Search Documents

By A. E. Bellis

THERE is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat-treatment, structure, and physical properties. In order to promote discussion, which it is hoped may lead to the discovery of the source of 'some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat-treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.1 The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08. per cent. The minimum physical requirements are: Tensile strength,- 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirement's gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in- the best heats of open-hearth steel, so that' faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at, a proper temperature clown to the form of tapered barrel blanks or by heat-treating bars that have been upset to enlarge the breech section. The transformation temperature of this steel, on heating, is around 1350° F. (732° C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different

Jan 7, 1919

By AIME AIME

IN ACCORDANCE with the provisions of the Rules of Procedure of the American Engineering Standards Committee, the American Society for Testing, Mate-. on Feb. 15, 1921, submitted for approval by the A. E. S. Committee certain Standard Specifications for Copper, all of which were adopted or in process prior to Jan. 1, 1920, and sent with the standards the following histories of development and statements of use. FOR SOFT OR ANNEALED COPPER WIRE (B3-15) These specifications were originaly adopted by. the American Society for Testing Materials in 1912. They were prepared by a committee of the Society designated as Committee B-1 on Copper Wire. The committee consisted of eleven members; representatives of five manufacturers of -copper wire, of four manufacturers of electrical apparatus, and of two firms of consulting and contracting engineers. The members of the committee were designated by the officials of the companies to act as their representatives in the committee.

Jan 1, 1921

By Gregory L. Gullord

In September, 1975, production was begun at the new milling facility of ASARCO Incorporated, the Young Mill. The mill is located adjacent to the Young Mine 35 km (22 miles) east of Knoxville, Tennessee. The Young Mill replaced the obsolete Mascot Mill which had been operating since 1913. The basic flow sheet of Mascot was retained for the construction of the Young Mill, with a 20% increase in capacity included in the design. The Young Mill is capable of processing 7710 - t/d (8500 stpd) of crude ore from three underground mines (Young, Immel and Coy) yielding 300 - t/d (330 stpd) of 63% zinc concentrate. The Young Mill is unique in that 92.5% of the ore milled is recovered as saleable products, including zinc concentrate, construction aggregate, sand and agricultural limestone. Processing at the Young Mill is divided into five basic stages: two-stage crushing, heavy media separation, grinding-flotation, concentrate filtering and drying, and limestone by-products recovery. The ore bodies are located in the Knox formation, which consists of primary dolomite, secondary dolomite and limestone with silicas in the form of chert and jasperoid. The zinc mineralization occurs as an exceptionally pure sphalerite. The ore contains an occasional abundance of pyrite and traces of fluorite and barite. TWO STAGE CRUSHING Ore enters the crushing section from two points. The Young Mine ore is hoisted into a 816 ton (900 st) bin which feeds a 1.52m (60 in) conveyor via a 1.52 m (60 in) vibrating feeder. The Immel ore is trucked 10 km (6 miles) by an independent contractor and weighed on automatic recording truck scales at the entrance to the property.

Jan 1, 1977

By C. W. Covington, H. C. Cook, J. F. Libsch

Sputtered aluminum thin films were prepared in each of two conventional bell-jar vacuum systems. One system utilized an inner "getter sputtering" enclosure; the second system was a standard diode sputterirlg arrangement. Consistent and repeatable film properties were obtained in both systems provided sufficient cleanup and presputter time was allowed. The various problems associated with aluminum sputtering are discussed, with pavticular attention to the vzinimization of film contamination by outgassing and oxidation. The growth and structure of the aluminum thin films were studied with the aid of electron wzicroscopy and related to deposition rate, substrate temperature, and film thickness. The resistivity of the films was correlated to film structure and surface roughness. Resistiuities as low as 3.5 microhm-cm (2.3 x bulk resistiuity) were measured for relatively thick films (20,000). THIS investigation was undertaken to explore the problems and film characteristics associated with the sputtering of aluminum. Earlier work reported on aluminum sputtering has stressed the contamination of both the cathode and film as well as abnormally low deposition rates.' Data on sputtering yields,3 however, indicate that aluminum sputtering could be practical. Recently, it was shown by Theuerer and Hauser3 that aluminum sputtering was feasible in a conventional oil-diffusion pumped vacuum system provided an inner "getter sputtering" enclosure was employed to minimize gaseous contamination. This technique employs the getter action of aluminum to produce extremely low reactive gas partial pressures in the deposition zone. Aluminum films have already found use in solid-state electronic devices such as transistors and integrated microcircuits. To the present time, most aluminum films have been prepared by evaporation due to the ease with which this metal can be evaporated. Controlled sputtering of aluminum offers a number of advantages over evaporation, however, such as 1) manufacturing compatibility with other metals which must be sputtered, 2) better control of process variables resulting in more repeatable and uniform films, 3) generally better adhesion resulting from higher-energy metal atoms, 4) built-in material supply for continuous operation, and 5) the ability to deposit alloys. The data presented in this paper are the result of two separate studies. One study utilized a small "getter sputtering" enclosure (System A) and was concerned with the structure and properties of thin aluminum films up to about 1600A thick. In this thickness range, study of the film structure was possible with transmission electron microscopy. The second study was conducted with a conventional diode sputtering apparatus (System B) and covered $ much wider range of film thickness up to about 34,000A. Emphasis was placed on developing techniques which would extend aluminum sputtering to an existing in-line continuous deposition process.4 I) EQUIPMENT AND PROCEDURE System A. Fig. 1 shows a schematic of the "getter sputtering" inner chamber used and Fig. 2 is a photograph of this chamber mounted on an 18-in. access ring of a standard liquid-nitrogen trapped bell-jar vacuum system. This chamber was designed after a similar system used by Theuerer and auser.3 The configuration allowed the glow to emanate in all directions from the cathode. Argon (99.99') was allowed to enter only at the top of the chamber such that most of the reactive gases entering with the argon were reacted with the aluminum vapor and deposited on the chilled walls of the chamber before reaching the deposition zone. Provision was also made as shown, Fig. 1, for heating and cooling the substrate from about 20" to 400°C. Two substrate materials were used: Corning 7059 glass (12 by 12 by 0.048 in.) and carbon films about

Jan 1, 1967

By Luther W. Bahney

(San Francisco Meeting, October, 1911.) LIME is the alkali that is almost universally added to the solutions in the cyanide process of gold- and silver-extraction for maintaining the so-called, protective" alkalinity. It is produced by the burning of limestone. The value of lime for this purpose depends upon the percentage of calcium oxide contained, which is determined by three factors : 1, purity of the limestone used; 2, degree of the burning-temperature and the period of burning; and 3, length of time of storage of burned material and the condition stored, and whether it has been damp or wet during the storage. These three factors render uncertain the quality of lime bought in the open market. In the United States, lime bought from reliable manufacturers, who thoroughly burn a pure limestone and deliver at once to the consumer from the kilns, may be of a fairly-high and uniform composition ; but in Mexico and Central America, where it is purchased from many small producers, who often start with a poor grade of limestone and burn it in small crude kilns with as little fuel as possible, the quality of the product is quite variable. In consideration of the foregoing, it is apparent at once that there is a great need for a rapid technical method for the valuation of the lime to be used in a cyanide-plant. The determination of calcium by the gravimetric method, with the necessity of determining also the proportion of carbon dioxide, silica, and iron, requires too much time, and is usually out of the question for an isolated plant unequipped with a skilled chemist and, the necessary apparatus. The calculating of all the calcium so found to calcium oxide, although sometimes done, is manifestly very inaccurate.

Nov 1, 1911

By Emil-Paul Lorenz

Considered as a whole, the mineral resources of the Turkish Republic (Anatolia) are in their untapped virgin state, and the little development shown is not the result of modern systematic geologic exploration but the continuation of the ancient open-pit mining methods of the Orient. When I came to Turkey in 1924, I found myself confronted by a formidable task because of the lack of preliminary geologic mapping. Today this condition has not essentially changed; less than one per cent of the country is covered by topographic mapping adequate for modern requirements. However, I was able to bring a semblance of order in a presentation of the mineral deposits of this country, by tracing the story of the mineral deposits that showed surface evidence of their existence. At present only the easily discovered mineral deposits of coal, copper, and lead-silver ores are being exploited. In the case of coal, of 3,000,000,000 metric tons available, only 100,000,000 have been mined. The same is also true for copper, lead-silver, and other ores, as shown in Table 1.

Jan 1, 1948

By V. GUDKOV

THE iron-ore deposits of Russia were estimated at 2,200,000,000 by the Russian Geological Survey, in 1910; but this estimate must be considered as being far too low. The estimate for Siberia, which had been explored very little for iron ore, was placed at about 27,000,000 tons. The exploration, in 1912-14, of the three iron deposits-Blagodat, Baakal and Kamensk-raised the estimate of the iron-ore reserves or the Urals from 282,000,000 tons to about 400,000,000 tons. Conservative estimates of the explored deposits made by the writer in 1915, gave the following figures: Southern Russia 900,000,000 tons, Ural Mountains 500,000,000 tons, Central Russia 900,000,- 000 tons, Siberia 100,000,000 tons, Caucasus 20,000,000 tons, or a total of 2,420,000,000 tons of iron ore, or 1,200,000,000 tons of pig iron.

Jan 1, 1921

By John V. Beall

Hard as the Revett quartzite are conditions governing the deep mines of the Coeur d'Al6ne. In fourscore years of mining, heat and pressure have been the rewards of preseverance. Such obstacles are the natural concommitant to search for ore at depth. But high cost and shortage of miners is a creeping frustration of the decade. These grim observations were made on a trip to the mines of the Coeur d'Al6ne in the first week of May. But the bouncy optimism of competent mining engineers and geologists overrides by far the tough conditions. This is the story of what they are doing. I think they are setting the stage for the wonder mines of tomorrow. I didn't meet all the people or see all the mines, so there are unfortunate gaps in the story. Then too, sometimes the muck and water blotched my notes, or I couldn't write fast enough or I was too tired. No matter. There is much to tell and, because it is basically a human story, I am flouting the rules of technical journalism and couching it in the neglected "I" person. First then, a little history . . . .

Jan 7, 1966

By E. J. KENNEDY

THE 142D MEETING of the Institute is rapidly shaping up with splendid prospects of a strong technical program and the lighter side of this annual occasion amply provided for. The date is February 20 to 23. The technical sessions will be held in the Engineering Societies building; the smoker-dinner, the informal dance, and the annual reception and dinner, at the Commodore Hotel, Monday, Tuesday and Wednesday respectively. The news to date on the technical side is as follows: Mining Methods-Subsidence The Mining Methods Committee has prepared an interesting program which will be divided into two sessions to be held early in the week. At the first there will be papers on mining methods and development, including a description of the "Sinking and Equipment of No. 2 Shaft at Minas de Matahambre," by Dudley D. Homer and R. H. Cromwell. They describe in considerable detail the equipment used and the practice followed in sinking this important shaft, giving detailed costs and performance figures. Hoist¬ing ?arrangements and mining practice at the "Red Ore Mines of the Woodward Iron Co. at Bessemer, Ala.," are described by Tenny C. DeSollar, superintendent of mines, in a second paper. At this session of the Mining Methods Committee, H. M. Roche and R. E. Crockett, of the Committee on Eastern Magnetite Mining and Milling Methods, will present their paper, "Iron Ore Mining at the Scrub Oak Mine." This mine is in the highlands of New Jersey about 40 miles west of New York City. Prof. Robert K. Warner of Yale University will present a paper on "The Selection of a Mining System," which should have an interesting discussion. Pierre R. Hines, of Portland, Ore., will present, with stereopticon slides, his paper on "The Owyhee Tunnels, U. S. Reclamation Project, Owyhee, Oregon," describing one of the recent irrigation undertakings.

Jan 1, 1933

By George F. Kunz

Jan 1, 1902

By GILBERT C. DAVIS

ANY thought of Morenci naturally includes its sister town of Clifton, its gateway to the outside world. Clifton, the country seat of Greenlee County, is the terminus of a branch line of the Southern Pacific railroad from Lordsburg, N.M. Carload freight incident to the Morenci operation moves from Clifton over Phelps Dodge?s standard-gauge industrial railroad. Private freight must be hauled by truck. These two communities fell far short of supplying adequate housing for the personnel concerned with the new operations so a new townsite, Stargo, was developed adjacent to Morenci. Here 234 housing units with garages have been built and twenty similar units have been erected near the reduction works.

Jan 1, 1942

By AIME AIME

DURING my senior year at college a professor said to his class that a student who failed to obtain a passing grade in that certain subject could not graduate with his class and that his diploma would be withheld until the failure had been removed. In that way for four years a diploma had been made to appear to us as the objective in attending college. We grew up to think that a diploma was the means of providing employment; consequently, a diploma could not be jeopardized and, heeding the professor's remarks, we resolved to put forth special efforts and make good. During one of our class periods this same professor digressed briefly from his prepared lecture in metallurgy and advised the boys to join a national technical society. He spoke with earnestness and sincerity. After class we students discussed those remarks. We concluded that the professor had not convinced us. We were already members of technical societies at school and saw no need of joining another. In fact, even up to that moment a society had never indicated to any of us that joining it had any relation to landing a job, and we were fully aware that joining another society meant paying out more money, for fees and dues, which money we then needed to buy food, clothes, and perhaps a new slide rule. Furthermore, we knew that joining a society was not part of the curriculum and, therefore, the diploma could not be withheld if we did not follow the advice. Our conclusion was that we would not join but would concentrate on our work that assured getting our diplomas.

Jan 1, 1936

By AIME AIME

THE 1941 fall meeting of the Iron and Steel and the Institute- of Metal, Division held at the Ritz-Carlton Hotel, Philadelphia, during the first three days (Oct. 20-22) of the National Metal Congress was well attended as usual, and the seven technical sessions and the joint round table on order-disorder transformations were this year of considerably more than routine interest. Despite unseasonably warm weather, a scarcity of hotels (there were rumors, apparently well-founded, that , some of the metal man attending the Congress had to stay in tourist camp), and a multiplicity of technical and other ions of the co-operating societies that gave the Congress this year the general air of a three-ring circus the A.I.M.E. sessions attracted audiences that ragged from seventy or eighty up to 350

Jan 1, 1941

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank' standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By Lap-yan Chan

Chan and Goodman (1983) presented a procedure for simulating joint traces and identifying key blocks on an excavation. This paper defines six measures of support requirements that characterize the number and dimensions of key blocks, taking into account the frictional properties of joints and actions of support systems. When correlated with case histories, these measures of support requirements can help in choosing an optimal design for shallow excavations in discontinuous hard rocks.

Jan 1, 1984

By Takashi Katsura, Avnulf Muan

Equilibrium relations in the system FeO-Fe2O3 Cr2O3 have been determined at 1300°C at oxygen pressures ranging from that of air (0.21 atm) to 1.5 x 10-11 atm. The following oxide phases have stable equilibrium existence under these conditions : a sesquioxide solid solution with corundum-type structure (approximate composition Fe2O3-Cr2O3); a ternary solid solution with spinel-type structure (approximate composition FeO Fe2O3-FeO Cr2O3) and a ternary wüstite solid solution with periclase-type structure and compositions approaching FeO. The metal phase occurring in equilibrium with oxide phase(s) at the lowest oxygen pressures used in the present investigation is almost pure iron. The extent of solid-solution areas and the location of oxygen isobars have been determined. ThE system Fe-Cr-O has attracted a great deal of interest among metallurgists as well as ceramists and geochemists. Metallurgists have studied the system because of its importance in deoxidation equilibria, ceramists because of its importance in basic brick technology, and geochemists because of its importance for an understanding of natural chromite deposits. Chen and chipman1 investigated the Cr-O equilibrium in liquid iron at 1595°C in atmospheres of known oxygen pressures (controlled H2O/H2 ratios). The main purpose of their work was to determine the stability range of the iron-chromite phase. Hilty et al.2 studied oxide phases in equilibrium with liquid Fe-Cr alloys at 1550°, 1600°, and 1650°C. They reported the existence of two previously unknown oxide phases, one a distorted spinel with composition intermediate between FeO Cr203 and Cr3O4, the other Cr3O4 with tetragonal structure. They also sketched diagrams showing the inferred liqui-dus surface and the inferred 1600°C isothermal section for the system Fe-Cr-O. Koch et al3 studied oxide inclusions in Fe-Cr alloys and also observed the distorted spinel phase reported by Hilty et al. Richards and white4 as well as Woodhouse and White5 investigated spinel-sesquioxide equilibria in the system Fe-Cr-O in air in the temperature range of 1420" to 1650°C, and Muan and Somiya6 delineated approximate phase relations in the system in air from 1400" to 2050°C. The present study was carried out at a constant temperature of 1300° C and at oxygen pressures ranging from 0.21 atm (air) to 1.5 x 10-11 atm. The chosen temperature is high enough to permit equilibrium to be attained within a reasonable period of time within most composition areas of the system, and still low enough to permit use of experimental methods which give highly accurate and reliable results. These methods are described in detail in the following. I) EXPERIMENTAL METHODS 1) General Procedures. Two different experimental methods were used in the present investigation: quenching and thermogravimetry. In the quenching method, oxide samples were heated at chosen temperature and chosen oxygen pressure until equilibrium was attained among gas and condensed phases. The samples were then quenched rapidly to room temperature and the phases present determined by X-ray and microscopic examination. Total compositions were determined by chemical analysis after quenching. In the thermogravimetric method, pellets of oxide mixtures were suspended by a thin platinum wire from one beam of an analytical balance, and the weight changes were recorded as a function of oxygen pressure at constant temperature. The data thus obtained were used to locate oxygen isobars. The courses of the latter curves reflect changes in phase assemblages and serve to supplement the observations made by the quenching technique. 2) Materials. Analytical-grade Fe2O3 and Cr2O3 were used as starting materials. Each oxide was first heated separately in air at 1000°C for several hours. Mixtures of desired ratios of the two oxides were then prepared. Each mixture was finely ground and mixed, and heated at 1250" to 1300°C in air for 2 hr, ground and mixed again and heated at the same temperature for 5 to 24 hr, depending on the Cr2O3 content of the mixture. A homogeneous sesquioxide solid solution between the two end members resulted from this treatment. A Part of some of the sesquioxide samples thus prepared was heated for 2 to 3 hr at 1300°C and oxygen pressures of 10-7 or 1.5 x 10-11 atm. Reduced samples (either iron chromite

Jan 1, 1964

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By Z. T. Bieniawski, E. Unal, H. Reginald Hardy

INTRODUCTION Rock bolts are a major means of support in underground coal mines in the United States. However, two of the most crucial problems facing the mining engineer today are that of finding a well defined and standard method for testing the anchoring ability of rock bolts, and of selecting the most suitable type of rock bolt and bolting pattern for a particular mine or specific mine section (Anon., 1982). Such selection requires not only an understanding of the behavior of the rock mass and the rock-bolt unit itself, but also a knowledge of the basic mechanisms by which rock bolts provide support while they interact with the rock mass during various field loading conditions. A recent study in this area has shown the inadequacy of present methods used in selecting and testing of rock bolts and the lack of clearly defined guidelines for safe and economical design of bolting patterns (Bieniawski, et al., 1980). The present paper describes a research study aimed at developing laboratory instrumentation and associated techniques for the evaluation of bolt-rock interaction. The instrumentation system developed, procedures followed during various experiments, and typical results from a series of studies carried out on mechanical bolts are presented. DEVELOPMENT OF THE ROCK BOLT TESTING FACILITY General A block diagram of the experimental facilities are shown in Fig. 1. The system consists of three main sections. The first

Jan 1, 1982

By C. E. Berry

NATURAL stone or manufactured porcelain pebbles are used as the grinding elements in pebble mills and the mills are lined with stone or porcelain blocks. Steel balls usually form the grinding medium in ball mills, and the mills may he lined with steel. Pebble mills are used to avoid contamination by metal of the material being ground, to avoid rapid wear due to corrosion, and for other specialized reasons. Belgian silex (silica) blocks formerly were used widely for lining pebble mills, because of their good resistance to wear, light color, and low cost, but the importation of these blocks was suspended early in the war. The stocks of Belgian silex diminished so rapidly that it was found desirable to compare the properties of a number of domestic substitutes for use in critical operations. Accordingly, a study was made to determine the best substitutes for fine grinding of white pigment and for certain heavy-chemical process work such as the disintegration of phosphate rock in weak phosphoric acid solution. A comprehensive survey of substitute lining materials was not contemplated. It was stipulated at the beginning of the investigation that only materials on the market, available in large quantities, would be tested and that these should be reasonable substitutes from a wear-resistance viewpoint as determined from known physical characteristics. Marble and limestone, for example, could be eliminated immediately. Quartzite, granite and porcelain were selected as likely substitutes for Belgian silex and were subjected to quality tests. MATERIALS TESTED I. Belgian Silex.-Sample blocks of a standard grade were taken from crates in which they had been imported. The stone was light gray in color and contained inclusions of small clusters of quartz crystals as well as light colored portions that might be calcite. This was a siliceous rock which appeared to be of igneous origin. 2. Quartzite.-Samples of quartzite were obtained from a quarry in Minnesota. The blocks exhibited a crystalline fracture. The stone was pink in color and composed of fine quartz crystals bound together with a siliceous cement. 3. Granite A was a fine-grained granite quarried in South Carolina. 4. Granite B was coarse-grained granite quarried in South Carolina. 5. Granite C was a coarse-grained granite quarried in North Carolina. 6. Porcelain A.-Sample blocks of the pebble-mill lining material were obtained direct from the manufacturer. It was white in color and of lower specific gravity than the natural materials. It did not have a crystalline structure. 7. Porcelain B.-Sample pebble-mill lining blocks of the porcelain were received direct from the manufacturer. It was white

Jan 1, 1946

By W. T. Turrall, D. Porter

THE crystal laboratory, Dept. of Physics, Massachusetts Institute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF2) for use in growing synthetic CaFe2 crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF2 crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO2, BaSO4, CaCO3, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, -4 mesh +10 mesh, from a feed containing over 99 pct CaF2. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1952