Search Documents

By J. Greenspan

The anisotropy of fracture and slip, that is, the brittleness and ductility of the beryllium single crystal, is characteristic also of po1ycrystalline beryllium in which the grains are oriented in a preferred manner. Beryllium with grain orientations resulting from hot working either unidirectionally or bidirectionally is ductile or brittle in directions given by the anisotropy and orientation of the grains. Textures developed from various hot-working sequences are given, and tensile results are correlated with textures. Not only texture, but fine grain size is necessary for obtaining high tensile elongation. Ultimate tensile strength and elongation are both correlated with grain diameter. Of particular interest is the case in which unusually high tensile elongations of 30 to 40 pct are obtained when basal planes are oriented to carry THE beryllium crystal (of nominal purity) is probably unique among metals with respect to its unusually acute anisotropy of slip and fracture. While extensive slip can occur on the system (1010) [ll20] starting at about 19,000 psi, the (0001) plane is particularly vulnerable to fracture at 4500 psi or less. Fracture occurs also on the (11zo) plane at about 26,000 psi.1"3 Further, there seems to be no other slip System which contributes significantly to

Jan 1, 1960

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By Charles M. Brown, Russell Franks, W. O. Binder

Occasionally in the application of the austenitic chromium-nickel steels to corrosive conditions, failures have occurred by cracking without serious general over-all attack of the metal. As pointed out by Foyt and Scheil(1),2 and by Scheil, et al.(2) as well as by Hodge and Miller(3), the stress-corrosion failures that have occurred have been limited in number, and have taken place only when the steels were exposed to certain corrodents. These investigators have stated that while stress- corrosion cracking can be intergranular in nature and originate at the grain boundaries of the austenitic chromium-nickel steels, it can also take place in trans- granular fashion. They have shown that the cracking may be either initiated at the grain boundaries and may propagate along grain boundaries for some distance and then suddenly extend across grains, or it may begin in a transgranular fashion and suddenly proceed along grain boundaries until the cracking stops. Their data further show that when austenitic stainless steel is subject to intergranular attack, stress will concentrate and cause cracking in service. These investigators have studied the effect of the metals titanium and columbium which are added to the steels to impart immunity to intergranular attack, and molybdenum which is added to improve resistance to general corrosion.

Jan 1, 1945

By Herbert Clark Hoover, Lou Henry Hoover

IN the last book I have explained the methods of delimiting- the meers along each kind of vein, and the duties of mine officials. In this book1 I will in like manner explain the principles of underground mining and the art of surveying. First then, I will proceed to deal with those matters which pertain to the former heading, since both the subject and methodical arrangement require it. And so I will describe first of all the digging of shafts, tunnels, and drifts on venae profundae; next I will discuss the good indications shown by canales2, by the materials which are dug out, and by the rocks ; then I will speak of the tools by which veins and rocks are broken down and excavated ; the method by which fire shatters the hard veins ; and further, of the machines with which water is drawn from the shafts and air is forced into deep shafts and long tunnels, for digging is impeded by the inrush of the former or the failure of the latter ; next I will deal with the two kinds of shafts, and with the making of them and of tunnels ; and finally, I will describe the method of mining venae dilatatae, venae cumulatae, and stringers.

Jan 1, 1950

By Roy McLellan

THE slags derived from the smelting of lead and copper ores are composed essentially of silicates. The problems arising from the smelting of these ores consequently involve the study of silicate fusions. In the absence of specific knowledge concerning the compounds occurring in slags, it has been the practice of metallurgists to treat them in terms of their total chemical composition. Slags have been classified as monosilicates, bisilicates, sesquisilicates, and subsilicates according to the relative amounts of oxygen in the acid and basic radicles of the hypothetical salt produced. While this has been a useful guide to metallurgists in computing the furnace charges, it falls far short of a basis for the scientific investigation of slags. In order to understand the nature of a slag as a whole it is necessary to learn the physical and chemical properties of the mineral compounds which go to make up that slag. The efficiency with which an ore is smelted in a furnace depends primarily on the physical properties of the compounds formed during the operation. When the melting points and fields of stability of each of the mineral compounds in slags have been established, it will be possible to determine the properties of any given slag by examining the nature and amounts of its mineral constituents.

Jan 1, 1930

By Herbert Clark Hoover, Lou Henry Hoover

SINCE I have written of the varied work of pre- paring the ores, I will now write of the various methods of smelting them. Although those who bum, roast and calcinea the ore, take from it something which is mixed or combined with the metals ; and those who crush it with stamps take away much ; and those who wash, screen and sort it, take away still more; yet they cannot remove all which conceals the metal from the eye and renders it crude and unformed. Wherefore smelting is necessary, for by this means earths, solidified juices, and stones are separated from the metals so that they obtain their proper colour and become pure, and may be of great use to mankind in many ways. When the ore is smelted, those things which were mixed with the metal before it was melted are driven forth, because the metal is perfected by fire in this manner. Since metalliferous ores differ greatly amongst themselves, first as to the metals which they contain, then as to the quantity of the metal which is in them, and then by the fact that some are rapidly melted by fire and others slowly, there are, therefore, many methods of smelting. Constant practice has taught the

Jan 1, 1950

By Milton Glicken

THE airborne geophysicist is a busy man these days. In his plane he may have the airborne magnetometer, the airborne scintillation counter, and the airborne electromagnetic surveying system. Each of these is an independent tool, but all require additional auxiliary equipment for locating the aircraft in space: recording altimeters and Shoran or aerial cameras. Now there is still another piece of equipment, the airborne magnetic gradiometer, an accessory to the magnetometer. To understand its uses, consider the function of the magnetometer itself. Aside from detecting magnetic ore, the airborne magnetometer finds greatest use in spotting intrusions of igneous material. Where there is enough contrast in magnetic susceptibility of igneous rock and adjacent formations, it outlines the intrusion. Certain minerals also influence the magnetometer directly, but with the exception of magnetite and possibly one or two others, their effect is weak and can be detected only when there is sufficient ore and the magnetometer flight passes very close to it. An igneous intrusion of infinite depth with vertical sides is represented on a magnetometer record by an anomaly, as in Fig. 1. Amplitude of the high depends on susceptibility contrast of the igneous rock. Generally speaking, the edge of the intrusion lies below the point of inflection of the curve, and this point, where the curvature changes from positive to negative on the magnetometer profile, would be near A in Fig. 1, with a counterpart, of course, on the other side. Location of the contact is one of the principal objects of the survey, but finding the precise point is not always easy, as inspection of the curve near A will show. Mineralization is often found at the contact zones, as at B. Magnetic effects, if detected, may be small, as in B', and when superimposed on the anomaly due to the instrusion they are very difficult to discern and analyze. Furthermore, if these small fluctuations are to be perceived by the magnetometer the vertical scale should be large. This increases the slopes of the anomaly and makes detection of small deviations and inflection points even more difficult. The airborne magnetic gradiometer was designed to help overcome these difficulties. What it presents is the first derivative of the magnetometer record with respect to time, that is to say, the slope at any point. Fig. 2 represents an actual magnetometer record (solid line) with the corresponding gradiometer record (dashed line) superimposed. Both records read from right to left. Vertical lines on the original magnetometer record are automatic steps designed to keep the pen from going off scale. The slope of any curve is greatest at the point of inflection or point where the curvature changes sign, and this point is a maximum (or minimum) on the gradi- ometer. The chief advantage of the gradiometer is that maxima or minima are much easier to see and to locate precisely; hence an accurate location for the point of inflection can easily be found. Note that points C and D are more sharply defined than C and D'. Similarly the small fluctuations of the original record, so important to the interpreter, are far more clearly shown at E, F, and G, than on the original record at E', F', and G'. Though not necessarily highs and lows on the gradiometer, they do show up clearly what would take a painstaking analysis to detect on the original magnetometer record. Will the gradiometer have a particular configuration which indicates an orebody? Not necessarily. The total intensity curve, or original magnetometer record, can display an orebody in various ways, depending on dimensions, orientation, latitude, and composition, as well as on direction, flight height, and instrumental sensitivity of the traverse. Where the total intensity can take on so many different shapes the gradiometer must vary too. It is generally recognized that interpretation of total intensity magnetometer records requires an expert analysis; the gradiometer can be of considerable assistance to the expert but it does not replace him. Mechanism of the gradiometer is simple. A Leeds & Northrup recorder in the aircraft records the magnetic gradient simultaneously with the total intensity, which is on another recorder. Fiducial marks are put on both records simultaneously and the speed of the paper through the recorders is kept the same on both. This makes it possible to place one record over the other for direct comparison. In the laboratory the flights are positioned on a map. Maximum and minimum points on the gradiometer, which can then be posted on the map at their proper locations, may be expected to fall along a trend crossing the direction of flight. Trends should indicate the edge of an intrusion, or some other important features, and when superimposed on the total intensity contour map help greatly to locate the points of inflection, or line of zero curvature.

Jan 1, 1956

By L. C. Brown, S. K. Behera

The diffusion rate in Ag-Sb couples is sensitive to con~pressive load with the width of Ag3Sb, the only phase present in the diffusion zone, increasing with stress up to 800 psi and remaining constant above this. Kirkendall marker experiments show silver to diffuse much faster than antimony in Ag3Sb and incipient porosity may therefore develop at the Ag/Ag3Sb interfnce restricting the transfer of atoms from the silver into the diflusion zone. Application of compressive stress reduces the tendency for porosity to develop and so increases the growth rate. In a recent paper Brown et al.1 observed a significant increase in the thickness of Cu2Te in Cu-Te diffusion couples on application of a compressive stress as low as 20 psi. Similar stress effects have also been observed in the Fe-A1,2 Al-u,3 arid cu-sb4,5 systems. It has been suggested that the increase in growth rates of intermetallic phases in these systems is due to a decrease in the amount of Kirkendall porosity with applied stress. In the present paper, results are presented of the effect of compressive stress on diffusion in Ag-Sb, together with a detailed examination of the Kirkendall effect. The Ag-Sb phase diagram6 shows that antimony has a moderate degree of solid solubility in silver, 5.7 at. pct at 350°C, but that there is essentially no solubility of silver in antimony. There are two intermediate phases— (hcp7) from 8.8 to 15.7 at. pct Sb and Ag3Sb (orthorhombic8) from 21.8 to 25.9 at. pct Sb. EXPERIMENTAL Diffusion couples were prepared from fine silver of 99.95 pct purity and from antimony of 99.7 pct purity. Both the silver and antimony were produced in the form of discs 1/2 in. in diam by approximately $ in. thick, with surfaces ground flat to 3/0 emery paper. Diffusion anneals were carried out in the apparatus previously described.1 A compressive load was applied to the diffusion couple through a lever arm system, with a reproducibility estimated to be ±10 psi. All runs were carried out in a protective hydrogen atmosphere. Following the diffusion anneal specimens were sectioned and polished and the width of the diffusion zone was measured metallographically. Composition profiles were measured using an electrostatically focused electron probe with a spot size of 10 , counting on Sb L radiation. Corrections for matrix absorptiori and fluorescent enhancement9 were not required. S. K. BEHERA, formerly Graducate Student, Department of Metallurgy, University of British Columbia, is now Postdoctoral Fellow, Whiteshell Nuclear Laboratories, Atomic Energy of Canada Ltd., Pinawa, Manitoba. L. C. BROWN, Junior Member AIME, is Associate Professor, Department of Metallurgy, University of British Columbia, Vancouver, B.C., Canada. Manuscript submitted June 14, 1968. IMD RESULTS Fig. 1 shows an electron probe traverse of a typical diffusion zone. In all couples examined only one intermediate phase was observed and the composition of this phase, 23 wt pct Sb, was in good agreement with the composition of Ag3Sb, 23 to 28 wt pct Sb. The presence of this phase was confirmed by X-ray diffraction of filings taken from the diffusion zone. The probe traverses showed no detectable solid solubility in either the silver or the antimony although the phase diagram indicates that some antimony, up to 6.5 wt pct pct Sb, should be in solid solution in the silver. However the width of this portion of the diffusion zone would be expected to be very small in view of the low diffusion coefficient in the silver, 4 x 10-l6 sq cm per sec at 350°C, 10 compared with that in the Ag,Sb, estimated as 3 x 10-8 sq cm per sec in the present work, and this region would therefore not be expected to be seen in the probe traverse. Application of stress resulted in a significant increase in the width of the diffusion zone, Fig. 2. At 350°C, the thickness of Ag3Sb increased from 250 at 0 psi to 400 p at the limiting stress of 800 psi, indicating an apparent 150 pct increase in the diffusion coefficient. Similar behavior was also observed at 400°C, indicating that the stress effect is not characteristic of just one temperature. The growth of Ag3Sb at 350°C and at various stresses is shown in Fig. 3. In every case the growth rate was parabolic indicating diffusion control. The kinetic curves all passed through the origin showing that delayed nucleation of Ag3Sb was not responsible for the stress effect and that it was a real growth effect. A series of tests were carried out in which diffusion was allowed to take place at a lower stress following an initial high stress diffusion anneal. Speci-

Jan 1, 1969

By G. Bhat, J. F. Libsch

lsoembrittlement curves depicting the influence of time and temperature in the range 800' to 1260°F (425' to 680°C) on the development of embrittlement in a commercial chromium alloy steel and a commercial molybdenum alloy steel are presented. Two distinct regions of embrittlement occur in the chromium alloy steel: I—at 800' to 1000°F (425' to 540°C) and 2—in the region just below the lower critical temperature. Embrittlement is most pronounced at 800' to 1000°F, decreasing very rapidly with increasing temperature above this region, only to increase again as the lower critical temperature is approached. The data suggest two distinct modes of embrittlement with possible superposition of the two modes at extended embrittling times in the temperature range 1100° to 1150°F (590' to 620°C). While the molybdenum alloy steel shows little susceptibility to embrittlement at 800' to 1000°F (425' to 540°C), considerable embrittlement may occur just below the lower critical temperature. THE subject of temper embrittlement in alloy steels has received considerable attention in the last few years. Points of view on the mechanism of embrittlement differ, however, resulting in part from the incompleteness of the data developed and in part from the speculation regarding the susceptibility of plain carbon steel to temper embrittlement. Libsch, Powers, and Bhat1 carried out short-time embrittling treatments on an AISI 1050 steel and demonstrated that hardened plain carbon steels are quite susceptible to embrittlement when tempered in the range from 850°F (455°C) to the lower critical temperature. The isoembrittlement diagram,' representing the embrittling characteristics of this steel, is reproduced in Fig. 1. It is evident from the shape of the curves shown that embrittlement in plain carbon steel increases progressively with both temperature and time in the embrittling range. A comparison of the isoembrittlement diagram for AISI 1050 steel with that presented by Jaffe and Buffum' for an SAE 3140 steel shows that up to 930°F (500°C) the isoembrittlement characteristics of the plain carbon steel are similar to those of SAE 3140 steel, although the embrittlement is much more severe in the latter steel. Above 930°F (500°C), the rate of embrittlement in the plain carbon steel increases continuously with increasing temperature; whereas, in the SAE 3140 steel, the embrittlement rapidly decreases. The influence of alloying elements upon embrittlement during tempering thus appears to cause a decrease in embrittlement above the region of maximum embrittlement, i.e., 850" to 1000°F. The question naturally arises as to what effect individual alloying elements have upon the embrittling characteristics of the plain carbon steel. Current knowledge on the influence of alloying elements on temper brittleness may be found in the review papers of Hollomon" and Woodfine. Hollo-mon," from the results of other investigators, has shown that, in general, the amount of embrittlement increases with increasing alloy content (except for molybdenum and possibly tungsten and columbium). Jaffe and Buffum," by a comparison of the embrittlement in a plain carbon steel with that of a SAE 3140 steel postulated that the presence of alloying elements in moderate amounts tends to retard the development of temper brittleness. It is difficult to determine what effect chromium has upon temper brittleness, since most of the information available has been based on the combined effect of other elements with chromium, particularly nickel and manganese. However, Wilten, and recently Jolivet and Vidal,' Vida1, and Woodfine have reported that chromium steels are temper brittle, that the embrittlement is reversible with a maximum rate of embrittlement at approximately 975°F (525"C)," and that the susceptibility increases with increasing amounts of chromium. Taber, Thorlin, and Wallacel" have found a large embrittling effect with increasing chromium content in a medium C-Mn-Ni steel. But Hultgren and Chang," from their experiments conducted on synthetically prepared ternary Fe-C-Cr alloys, could not conclude that these alloys are susceptible to temper embrittlement. However, on addition of manganese or phosphorus, these Fe-C-Cr alloys became susceptible, from which fact they concluded that the embrittlement developed in chromium-bearing Fe-C alloys is due chiefly to the presence of these elements. Considerable data are available to show that molybdenum decreases the susceptibility of steel to temper embrittlement. However, its effectiveness in preventing or decreasing embrittlement appears limited to its presence in small amounts. Vidal" has shown that a plain 2 pct Mo steel was susceptible. Hultgren and Chang" also have shown that molybdenum additions in excess of 2 pct to synthetically prepared Ni-Cr steels did not prevent embrittlement. Jolivet and Vidal' and Lea and Arnold found that molybdenum reduced temper brittleness. Lea and Arnold further stated that molybdenum decreased the rate of embrittlement rather than the total amount of embrittlement, whereas Preece and Carter" have shown that the presence of molybdenum greatly reduces the equilibrium extent of the change at a given temperature but does not appear to influence the rate of embrittlement. There appears to be very little information as to how molybdenum by itself affects the temper brittleness susceptibility of a plain carbon steel.

Jan 1, 1956

By Louise Barton Freeman, Iley B. Browning, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By George L. Montgomery

In a recent article Heckler, Elias, and woods1 have described an automatic computer technique for plotting of pole figures. To anyone who has constructed pole figures manually from raw X-ray data, the development of computer plotting techniques has been a very welcome development. The purpose of the present note is to describe an alternative computer plotting method which, if somewhat less precise than the method described by Heckler et al., has the advantages of being faster and of not requiring the availability of a plotter. The plot is made directly by the printer of the terminal system and, by its nature, has a good deal of visual impact. Each character of output symbolizes a level of intensity. For example the numerals 1 to 9 might represent intensities referred to some reference obtained from a randomly oriented sample. Should more levels be required (this is seldom necessary) alphabetic or other characters may be used in addition. When these are arranged in the proper fashion, the result is a pole figure such as is shown in Fig. 1. It is the purpose of the computer program to transform the data and carry out the arrangement in a suitable manner. The computation is carried out on a line by line basis in order to reduce the amount of storage required and thus keep the program "small". It is, thereby, well within the limitations of the time-sharing systems which are becoming increasingly available. The inaccuracies introduced are slight and the plot can easily be made as precise as the technique used to collect the data. Comparison of pole figures produced by this method with those constructed manually shows a high degree of equivalence. To the present, the technique has been applied to reflected X-ray data only. X-ray data are collected in a manner identical to that described by Heckler et al. That is, as the goniometer rotates the specimen, a series of counts, accumulated over a preset time, is recorded. The method by which the proper symbol, representing an intensity level, is assigned to each print position is up to the ingenuity of the programmer. Perhaps the simplest method is to section the stereograph in the fashion of a polar net, and to assign all print positions lying within each segment a symbol representing the level of intensity recorded at the data point nearest to the center of the segment, see Fig. 2. The number and arrangement of the segments are selected to conform more or less with the number of accumulated counts and the geometry of the goniometer path used to collect them. Since the angular distance between accumulated counts is usually not infinitely controllable, it is impossible to locate one reading within each segment and, at the same time, maintain symmetry in the sectioning of the stereograph. This latter requirement is essential to keep the computer program simple and flexible. As an expedient it was found that the number of data points could be increased to conform with the number of segments, with very little loss of

Jan 1, 1969

By Iley B. Browning, Louise Barton Freeman, Coleman D. Hunter

During 1942, production of oil in Kentucky reached a total of 4,169,163 bbl. of which 1,807,809 bbl. came from eastern Kentucky. This was more than a million barrels less than in 1941, owing partly to the low price of crude oil, which almost eliminated wildcatting, and partly to spacing regulations, which limited the number of wells drilled in small, shallow pools where the pressures are not sufficient to maintain maximum recovery in widely spaced wells. In eastern Kentucky much of the oil was produced from outliers of the Mauch Chunk series at the disconformable contact of the Mississippian and Pennsylvanian. Although wells producing from this horizon, known as the Maxon, are sprinkled over the entire area, the greatest concentrations are in Martin, Floyd, Knott and Pike Counties. A new 30 to 40-bbl. well has been completed in this formation in ,Pike County, where the carbon ratio is so high that ordinarily oil would not be expected. Pike County is one of the largest producers of Maxon gas, and the offset well to this oil well produced gas. Of the 412 gas wells drilled in Pike County, 12.2 per cent produced gas from the Maxon horizon. During 1942, the old Menifee " Cornif-erous" field, the Mariba-Denniston field, was redrilled between old wells, and although it did not produce any large amount of oil it did contribute 2018 bbl. In the oldest oil field in eastern Kentucky, the Ragland pool, operators are cleaning out abandoned wells and are using this oil for fuel oil. There is a possibility that some of this may be used in the future as distilled fuel oil. Eight wells were completed in 1942 in the Jackson County gas field. The development of Jackson County, which was started in 1934 and in which commercial quantities of gas were encountered at a depth of 1100 to 1200 ft., has become of importance in 1942 with the completion of eight wells, making a total of 24 commercial producing wells with an average rock pressure of 140 lb. At this time the gas is not being marketed. In the last year it has been found that these wells, which produce from the Niagaran dolomite ("Cornif-erous"), respond to acidizing and the production has been thus greatly increased. There has been less development in Estill and Lee Counties than for several years. Two wells were drilled in Greenup County, one of which had a show of oil in the Berea sandstone. One deep test, drilled by the Owens-Libbey-Owens Co. in Lawrence County, was dry. This well was drilled to a depth of 4975 ft. into the top of the Clinton shale sequence. Of the 202 wells completed in Floyd, Martin, Knott and Pike Counties, 187 were gas wells, 3 oil wells and 12 dry holes. In Floyd County 66 per cent of the gas production was from the Devonian-Mis-sissippian black shales, 53 per cent in Martin, 79 per cent in Knott and 65 per cent in Pike. This is probably the largest continuous gas field east of the Mississippi

Jan 1, 1943

By J. Murray Riddell

The method of treating hazards wherein value is decreased, is cited by R. D. Parks. Quite properly, the theory of probabilities is made use of when multiple hazards are under consideration. E. F. Fitzhugh, Jr. $ deals with the enhancement phase graphically and uses percentage of expectancy as derived by a study of conditions and the selection of a chance factor. It is believed that both of the authors referred to fully recognize the part which human judgment plays, and as coupled with experience, training, and the application of the theory of probabilities; in that respect the composer of this paper is in accord. Within the past year, the task of arriving at a mathematical method for handling the enhancement phase, and, additionally, coupling the negative and positive phases, was explored. In citing the hazard, or negative phase, reference is made to the text by Parks. Types of Items far Consideration On the hazard, or negative, side some of the common items to be considered are: 1. Subsidence and resulting damage. 2. Flo wage of water above that anticipated. 3. Geological. (a) Decline in quality of probable ore, and/or (b) Decline in quantity of probable ore. 4. Depressed economic conditions. 5. Litigation. Similarly, on the enhancement, or positive, side common items to be considered are: 1. Flo wage of water below that estimated. 2. Geological. (a) Increase in quality of probable ore, and/or (b) Increase in quantity of probable ore. 3. Elevated economic conditions. 4. Litigation. 5. Technological advance in the art. Tn all of the above items no consideration is given to placing a value on, or giving consideration to, possibilities. For example, referring to Table 1, the estimated normal present value (Vp) of a property, exclusive of risk consideration, is taken as $100,000. If subsidence affects the usefulness of the shaft, the present value of the property will decrease to $60,000, and it is judged that there is a 1 in 4 chance that the shaft will be impaired;, consequent.ly, if subsidence took place, the present value would be reduced ($100,000-$60,000) $40,000, but since the chance is 1 in 4, the allowable reduction would be only one-fourth of $40,000, or $10,000, or a discount of 10 pct (hazard factor) of the original value; the related safety factor is taken as unity minus 0.10, or 0.90. Thus, the original Vp, $100,000, multiplied by the safety factor ($100,000 X 0.90) gives $90,000, which is the adjusted present value of the property in this single instance. Additionally, there is a water hazard, which, if encountered, will reduce the present value to $85,000. The chance is 1 in 3. Following through with the same reasoning as shown above, the derived safety factor will be 0.95. To arrive at a single multiplying factor which will express the combined risks, the two safety factors are multiplied together, 0.90 X 0.95 = 0.855. That factor when multiplied by the origirial Vp will give the adjusted, and

Jan 1, 1950

By E. Stamboliadis

Dithiophosphates are reaction products of phosphorous pentasulfide with various organic compounds such as phenols, alcohols, mercaptans, dioalcohols, amines, and nitrides. The products with alcohols are commercially known as "aerofloats" and these are investigated in this presentation. It appears that the formation of insoluble metal dithio phosphates is responsible for their collecting properties with minerals." In this aspect they are very similar to xanthates.3 The solubility of metal dithiophosphates depends on the number of carbon atoms in the organic chain of the corresponding alcohol. An empirical mathematical model is presented here. It allows one to predict the number of carbon atoms necessary to ensure that a certain metal dithiophosphate will form at a selected pH value of the water solution. The Nature of Dithiophosphates Dithiophosphoric acid is the product of the reaction of phosphorus pentasulfide with an alcohol, as shown in the following equation: [P2S3 + 4 ROH - 2 (RO)2 PS2H + H2S (1)] where R stands for a hydrocarbon chain. The acid so produced can be neutralized by a base to produce the corresponding salt as shown in the following: [(RO), PS2H + NH- (RO)2 PS, NH,. (2)] In this aspect dithiophosphates are similar to xanthates, the only difference being the substitution of the tetravalent carbon atom in the xanthate polar group by a pentavalent phosphorus atom in the dithiophosphate group. This difference implies at least two characteristics: (1) that there are two hydrocarbon chains associated with the polar group so that an increase in the number of carbons of the single chain is expected to have a pronounced effect on the flotation properties, and (2) that the bond between the sulfur and the central atom is stronger than in the xanthate group. This probably leads to a decrease in both the polarizability of the electronic cloud of the sulfur and the interaction with cations.3 However, what is lost in the dithiophosphates by having a weak polar group can be gained by an increase in the number of carbons as will be seen later. Taking into account the size of the atoms involved in a dithiophosphate molecule, as listed in Table 1, It is possible to draw an approximate diagram of its structure as shown in [Fig. 1]. It is assumed here that the length of the single hydrocarbon chain is equal to that of the corresponding alcohol. Preparation and Purification Acid dithiophosphates can be prepared, as previously mentioned, in accordance with Eq. 1. The rate of this reaction is too slow at room temperature and can be improved by increasing the temperature to about 60° or 80°C7 or by evacuating the system. In our investigation evacuation was performed by a water aspiration pump. The dithiophosphoric acid so produced is liquid and dissolves in the alcohol. At the end of the reaction the product is filtered from the remaining P2S3; and dissolved in petroleum ether. By blowing anhydrous ammonia gas into the ether phase the ammonium salt forms as a white precipitate and can be sepa-

Jan 1, 1977

By A. Andreas

New Mexico established an annual record by producing 38,897,741 bbl. of oil during 1940. This was approximately 6 per cent greater than the 1939 production of 36,746,840 bbl. The daily average produc-tion was 106,569 bbl. New Mexico retained its position as the seventh oil-producing state. The recommendations of the United States Bureau of Mines were followed by the Oil Conservation Commission in setting the monthly state allowable. At the beginning of the year the average top allowable for each qc-acre unit was 40 bbl. and at the close of the year it was 36 bbl. Remedial work by the operators has been extremely beneficial and satisfactory in reducing the gas-oil ratios in various fields. Gas formerly blown into the air is now being processed by numerous casinghead plants. The Oil Conservation Commission, with the full cooperation of the Proration Office and operators, has taken bottom-hole pressure surveys and has done considerable remedial work in various fields. Two new oil fields and one gas field were discovered in New Mexico during 1940. Numerous extensions to the existing fields were made. Some of these were definitely wildcats in the same townships designated as fields and some, although called extensions, were more than 3 miles from production. Lea County continued to be the largest oil-producing county in the state, with a production of 33,976,394 bbl. It had the largest number of completions during 1940, with 303 oil wells, 9 gas wells and 13 dry holes—a total of 325 wells. Eddy County was the next most active county, with 239 completions, of which 163 were oil wells, 8 gas wells and 68 dry holes. It produced 4,405,158 bbl. of oil during the year. The increased activity in Eddy County and the completion of a large number of producing oil wells have created a transportation problem that can be solved only by additional pipe-line facilities. During the year Eddy County was unable to produce 1,500,000 bbl. of its allowable oil, because there was no pipe-line outlet. There were 601 wells completed in New Mexico in 1940, of which 478 were oil wells, 22 gas wells and IOI dry holes. This was a decline of approximately 9.5 per cent in the number of completions compared with 1939, when 659 wells were drilled. Southeastern New Mexico Lea County.—The largest producing field in Lea County was the Monument field, with 6,894,475 bbl.; followed by Eunice with 6,559,348 bbl. and Vacuum with 4,743,065 bbl. The Hobbs pool, which for years was the largest producing field in the state of New Mexico, was fourth with 3,790,477 bbl. The Vacuum pool was the most active area, having 68 completions, of which 67 were oil wells and one was a dry hole. Only one new field was discovered in Lea County during 1940; the discovery well was in the Caprock area, the Livermore State No. I, in the SE. 1/4 SE. 1/4 sec. 30, T. 12 S, R. 32 E. This well was drilled to a

Jan 1, 1941

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By Arch J. Alexander

Coal is produced, in commercial quantities, in thirty-five of the fifty-five counties of West Virginia. Oil and gas are produced, commercially, in forty-two counties. So, you may readily see that coal, oil and gas arc closely related as to production areas. Many of the West Virginia coal mines are studded with oil and gas wells, as drilling has been done in thirty-two of the coal bearing counties. When the drilling of oil and gas wells was placed under the regulatory control of the Department of Mines on June I, 1929, it was estimated, by the State Geological Survey, that 64,000 wells had been drilled in West Virginia and that 34,000 wells were then being operated as oil and gas producers. No records of many of these remaining 30,000 abandoned wells exist and some of them remain a standing menace to safety as our coal extraction continues. Of a total of 13,100 new wells drilled since June 1929, approximately 5200 have been drilled through coal measures. Approximately 7000 wells, which were drilled through coal measures, have been abandoned in the same period of time. Many of these wells were drilled prior to the enactment of the oil and gas laws. Prior to the enactment of the Oil and Gas Law, which established the Oil and Gas Division of thc Department of Mines in 1929, there had been several mine ex-plosions attributable to cutting into un- charted wells and the improper plugging of other wells. The most serious explosion was that of Mines No. 47 and No. 49 of the Consolidation Coal Co. in Marion Co., when one of the so-called plugged wells leaked or seeped through some 80 ft of strata to the coal bed elevation, filling the mine with gas, the gas being ignited, killing a good many men and wrecking two coal mines. Legislation, to combat well hazards to coal mines, was slow in coming. In 1928, R. M. Lambie, then Chief of the Dept. of Mines, got sufficient support from coal, oil and gas interests to get the legislature to pass our present oil and gas laws. These statutes not only protected the coal industry but went a long way toward conserving the oil and gas resources of our state. Before drilling for oil or gas on any tract of land, known to be underlaid with one or more workable seams of coal, the well operator is required to submit a map of the area showing the location of the proposed well, and to send a copy to the Dept. of Mines and a copy to the coal operator. If no objections to the location of the proposed well are made by the coal operator within ten days, a drilling permit and a number for the well are then issued and work may proceed. If, however, the location of the proposed well is objected to by the coal operator, on the grounds that the location of the well will interfere with present mine operations, projected workings, or otherwise cause a dangerous condition, the operator may file a written objection with the Dept. of Mines.

Jan 1, 1949

By Arch J. Alexander

COAL is produced, in commercial quantities, in thirty-five of the sty-five counties of West Virginia. Oil and gas are produced, commercially, in forty-two counties. So, you may readily see that coal, oil and gas are closely related as to production areas. Many of the West Virginia coal mines are studded with oil and gas wells, as drilling has been done in thirty-two of the coal bearing counties. When the drilling of oil and gas wells was placed under the regulatory control of the Department of Mines on June I, 1929, it was estimated, by the State Geological Survey, that 64,000 wells had been drilled in West Virginia and that 34,mo wells were then being operated as oil and gas producers. No records of many of these remaining 30,000 abandoned wells exist and some of them remain a standing menace to safety as our coal extraction continues. Of a total of 13,100 new wells drilled since June 1929, approximately 5,200 have been drilled through coal measures. Approximately 7,000 wells, which were drilled through coal measures, have been abandoned in the same period of time. Many of these wells were drilled prior to the enactment of the oil and gas laws. Prior to the enactment of the Oil and Gas Law, which established the Oil and Gas Division of the Department of Mines in 1929, there had been several mine explosions attributable to cutting into un- charted wells and the improper plugging of other wells. The most serious explosion was that of Mines No. 47 and No. 49 of the Consolidation Coal Co. in Marion Co., when one of the so-called plugged wells leaked or seeped through some 80 ft of strata to the coal bed elevation, filling the mine with gas, the gas being ignited, killing a good many men and wrecking two coal mines. Legislation, to combat well hazards to coal mines, was slow in coming. In 1928, R. M. Lambie, then Chief of the Dept. of Mines, got sufficient support from coal, oil and gas interests to get the legislature to pass our present oil and gas laws. These statutes not only protected the coal industry but went a long way toward conserving the oil and gas resources of our state. Before drilling for oil or gas on any tract of land, known to be underlaid with one or more workable seams of coal, the well operator is required to submit a map of the area showing the location of the proposed well, and to send a copy to the Dept. of Mines and a copy to the coal operator. If no objections to the location of the proposed well are made by the coal operator within ten days, a drilling permit and a number for the well are then issued and work may proceed. If, however, the location of the proposed well is objected to by the coal operator, on the grounds that the location of the well will interfere with present mine operations, projected workings, or other- wise Cause a dangerous condition, the operator may file a written objection with the Dept. of Mines.

Jan 1, 1948

By J. P. Heller, H. B. Bradley, A. S. Odeh

It is an accepted procedure to represent oil field displacement problems in which the pressure is relatively constant by a potentiometric model. Variations in reservoir permeability thickness product are represented in the model by proportional variations in electrolyte depth. It is shown that significant errors are present wherever these variations are of such magnitude that the consequent differences in the electrolyte depth in the model or any regions therein are appreciable in comparison with their respective horizontal dimensions. To demonstrate the order of magnitude of this error, a hypothetical linear oil field in which permeability varies linearly with distance was treated both analytic.ally and by potentiometric model. The results obtained from the model are compared with the exact solution for various configurations of linear geometry. Deviations in flow times up to 11 per cent were observed. It is confirmed that these discrepancies can be reduced by increasing the areal scale and/or decreasing the vertical scale of the model. It is the purpose of this work to assist in the design of potentiometric models by indicating the relationship between this error and the chosen scale factors. INTRODUCTION The fundamental geometrical criterion which determines whether the pressure distribution in an oil or gas reservoir may be simulated in a conventional potentiometric model is the requirement that all reservoir parameters be constant along any vertical line between its upper and lower boundaries. This situation never obtains exactly; nevertheless, it is usually assumed that there is no permeability stratification within the section of interest, that all wells completely penetrate the sand, that there are no gravitational effects, and that variations in thickness of the sand are small compared to the horizontal extent of the field. In these ways the reservoir problem is reduced to two dimensions in which there is no variation of pressure in the vertical direction within the limits of the sand. Variations in sand thickness and/or horizontal pesmeability may be taken into account as described by Muskat, by considering the fluid conductivity of the reservoir in its horizontal plane to be proportional to the product of permeability and sand thickness. If the variations in sand thickness are small compared to the horizontal dimensions of the reservoir, then it is a good approximation to consider the reservoir problem to be essentially two dimensional. The same approximation, however, is made in the simulation of the assumed two-dimensional reservoir by the electrolytic model. The model, if it is to take into account variations of permeability-thickness product, must of necessity be made in three dimensions, that is, with variable depth. Most potentiometric model studies and theoretical treatments reported in the literature to date2,3,4,5,6,7,8 are those in which either an average permeability was used or a constant permeability was assumed. This is understandable since detailed permeability data are not usually available for the majority of reservoirs. Many investigators have recognized that the failure to incorporate permeability variations within a reservoir in model studies leads to serious error in predictions made

Jan 1, 1957