were to be placed on the foot-wall the bearings were made from two pieces of 1 by 3 in. steel, 6 in. long. A half circle was cut on the flat side of each piece and the two half circles together formed a bearing. Oil holes were provided, and in some cases holes were bored through the two pieces so that they could be screwed or spiked to the wall plates.

Jan 8, 1914

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

By Charles H. Morgan

THE process of wire drawing depends upon the property which certain metals possess, termed ductility, 'which is defined in Brande's Dictionary of Science as a property in consequence of which metals may be drawn out at length without interrupting the continuity of their constituent parts. As defined by M. Tresca, it is the property of flowing when subjected to pressure, and is termed by him the "flow of solids," in his paper, read before the Academy of Sciences in Paris, November, 1865 * In the simple language of the wire shop, it is that quality in certain metals that permit, them to be drawn (or stretched) out through a tapering, hole in a metal block or die, the die being more dense and harder than the metal to be reduced. It is a fact well known to those skilled in the art, that to succeed in drawing iron or steel wire, it is of the utmost importance to have thorough lubrication, as a lack of it would caws abrasion of the wire, or of the walls of the tapering hole in the die or plate, and quickly put an end to the operation. In drawing coarse or large sizes of wire, say 2/10 inch diameter, the pressure upon the sides of the tapering hole, where the wire comes in contact with the die, is so great that an ordinary lubricant is squeezed out when the usual reductions in size are made, and abrasion takes place. In order to meet this difficulty, and secure proper lubrication, it has been' a common practice for years to apply a paste made of rye or wheaten flour, or lime, to the surface of the wire to be drawn, and when the paste is dry, to smear the wire with tallow or grease; the wire is then ready to be drawn, the dried paste serving to prevent the lubricant from being pressed out in the. process. Some years since, when Bessemer metal came largely into use as material for wire, "the writer found that its drawing required so much more power than iron wire, that he was led to institute a series of trials to ascertain the difference in power required. It was found that Bessemer wire required from 100 to 200 per cent. more power to make the same reduction in sizes than soft iron wire, the difference depending upon the amount of carbon and other chemical constitu- * Interesting experiments in the flow of metals have been made, by Messrs. Hoopes Townsend, of Philadelphia, in cold-punching iron, published and illustrated in the Journal of the Franklin Institute, of March, 1878, by Mr. David Townsend.

Jan 1, 1881

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

E. P. Pfleider, University of Minnesota I would like to ask Bob Merrill whether he considers that horizontal concave curvature of a slope has any stabilizing effect, such as Jenike 1 suggested several years ago. R. H. Merrill, U. S. Bureau of Mines, Denver Federal Center The stabilizing effect is due to the restraint offered to radial movement by the curvature. We found in laboratory tests that if we constrained the rock with the same stresses as those measured in the pit then it would sustain a maximum stress about two or four times greater than when the same rock type was unconstrained. We are therefore definitely of the opinion that a constrained situation in a slope is favorable towards stability. G. A. Leonards, Purdue University I was interested in Mr. Lane's observations concerning the correspondence between rate of slide movement with rise of reservoir. Perhaps the most interesting feature is that the rate of movement at the time the rock slope failed was less than the rate at an earlier time when it did not fail. This is difficult to explain from current slope stability theory. K. S. Lane, U. S. Army Corps of Engineers I believe that reduced rate of movement is the result of the progressive type of failure, such as described by Patton and Deere. which occurs along the sliding surfaces. It is difficult to analytically define the progressive failure condition for inclusion in slope stability conditions, but its existence should be recognized in design. We should also realize that many apparently stable slopes undoubtedly contain overstressed regions. To design a slope with no overstressed region would be uneconomical and conservative. D. H. Deere I would pose the question-"What is the meaning of a factor of safety of one?" We were involved in the design of a large, irregularly shaped, underground cavity with an unsupported span of several hundreds of feet. Tests on rock specimens indicated a strength of 1300 lb per sq in. The RQD would have been between 90 to 100 percent indicating excellent structural continuity. In-situ stress determinations indicated an approximately hydrostatic state of stress at a level of 1400 lb per sq in. Calculation of stress concentrations at the walls indicated that the stresses there would be about 3000 to 4000 lb per sq in. Admittedly the rock is in a confined condition everywhere except at the very skin of the wall and the rock walls would thus on the average be somewhat stronger. Allowing for the effect of restraint the factor of safety was found to be less than 0.5 over a region several feet into the wall. Construction was started, using rockbolts only to support the walls. Failure around the immediate skin occurred after each

Jan 1, 1967

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By H. H

This paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. Characteristics of the Ore The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾, mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3Al2 (SiO4)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to I2 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crys- tals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3-07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive- Former Operations Mining operations have been carried on for 60 years. Until 1923, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By Norman Ketzlach

ANGANESE today overshadows all strategic materials in our planning for national se-curity," according to a report issued recently by the American Manganese Producers Association. By far the greater part of the manganese ore used in the United States is imported. "We have enough manganese ore in the United States to last from one hundred to three hundred years and longer, but most of the deposits are undeveloped. As in the case of copper, lead, and zinc, manganese ore, both foreign and domestic are low grade. Manganese ores have to be concentrated and processed. After being processed, domestic ores are higher grade than foreign." Most of the manganese ore found in this country, however, is not amenable to concentration by ore-dressing methods. Manganese Products, Inc. has developed a sulphurous-sulphuric acid leaching process for the recovery of manganese from low-grade, intermediate manganese ores. By the term "intermediate manganese ores" is meant those ores in which the manganese in the form of manganese oxides is found to have two different valences, usually two and four, as is probable in Mn,O, or the ore may be a mixture of manganous and manganic oxides. "Intermediate" manganese siliceous ores are ores in which the silica is a constituent of the ore and is loosely linked to the manganese by water of crystallization. This process has been carried out with the type of manganese ore found in the Olympic Peninsula of western Washington; Clough, N. C.; and Lava Hot Springs, Idaho, as well as just recently with manganese ore from Las Vegas, Nev. As far as the manganese leaching process is concerned, these ores differ primarily in the form in which the manganese oxides occur. The tetravalent manganese, the manganese existing in the dioxide form, is soluble in a sulphurous acid solution. To dissolve the divalent manganese, sulphuric acid is required. To dissolve the type of ore found in Washington and North Carolina, a mixture of both sulphurous and sulphuric acid is used. Whereas to dissolve the type of manganese ore found in Idaho and also in Montana, sulphurous acid alone is sufficient. The Nevada manganese ore is of the same type as that found in Idaho as far as the leaching process is concerned. It has long been known that manganese ores, with the exception of rhodonite, which is a true manganese silicate ore, can be dissolved readily in sulphurous and sulphuric acids.' The removal of the impurities such as silica, iron, and alumina from the resulting solution is the step that has been difficult. The process worked out by Manganese Products has been carried through pilot-plant equipment. This process has also been extended to the production of ammonium sulphate. Leaching of Ore: The manganese ore, ground to —-65 mesh is leached with sulphurous acid and sul-

Jan 1, 1951

By E. C. Houston, H. S. Rankin

Olivine is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be i purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 Per cent; Mn, 0.012 ; per cent; Ni, none. Chlorination† of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SupplY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.' The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940 It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. Previous Technical Work In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment6 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By L. G. Graper, E. L. Ramsey

The present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. Adding Sulphur as a Sulphite These difficulties can be avoided if sulphur is introduced into the stecl by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which—upon decomposition—forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium bisulphite. These samples were cut from the steels as cast—that is, before rolling— and were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. 2 shows that the sulphide inclusions arc more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. Results As stated before, the sulphur dioxide is added to steel by means of the decomposi- 27

Jan 1, 1942

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorinationt of olivine has two major defects: (I) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatments and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942

By A. G. H. Andersen, A. W. Kingsbury

SILICON bronzes containing iron are used to a considerable extent in industry, under the trade name of P.M.G. alloys. Various classes of wrought alloys fall in the composition range 1.5 to 3.5 per cent silicon, and 0.5 to 2.5 per cent iron. Castings may contain as much as 6 per cent silicon and 3 per cent iron at present. The constitutional diagrams of these alloys are thus of considerable practical importance. Copper-silicon-binary alloys have been thoroughly investigated by a number of workers, the latest reports being those of C. S. Smith' and of A. G. H. Andersen .2 Although much work has been done on iron-copper alloys,3 recorded investigations on the copper-rich copper-iron binary constitutional diagram are not numerous. Tammann and Oelsen4 determined the solubility limits of iron in copper by means of magnetic measurements, and found that the solubility of iron in copper amounts to a fraction of one per cent at 400°C., increasing slowly to one per cent at 800°C. From 800°C., the solubility increases rapidly and attains 4 per cent at 1100°C. Hanson and Ford," using electrical resistivity measurements and the microscope, determined a somewhat different solubility limit. Of earlier X-ray works on the copper-iron system, very little has been published. The work by Bradley and Goldschmidt6 on copper-iron-aluminum alloys includes some information on the copper-iron binary. These investigators conclude that substitution of iron in the copper lattice decreases the spacings, which is contrary to the evidence of the present work. Hanson and West7 have investigated the ternary alloys of copper with iron and silicon. Although their diagrams are valuable contributions to the understanding of these alloys, they did not recognize the kappa phase,1,2,7,8 and their diagrams do not everywhere conform to the phase rule. The present work contains a check by means of X-rays of the solid solubility limit of iron in copper, and an X-ray investigation of the ternary-phase diagram, which, owing to present conditions, it became necessary to curtail considerably. PREPARATION OF SAMPLES Castings weighing about 75 grams were melted under vacuum. The charges were made up of ingot iron, copper cathodes from Laurel Hill, and refined silicon supplied by the Electrometallurgical Co. Alundum crucibles were generally used. The exceptions were alloys 77 and 78, which were melted in graphite crucibles. The ingots were annealed at 800°C. for one week, then samples were cut for chemical analysis. Longitudinal sections of the binary alloy ingots were hammered into plates h in. thick. Wherever possible, these plates were homogenized at temperatures ensuring

Jan 1, 1942

By John P. Bryant

Plant nutrients are obtained by plants from both the air and the soil. Carbon dioxide, a gaseous form of carbon and oxygen, supplies the carbon which usually makes up 50% or more of plant structure. Plants are capable of absorbing carbon dioxide directly from the air. Most of this nutrient comes from the air, although some carbon dioxide is absorbed by soil water and taken into the plant as liquid. Growing plants use more water than any other substance. Plant nutrients in the soil dissolve in soil water; soil water entering the plant carries nutrients into the plant structure. Water is then given off into the air as the plant breathes or transpires. The inorganic or mineral portion of the nutrients which plants require comes from the soil. Inorganic or mineral composition of plants is usually less than 5% of their weight, and this mineral requirement, usually lacking in the soil, must be provided by fertilizers. Proper fertilization of a soil to improve its mineral level and productivity is the basis for the fertilizer industry (Thomas, 1960). There are 13 essential plant nutrients which often must be added to soils or plants and are generally considered as fertilizer minerals. These nutrients are divided into the categories: primary minerals (nitrogen, phosphorus, potassium); secondary minerals (calcium, magnesium, sulfur); and micro or trace minerals (boron, iron, manganese, copper, zinc, molybdenum, chlorine). Further, cobalt is often added to fertilizers. Although it is not considered to be an essential plant nutrient, it is essential to animal health and is often applied to forages as a fertilizer constituent. One point of major significance to the fertilizer industry is that not all nutrient carriers supply that nutrient in a chemical form which will be available to the plant. Thus, a product which may be considered a fertilizer mineral may require substantial processing or treatment before it becomes useful as a nutrient carrier. Fertilizer Industry Scope Until about 1900 demands for higher crop yields were met simply by bringing new agricultural lands into cultivation. Since that time great progress has been made in increasing yields through fertilization and improved varieties and cultural practices. The importance of the fertilizer industry to the economy and welfare of the U.S. is widely recognized. [Fig. 1] illustrates the relationship of lime and fertilizers to crop yields. In terms of tons of fertilizer products, the growth of the industry has been phenomenal, particularly between 1950 and 1970. Table 1 shows the increase in fertilizer usage. Primary Plant Nutrients in Fertilizers Primary minerals (nitrogen, phosphorus, potassium) are designated as such because of their significance to plant growth. Practically all soils are deficient in both nitrogen and phosphorus, and most of them are also deficient in potassium. Consequently, these nutrients

Jan 1, 1975

By H. S. Rankin, E. C. Houston

OLIVINE is considered a valuable potential source of metallic magnesium in the chloride electrolytic process. Treatment of olivine with hydrochloric acid can be carried out under conditions that prevent the formation of gelatinous silicic acid, which would inhibit the reaction by forming a covering around the ore particles. It is our hypothesis that the formation of gelatinous silicic acid is avoided by the dehydrating action of the magnesium chloride, which takes up water to form a series of hydrates and leaves the silicic acid in granular condition. Leaching serves to separate the magnesium chloride from the silicic acid and unattacked ore, which can be treated with fresh acid in successive steps until extraction is essentially complete. The leach solution can be purified by the addition of caustic magnesia and the precipitated impurities removed by decantation or filtration. The resulting magnesium chloride contains: Fe, less than 0.001 per cent; Mn, 0.012 per cent; Ni, none. Chlorination[f] of olivine has two major defects: (1) a large part of the chlorine goes to form silicon and iron chlorides, (2) the anhydrous magnesium chloride is held by absorption in the finely divided silica. SUPPLY It is well known that olivine, a silicate of magnesium and iron, is present in large amounts in several localities in the United States. The largest deposits occur in the southeast and on the Pacific Coast.1 The southeastern deposits were surveyed by Lewis2 in 1896 and by Hunter3 in the period 1933-1940. It is estimated that high-grade olivine, conveniently located with regard to transportation and power, is present in excess of 230 million tons above local drainage level in western North Carolina and north Georgia. PREVIOUS TECHNICAL WORK In the past few years, olivine has attracted considerable attention in the refractory field. In the chemical processing industry, however, it has long been thought axiomatic that the cost of processing silicates is an economic barrier to their utilization, especially where more reactive minerals, such as carbonates, oxides or salts, are available. This attitude is not entirely justified in connection with olivine. Unlike most silicates, olivine is readily attacked by acids, chlorine and other reagents without resorting to fusion to break down the silicate structure. Olivine has been suggested as a raw material for making epsom salt by roasting with pyrites.4 Other processes include acid treatment5 and digestion with calcium chloride.6 Recently a small plant was built near Webster, N. C., for making epsom salt from olivine by treatment with sulphuric acid. This plant is now in commercial operation, producing approximately two tons per day. Olivine is also receiving attention from the fertilizer industry as an inexpensive source of soluble magnesium.

Jan 1, 1942