Search Documents

By E. O. Karenna, A. D. Smigelskas

This is the third paper in a series on the diffusion of zinc in alpha brass.' At the time of the first paper it was accepted that diffusion in a substitutional type of solid solution depended upon an equal interchange of solute and solvent atoms across the diffusion interface (or past a given lattice reference point). Discrepancies in the size of the areas under the diffusion curves on each side of the interface, if observed, were explained on some other basis than the fact that the solute atoms might cross the diffusion interface without an equal number of solvent atoms diffusing across the interface in the opposite direction. The second paper presented evidence indicating that zinc atoms in alpha brass diffuse across the interface more rapidly in one direction than the copper atoms diffuse across the interface in the opposite direction. This phenomenon forced the interface to move in the opposite direction of the diffusion of zinc atoms to provide space for the additional zinc atoms dissolved in the alpha brass. That the interface and columnar grain structure on one side would remain intact during this mass movement was not expected; how ever, it is gratifying that they did. While the evidence was sufficiently satisfying to the author, it was decided that additional experiments were in order to prove that zinc diffuses more rapidly than copper in alpha brass. It is the purpose of this paper to present the results of these experiments. Procedure A bar of 70-30 wrought brass was selected, to avoid the relatively large volume change in going from beta to alpha brass as in the previous investigation. A bar 7 in. (18-cm.)* long and about 3/4 in. (1.9 cm.) wide was surface ground and polished with abrasive paper on plate glass to 0.4184 0.0002 in. (1.062j + 0.0005 cm.) thick. Six0.00j-in. (0.013-cm.) diameter molybdenum wires, chosen because of their very low solubility in coppcr and alpha brass, were strctched lengthwise along each of the two plane surfaces. Glass tubes placed at right angles to the wires every 1/2 in. held the wires tightly against the brass. The sample was then emersed in an acid copper sulphate plating bath and electroplated to a depth of about 0.020 in. (0.050 cm.) copper on all sides. The glass tubes were no longer necessary to hold the molybdenum wires in place and were removed. The sample was then electroplated to a depth of

Jan 1, 1947

By C. L. Burrill

The forecasts presented in this paper constitute an attempt by the writer to predict the pattern of the consumption of petroleum products in the United States during the period of transition from war to peace. Although, in preparing the estimates, secular trends were not overlooked, greater emphasis was placed upon considerations of a cyclical character, or upon influences which might be peculiar to parts of the period. The estimates do not extend beyond the year 1950 because by then conditions in the industry should have returned to normal. The consumption of petroleum products is affected, of course, by changes in the condition of business in general. Before estimates of petroleum consumption could be prepared, therefore, it was necessary to predict the pattern of general business during the period under review, particularly the economic series that in the past have shown the closest relationships with petroleum consumption. It is the writer's view that business activity in this country (as measured by industrial production) will be higher on the average during the period between the end of the war and the year 1950 than it ever was before during a peacetime period of the same duration. When the war is over, consumers will have saved amounts of money that will be very large as compared with any previous accumulations. There is little question, therefore, as to the financial ability of consumers to purchase goods. The production of many durable consumers' goods, such as automobiles, refrigerators and radios, has been completely stopped since early in the war; also, many semidurable and nondurable consumers' goods have not been available in the quantities or the qualities desired. There is considerable needi therefore, for consumers to purchase goods after the war. The important question is whether consumers will purchase goods in "1arge enough quantities to keep our economy running at a high level. The writer answers this question in the affirmative. The mere existence of very large consumer savings lends considerable support to this view because, with such backlogs of " security," consumers can afford to spend more of their current earnings than they otherwise could. Also, several polls have been taken, which indicate that consumers expect to buy large quantities of a variety of goods. Some of the savings, therefore, probably will go into current consumption. Even though this percentage is relatively small, so that the bulk of the funds accumulated by consumers during the war continues to remain as savings during the period under review, spending should be great enough to start the production cycle and keep it

Jan 1, 1945

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By R. M. Waterstrat

The phase VPt has been reported to have a crystal structure of the B19 (AuCd) type at low temperatures.''' A recent investigation3 has indicated that this phase forms by an ordering reaction from the disordered fcc Pt(V) solid solution which is stable at high temperatures. olander4 has shown that there exists a close structural relationship between the orthorhombic B19 structure and a fcc structure possessing the L1 , (CuAu) type of atomic ordering. One may derive the B19 structure by a shear-like displacement of the atoms in the (002) plane of the ordered fcc lattice along the (010) direction through a distance equal to one eighth of the unit cell dimension, see Fig. 1, followed by an orthorhombic distor; tion of the cube axes such that a = 2.693A. h = 4.413A. and c =4.767A (estimated uncertainty 0.005A). Filings of this phase were produced by grinding a VPt alloy having the B19 structure with a diamond dental grinding disc. When these filings were subjected to X-ray diffraction examination, a pattern of a severely cold-worked fcc structure was obtained. higher solution temperature used (1200 C) or to a much lower oxygen pressure than he reported, due to transfer through many bends and tubes in his complicated apparatus. An interesting observation was made when an oxygen addition was attempted in a cylindrical sample of columbium in the cold worked condition rather than in the annealed condition. The interior of the sample re-crystallized during the oxygen addition at 900°C. The periphery, however. (1 mm) did not recrystallize. A similar sample without oxygen recrystallized throughout the entire cross section. It appears that the re-crystallization is hindered by interstitial oxygen. Presumably, the interior recrystallized before appreciable oxygen could diffuse into the core. This work was supported by the United States Atomic Energy Commission. When the filings were annealed in a high vacuum furnace for 15 min at 110O0C, however. they returned to the B19 structure perhaps as a result of reordering. Subsequent less-severe cold-working of these filings by grinding in a hardened steel mortar and pestle at room temperature produced a transformation into a cold-worked L1, structure which was slightly tetragonal. Thus it appears that the degree of deformation may influence the final structure. Considerable line-broadening was observed in X-ray diffraction patterns obtained from the cold-worked filings and therefore no attempt was made to obtain accurate lattice parameters. Vacuum annealing treatments at 1100'C intended

Jan 1, 1970

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By Irving M. Symonds

Compania Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Provi-dencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Penoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. Ore Treated The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopy-rite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I.

Jan 1, 1943

By Irving M. Symonds

COMPAÑIA Minera de Peñoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Peñoles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torreón, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By Irving M. Symonds

COMPA[N]IA Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Pe[n]oles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torréon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By H. L. Riley, B. W. Gandrud

A froth flotation unit was added to the DeBardeleben Coal Corporation's Empire washer at Empire, Alabama, in the fall Of I94O following an investigation of possible ways and means of recovering coal values from settling-tank overflow or slurry. Officials of the DeBardeleben corporation hoped that some practical and reasonably economical way could be found for recovering fine coal from overflow water, although there had as yet been very little progress along this line in the Alabama coal fields. The Bureau of Mines was asked to cooperate in the project through its Southern Experiment Station, at University, Alabama. This paper presents a brief description of the process and the installation that resulted from the investigation of the overflow water or slurry problem at the Empire mine. The experimental data include' as a Part of this Paper were obtained during the course of the investigation in 1940 Since that time, however, the flotation unit has been running more or less continuously without significant operational changes and is still Performing pretty much in accordance with the data obtained in 1940. Flowsheet at Empire and Type of Coal Treated The Empire mine is developed on the Black Creek bed near the the border of the Warrior field. The coal in this bed is extremely low-ash and although there is an almost complete absence of bone coal and partings, the bed is so thin that, with mechanized mining, a high percentage of rock from roof and floor inevitably gets into the run-of-mine coal. The thickness of the Black Creek bed throughout the part of the Warrior field in which it is mined extensively is rarely over 30 in. and probably would average about 25 in, the coal is of the high-volatile A rank and of excellent quality, but as a result of admixture of roof and floor material, the run-of-mine product usually contains I ; to 20 pct rock by weight. he following is a proximate analysis on an "as-received " basis of a typical seam sample from the Empire mine:' moisture, 3.0 pet; volatile, 34.6 fixed carbon 58.3; ash, 4.1 This sample shelved 15,070 Btu per pound and 0.9 pct sulphur on a moisture-and-ash-free basis. In the Empire preparation plant the lump sizes above 3 in. are removed and hand-picked on a Marcus conveying Screen, the 3 to ? -in. size is removed by vibrating screens and washed in two Montgomery single-cell jigs, and the ?-in. to o slack is cleaned on four diagonal

Jan 1, 1949

By Herbert M. Wilson

We of the employer class represent labor in the social organization and in industry just as truly as do those who labor only with their hands, and, because our labor is chiefly with our brains, the duty is all the more imposed upon us to use those gifts in which we excel in helping steer a clear course through the turbulent waters in which we are now enmeshed. Only their selfish engrossment in the daily tasks they were employed to perform could possibly have permitted the great majority of the intelligent and industrious German people to become terrorized by a handful of the idle, the vicious, and the criminal, whom the elections to the National Assembly showed to be in as pitiful a minority as they are in Russia, in this, and in other countries. It is the leisure unemployment of the I.W.W.'s, the Bolsheviki, and the Sparticans that has enabled them to devote their whole time to a concerted and aggressive struggle against the great majority of those of the world's workers who are unorganized, and who are therefore even in opposition one to the other. In union there is strength, and this was never better illustrated than by these conditions. The great fallacy of our previous attitude toward social and industrial problems has been the belief that labor, by which we commonly mean organized or physical labor, is something antagonistic to and having a different object in life from that great body of unorganized laborers who work with their brains. Our difficulty has been our lack of will or opportunity to think. The hurry of our daily struggle to earn our livelihood under the nerve-racking pressure of modern civilization has left us no opportunity for quiet thought and study. The physical laborer, and above all the laborer in the mines, on the other hand, has all his hours of toil in which to think over, in all their varied aspects, those problems that concern his immediate, personal well-being. As a result he has arrived at perhaps a more true appreciation of the facts of life in their relation to social and industrial conditions than we. Have we not too readily adopted the view that, as the managers of industry under the direction of capital, it has been our duty to think and act in opposition to labor, rather than to realize that we also are laborers, have like aspirations, and should participate in a free and aggressive solution of these problems rather than leave their solution

Jan 1, 1919

By H. E. McCoy, C. J. McHargue

Single crystals of columbium containing various levels of oxygen, nitrogen, carbon, or hydrogen were deformed by slaw compression and impact loading at -196°C. For the slow deformation rates. 1500 to 1900ppm oxygen, 500 pprn nitrogen, or 150 to 200 ppm carbon completely suppressed mechanical twinning. Hydrogen in concentrations to 1000 ppm had no apparent effect on ease of twinning. Impact loading caused twins to form at all levels of contamination studied, and cleavage mucking on (100) planes occurred in specimens having higher interstitial contents. It is well established that, under some conditions, the bcc metals vanadium, columbium, tantalum, chromium, molybdenum, tungsten, and iron deform by formation of mechanical twins. In general it has been accepted that high strain rates, low temperatures, and large grain sizes are conducive to this kind of deformation.' Since interstitial impurity atoms have a relatively large effect on slip in bcc metals, one might sus- pect a similar effect on twinning. This could occur directly by the interstitials affecting the nucleation or growth of the twins or indirectly from their effect on slip. It has often been argued that the large increase in yield stress caused by interstitial elements enables the effective stress to exceed that necessary to cause twinning. The twinning stress has always been thought to be higher than the stress necessary to cause slip in pure metals.2 simonsens and Tipper and Hall4 found profuse twinning in very pure a iron even at room temperature, whereas Low and Fueste15 and Churchman and tottrell' observed twins in a iron containing carbon but none in highly decarburized specimens. McHargue7 reported mechanical twins to form readily in vanadium which contained 390 ppm interstitigs, while Clough and Pavlovic8 found twins only in the one or two grains adjacent to the fracture surface in vanadium which contained 1500 to 1700 ppm interstitials. In columbium, McHargue9 found high-purity single crystals to twin easily whereas Churchman,10 Adams, Roberts, and mallman,11 and Johnson12 studied less pure material and found far fewer twins. Although the results of Leadbetter and Argent13 showed oxygen to inhibit twinning, a study by sheely14 indicated the opposite to be true. Chromium exhibits this mode of deformation15,16 but there are no data regarding impurity effects. Lawley, Van den Sype, and Maddin17 observed twins in very pure molybdenum single crystals deformed at 77°K but none in less pure crystals. The work by Cahn18 and

Jan 1, 1963

By W. A. Ver Wiebe

The year 1939 in Kansas, with a production of 57,944,300 bbl. from 19,669 wells, shows a slight recession from the peak of oil production reached the previous year, when slightly over 59,000,000 bbl. of oil was marketed. The previous peak had been reached in 1917 with 45,451,000 bbl. marketed. Another still earlier peak had been reached in 1904, when slightly less than 5,000,000 bbl. was produced and sold. The production of gas probably reached a new peak during 1939 with a total of over 69 billion cubic feet. Between the peak of the year 1908, when over 80 billion cu. ft. was produced, and that of 1939 the production dropped to 16 billion cu. ft., in the year 1921. During the year 1458 wells were drilled. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or recompleted in a different geological horizon. Nearly 75 per cent (1029) of the total number of wells were completed as commercial oil wells (824 in western and 205 in eastern Kansas). The commercial gas wells completed number 71, of which 24 are in eastern Kansas and 47 in western Kansas. The remaining completions include 154 dry holes in eastern and 204 dry holes in western Kansas. Based on daily potential capacity the new discoveries of the year accounted for a cumulative initial production of 264,000 bbl. in eastern and 1,158,827 bbl. in western Kansas. It is interesting in this connection to note that the number of wells completed in the state rose gradually to a first peak in 1904, when 2782 were drilled. The number dropped off rapidly to 368 three years later, but rose to the second and highest peak in 1918, when 4671 wells were completed. In the period between 1904 and 1912 more gas wells than oil wells were completed. Between the high peak of 1918 and the somewhat lower peak of 1937, the low point was reached during 1931 with the completion of only 470 wells. In the matter of new pools discovered, Kansas again ranks high. The exact number depends somewhat upon the interpretation of a "new" area—whether it should be called a new pool or a long extension of an older pool. In some places this determination cannot be made until more wells are drilled within the area. Therefore, the figures given

Jan 1, 1940

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By M. Muskat

Calculations are reported on the differential sensitivity of the updip invasion of oil strata of varving permeability to the driving pressure differential. It is assumed that the water-oil interfaces advance with sharp fronts, or that the microscopic displacement efficiency is independent of rate and capillary pressure effects. It is found that, under such conditions, limitations of withdrawal rates will not greatly inhibit the "fingering" and bypassing tendency through high permeability strata unless the differential fluid head across the original oil column is of the order of or exceeds about 80 per cent of the driving pressure differential. In practice, such restrictions will be feasible only for oil reservoirs and aquifers of high permeability and dip, but may develop automatically under combined gas injection and water drive operations. INTRODUCTION A commonly expressed view regarding the intrusion of edge-waters into oil producing formations is that the geometry of such advance is rate sensitive. Specifically, it has been suggested that high rates of advance, stimulated by rapid withdrawals, will lead to "fingering" and an irregular type of invasion, whereas at low withdrawal rates the water encroachment will be more uniform. Two factors tend to support this view. One is the resultant effect of capillary pressure and gravity gradients in the displacement processes' involved in water intrusion, which are magnified at low rates of flow so as to improve the recovery efficiency. The other is the direct retarding effect of the rising water head as it advances upslope into the producing area. Capillary pressure forces give rise to a rate sensitivity of the oil recovery by water displacement in uniform strata as well as differential effects in non-uniform formations. These are basically independent of the effect of gravity and would also occur in horizontal beds or when the oil and water have the same density. Unfortunately, however, the fundamental equation describing the displacement process under the action of capillary pressures can be solved only by numerical or graphical procedures, and moreover the solutions are sensitive to the character of the capillary pressure and relative permeability curves.* On the other hand, the direct effect of gravity can be given a formal analytical solution if the simplifying assumption is introduced that the water advances with sharp fronts in the individual uniform strata. It depends on the absolute permeabilities of the water invaded zones and hence results in a rate sensitivity of the differential invasion in stratified media. Although a tieatment of this factor alone will not give a complete evaluation of the effect of rate on water intrusion in non-uniform pays, it should provide at least a semiquantitative measure of the sensitivity of "fingering" to withdrawal rate. Such a treatment will be presented in the following sections. GENERAL THEORY The basic element of the theory is the history of water advance updip in a uniform stratum (Fig. 1). In contrast to the assumption of constant flow rate, generally made in the analysis of displacement processes, we shall assume here that

Jan 1, 1951

By O. J. C. Runnalls, L. M. Pidgeon

J. M. Blocher, Jr. and I. E. Campbell (Battelle Memorial Institute, Columbus, Ohio)—Since the de Boer-Van Arkel process for making titanium metal involves a number of steps in a fairly compact unit, it is difficult to determine simply which of the steps is rate controlling. In any statement as to which step constitutes the rate-controlling process, qualifications appear to be in order. It is possible to design a reaction bulb in which any one of a number of steps is made to be controlling. I—With the filament removed some distance from the crude, as in the case of the authors' experiments, the interdiffusion of iodine and iodide may be controlling. 2—If, as is usually done, the crude metal is placed in a perforated cylindrical basket, or as a briquetted mass, in close proximity to the filament, the rate of deposition is increased (we obtained rates of deposition 5 to 10 times those cited in the authors' paper), and another rate-limiting factor, such as the reactivity of the crude, may take over. In this regard, we have noticed radically different rates of deposition with different crudes, and with crudes in various stages of exhaustion. 3—With a very reactive crude metal and with optimum practical geometry, still another process may be controlling. It is felt that this is a diffusion process in the immediate vicinity of the filament involving the fundamentally adverse situation of a net flow of particles away from the filament. The separate experiments on the reactivity of iodine with titanium are interesting but somewhat inconclusive. Data is still needed on the partial pressure of iodine in an operating decomposition bulb. A knowledge of the gradient of iodine partial pressure from the crude to the filament would be particularly enlightening. Optical absorption may be a useful technique here. Accurate measurements of the total pressure within a decomposition bulb under various conditions would be quite revealing. Preliminary measurements have been made at Battelle in following this line of attack. It is interesting to note that the authors' data on the temperature dependence of deposition rate indicate that the overall rate is not controlled by the kinetics of the decomposition reaction at the filament: TiI1 ? Ti + 4I Any reasonable estimate of the activation energy of this reaction would, if its kinetics were controlling, dictate a much greater temperature dependence than is observed here. The authors apparently attribute the drop in deposition rate (eventually to zero) with increased TiI4 pressure solely to a decrease in diffusion rate. However, there is an equilibrium factor involved here that must not be overlooked. As the partial pressure of TiI4 is increased, a point is reached where, due to the competing reaction of the tetraiodide with titanium to form lower iodides, the equilibrium partial pressure of titanium is reduced to the point that it equals the vapor pressure of titanium at the filament temperature and the deposition rate falls to zero. This effect would

Jan 1, 1953

By R. A. Perry

A speiss is an artificial arsenide, sometimes an antimonide, formed in lead smelting, smelting of oxide copper ores, and in some lead-refining operations. The production of speiss is closely allied with the amount of arsenic and metallic iron in the blast-furnace charge, while dross is produced mostly from the copper and sulphur, with varying amounts of antimony, arsenic and nickel. Most speiss is essentially an iron arsenide containing some sulphur, copper and nickel, if these elements are present in the furnace. The recent introduction of the soda treatment of lead drosses has produced a speiss high in copper. Speiss is not miscible to any extent with molten copper, lead, matte or slag. Miscibility increases with temperature. This property of the speiss is clarified in the latter part of this paper. Most speisses are produced in conjunction with matte and their sulphur content points to the solubility of matte in speiss. . Some plants have insufficient speiss to warrant separate treatment. When arsenic is high in the blast-furllace charge, there may be sufficient speiss to tap separately from the first settler. Arsenic From the foregoing, it is obvious that a study of the treatment of speiss would not ,be complete without consideration of arsenic. Inasmuch as perhaps go per cent of the blast-furnace feed may be sinter, a definite knowledge of the properties of arsenical ores and compounds that go in to the roaster and sinter feeds is of value. Lcad smelters obtain their arsenic from ores and concentrates, as well as from flue dusts shipped from other plants, particularly copper smelters. The percentage of arsenic in ores is usually low, although occasional lots of high arsenical products are smelted. These crude ores may be sulphides, as arsenopyrite; or oxides like scoiodite, which carry gold or lead minerals. The small amount of arsenic in the original ores received is greatly increased by a circulating load of arsenic in secondary products at are resmelted for their lead or precious metals. More important than the arsenic present directly in the concentrates treated is that in fumes and dusts that may originate in the blast furnace or sinter plant of the lead smelter, or may come from a copper smelter as lead-bearing converter fume or roaster dust. Thus the lead smelter not only must treat its own arsenic but is compelled to handie that from some copper and perhaps other lead plants. Where copper and lead plants exchange products, each plant may be forced to re-treat part of the arsenic it has shipped ,outside its own confines. Speiss from the lead blast furnace contains chiefly iron and arsenic with some lead, copper and sulphur and often appreciable amounts of gold and silver. If its copper content is sufficient this speiss may be sent to the copper smelter where usually it is treated in the converter and the copper is separated as blister. Much of the arsenic and most of the lead are recovered as converter fumes

Jan 1, 1944

By C. H. Snyder

Tlie paper deals with details of construction of the Colmol, including improvements in design that will be incorporated in new models. These improvements are results of problems encountered and worked out in experimental operation with the unit. Also included is a descriptive plan of operating where roof and air conditions are of the worst. A summary of production results from the machine is presented. THE various units used in conventional mining are well-built. Generally the universal under -cutter, driven by approximately 50 hp, weighs approximately 25,000 lb, and is a very strong piece of machinery. The drilling machine is not as husky as an undercutter, generally is driven by approximately 15 hp, weighs about 9000 lb, but is a well-constructed, sturdy mechanism. The loader, usually 60 hp, weighs approximately 24,000 lb, and certainly is a strong, rugged unit. The working parts of all three of these sturdy conventional units have been made of tough steel alloys for some time. With the use of three machines having a combined horsepower of approximately 125, with a combined weight of approximately 60,000 lb, and with the possible inherent advantage of single purpose machines performing a single function, the use of considerable explosives has been required to complete the conventional mining cycle. It was therefore our thought, upon conception of the first Colmol,* a machine which was to do the work accomplished by the three conventional units plus explosives, that it must be a rugged mechanism. Now, after building several units, after going through many and varied experiments, and after the expense of some million-odd dollars, we find we have observed and learned nothing that contradicts our original thinking. A continuous miner, if it is to give satisfactory performance, must be a rugged piece of machinery. Ruggedness has been, and is constantly, in the minds of our engineers in designing the Colmol. Improvements where they have been required have been in the direction of more weight, more horse power, better alloys, bigger hydraulic pumps and motors; in short, always, toward more torque, greater strength, more ruggedness. Now not only the finest steel alloys are utilized but more than 100 Timken roller bearings are used. The following is some pertinent data on models being built and to be built: The low unit: Cutting height, 30 to 42 in. By changing the upper gear case the maximum cutting height can be increased to 61 in., giving a variable cutting height of from 30 to 61 in. Width of cut, 9 ft 6 in. Width of body, 75 in. over tracks. Height of body, 271/2 in. Overall length, 23 ft. Driven by three 50-hp motors or a total of 150 hp. Weight, 26 tons. The intermediate unit: Cutting height, 451/2 to 72 in. Width of cut, 9 ft 8 in. Width of body, 77 in. over tracks. Height of body, 43 in. Overall length, 26 ft. Driven by three 70-hp motors or a total of 210 hp. Weight, 35 tons.

Jan 1, 1951

By M. Muskat

Calculations are reported on the differential sensitivity of the updip invasion of oil strata of varving permeability to the driving pressure differential. It is assumed that the water-oil interfaces advance with sharp fronts, or that the microscopic displacement efficiency is independent of rate and capillary pressure effects. It is found that, under such conditions, limitations of withdrawal rates will not greatly inhibit the "fingering" and bypassing tendency through high permeability strata unless the differential fluid head across the original oil column is of the order of or exceeds about 80 per cent of the driving pressure differential. In practice, such restrictions will be feasible only for oil reservoirs and aquifers of high permeability and dip, but may develop automatically under combined gas injection and water drive operations. INTRODUCTION A commonly expressed view regarding the intrusion of edge-waters into oil producing formations is that the geometry of such advance is rate sensitive. Specifically, it has been suggested that high rates of advance, stimulated by rapid withdrawals, will lead to "fingering" and an irregular type of invasion, whereas at low withdrawal rates the water encroachment will be more uniform. Two factors tend to support this view. One is the resultant effect of capillary pressure and gravity gradients in the displacement processes' involved in water intrusion, which are magnified at low rates of flow so as to improve the recovery efficiency. The other is the direct retarding effect of the rising water head as it advances upslope into the producing area. Capillary pressure forces give rise to a rate sensitivity of the oil recovery by water displacement in uniform strata as well as differential effects in non-uniform formations. These are basically independent of the effect of gravity and would also occur in horizontal beds or when the oil and water have the same density. Unfortunately, however, the fundamental equation describing the displacement process under the action of capillary pressures can be solved only by numerical or graphical procedures, and moreover the solutions are sensitive to the character of the capillary pressure and relative permeability curves.* On the other hand, the direct effect of gravity can be given a formal analytical solution if the simplifying assumption is introduced that the water advances with sharp fronts in the individual uniform strata. It depends on the absolute permeabilities of the water invaded zones and hence results in a rate sensitivity of the differential invasion in stratified media. Although a tieatment of this factor alone will not give a complete evaluation of the effect of rate on water intrusion in non-uniform pays, it should provide at least a semiquantitative measure of the sensitivity of "fingering" to withdrawal rate. Such a treatment will be presented in the following sections. GENERAL THEORY The basic element of the theory is the history of water advance updip in a uniform stratum (Fig. 1). In contrast to the assumption of constant flow rate, generally made in the analysis of displacement processes, we shall assume here that

Jan 1, 1951

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

By F. X. Spiegel, D. Bardos, Paul A. Beck

Ti6NileSi7)G is known to be cubic, with 116 atoms in the unit cell. In the present work four new G sili-cides were found with other transition elements and five G germanides. The titanium-group elements are very efficient in forming G phases. The vanadium -group elements are somewhat less efficient, and the chromium-group elements do not form any. Cobalt can replace nickel in most cases, but it is somewhat less efficient. Iron was not found to form any G phases. Germanium is somewhat less efficient than silicon. The (TiNiSi)E phase has been previously identified by Westbrook. However, its crystal structure has not been determined. In the present work the E phase was found to have an orthorhombic unit cell with lattice parameters a. = 7.02, bo = 5.18, co = 11.11A. A large number of other E phases were found at the same stoicheometric ratio in ternary systems of silicon and germanium with transition elements. Lattice parameters similar to those for TiNiSi were measured. The number of atoms per unit cell is estimated at 30 to 36. The vanadium-group elements are somewhat more efficient in forming the E phase than the titanium-group elements. Chromium-group elements were not found to form any E phases. Cobalt is somewhat less efficient than nickel, and iron is less efficient than cobalt. Germanium is not as efficient as silicon. ThE ternary silicide designated as G-phase was first identified by Beattie and versnyder1 and by Beattie and Hagel2 at the approximate composition TiNi2Si. Westbrook et al.' gave the composition as Ti2Ni7Sis. This phase was found to be fcc with a. = 11.201A and 116 atoms per unit cell. Beattie4 and more recently independently Hladishevskii, Kripyakevich, Kuzma, and Teslyuk5 were able to show that this structure is isotypic with MgeSi7CuLe and Th6Mn23. The latter structures had been determined by Florio, Rundle, and snow,' Nagorsen and Witte,7 and Bergman and Waugh.8 According to the crystal structure, Ti8Ni6Si7 may be considered as the ideal composition. The Russian investigators5 identified six additional ternary phases isotypic with Ti6Ni6Si7, in which titanium is replaced by Mn, V, Nb, Ta, Zr, and Hf, and one, namely MneNil6Ge7, in which germanium replaces silicon. They also found that Cr6Ni6Si7, which does not occur as a ternary phase, can be stabilized by replacing 1 at. pct of the Cr by V, Mn, or Ta. Another ternary silicide was found by Westbrook et al.3 at the composition TiNiSi, and it was designated by them as the E phase. The crystal structure of this phase has not been deter-

Jan 1, 1963