Search Documents

By D. W. Hutchinson, W. W. Wen, A. A. Terchick, J. C. Anderson

It is estimated that approximately 3% of the raw coal processed today in coal preparation plants throughout the nation will ultimately report to slurry-tailing disposal (Anderson, 1975). The usual disposal method is to pump refuse slurry containing - 48 mesh (300 pm) refuse into dams or impoundments constructed of coarse refuse. The failure of an impoundment at Buffalo Creek, Saunders, WV (Anon., 1972) resulted in an evaluation of refuse disposal methods by various regulatory agencies as well as coal producers. The result of this evaluation was the promulgation of federal regulations dealing with the construction, operation, and final abandonment of coal refuse disposal area. As a consequence of these regulations, the use of the landfill/impoundment method of disposal became in some cases economically unfeasible or technically impossible. US Steel has studied a number of alternative methods of refuse disposal. During an investigation of mechanical dewatering with a pressure filter, portland cement was added to the slurry to solidify the filter cake. Because of the success of the cement addition, it was decided to study the stabilization of fine coal refuse slurry through use of cement-type additives. The goal of the investigation is to develop a process that will use cement-type additives to solidify the refuse slurry into a form that can be handled and stacked with the coarse refuse, thus eliminating the need for slurry impoundments.

Jan 1, 1982

By Edward Estabrook

THIS paper gives a brief account of the geologic and production problems encountered in the Grass Creek oil field, the methods used in their solution, and the beneficial results obtained from the work. The author wishes to acknowledge the assistance received from J. H. Pearson and Miss Ninettta A. Davis in the collection of the data and the preparation of the cross-sections. Permission for its publication was given by the officials of the Midwest Refining Co. and the Ohio Oil Co. The Grass Creek oil field is located in Ts. 98-99 W., R. 46 N., Hot Springs County, Wyo. The productive area includes about 2 1/2 mi. (4 km.) on the apex of a great anticlinal fold occupying more than 150 sq. mi. Fig. 1 shows the structural contours of the field. Oil was dicovered in the field in June, 1914; development proceeded rapidly and production rose to a maximum in 1918. The marketed production has been approximately as follows: BARRELS BARRELS 1915 94,073.5 1918 2,946,774.27 1916 1,404,183.97 1919 2,000,584.84 1917 2,780,697.51 1920 1,485,080.94 About 350 wells, 800 to 1500 ft. (243 to 457 m.) deep have been drilled to reach the upper oil sands; two companies, the Ohio Oil Co. and the Midwest Refining Co., operate the entire field.

Jan 2, 1922

By Adrian E. Ross

Diamond drilling through caving formations at depths greater than ZOO0 ft has long presented serious difficulty, generally solved either by casing or cementing. Casing is permitted only when the resulting smaller hole is acceptable, and cementing is frequently a problem at depth. A new method that injects cement under pressure at the desired location is an aid in diamond drilling deep holes. DRILLING through caving formations in diamond drill holes at depths greater than 2000 ft has long been a serious problem. These caving formations are normally passed only by casing the hole or by cementing the hole. Casing the hole is possible only when a resulting smaller hole is acceptable. In as much as only a limited number of reductions are economically practical, cementing is frequently considered the only method suitable for solving these problems. Cementing either by pumping a slurry into the hole or by dropping cylinders containing cement has proved satisfactory on holes under 2000 ft. In holes substantially deeper than 2000 ft these methods are not satisfactory, since during the pump- ing process cement separates out, whereas cylinders usually break before the bottom of the hole is reached. A new procedure, the injector method, apparently solves these problems.* With this method, cement is lowered in the hole in a cylinder, the cement being

Jan 1, 1953

By Henry N. McCarl, John J. Dran

The academic community and the larger and more sophisticated mining companies have largely rejected the older mineral valuation methods such as the Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or "safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest in numerous (often nonmining) alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice all militate against the continued use of the older valuation methods, especially for the larger mining companies. Small mining companies and individuals still use these methods largely out of habit and familiarity. The Hoskold Mineral Reserve Valuation Method The Hoskold method was developed prior to the evolution of modern accounting practices and before the days of the corporate income tax. At the time of its development, annual earnings of the firm were represented by the difference between cash revenues and cash expenses and were not subject to taxation by the government. Thus, earnings at that time were equivalent to what is today known as cash flow.

Jan 7, 1974

By John D. Gill

The purpose of this paper is to invite attention away from the obvious. direct monetary costs of oil-field overdevelopment (as distinguished from "social costs") to a consideration of the role played by the exercise of freedom to create even allegedly excessive1 plant facilities in contributing to the maintenance of equilibrium in the wholc economy and in promoting material progress. The obvious and most commonly discussed effect of overdevelopment of oil fields is illustrated by the allegation that already the excessive development of the East Texas field has cost upward of $162,000,000;2 in other words, the drilling of 12,500 wells more than the number estimated as the requirement for economical recovery of the reserve has unnecessarily raised the total cost of development that amount. Many other illustrations of so-called excessive development of oil pools could be presented. Some of them, like Cushing, Powell and Long Beach, might be drawn from the era antedating widespread discussion in the trade of such matters as optimum well spacing, reservoir energy, the conservation rate of depletion of reserves, etc. Numerous other cases can he found in the records of the current era, which began with the introduction of rationalized restriction of production. Besides East Texas, there may be mentioned Oklahoma City, Centralia and. more recently, the town-lot development of Bloomingdale, Michigan.

Jan 1, 1940

By E. Werchowsky

FOR over four years, since the revolution of 1917, Russia has been cut off from the Western world. Political and general economical reforms have attracted the attention of the public and business world, but mining men have had no information as to the situation in their branch of industry, as various articles which have appeared in the European and American press gave little information as to actual conditions in our country. When the Soviet system of government was estab-lished and private ownership abolished, it affected the FIG. 1.-ORGANIZATION OF THE COUNCIL OF MINES. mining industry very little at first. The power of the Soviets did not affect the Ural provinces nor Ukraine or Asiatic Russia (Siberia, Turkestan, etc.) during 1918 and 1919, and, as is well known, the mineral wealth of the republic lies within those boundaries. In the Ural Mountains are copper, gold, and platinum; in Siberia, silver, lead, zinc, and gold, and the coal deposits in Koushetz district; in Ukraine, there are the coal fields of Donetz and the iron mines of Krivvy Rog, and silver, lead, zinc, copper, oil, etc. in the Cauca-sus. The mineral resources of Central Russia are the coal fields of Moscow (low-grade and brown coal), turf deposits, iron mines in Tula and Kalonga provinces, and quarries of granite and other building materials.

Jan 8, 1922

By C. L. Dake

Chemistry of Iron Solution IRON is much more soluble in the ferrous than in the ferric form. Where, as in the case of the ferrous silicates and the sulphides, the iron is already in the ferrous form, it may go at once into solution and be removed, upon the breaking down of the parent rock. If in the ferric form, it must first be reduced; usually by the decay of organic matter, the demand of the decaying carbonaceous matter for oxygen being so great that the latter is abstracted from the ferric compounds and the iron is thereby reduced and rendered' soluble. The iron may go into solution as the sulphate, or in the presence of excess CO2 as ferrous carbonate. It is probably soluble as salts of the organic acids.1 Recent work indicates that these are important in the formation of bog ores.2 There is considerable variety of opinion concerning the behavior of these organic compounds.3 The secretions about the roots of plants and trees also cause the solution and removal of iron and a consequent bleaching of the soil.4 While the matter is not yet well understood, we can probably say definitely that the so-called organic acids are a group of colloids which possess slightly acid properties, and the salts of which are partly soluble

Jan 7, 1915

By Jouko O. Kallioinen

The control of zinc flotation at Outokumpu Oy's Pyhasalmi and Vihanti mines is described. At Pyhäsalmi the zinc flotation circuit is partially open. Zinc and other metal assays of pulp flows are measured and direct assay control of concentrates in various flotation steps is adopted. Assay control is carried out by adjusting flotation air and pulp levels. Optimization with copper sulphate ensures high Zn- recovery and minimum copper sulphate consumption. A froth depth monitor is used to measure froth quality. At Vihanti the zinc flotation takes place in closed circuit. The most important control loop is the Zn-assay control of rougher concentrate by adjusting flotation air. The quality of froth is measured indirectly and thus copper sulphate consumption is altered. The circulating load is controlled also by flotation air in the three cleaning steps. The comparison of the control strategies shows that a more sophisticated control is adopted at Pyhäsalmi because the selective flotation of this massive sulphide ore is considered to be difficult. The control strategy includes numerous tests performed by the computer and control algorithms developed for the case. The control targets of the two zinc flotations described are also different: At Pyhäsalmi Zn-assay control of final concentrate including copper sulphate optimizing, at Vihanti the control of circulating load and Zn-assay of rougher concentrate.

Jan 1, 1984

By Henry S. Poole

This field is geologically of much interest. It is small, hut with some seams of unusual thickness, the main one being as much as thirty-eight feet thick. The quality of the seams, as also of the associated beds of shale and sandstone, in several instances changes to a remarkable degree within short, distances. The strata dip at inclinations that carry the coal to depths of 3000 feet or more; heavy faults cut up the district, and the New Glasgow conglomerate, of disputed age, separates it from the Upper Carboniferous measures, in which no seams of workable thickness are known. This coal-field offers to the geologist much ground for study and peculation. The commercial value of the field is affected by its restricted area, the varied quality of its coal, and its advantageous position in the mainland, with railway connection and home markets, offset by the physical difficulties which make the cost of production high. It has been so long a habit with us to speak of our resources of coal as boundless, that any adverse comments, or insinuations that avoidable loss in working is a national loss, hare hitherto fallen on idle ears. While it is not my purpose to underrate the riches we do possess, yet I deem that no good end is served by echoing exaggerated estimates which encourage a national indifference to wasteful

Jan 1, 1886

By George W. Lower, William A. Hockings, Donald A. Kaczynski

The rate of dissolution of polycrystalline metallic copper in aqueous cupric ammonium nitrate solutions in the non-film-forming region was investigated by the rotating disc method. The investigation was performed in solution concentration ranges applicable to hydrometallurgical processes. This investigation was an extension of a study on the cupric ammonium carbonate system previously reported by Smith, Lower and Hockings, in which the following kinetic model was proposed: (1) Diffusion of cupric ammine ions to the copper surface; (2) Forward reaction - first order reaction of cupric ammine ions with metallic copper; (3) Reverse reaction - disproportionation of cuprous ammine ions to metallic copper and cupric ammine ions ; and (4) Diffusion of cuprous ammine ions from the copper surface. The nitrate system was selected for this study because it simplified the determination of the ionic composition of the solutions. The variables studied were stirring speed and cupric, ammonia, and nitrate concentrations. The dissolution rate increased linearly with at low values of but exhibited increasingly negative deviations from linearity at higher values of m. The rate also increased with increasing cupric concentration but decreased with increasing ammonia and nitrate concentration. Good agreement was obtained between the experimental rate data and the proposed model. Further verification of the model was indicated by the close agreement of the diffusion coefficient calculated from the data and comparable literature values.

Jan 1, 1974

By P. Somasundaran, K. P. Ananthapadmanabhan

A knowledge of the role of effects and interactions of chemical species is important in developing an understanding of the behavior of mixed minerals and natural ores in beneficiation processes such as flotation and flocculation. In this study the role of such species was examined for the calcite-apatite system by conducting flotation of each mineral in various supernatants prepared by mixing with water. Supernatants of apatite and even that of calcite depressed the flotation of calcite markedly in the pH range of 5 to 13. Addition of Ca(NO3)2, K2C03, and K3P04 also produced definite effects under various pH conditions. Apatite flotation was also affected by the mineral supernatants and by carbonate and phosphate solutions. The results are analyzed in terms of the surfactant's solubility properties and the mineral's electrochemical and dissolution properties. While depression of calcite flotation by the dissolved species is found to be governed by depletion of oleate by bulk precipitation, the depression of apatite flotation is caused by the carbonate and phosphate species in the system. Turbidity measurements and a thermodynamic analysis of possible interactions in the system support these considerations. The effect of the supernatant of minerals on their own flotation suggests the important role of kinetics of various surface interactions in comparison to that of mineral dissolution.

Jan 1, 1985

By Teh-Yu Kao, Don J. Wood

With the increasing industrial use of the method of transporting solids by fluids through pipes, a better understanding of the basic mechanics of a solid-liquid pipe flow system is essential. In this study the phenomenon of incipient motion of solid particles resting in a sediment bed on the bottom of a pipe is investigated. Since a system would fail to operate at the designed solid-liquid flow condition if it was not capable of operating through the transient initial flow phase, information concerning the starting transient is of great interest. An objective definition of incipient particle motion, derived from energy considerations, is first proposed. Using this the critical state is defined to describe the flow condition during which a solid particle can at least temporarily escape the sediment bed and move in the liquid. Postulated also in this study is that the condition of incipient motion can be reasonably well predicted by a consideration of particle equilibrium in a direction normal to the pipe axis. The incipient condition is considered to occur at the instant the force between the bed and the particle, normal to the pipe axis, is zero. Experimental measurements of incipient conditions are obtained for water flowing through a horizontal pipe with sand sediment beds of different thickness. These are compared to predicted values with good agreement.

Jan 1, 1975

By R. G. Coyle

This paper describes a model of operating policies in an underground metal mine. The purpose of the model is partly that the problem of controlling a mining operation in the face of shocks from its economic environment is interesting in its own right, and also as an input to a larger research project on policy-making in mining companies. The model includes, mining, development and milling sectors together with cash flow and finances. In particular, it shows how the policies used to control the various sectors in the face of environmental shocks from metal prices and changing state of the system are connected by feedback loops. The use of feedback theory differentiates the model from 'ordinary' simulation and assists in the design of 'robust' policies which always achieve effective control. This model is the first stage of a major project and approximations have been made, simply to get the model going. The purpose of this paper is to show the kind of output this type of model produces, to lay our explicitly what is in the model and above all, to invite contributions from mining people on what the model should show and what should be put into it. We claim no virtues for this model. It is just a research tool so that later models will be more worthwhile and useable in practice.

Jan 1, 1977

By John Gill

THE purpose of this paper is to invite attention away from the obvious, direct monetary costs of oil-field overdevelopment (as dis-tinguished from "social costs") to a consideration of the role played by the exercise of freedom to create even allegedly excessive1 plant facilities in contributing to the maintenance of equilibrium in the whole economy and in promoting material progress. The obvious and most commonly discussed effect of overdevelop-ment of oil fields is illustrated by the allegation that already the excessive development of the East Texas field has cost upward of $162,000,000;2 in other words, the drilling of 12,500 wells more than the number esti-mated as the requirement for economical recovery of the reserve has unnecessarily raised the total cost of development that amount. Many other illustrations of so-called excessive development of oil pools could be presented. Some of them, like Cushing, Powell and Long Beach, might be drawn from the era antedating widespread discussion in the trade of such matters as optimum well spacing, reservoir energy, the conservation rate of depletion of reserves, etc. Numerous other cases can be found in the records of the current era, which began with the introduction of rationalized restriction of production. Besides East Texas, there may be mentioned Oklahoma City, Centralia and, more recently, the town-lot development of Bloomingdale, Michigan.

Jan 1, 1939

Diffusion in Solid Metals. BY ROBERT F MEHL (Institute of Metals Division Lecture Tech Pub 726 in Metals Tech, Aug , also Trans, vol 122 22,500 words ) Diffusion in solid metals constitutes one of the important fundamental phenomena in metallurgical behavior Apart from its obvious importance in processes such as chromizing, carburizing, nitriding and calorizing, it plays an important part in the processes of homogenization, age-hardening, and transformations in steel, its scientific importance is no less great Diffusion may occur within a grain, along a grain boundary, or upon a surface, though the exact and even the relative values of these separate processes are known for only a very few cases The requirement of solid solution formation presents the possibility of identifying solid solution phases by a study of diffusion layers Some distortion accompanies diffusion, leading to little¬ understood grain-size changes Distortion assists diffusion though usually it dis¬appears before diffusion has become extensive In a binary system the rate of diffusion is the more rapid in the lower melting metal Many of the published data are too qualitative to permit sound scientific conclusions Age-hardening data may be treated as diffusion data and rates of reaction in steel could profitably be studied from this point of view Studies on diffusion are of great importance to the develop-

Jan 1, 1937

By M. J. Duggin

Evidence is produced below to show that the carbide "Mn,C," reported by Kw,and ersson' is really a mixture of two carbides. One is an Fe-Mn carbide which is probably isomorphous with hexagonal Mn15C4, reported by Bouchand and Pruchart.' The othev is a tetragonul Fe-Mn carbide with cell dzmensions close to those reported previously by the author3 for an Fe0.1Mno. carbide. IN a recent investigation several Fe-Mn carbide specimens, each weighing about 5 g, were prepared in a manner previously reported.3 Debye-Scherrer X-ray photographs were taken of at least two samples from different parts of each specimen using a 114.6-mm-diam camera. The exposure time was 2 hr using filtered chromium radiation, a tube voltage of 35 kv and a tube current of 10 ma. In the case of one specimen, which contained nominal weight percentages of iron, manganese, and carbon of 9.40, 84. 6,, and 6.0, respectively, duplicate chemical analyses indicated f1.2 and 5.5 wt pct C to be present in the two samples taken of the specimen: no graphitic carbon was detected. One powder-diffraction pattern of this specimen indicated the presence of the tetragons: carbide reported earlier,3 (a = 6.772A, c = 9.427A), plus cementite (O), plus an unknown structure. The second powder-

Jan 1, 1970

By C. W. Mallett

The distribution and properties of interseam and overburden rocks in coal mines is largely controlled by conditions at the time of their original deposition. Within the developed areas of the Bowen Basin, depositional environments range from fluvial through upper and lower detaic, to marginal marine and intertidal facies. Each environment has a characteristic association of lithologies with specific range of properties, and each lithology has a characteristic geometry. Fragmentation problems are associated with ancient sand channel systems, where the difficulties encountered depend on the dimension and shape of channels, their continuity, orientation to mining face and associated sediment bodies formed as levees or interdistributary muds. Stability problems in spoil, pit floor and highwalls are usually associated with mudstones which contain swelling clays derived from the original Permian volcanic source. This clay problem is aggravated by deep Tertiary weathering. Case studies are presented of detailed analyses and prediction of geomechanical properties on a mine site scale. These are used in investigating or forecasting fragmentation and stability hazards. The studies incorporate detailed field mapping, bore log data and computer data processing. They allow the development of detailed depositional models for specific interseam intervals within mines. As areas of depositional environment are identified they allow the construction of maps of similar mining conditions and the determination of the most suitable mining techniques.

Jan 1, 1983

By Frederick T. Fischer

The New Jersey Zinc Company began a program of exploration in Middle Tennessee in 1964. The target horizon of the exploration project has been the Knox Dolomite which is a low-yield aquifer over nearly the entire Central Basin of Tennessee (1). With the exception of a few hundred acres in the Wells Creek and Flynn Creek disturbances (astroblemes?), the Knox Dolomite in Middle Tennessee is known only in subsurface. In January of 1969, New Jersey Zinc announced the discovery of a major zinc deposit near Elmwood, southeast of Carthage. This is on the northeastern flank of the Nashville Dome where the nearly flat-lying beds have an average eastward slope of about 50 feet per mile. The anticipated development of a mining situation has emphasized the significance of hydrologic relationships in the region as a whole and especially in the Elmwood area. These relationships affect several areas of concern which ma be generally grouped into two broad classes; i. e. , (1) Problems of a Public Nature - involving the prevention of the contamination of potable aquifers, the prevention of the contamination of surface waters, the prevention of the capture of presently utilized water, etc.; and (2) Problems of Mining Economics - involving pumping capacity and costs, the possible need for equipment of special composition, underground environmental conditions, etc. Exploration drilling in Middle Tennessee has contributed additional information about the Knox aquifer and

Jan 1, 1970

By J. P. Norris, W. T. Pettijohn

The Mufulira Copper Mine, Ltd., is in Northern Rhodesia, ten miles from the Belgian Congo border, and is one of the group of four operating mines comprising the Northern Rhodesian Copperbelt. The ore deposits at Mufulira are on the limb of a large syncline striking NW.-SE. and dipping NE. at about 45 deg towards the Congo border. The host rocks are well-consolidated, highly-silicified, felspathic quarzites of the lower part of the pre-Cambrian Séries des Mines of the Katanga. The ore rocks are underlain, unconformably, by the older "Muva Series," in this case hard, green, metamorphosed quarzites. There are three superimposed orebodies, the first, or upper, orebody averaging 40-ft true thickness with a strike length of about 5000 ft, the second, or middle, orebody of about 50-ft true thickness with a strike length of about 6000 ft, and the third or lower orebody of around 60-ft true thickness with a strike length of 8000 ft. The orebodies are separated by varying widths of waste, or very low-grade ore, from a few feet up to 50 ft. The middle and lower orebodies are so close together for a strike length of 3000 ft that they are mined as one orebody. In all, the mineralized zone is about 200 ft in true thickness.

Jan 6, 1950

By J. D. Corbett

Mining geophysics in 1967 continued to expand with greater application in the exploration and development of mineral deposits. Moreover, geophysical activity increased without the particular emphasis of a Pine Point or Timmins discovery to spur interest. This trend is expected to continue through 1968 as geophysics more and more becomes an integral part of a mineral exploration program. This past year saw the "little black box" of the old-fashioned "doodlebugger" pushed further into the background, replaced by increasingly sensitive equipment of sophisticated design. The trend also is away from the one man geophysical operation wherein the same individual is responsible for the development, design and operation of the field gear, the planning and execution of a survey and analyzing and interpreting the data. In today's technology a staff of specialists, electronics engineers, mathematicians, physicists-to name but a few- are required to back up the exploration geophysicist in the development of new methods and techniques, in the reduction of the voluminous amount of field data and in the interpretation of the anomalies which can be enhanced by various high-speed computer techniques. Obviously a full back-up staff of these varied abilities is impractical to most exploration companies. However, the equivalent function is provided to the lone staff geophysicist by the many competent geophysical contractors and individual consultants.

Jan 2, 1968