Search Documents

By C. H. Mathewson, J. A. Collins

The process of plastic extension of face-centered cubic single crystalline rods is so well understood, since the notable studies of Taylor and Elam,1 that the change in orientation of any crystal by slip and rotation may be predicted from the measured elongation. It is customary to assume a very homogeneous deformation, wherein gliding lamellar arc free to rotate so that their slip direction continually approaches the axis of the rod, until a second slip system comes into operation; whereupon conjugate slip proceeds quantitatively to an end adjustment with the [121] direction in the axis of the rod. This process has been checked in malty face.-centered cubie materialsand and readily permits the preparation of specimens that have been subjtvted to various determinable amounts of shearing action. It is elearly of interest to study in such measurably strained speeimens the, development of a recrystallized structure on annealing and if possilble detect the source of nuclei from which the new crystals grow. Strain-:~nneali~ig experiments of this charactcr have been performed by others but not in detail sufficient to permit a study, for example, of the number of recrystallized grains vs. the amount of shear. In the experiments now reported, this was done with a wide variety of orientations covering nearly the entire range of slip on a single system and corresponding to amounts of shear (ratio of shearing distance to distance between lamellae at the conclusion of a test of from 0.08 to 0.57. A particular point wa-made of determining the crystallite rotation, or small angular range. assumed by the octahedral slip plane after these various amounts of shear. The, mechanism of reerystallization and the magnitude and effeet of recovery on the recrystallization process was investigated.

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By Eugene Coste

ALTHOUGH some of the observers who first paid especial attention to the occurrences of oil and gas in the strata (such as Hunt in 1859, Andrews in 1861, Winchell in 1865, Mendelejeff in 1876, Höfer in 1876, Minshall in 1881, and I. C. White in 1883) seem to have been impressed with the fact that oil and gas deposits were connected with the disturbances in the rocks caused by their upheaval,1 yet, with the exception of Mendelejeff, and possibly Andrews, these observers do not appear to have understood what is really the one essential factor in the occurrence of oil and gas in the strata: viz., the faulting, uplifting, fracturing, fissuring, and jointing always accompanying even slight rock disturbances, and in certain districts (petroliferous provinces)2 allowing solfataric hydrocarbon emanations to force their way up from the interior and to reach and impregnate the porous portions of sediments subjected to the disturbances. Instead of this simple explanation to account for the observed connection between petroleum deposits and rock disturbances, most of the observers mentioned above, and many others who have followed them on the name lines since, have entirely reversed the problem. To them, instead of the dissemination of gases from fissures into the sediments, it presented the accumulation and concentration, according to anticlinal or other geologic structures, of oil and gas originally present throughout the whole mass of the strata where they were produced by the decomposition or distillation of organic remains. Whether this important problem involves accumulation from sources within the oil-bearing strata themselves, or infiltration and dissemination from outside sources, may be easily determined if all preconceived ideas are put aside and the established facts only are considered.

Jan 9, 1914

By R. B. Campbell

One of the three power plants that will be in the Curecanti Unit of the Bureau of Reclamation's Colorado River Storage Project is the power plant at Morrow Point Dam. Presently under construction, the Morrow Point Power Plant is between Gunnison and Montrose on the Gunnison River in west-central Colorado. (Fig. 1). Morrow Point Dam will be a thin, double-curvature, concrete-arch dam, 465 ft high and will impound 120,000 acre-ft of water. Two 60,000-kw hydroelectric generators will be housed in an underground power plant in the left abutment just down- stream from the dam. The power-plant chamber will be an unlined opening 205.5 ft long, 57 ft wide and 65 to 134 ft high. The arch-type roof with a rise-to-span ratio of 1 to 4 will be supported with rock bolts and chain link fence. A description and discussion of the design considerations for the power-plant opening and rock bolt design are given by William H. Wolf, Gilbert L. Brown, and Ernest D. Morgan in "Morrow Point Under- ground Powerplant," ASCE Power Division Specialty Conference, Denver Colorado, August 18-20, 1965. The Morrow Point site is in a moderately active region of mild earth- quakes, as evidenced by recent earthquakes in 1960 and 1962. Therefore, the Bureau of Reclamation undertook an investigation of the effects on the underground power-plant chamber when subjected to an earthquake. The art of earthquake engineering has been directed primarily at developing methods of analyzing the nature of ground surface motions and designing surface structures to resist damage from vibrations impressed on the structure by the ground motions. The mechanism of straining an underground cavity by an earthquake

Jan 1, 1968

By C. G. McLachlan

THIS paper outlines a series of tests carried out during the first six months of 1927, in the laboratory and mill of the Moctezuma Copper Co. The object of the tests was to determine whether the soluble salts present in the mill circuit water were having a detrimental effect on the recovery made by flotation. To accomplish this object a series of water analyses were made, followed by flotation experiments in which definite quantities of the salts found were added as addition agents. Before proceeding to describe the results obtained in the course of the investigation, reference will be made to five articles that have appeared during the last two years in which the action of such salts is discussed. Two of these are by A. T. Tye1,2 and describe flotation practice at Cananea and the way in which water high in ferrous and ferric salts is conditioned for differential flotation. Two, one by A. C. Munro and H. A. Pearse3 and the other by H. A. Pearse,4 outline Britannia milling methods, and the advantages that have been derived from ore washing; while in the fifth, A. W. Hahn5 summarizes the results of laboratory experiments in which ferrous, ferric and aluminum sulfates have been added in varying amounts. The mill of the Moctezuma Copper Co. has a daily capacity of 3000 tons, and is situated about 75 miles south of Douglas, Arizona, on the Rio de Nacozari, in the Mexican state of Sonora. The ore treated is mined from the company's mine at Pilares, about 5 miles southeast of the Concentrator. This ore contains about 2.5 per. cent. copper -- present almost entirely as chalcopyrite-and 10 per cent. iron, of which

Jan 1, 1928

By H. A. Buehler

The Ozark region occupies a large part of the southern half of Missouri, the northern portion of Arkansas and comparatively smalll areas in northeast Oklahoma, southwest Kansas, and southern Illinois. It is a roughly elliptical plateau which has been deeply dissected by stream erosion, and which slopes imperceptibly into the prairie regions to the north, east, and west, but which terminates rather abruptly along the Arkansas River on the south and Tertiary lowland to the southeast. The Boston Mountains extending for a distance of some 200 miles (321 km.) along the Arkansas River rise to an elevation of 2000 ft. (609 m.), forming the most prominent topographic feature of the region. The so-called St. Frangois Mountains in St. Frangois, Madison, and adjoining counties in southeast Missouri, form a prominent but more restricted topographic feature, the highest point rising to an elevation of 1800 ft. (548 m.). The remainder of the region is largely a plateau area varying from 800 to 1500 ft. (243 to 457 m.) in elevation. Stratigraphy The region is underlain chiefly by sedimentary formations, which outcrop in roughly concentric bands around a comparatively restricted area of igneous rocks in the St. Frangois Mountain district. Although located geographically near the eastern edge of the Osarks, the St. Frangois Mountains have apparently suffered the greatest orogenic movement and the lowest formations of the succession are exposed in their immediate vicinity. The various sedimentary formations of the region do not show any considerable metamorphism and have suffered little change since consolidation. With the exception of a few basic intrusions in Ste. Gene-vievg County and a pegmatite dike in Camden County, Missouri, there is no evidence of igneous action, since the first sedimentary beds were deposited.

Jan 1, 1918

UP TO and including 1931, the twelve mines that were treated in THE PORPHYRY COPPERS had produced 17.4 billion pounds of copper worth $2,820,000,000. With a little help from six others (three of them did not start output until 1954) that record had been increased at the end of 1955 to 60.5 billion pounds worth $10,440,000,000. Today, ten billion dollars is not as impressive as it once was; but it still represents a lot of value. It must be remembered that this is newly-created wealth, produced entirely from material considered worthless when the Porphyry era started about fifty years ago. At that time "rock" that contained less than forty pounds of copper per ton was regarded by competent mining engineers as value- less. It was not "ore" in the economic sense. Today, ore is being successfully exploited that contains less than twelve pounds of copper per ton. Also, in Peru, a typical Porphyry operation is being launched by a partnership of four United States mining companies that will involve an initial capital investment of $200,000,000 for mine development, plant construction, and the provision of related facilities. Of this project more will be said at the end of the chapter. The point I want to make now is twofold: (1) that phenomenal progress has been made in Porphyry engineering and technology; and (2) that exploitation of an important Porphyry copper deposit has become an industrial enterprise of truly great magnitude. Much had been accomplished by 1931; but that progress has been dwarfed by the achievements of the past 25 years- a fact that, in the nature of things, is as it should be.

Jan 1, 1957

By Norberto Dominguez

In the year 1820 a commission, assisted by Sr. C. Fernando de Ainada, was appointed by Sr. Jose Ramon Mila de la Roca to report on the condition of the mining region of Parral, in the State of Chihuahua, Mexico, where in recent years the mines of Batopilas have reached an important development under American management. The object of the inquiry was to provide Sr. De la Roca with facts to support a project for reopening mines that two centuries before had produced a large amount of silver. Although this plan failed, many facts of interest in the history of the mines were presented.. Much of the report dealt with questions that had only local application or were restricted to the conditions of labor and equipment in the opening of the nineteenth century. The historical part is presented in the following paragraphs: Abstract of the Report. Notwithstanding the difficulty of forming a just estimate of the system of mines in this mineral group in the valley of Senor Sail Jose del Parral without an examination of each of them, that which we shall say in a general way will suffice to convey an idea of their value and of the urgent necessity of reopening them. If this is undertaken, we believe the results will be of the highest consequence to the Republic, as well as to this immediate locality. The group of the Villa del Parral covers the mineral territory in which the village of that name was located. Its moantains contain large metallic veins, from which, as from the trunk of a tree, depend others much more slender, locally called ,fibras, crossing and interlacing each other in many directions. The first and oldest of these very rich deposits of gold

Jan 1, 1902

By M. Friedman

Applications of rock mechanics to the design of engineering structures in rock involve the assumption that the stresses are due entirely to the present applied loads. For instance, it is assumed that the vertical normal stress in undisturbed rock free of topographic effects is equal to the weight per unit area of the overburden. In fact, vertical dilatational strains associated with stresses of more than 100 times the present overburden pressure have been measured by strain-relief methods on outcrops. 1,2 The notion of residual strain (stress) or latent stress3 seems unassailable; and indeed this has long been recognized by metallurgists. It is difficult, however, to assess the residual component of the in-situ state of elastic strain with conventional strain relief methods employed in mines or down boreholes. That is, in principle, the in-situ state results from the superposition of present applied loads (natural or man- induced) and potentially recoverable elastic strains (stresses) that exist in a given volume of material even though there are no external forces across the boundaries of the body (Voight,4 and Fig, 1). Accordingly, only in unloaded blocks can the true residual strains be measured by strain relief methods. Using X-rays, the elastic strains locked within the quartz grains or crystals of a rock can be measured. These strains are known to persist even when the rock is reduced to small chips but to vanish when the rock is disaggregated and the grains are powdered. Although we have just begun to investigate the mechanisms by which the strains are stored (see Preliminary Results), we believe that "pressure solution'' at grain boundaries, secondary cementation under load, permanent ("plastic") deformation, and temperature changes are possible processes. In any event, in our study of naturally deformed rocks, it is significant that we are work-

Jan 1, 1972

By Henry E. Colton

NeaR the town of Christiansburg, Va., occurs a singular feature in topographical as well as geological structure, which may be said to have an important bearing on a large area to the southwest. The great water-shed ridge, which divides the waters flowing into the St. Lawrence from those flowing into the Atlantic ocean, coming southwestward, forms all of what was the boundary of Maine as agreed upon by the treaty of 1783, and a part of the present boundary, all of the northern New Hampshire boundary, and entering Vermont, continues south of Lake George. Passing irregularly through New York, it enters Pennsylvania, and there bifurcating, sends one prong to the west as a divide between the waters of the lakes and the Ohio, while the other becomes the steady, regular ridge which gave it the name of Alleghany, and thus passes on southwestward through Virginia. At no point has it ever been the geological divide. Its course, commencing in the Archean rocks, has passed through nearly every series of formation, and comes into Virginia in the Carboniferous strata. The geological divide—the line between the fossiliferous and the non-fossiliferous rocks—lies, in Canada, to the west of it, but from New York south into Virginia is far to the east. Reference to Dr. Hitchcock'k map will show this. But at the locality noted these positions are changed; the water-divide becomes the eastern chain, and the geological divide is the western, returning, it may be said, to the positions occupied in the region where they originated. These relations are shown on the large map accompanying the present paper. For several miles, the track of the Norfolk and Western Railroad

Jan 1, 1888

By C. H. Herty

The elimination of metalloids in the open-hearth process depends on oxidation of the metal by diffusion of FeO from the slag (or absorption of FeO by the metal), with subsequent reaction between dissolved iron oxide and the metalloids carbon, manganese, phosphoms, and silicon. During an investigation on deoxidation with silicon, data on rate of oxidation of the metal were obtained, and these combined with certain other information, are presented here in an attempt to show the fundamental principles governing the diffusion of FeO from slag to metal. Inasmuch as the aim of the investigation was not a study of diffusion, certain data are lacking and it has been necessary to make assumptions on metal viscosity and effect of temperature on diffusion. These factors are known to exert a considerable effect on diffusional processes. Overoxidation, or supersaturation of the metal with iron oxide, is not taken up in this paper. Overoxidation has little effect on diffusion except under a few special conditions, and the discussion has therefore been limited to diffusional processes. Though the results given in this paper should be regarded as preliminary, certain of the conclusions drawn are definitely applicable to any steelmaking process. Previous Study of Absorption An extensive study of absorption has been made by the Department of Chemical Engineering, Massachusetts Institute of Technology. The results are of such direct interest in the problem of slag-metal reactions that it is feIt worth while to summarize them here. The following quotations are from Lewis and hitmman.1 The reader need simply substitute "slag and metal" for "gas and liquid," with proper modifications to take into account the variations in physical properties of

Jan 1, 1929

By B. W. Gonser

SOFT solders are used principally in the automotive, can-making, building construction and electrical industries, but their field of usefulness extends well beyond these principal users to a vast list of miscellaneous applications where metal joints are required. The most common soft solders and the only ones considered in this discussion are those com-posed of lead and tin, with or without various relatively small percentages of impurities or additions. A small amount of antimony is often pur-posely added. As an indication of the importance of these lead-tin solders, 8620 long tons were consumed in 1934 in the U.S., and during most of 1935 from 900 to 1000 long tons were used each month. A great many factors influence the properties of joints made with soft solders. Fluxes and the fluxing procedure used to prepare the surfaces to be joined in order to give a true metal-to-metal contact are among the most important of these factors. The temperatures used, cleanliness of the work and general soldering technique have their effect, but when results are unsatisfactory they are usually attributed to the metallic solder itself and the raw materials from which it is made. Some-times criticism of the solder is justified. The wrong composition may be chosen for a given job, impurities may be present that ruin certain desired qualities, or uniformity may be lacking. A solder may even be looked upon with suspicion because of its ancestry, regardless of its true composition and behavior. To clarify the effect of slight differences in composition as found in commercially refined solders, a comparison of properties of solders grouped according to their origin has been undertaken. This investigation seeks to give practical information on the proper-ties of tin-lead solders produced from virgin metals, from commercially

Jan 1, 1936

By P. J. Shenon, J. C. Reed

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By Charles Barrett

PLASTIC flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following funda-mental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the lattice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals -"grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by vari-ous investigators for more than 25 years, ? yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of mate-rial that was used in the earlier compression experiments1-hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By E. E. White

In August, 1911, I read a paper before the Lake Superior Mining Institute1 on surveying and sampling diamond-drill holes. The present paper gives a more thorough descriptiou of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling' and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drillholes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-hole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a

Jan 1, 1913

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By A. J. Lynch, E. V. Manlapig, J. S. Hall, G. C. Thorne

Modelling of industrial sulphide flotation based on data collected in several flotation plants is discussed. A mechanistic approach is used in which it is recognised that flotation is a two stage pro- cess with concentration occurring both in the pulp and in the froth. The important features of the model, which is a kinetic model, are – 1. for each particle species there is a range of flotation rates which corresponds to the range of particle sizes, 2. the flotation rates of the liberated gangue particles which have no hydrophobic properties are dependent on the flotation rate of water and are controlled by variables such as the air and frother addition rates, and the pulp level, 3. as an approximation the valuable sulphide particles may be regarded as being present in two groups with high and low flotation rate constants, 4. increase in the addition rate of collector tends to increase the proportion of sulphide particles which are in the high flotation rate constant group. The actual flotation rate of each group of particles is a combination of an "inherent" flotation rate and a flotation rate which is dependent on the flotation rate of water, 5. at particular air and frother addition rates and pulp levels there is a physical limit to the rate at which particles can be transported into the concentrate and this is recognised in the model. The model has been used to study the steady state and dynamic properties of flotation circuits in operating plants. The assessment of the behaviour of composite particles is difficult because of the problem of quantitatively describing the surfaces of mineral particles. A method which is being developed to measure unpolished particles is described briefly.

Jan 1, 1976

By D. Coutsouradis, L. Habraken, P. Nicolaides

The TTT curves of 0.1 pct C, 13 pct Cr steels containing up to 12 pct Co have been determined in order to establish whether the effect of cobalt is similar to that observed m plain carbon steels. It is shown that cobalt increases the incubation time and decreases the transformation rate, though not in an uniform way. The bainitic transfornation is displaced to lower temperature and overlaps partially the martensitic zone. ThE effect of cobalt on the transformation of a plain carbon austenite has been studied by many investi-gators.'-3 It was shown that cobalt displaces the TTT curves to shorter times and diminishes the harden-ability. The interpretations given for this effect of cobalt are conflicting. According to E. Houdremont,4 cobalt increases the transformation rate of austenite because it increases the diffusion of carbon as shown in the experiments of E. Houdremont and H.Schrader,' R.Smoluchowski,5 and M. Blanter.6 On the other hand, M. Hawites and R. Mehl3 deny on the basis of their own experiments any effect of cobalt on the diffusion of carbon and they assume that an explanation should be found in an eventual effect of cobalt on the mechanism of nucleation and growth of pearlite. W. C. Hagel, G. M. Pound, and R. F. Mehl7 have shown by calorimetric measurements that cobalt increases the free energy of the austenite-pearlite transformation in an eutectoid steel and this result explains qualitatively the observed effect of cobalt on the rate of nucleation and growth of pearlite. The purpose of this research was to see by determination of TTT curves, if this same effect exists in 13 pct Cr steels. EXPERIMENTAL PROCEDURES The preparation of the alloys was carried out in an

Jan 1, 1960

By R. M. Brick, Arthur Phillips, A. J. Smith

A previous publication1§ has described the effect of quenching stresses on the lattice parameter values of high-purity aluminum-copper alloys particularly with reference to the solution and precipitation of CuAl². A similar study has been made of the aluminum-rich aluminum-magnesium alloys. Attention has been directed in the present investigation to the magnitude of the quenching stresses as affected by the specimen size and shape, the number of solute atoms and the quenching rate. The effect of cooling stresses in causing plastic defomation or cracking has been considered in relation to the physical properties of the alloy On reheating alloys in the two-phase field, the time required for precipitation to occur has been observed in connection with the degrec of supersaturation, the rate of diffusion of the solute atoms as a function of the comparative atomic radii, degree of strain, temperature of reheating and grain size. A few qualitative comparisons on the relative effect of these factors have been drawn between the aluminum-copper alloys and the aluminum-magnesium alloys. Strain in Solid-solution Alloys A 10 per cent magnesium alloy ill the form of chill-cast bars was furnished by the Aluminum Company of America through the courtesy of L. W. Kempf. Additional alloys were prepared using alllminum (99.95 per cent Al) and high-grade magnesium. The alloys listed in Table 1 were melted in an Acheson graphite crucible under a flux of fused MgCl², CaC12, NaCI. Chill-cast rods were sealed under vacuum in Pyrex glass, homogenized several days at 450' C., air-cooled and machined to rods of from 1/8 to ¾-in. dia. Metal powders taken from these rods with a fine-toothed saw were again sealed under vacuum in

Jan 1, 1935

By Walter Harvey Weed

The Republic of Mexico is traversed by many mountain ranges, and presents a great diversity of climates, soils and geographical features, yet its grander geographic provinces are few and peculiarly well defined. The Gulf plain, the Cen tral plateau, the Sierra Madre, and the lowland or Tierra Cali ente of the western coast are the main features of the geogra phy of the Republic, and in the northern half these provinces are particularly well defined. The Sierra Madre separates the Republic into eastern and western parts, and from the City of Mexico north to the Texas line presents an almost impassable barrier to east and west travel. On the north, the first wagon road pass from east to west is at El Paso del Norte, the site of the Texan city of El Paso. Southward for many hundreds of miles the Sierra Madre, traversed by well-worn trails, over which all travel from the west coast to the interior must pass, is a stupendous barrier to social and commercial intercourse. The Sierra Madre is commonly described as a range or con geries of mountain ranges. In fact, it is, in Chihuahua at least, a great plateau, fringed by mountains on the east, trenched by deep canons in its center, and bordered by a wild and rugged complex of mountains carved out of the plateau on the west. Professional duties took me across this region from Parral westward to the Gulf of California via Guadalupe y Calvo. As it includes some of the great ore-deposits of Mexico, and its geological features have never, so far as I am aware, been described, I have prepared a diagrammatic section made from my observations on a horseback trip across the Sierra, and added such notes as seem to be of general interest.

Jan 1, 1902