Search Documents

By J. G. Richardson

The performance of laboratory water floods is compared with the flooding behavior calculated by the Buckley-Leverett techniques from steady-state relative permeability-saturation relations. Both the steady-state and unsteady-state experiments were conducted on the same sand-packed column. Relative permeabilities were calculated by the Welge technique from the unsteady-state waterflooding displacement experiments and compared with those measured by steady-state techniques. An evaluation of the various calculation procedures was made. It was demonstrated that steady-state relative permeabilities could be used to calczcJate waterflood performance. INTRODUCTION To calculate the waterflooding behavior of a given reservoir, relative permeability-saturation relations of the reservoir rock are required. These relative permeabilities are commonly measured on core samples by steady-state experiments such as the Penn State technique.' The relative permeabilities obtained in steady-state experiments are calculated from oil and gas flow rates and pressure drops measured under conditions of equilibrium distribution of oil and water in the pore spaces with slow approach to equilibrium. On the other hand, in water floods the water saturation at a given point changes rapidly with time as the flood front passes. Extensive research2 has shown that the steady-state relative permeabilities to oil and water are independent of the rate of flow and the fluid viscosities. Research has also demonstrated that the waterflooding performance of homogeneous sands uniformly contacted by water is independent of rate when capillary pressure gradients, which are important in short laboratory columns, are made negligible. However, there is little experimental data in the literature comparing relative permeabilities calculated from steady-state flow experiments with those calculated from flooding experiments. In this paper, the production data of two water floods and the relative permeabilities calculated from a series of steady-state experiments on an unconsolidated sand column are presented along with the comparisons calculated by the Buckley-Leverett and by the Welge techniques. The purpose of this study was to determine if steady-state relative permeabilities could be used to predict the waterflooding performance. This study also permitted an evaluation of the Buckley-Leverett and Welge calculation procedures and allowed an insight into the nature of microscopic displacement of oil by water. EXPERIMENTAL APPARATUS AND PROCEDURE The apparatus used in this investigation was a Lucite column 1 ft long and 11/2 in. in diameter. A drawing of the apparatus is shown in Fig. 1. Six pressure taps were evenly spaced along the top of the column to measure the oil pressures. Three pressure taps fitted with small porous disks were spaced along the side of the column to measure water pressure. Water was admitted to the inflow face of the sand through a porous disk while oil was admitted through a hole in the porous disk and distributed to the face of the sand by grooves machined in the porous disk. Retainer screens of 325-mesh stainless steel were cemented over the inlet and outlet ports and the pressure taps to prevent loss of sand. The column was packed with a clean dry sand all of which was finer than 200 mesh. Next, the sand was saturated with a solution of 150,000 ppm sodium chloride solution. The column was weighed dry and water-saturated to obtain data for the calculation of the pore volume. A 151-cp oil was then injected into

Jan 1, 1958

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases'-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-'' Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949

By Boyd Guthrie, J. D. Lankford

A progress report on the oil-shale and shale-oil processing research program at the U. s. Bureau of Mines Oil-Shale Demonstration Plant. Legislation providing for the program and aims are briefly noted. The remoteness and rugged nature of the terrain at the plant site are important factors in construction and operations. Large-scale units now in operation are the crushing plant and two 40-ton N-T-U retorts. These are described in detail. Under construction are several retorting pilot plants and a 200 bbl per day refinery. The refineiy incorporates several types of thermal operation, three-stage low-temperature acid treating, doctor sweetening and rerunning. Data are presented on typical N-T-U retort runs. Yields of 90 to loo pct of assay are realized on 30 gal to the ton shale with a retort cycle time of 18 hr. Data also are presented showing a comparison of a Mid-Continent petroleum and N-T-U shale oil. This comparison indicates that shale oil has a high pour point, low API gravity, and contains about 0.8 pct sulphur and 2 pct nitrogen. The naphtha fraction contains 3 pct tar acids, 9 pct tar bases and jo pct olefins. The problems involved in refining shale oil into usable products are discussed in detail. Introduction The Bureau of Mines oil-shale program now under way at Rifle, Colo., was begun in July 1944 under the provisions of the Synthetic Liquid Fuels Act, which was passed in the spring of that year under the sponsorship of Senator Joseph C. O'Ma-honey of Wyoming and Congressman Jennings Randolph of West Virginia, aided by Michael W. Straus, former Assistant Secretary of the Interior, and others. The oil-shale plant is only a part of the Office of Synthetic Liquid Fuels, Bureau of Mines, which has under way projects to develop synthetic liquid fuels from coal and other solid materials at Pittsburgh and Bruceton, Pa., Morgantown, W. Va., Louisiana, Mo., as well as the Petroleum and Oil-Shale Experiment Station at Laramie, Wyo., and the oil-shale demonstration plant at Rifle. The oil-shale program is entirely experimental. It is not intended that oil will be produced in great quantities. Production will be limited to the volume obtained from plant-scale experimental operations, which will be kept to the minimum size needed to develop techniques and processes and to demonstrate costs. After the passage of the enabling act in the summer of 1944 a survey of the oil-shale resources of the Nation was made to determine the most suitable general area in which to establish the demonstration plant. The most suitable area was found to be in the Rifle-De Bequearea in Garfield County, western Colorado. Bureau of Mines field parties covered this entire area thoroughly

Jan 1, 1949

By T. Egleston

THE ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, how¬ever, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattle-snake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings ; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

Jan 1, 1875

By R. L. Bleifuss

Most pellets swell only slightly during reduction, but some swell so enormusly that their increase in size is termed catastrophic. Since catastrophic swelling produces irregularities in blast furnace operation, an understanding of the phenomenon is of practical as well as theoretical interest. Observations have shown that catastrophic swelling is characterized by the growth of a network of fine iron filaments. Evidence is presented to show that the growth of these filaments is promoted by the presence of calcium in the magnetite lattice of the original ore. During reduction, the limited mutual solubility of CaO and FeO produces an unstable condition that inhibits the uniform nucleation of metallic iron. Other elements in the magnetite lattice whose oxides are continuously soluble in FeO in the critical temperature range have no effect. Magmatic segregation or pyrometasomatic replacements are the most likely deposits to contain calciferous magnetite. Over the past few years there has been an increasing concern throughout the iron and steel industry over the tendency of pellets to swell during reduction. Although the tendency for swelling is only one of several attributes that determine the behavior of pellets in the blast furnace, swelling-reduction tests are now part of the normal evaluation procedure of many pellet consumers. During a swelling-reduction test, pellets display either the moderate increase in size known as normal swelling, or the enormous expansion known as catastrophic swelling. This paper is concerned with the origin and control of catastrophic swelling and how it is enhanced or inhibited by the presence of minor elements. Swelling Behavior The swelling behavior of pellets during reduction is indicated in Fig. 1. The lower curve represents normal swelling and the upper curve catastrophic swelling.' During the initial stages of reduction, that is, up to about 20-25% reduction, the two curves are considered to be equivalent. Beyond this point normal pellets undergo a gradual decrease in size with increased reduction. By contrast, pellets which exhibit catastrophic swelling show a second dramatic expansion between 25 and 70% reduction. The initial normal swelling develops as the hematite of the pellet is successively reduced to magnetite, and then to wustite. Work by Edstrom' and others has shown that the reduction of hematite to magnetite is accompanied by a 25% volume increase, whereas the magnetite to wustite stage shows a volume decrease. The volume increase overlaps the wustite field because magnetite is formed simultaneously with the wustite during topochemical reduction of the pellet. The catastrophic expansion is clearly related to the wustite, to

Jan 1, 1971

By Thomas Egleston

The ores of mercury of North California are composed of metallic mercury and cinnabar. They are found in serpentine, and are very often associated with chalcedony, in masses more or less irregular, often concentrated enough, however, to furnish ores yielding from three to ten per cent., and sometimes richer. This deposit makes its appearance in Vallejo where it has been worked. North of here the mines are more developed. Most of the quicksilver mines, however, are situated in Sonoma and Napa Counties. On its outcrop the serpentine rocks have become decomposed, and have often been washed away to a considerable depth, so that in many cases in their neighborhood, what is apparently nothing but ordinary dirt, will frequently contain from two to three per cent. of metallic mercury, with but a trace of cinnabar, in which case, as at the Sonoma mine, it is made up into adobes and distilled. Such material does not require to be mixed with dirt to be made into adobes. Very often, also, the outcrop of the rock, where it is not decomposed, is filled with metallic mercury, so that by striking a pick into it, as at the Rattlesnake mine, a pound or more of mercury at a time will sometimes spurt out. Such rock as this is found in several localities in every stage of impregnation, and usually makes very rich ore. There is generally, however, very little of it, and it is found only in the first workings; the ore in depth is always cinnabar. At the Rattlesnake mine near Pine Flat, where large quantities of metallic mercury are found, the rock contains so much petroleum that it has been necessary to make special arrangements to burn the carbides of hydrogen, since the distillation of the petroleum causes an extra quantity of poor soot to be formed in the condensation-chambers. At the Geysers the ore is associated with large quantities of sulphur and gypsum, so that in a hand specimen there is often more sulphur than cinnabar, which is a serious impediment to working, especially for the modern style of furnace with iron condensers, and causes so much soot to be formed that it has been known to penetrate as far as the blower, and to so completely clog it as to prevent its revolution. The ore coming from the mine is more or less hand-picked. In one or two cases attempts have been made to treat the poorest, and especially the very fine ores, mechanically as at the California works.

By M. C. Leverett, S. E. Buckley

The production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. Introduction Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,l and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. Role of Dissolved Gas When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually. contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1942

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By W. Tempelaar Lietz

The Ten Section oil field is located in the San Joaquin Valley in Kern County, California. about 12 miles southwest of Bakersfield in Township 30 South, Ranges 25 and 26 East. The accumulation is in a low relief anticlinal dome and has a productive area of approximately 2,200 acres. Discovered in 1936 as a result of seismic work, it was the first field on the floor of the Valley to obtain production. It had a small primary gas cap, and since its inception has been produced by depletion with controlled withdrawal from the gas cap to minimize blowthrough. STRUCTURE AND STRATIGRAPHY The Ten Section structure is an elongated anticlinal dome with flank dips of only about 7 degrees. A map of the field, now fully developed, and a composite log are shown in Figs. 1 and 2. Contours shown on the map are on the top of the first zone, or Marker XA as indicated on the composite log. As shown, the field has a productive closure of only some 350 feet, and there apparently is no faulting in the reservoir. The productive measures in Ten Section are of Upper Miocene age and are known as the Stevens sand. They contain thin, irregular shale or siltstone streaks which vary considerably in stratigraphic position and thickness and apparently are rather discontinuous. As a result, individual sands and shales cannot be correlated over any appreciable area, which makes it difficult to subdivide the sand body into separate zones which are distinct throughout the field. However, there are two fairly persistent siltstone bodies that at the time of development were considered to divide the productive measures into three - zones. The first, or uppermost zone is productive over the entire field and has an average thickness of 180 feet, of which some 65 per cent is sand. It had a primary. gas cap in the crestal area with an areal extent of 930 acres. The second zone has a productive area somewhat smaller than the first zone, but it did not have any original gas cap. It has an average thickness of about 360 feet, of which 55 per cent is sand. The third zone has a very limited areal extent and a maximum productive thickness of 100 feet, of which 80 per cent is sand. Recently, a deeper oil accumulation, termed the "53" sand, was discovered, but it is not discussed in this analysis. In the first and second zones the water table was at 7,980 feet subsea, while in the third zone it was at 8,080 feet subsea. RESERVOIR CHARACTERISTICS Sand Characteristics The Stevens sand in Ten Section is hard and well consolidated, and numerous wells were cored for core analysis. Core data on four representative wells are shown, plotted beside the electric logs in Figs. 3 to 6. The average porosity is 20 per cent, with porosities ranging from 15 to 30 per cent. It is estimated, from cores taken with oil base muds, that the interstitial water content is about 40 per cent. The average weighted permeability is approximately 140, with measured permeabilities ranging from 10 to 3,000 md. As might be expected with practically no correlation of individual sand

Jan 1, 1949

By J. T. McGrath, G. B. Craig

Tensile tests on aluminum single crystals, grown from the melt, revealed that the yield stress of these crystals was raised as the amount of striation substructure was increased. The number of striation-type boundaries was varied by changing the rate of growth of the crystals. The results are interpreted in terns of a blockage of dislocation movement by striation boundaries. IMPERFECTIONS are known to have a large effect on the mechanical properties of metals. Teghtsoonian and Chalmers 1 studied a block or striation-type substructure in tin and found that the formation of the striations depended upon rate of crystal growth and orientation. They found that the angular misorienta-tion between neighboring striations varied between 15 min and 5 deg. Atwater and chalmers2 investigated striations in tin and lead, and found that purity was another factor which influenced their formation. There was a limiting purity above which the striations were straight and regular. There is little information in the literature concerning how substructures in melt-grown crystals affect strength. washburn3 introduced small-angle boundaries into zinc by a shear process and found a subsequent increase in yield stress which he attributed to the presence of these boundaries. Lauriente and pond4 found the critical resolved shear stress in aluminium crystals grown from the melt, to increase with etch pit density. The etch pits were used as an indication of growth imperfections. In Hibbard's5 work on lineage structure in copper crystals grown from the melt, he tested one crystal containing interlineage boundaries, and found a 50 pct increase in the critical resolved shear stress. Fleischer and Chalmers6, in a recent paper, mention briefly that, in the production of aluminium crystals from the melt when the growth rate was raised from 1.2 to 18 cm per hr, the yield stress increased 50 pct. They felt that the increase in yield stress with rate of growth might be attributed to a higher concentration of impurities in the gage length and also might be affected by the increased number of small-angle boundaries (striations). The present investigation was undertaken to determine the effect of the striation substructure on the strength of aluminum single crystals. EXPERIMENTAL PROCEDURE Aluminum single crystals of 99.9992 purity were grown from the melt using a technique described by Chalmers.7 The growth rate was varied from 0.6 to 20 mm per min, thus producing crystals with varying numbers of striation boundaries. To avoid prior deformation, the crystals were chemically cut to the desired length with a saturated solution of cupric chloride. They were then annealed at 580°C for 24 hr and allowed to cool slowly in the furnace. Finally, the specimens were electropolished using an electrolyte of 5 parts ethyl alcohol and 1 part perchloric acid. Each specimen was approximately 5 in. in length and 0.125 sq in. in cross section. The average orientations of the 5 series of crystals studied are shown on the stereographic projection of Fig. 1. The crystals were strained approximately 2 pct in a soft tensile machine. The strain sensitivity was 3.6 x 10-4 cm over a 5-cm gage length.

Jan 1, 1960

By S. E. Buckley, M. C. Leverett

THE production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. INTRODUCTION Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,1 and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. ROLE OF DISSOLVED GAS When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1941

By Whitman E. Brown, Louis J. Erck

The installation in 1948 of a Hum-phrey~ spiral concentrator section at the Hill-Trumbull plant of The Cleve-land-Cliffs Iron Co. is the latest commercial method on the Mesabi Range being used for the recovery of fine iron ore. In two stages of concentration 84 spirals treat approximately 120 long tons per hour of minus ? in. ore. These spirals augment the production of the heavy-density plant which recovers the plus 36 in. iron from the plant crude ore. Structure of the ore is such that, when crushed, about 50 pct of the plant crude is minus ? in. size. After de-sliming in a 66 in. Akins classifier, grinding the classifier product in a ball mill and again desliming in a 78 in. Akins classifier about 15 pct of the crude ore remains to be treated in the spiral plant. Overall recovery of the ball mill feed in the Hill-Trumbull spiral plant during the 1948 season was about 53 pct of the weight and 66 pct of the total iron content. Of the actual feed delivered to the spirals from the 78 in. classifier 64.9 pct of the weight was recovered containing 73.7 pct of the total iron. The average analysis of the spiral concentrate is 55.05 pct Fe and 14.83 pct SiO2. An average of mill assays during the 1948 season is given in Table 1. The Hill-Trumbull plants treat both wash ore and jig-type ore. During the 1948 season spirals were used only on the fine sizes of jig-type ore. At times the deslimed minus ? in. size is of sufficient grade to warrant bypassing the spirals but in the main the fine size is delivered to the 48 first stage spirals and thence to the 36 cleaner or second stage spirals. In the past several years numerous Mesabi Range ores in the fine size cate- gory have been tested by a wide variety of beneficiating equipment. The prodigious amount of research devoted to the recovery of values in the fine ore reflects the dire need of the iron industry to squeeze the last possible unit of iron from the mined ore and to develop suitable equipment and processes to satisfactorily concentrate the leaner horizons as they are encountered in the process of mining. Large governmental and private appropriations have been allotted, new laboratories built, research and technical staffs increased, and operator-manufacturer cooperative agreements applied to hasten the solution of the problem. The University of Minnesota, at its Eighth Annual Mining Symposium in January 1947, dedicated as its objective the bringing to light of technological developments in iron ore beneficiation. Papers were given at that time relating to processes being developed. Specifically, these papers reviewed flotation, Baum jig, selective media concentrator, Hardinge concentrator, Dorrco sizer, heavy media concentration, Hydrotator, and the Humphreys spiral. The Cleveland-Cliffs Iron Co., after encouraging results from tests in a small pilot plant using one full size spiral, made the first commercial installation of Humphreys spirals on the Mesabi Range at their Hill-Trumbull mine, Taconite, Minn. This company

Jan 1, 1950

By S. E. Buckley, M. C. Leverett

The production of oil is accomplished as a result of its displacement from the reservoir by either gas or water, and the amount of oil recovery is limited by the extent to which the displacing gas or water accumulates. This paper describes the mechanism by which the displacement is effected and the advantages of water over gas as a displacing agent. In the light of the results of experimental observations of the flow of mixtures of oil and/or gas and/or water through sands, certain conclusions are drawn relative to the changing character of the displacement as depletion proceeds, and on the effects of the properties of the fluids and of producing conditions on the ultimate oil recovery. Introduction Crude oil has no inherent ability to expel itself from the pores of the reservoir rocks in which it is found; rather, it must be forcibly ejected or displaced by the accumulation of other fluids. Accordingly, a knowledge of the mechanism by which one fluid is displaced by another is essential to an understanding of the fundamental process by which oil is recovered. The displacing fluids normally available are gas and water, either or both of which may exist originally associated with the oil in a potentially usable form or may be supplied to the reservoir from external sources. Gas is present in most oil reservoirs. If the quantity is relatively small, it may exist originally completely dissolved in the oil, but if the quantity exceeds that which may be held in solution by the oil at the prevailing pressure, the excess will be found in the free state. Most reservoir sands appear to contain some water,l and in the majority of fields the oil is trapped in the structure and held over water. In certain conditions the entrapping water may advance into the oil zone and displace the oil therefrom. This paper describes in a qualitative manner some of the characteristics of the displacement of oil by either gas or water, with an attempt to elucidate somewhat the mechanism by which such displacement is effected. Role of Dissolved Gas When the pressure on an oil containing dissolved gas is reduced to the saturation or bubble-point pressure, gas escapes from solution and expands, imparting to the oil-gas mixture a high degree of expansibility and causing it to flow in the direction of reduced pressure. This expansibility has frequently been attributed to the oil; closer analysis, however, reveals that as gas escapes from solution the oil phase actually. contracts. Hence, it is the accumulation and expansion of the liberated gas that supplies the propelling force for the oil. It has been shown experimentally2-5 that within certain limits a sand containing oil, gas and water will permit the simultaneous flow of all three; the readiness with which they may flow depends upon the characteristics of the sand, of each of the fluids, and upon the relative amounts of the fluids in the sand. Thus, in the initial stages of production by the mechanism of dissolved gas drive, the liberated gas is present in the sand in low concentration and is unable to

Jan 1, 1942

By J.B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By J. B. Pullen

The United Verde mine is in the north central part of Arizona, on the northeasterly slope of the Black Hills, near the town of Jerome. Ore was first discovered in the district about 1875, and the first mining claims were located by M. A. Ruff-ner and associates in 1877. In 1888 the late Scnator William A. Clark secured control of the property and under his ownership it developed into one of the country's most important copper producers. The property was sold to the Phelps Dodge Corporation in 1935, and since then has been under this Corporation's management. Except for shutdowns caused by general world-market conditions, production has been continuous from 1890 to date. Geology The mineralized zone ranges in area from approximately 12 acres to less than 5 acres. All mineralization occurs in the pre--Cam-brian intrusives. The first intrusion, according to geologic records, was the quartz porphyry, which later was intruded by augite diorite. Following the diorite intrusion through a series of intrusions of lesser magnitude, a pipelike mass of massive sulphide, quartz and rock was formed. The diorite forms the hanging wall of this mass, and the porphyry the footwall. Between the footwall and the sulphide a band of chlorite schist was formed, probably owing to metamorphic conditions. Commercial ore occurs along the contact of the schist and sulphide extending into the sulphide, sometimes entirely through the schist, and fingering out into the porphyry. The ore deposit was formed by replacement similar to deposits formed in limestone areas. Faulting and deformation occurred in pre-Cambrian times and again in the Tertiary period, removing approximately 2000 ft. from the top of the main United Verde ore body, forming the United Verde Extension ore body, the only other major ore body in the district. Major development work has shown that the sulphide mass extends to the 3300-it. level, and diamond drilling below this level has indicated that the mass might extend below the 3700-ft. level, but in a diminished quantity. While many copper minerals exist in the mine, the chief commercial mineral is chalcopyrite. Aplan and vertical section of the mineralized zone showing the principal geological eatures is shown in Figs. I and 2. General Description and Physical Condition or Mine After over 50 years of active production, ore still exists on almost every level of the mine. This condition is due to many causes —-mine fires, which broke out as early as 1894, caused the abandonment of certain areas; subsidence and ground movements retarded the cleaning up of others. Furthermore, in the early days there was such an abundance of ore that when mining became dificult it was a simple matter to replace the production by going to a deeper level. Several attempts were made to recover the ore in the fire zone, both by glory-holing

Jan 1, 1943

By H. A. Wriedt

At 500°C (932°F) the range of y' iron nitride is from 5. 77 + 0.03 wt pct N (in coexistence with a iron) to 5.88 * 0.03 wt pct N (in coexistence with E iron nitride). Stoichiometric "Fe,N" (5.900 wt pct N) is near the upper extreme of possible compositiom. The depe-dence of nitrogen activity (expressed as pnh,/Ph,) on nitrogen content is described satisfactorily by a "Langmuir" isotherm: At even the highest nitrogen concentrations, less than 0.18 pct of' the nitrogen atoms present are impositions of disorder. Past investigations1-4 of the Fe-N system have left only details of the thermodynamic behavior of the y' nitride, "Fe,N9', to be studied. The present investigation was made to establish more precisely than hitherto the limits of composition and the relation between composition and nitrogen activity at 500°C. EXPERIMENTAL TECHNIQUE The compositions of nitrides in equilibrium with various NH, + Hz mixtures at 500°C were determined from the weights gained by 0.02-in.-thick (4.0 to 4.5 g) strips of purified iron* when the nitrides were formed A description of the gas generation and furnace system has been published.5 Cracking and blistering during conversion of the original solid iron at 550°C injected considerable porosity into the strips without causing their disintegration. The time for complete conversion was significantly lowered by periodically reducing partly nitrided specimens in hydrogen and then reexposing them to the nitriding gas. Gas mixtures producing single-phase were used in the equilibrations at 500°C. Equilibrium was regarded as existing when the specimen weight was not detect-ably affected by further exposure to the same conditions. The gas compositions and nitrogen activities at which y' transformed to a iron (lower activity limit) and to E iron nitride (upper activity limit) were redetermined during the investigation. A specimen was equilibrated in an NH, + Hz mixture at 500°C and then exposed to a s1ightly different gas. When equi- librium had been reestablished the gas was again changed slightly. At each stage of this repeated process, while the specimen was reacting with the gas, the variation of its weight with time was observed. The onset of phase transition was marked by an abrupt change in the amount and rate of weight gain or loss. The specimens were weighed outside the furnace, in air and at room temperature, on a balance with 0.05 mg precision. When it was found that the specimens were oxidizing at a significant rate during the weighing, a series of timed weighings was made with each specimen, starting 1 min after its exposure to air. RESULTS AND ANALYSIS The gain in specimen weight from oxidation during weighing was linear in the logarithm of time between 1 min and about 2 hr, Fig. 1, later becoming linear in the cube root of time. In the logarithmic period, nitride specimens oxidized two to three times as fast as

Jan 1, 1970

By Nicholas J. Grant, W. Michael Yim

The creep-rupture properties of nickel, in as-prestrained or prestrain-polygonized condition, were studied at 1300°F and 4000 psi, and also at 700°F and 26,000 psi. An improvement of strength was noted in both the as -prestrained and the prestrain-polygonized tests at each temperature. The as-prestrained tests, however, showed superior creep resistance to the prestrain-polygonized ones. From the results of X-ray and etch-pit studies, the strengthc gain was interpreted in terms of dislocation density and the stability of preformed substructures. COLD work is known to improve the strength properties of metals at low temperatures. At high temperatures, however, the strength improvement is often lost if gross structural changes, such as re-crystallization, take place prior to or during the test. Even in the absence of recrystallization, a prestrained metal may undergo structural changes— polygonization and the formation of well-defined subgrains—which importantly effect the resultant properties. The relationship between substructure and creep properties has received considerable attention in recent years. The work of wood1 indicated that the creep strength of aluminum and its alloys was closely related to the subgrain size. Hazlett and Hansen,2 and Ancker, Hazlett, and parker,3 working with nickel and nickel alloys, had shown that small amounts of prestrain at room temperature followed by a recovery anneal at 800°C (1470°F) improved the strength at both low and high temperatures. The strength gain was attributed to an increase in the number of subgrain boundaries as a result of the prestrain-polygonization treatment. More recently Coldren and Freeman4 studied the effect of substructures on the creep rate of nickel at 1550°F. Their conclusions indicated that the substructure size as measured by the number of boundaries was the factor that controlled the creep rate. In addition, the perfection of the subgrain boundary has been indicated to have an important role on the strength.' On the other hand, there are data which disagree with the above observations. Grant, Chaudhuri, Silver, and Ganow6 found no creep strength improvement by a prestraining treatment. In reviewing the role of subgrains on high-temperature creep, Shepard and Dorn7 concluded that the contribution of the subgrains to high-temperature creep strength was a minor one. Guard,8 in a recent study on poly-gonized nickel, has cast doubt on the validity of the postulate that subgrain size controls the creep rate. In the majority of the previous studies, the subgrain boundaries have been singled out as the most important factor in determining creep strength; however, there is no firm theoretical ground for the postulate that the subgrain boundaries act as effective barriers to dislocation motion.B910 Little effort has been directed toward the study of the relationship between creep strength and other structural variables, such as dislocation density, lattice strain,

Jan 1, 1963

By R. C. Mahon

The Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. Surface Water Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1946

By A. W. Demmler

RECENTLY, Chaudron,&apos; Montariol,2 and their co-workers published the results of their studies on zone-refined aluminum. They found their material to be capable of recrystallization at —50°C, but gave no data as to the percentage reduction or time required. Their material was found to be practically non-work hardening at room temperature, but after 96 pct cold work at a low temperature and storage in liquid nitrogen it was found to recrystallize to coarse grains in less than 3 hr at 20°C. Recently, a study was made of the room temperature recrystallization characteristics of zone-melted aluminum. An ingot 14 in. in length, with a 3hx3 in. cross section, was made in an extremely high purity graphite boat under an atmosphere of dried commercial argon. It was made by first passing the molten zone along the ingot of 99.99+ pct A1 15 times. At this point, the most impure 3 in. (the end toward which the eutectic forming impurities migrated) were replaced with more of the original starting material, and 15 more traverses were made. Each traverse of the zone along the ingot required approximately 3 hr. Three ingots were prepared in this identical fashion and the chemical analyses were made spec-trographically on two of these ingots, rather than on the one used in this investigation. The analyses were made at 1 in. intervals along the ingot, in duplicate. Over the purest 5 in. of the ingot, which were most important in this investigation, there was found an average composition of <0.00004 pct Cu, <0.0003 pct Fe, <0.0001 pct Si, and <0.0001 pct Mg. In addition, the following elements were not detected spectrographically even in the more impure end of the bar: manganese, zinc, nickel, chromium, titanium, vanadium, lead, tin, boron, beryllium, bismuth, gallium, zirconium, cadmium, antimony, cobalt, and molybdenum. The original ingot was given several cold reductions, with intermediate anneals in order to refine the grains. Owing to the extreme length resulting and the ease of deforming the material plastically, it was cut into eight equal lengths and identified as shown in Fig. 1, with the highest numbered section at the purer end (that enriched with peritectic formers). Section 6 was used in the exploratory work and was found to be of exceptionally high purity, giving more rapid rates of room temperature re crystallization than any previous aluminum studied at the Alcoa Research Laboratories. This fact suggested that the entire midsection of the ingot might be of very high purity. Accordingly, section 4 was chosen for the next study. A portion of it was rolled to cold reductions of 10, 25, 40, 60, 75, and 90 pct at room temperature, and the re-crystallization of each specimen was followed by X-ray pinhole transmission photographs. The other portion received the same treatment, except that both the specimens and the rolls were maintained at 160°F in the process of rolling. The latter ortion was retarded in its recrystallization as compared to the former, probably due to the stress relief effect of the warm rolling. Both of these portions of the fourth section were found to recrystallize at a considerably slower rate than did the sixth section.

Jan 1, 1957