Search Documents

Jan 1, 1920

By T. E. Leontis

Data are presented in this paper to show that addition of zirconium to sand-cast Mg-Th alloys effects a marked decrease in the grain size of these alloys which is accompanied by a significant increase in the mechanical properties over the entire range of thorium content investigated. The beneficial effect of zirconium on the strength properties is maintained at elevated temperatures up to 700°F. In addition the alloys exhibit exceptionally high creep resistance at temperatures up to 600°F. Zirconium does not greatly improve the strength or creep characteristics of extruded Mg-'Th alloys. Cerium is not a desirable addition to Mg-Th-Zr alloys. IN a previous paper,' it was shown that addition of thorium to magnesium imparts exceptionally high resistance to creep at elevated temperatures both in the sand-cast and in the extruded states. The large grain size of the sand-cast alloys, however, renders them of questionable value as engineering materials. Sauerwald² showed that the grain size can be reduced effectively by the addition of zirconium. Results of a detailed study of the properties of Mg-Th-Zr alloys over a wide range of thorium content are presented in this paper. In accordance with the preliminary findings of Sauerwald,² it is shown here that Mg-Th-Zr alloys possess the unusual combination of fine grain size and a high level of strength and creep resistance at elevated temperatures. Some information on the effect of cerium on the properties of Mg-Th-Zr alloys is presented also. Effect of Th on Solubility of Zr in Molten Mg Sand-cast test bars and 3 in. diam extrusion billets of Mg-Th-Zr and Mg-Th-Ce-Zr alloys* were pre- pared according to the procedures described in the previous paper.' The zirconium was added in the form of sponge metal as supplied by the Bureau of Mines.' The maximum amount of zirconium that usually can be introduced into magnesium at the customary alloying temperature of 1350° F is about 0.7 pct. The analyses in Table I clearly show that thorium in- creases the solubility of zirconium in liquid magnesium. The tabulated zirconium contents are designated as "acid soluble;" this serves to distinguish these values from the small amount of zirconium that is not dissolved when the alloy is subjected to the action of a dilute acid solution. The "acid-insoluble" zirconium is believed to be ineffective as an alloying ingredient. The acid-insoluble zirconium contents ranged between 0.03 and 0.16 pct in the present alloys, the tendency was toward higher values in alloys with higher thorium content. In contrast to the effect of thorium, cerium decreases the solubility of zirconium in magnesium. This is shown by the three Mg-Th-Ce-Zr alloyst in- cluded in Table I and stands in agreement with the observations of Nelson and Stricter".' on Mg-misch-metal-Zr alloys. Effect of Zr on Grain Size of Mg-Th Alloys The potent effect of zirconium as a grain refiner has been demonstrated for many types of magnesium alloys.3-8 Of greatest importance to date are Mg-Zn-Zr alloys5,6,8 and Mg-mischmetal-Zr alloys.3,4,7 Zirconium has also been found to exert a marked grain-refining action on Mg-Th alloys. All the Mg-Th-Zr alloys cast in the form of ½ in. diam test bars have an exceedingly fine grain size (Table I). Reference to the previous paper' will show that binary Mg-Th alloys containing up to 6 pct Th are almost completely columnar even in the M in. diam reduced section of a test bar, and that 10 to 50 pct Th alloys have an equiaxed grain structure of 0.03 to 0.08 in. The data in Table I also show that addition of cerium to Mg-Th-Zr alloys has no effect on the grain size. In addition to increasing the strength properties, the fine grain size of Mg-Th-Zr alloys

Jan 1, 1953

By William Y. Holland, Roger M. Cook

In view of the increasingly widespread deterioration of concrete structures as the result of the interaction of the alkalies sodium and potassium released by hydration of portland cement and susceptible rocks and minerals in aggregates, it is believed that a paper summarizing the geographic distribution of these aggregates will be of interest to producers and users of concrete, concrete products, and concrete-making materials. THIS paper reviews the problem of alkali-aggre-gate reaction in concrete and describes the geologic and geographic occurrence and distribution of alkali-reactive sand and gravel in western United States. It includes no discussion of crushed stone or synthetic aggregates. Most deposits of sand and gravel are accumulations of particles of rocks and minerals from a variety of sources, and it is not unusual for at least one or two varieties of the rocks to contain some form of reactive material. Examination by petro-graphic methods of many sands and gravels, as well as manufactured aggregates, has shown that a comparatively high proportion of the deposits does contain, in greater or lesser degree, rocks and minerals known to be deleteriously reactive with the alkalies of cement. Fortunately the amount of reactive materials is commonly less than that necessary to cause deleterious effects in concrete. As investigation of unsound concrete structures progresses, it becomes evident that the alkali-aggre-gate reaction is even more widespread than supposed, Figs. 1 and 2. Even though some parts of the country appear at present to be immune, further investigations will probably show that the effects of alkali-aggregate reaction can be seen in many structures in these areas, although only on a small scale in most of them. Many concrete structures will, of course, have lived their useful life before disintegration from this cause is serious, and in others the alkali-aggregate reaction may never become significant even though the microscopic evidence of reaction is present. The alkali-aggregate reaction first was reported to be a cause of deterioration of concrete in 1940 when Stanton1 described expansion of concrete pavements in California. Similar expansion and deterioration of concrete was recognized during succeeding years in concrete structures located in many parts of the country, but particularly in the western states. A number of concrete laboratories2 became interested in the problem. It was soon determined that only certain combinations of aggregate and cement caused the alkali-aggregate reaction to take place, and moreover that the reaction progresses only in the presence of water. Further research proved that cements containing more than 0.60 pct total alkalies (pct Na,O + 0.658 x pct K2O), when used with aggregates containing appreciable amounts of reactive ingredients, caused the reaction to take place, usually with subsequent deterioration of the concrete. During the last few years this limitation has been adhered to in both government and private construction as the maximum allowable alkali content of cement to be used with aggregates of known alkali reactivity. Because of this limitation, it appears that deleterious reaction either has been reduced or eliminated in many recently built structures in which it probably would otherwise have occurred. Recent tests have shown that the degree of expansion obtained with any particular cement-aggre-gate combination depends not only on the alkali content of the cement but also upon the relation of this alkali content to the amount and degree of reactivity of reactive constituents in the aggregate.' In laboratory mortar bars, opal and cements with alkali content of as low as 0.2 pct (as equivalent of Na2O) have produced deleterious expansion as the result of alkali-aggregate reaction. These experiments demonstrate that aggregates containing even 0.1 pct of opal are deleteriously reactive. It was soon determined that alkali-silica gels were formed by the interaction of the alkalies of the cement and the reactive aggregate, Figs. 3 and 4. Osmotic or swelling pressures produced by the continued hydration of these gels cause expansion of the concrete with resulting cracking, warping, and dislocation. Evidence of the alkali-aggregate reaction can be seen by a petrographic study of the deteriorated concrete. Among the first structures studied by this method was Parker Dam on the Colorado River, California-Arizona. In the concrete from this dam pebbles of rhyolite, andesite, siliceous limestone, and chalcedonic chert were found to be reactive.

Jan 1, 1954

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

By R. E. Zimmerman, Michael Sokaski, E. R. Palowitch, M. R. Geer, H. F. Yancey, W. Deurbrouck, S. C. Sun

PART 1: DENSE MEDIUM SEPARATION by M. SOKASKI, M. R. GEER and H. F. YANCEY INTRODUCTION In the early days of coarse-coal treatment by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken :he loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War 11 in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-ton-per-hour pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London. In April 1945,2 operation of this pilot plant was observed by one of the authors, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was started by the Bureau of Mines immediately. This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals was made available. Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are so easy to clean they respond well to simpler cleaning systems, the first cyclone plant was not built until 1961.3 As of the spring of 1967, a total of 31 commercial cy- clone plants had been installed or were under construction in the United States; this does not include eight Dynawhirlpool plants. The capacity of the cyclone plants ranges from 50 to 1300 tons per hour and totals 6600. THEORY Before discussing the theory of a dense medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in figure 10-1, the mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vertical flow. The refuse moves along the wall of the cyclone and is discharged through the under- flow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the vortex finder to the overflow chamber.

Jan 1, 1968

By Paul A. Taylor

MUCH information concerning pegmatites which was thought to be true a few years ago has been proved false, and what is now actually known about some pegmatites is not true of many others. The erratic and seemingly unpredictable structure and variable composition of this class of mineral deposits has been widely emphasized. Even parts of the same pegmatite body exhibit marked differences in texture, mineral composition, width, and attitude. Constructive geological thinking in respect to pegmatites now aims to establish general laws rather than to stress the confusing diversity of features having no special economic significance. Substantial progress has been made in classifying different types of these deposits according to general features, internal structure, mineralogy, and origin. In some cases it has even been possible to block out tonnage reserves in advance of mining. It is still easy, however, to make highly erroneous predictions after a preliminary examination of a pegmatite prospect. Pegmatites are important to the economic well being of the country and to its military security. They furnish virtually all the feldspar, strategic mica, beryl, columbium, tantalum, and caesium utilized in the United States, as well as sundry other minerals and significant amounts of lithium and rare earth minerals and gems. With the exception of vermiculite, occasional ilmenite-rutile, and perhaps soda-lime feldspar and garnet deposits, basic pegmatites are of little economic importance. Consequently in this paper, as in common parlance, the term pegmatite generally relates to coarsegrained acidic rocks or what is aptly called giant granite. Available data indicating the size and importance of the production and trade in specified pegmatite minerals are summarized in Table I. Geological Features Much of the latest thinking on the economic geology of pegmatites is now available in a 115-page monograph' by a group of experts who participated with geologists of the Federal Geological Survey in the widespread wartime investigations. Doubtless the most significant feature of the monograph is indicated by the title, The Internal Structure of Pegmatites, but it also contains a vast amount of other new information and includes the assimilated concepts of many earlier writers, whose works are given in a comprehensive list of references. The shape, size, attitude, and continuity of many pegmatite bodies is controlled by the structure of the older rocks in which they occur. If the older rocks are easily penetrated, e.g., biotite schist, most of the pegmatites in a given district will be found outside the parent granite mass as exterior pegmatites. Marginal pegmatites are more prevalent if the older rocks are massive, unsheared, and sparingly jointed. Networks of pegmatites are abundant in highly-jointed rocks. In strongly foliated schists the bodies are usually lenticular, whereas in highly-folded areas they assume tear drop, pipe or pod-like, bow-shaped, or sinuous forms. Jahns2 recognizes five major shape classes: l—dikes, sills, pipes, and elongate pods; 2— dikes, sills, pipes, and pods with bends, protuberances, or other irregularities; 3-—trough-or scoop-shaped bodies with or without complicating branches; 4—bodies with the form of an inverted trough or scoop; and 5—other bodies, including combinations of the above and miscellaneous shapes. Many pegmatite deposits are scarcely big enough to be recognizable as such. Most of them, in fact, are small tabular deposits less than 4 in. wide and usually without economic concentrations of minerals. On the other hand, some pegmatites are more than a mile long and over 500 ft wide. The ratios of length to breadth range from 1 : 1 to 1 : 100. Although the vertical dimension bears no invariable relationship to strike length, tabular deposits or large lenses are often symmetrical enough to show nearly as much continuity down dip as in their horizontal extension, and some pipes or pods are amazingly persistent in the vertical plane. Small pegmatites often string along a fairly definite trend line; in a given district major bodies may lie roughly parallel, and where only a few of them do not, the erratically disposed bodies generally differ in composition from those conforming to the regular pattern. This does not apply, however, in all districts. Characteristically, pegmatite veins pinch and swell or split into branches. When they pinch out entirely it is often possible to find a new body by prospecting the extension of the strike or dip, but the chances of finding a hidden deposit are ordinarily too uncertain to justify much subsurface prospecting. Diamond drilling may yield valuable information as to the continuity of known deposits whose upper portions are well-exposed. Some deposits, in fact, can be proved up for hundreds of feet by surface trenching and then intersected by drill holes at various depths like any other vein-like deposit. Others twist and branch, apparently defying all efforts to explore them short of actual mining.

Jan 1, 1954

Jan 1, 1928

By William G. Pariseau, H. Douglas Dahl

Recent subsidence legislation indicates that mining engineers would be welt advised to be able to predict and control surface damage caused by mine subsidence. To date, such an ability is practically nonexistent. Model analysis is suggested as one of the alternative paths available which might yield fruitful results. Similitude requirements developed for a self-loaded body in static or quasi-static equilibrium indicate that complete similitude without centrifuging is an impracticability. However, a pilot experimental study which used a simplifying assumption to correctly model mine subsidence has produced results in qualitative agreement with field observations. The purpose of this paper is to present a discussion of the various approaches that can be taken in the study of mine subsidence phenomena. Particular attention is focused upon the rational selection and use of laboratory models. Broadly interpreted, mine subsidence is the deformation of the rock mass enclosing a mine. Depending upon a number of factors, the movement of the subsiding rock mass may disrupt gas and water lines or other buried utilities, damage surface structures such as buildings and bridges, dislocate streams, roads, and rail lines, aggravate acid mine drainage and fire problems, and generally mar the landscape. It is clearly a problem that no mine manager can safely ignore. It is also a problem that will grow with the general population increase. In the following discussion, a summary review of past and present approaches to subsidence studies is given. The possibilities of duplicating subsidence phenomena in laboratory models are examined, and an analysis of a particular type of model is presented. Some preliminary results obtained from a model of the particular type analyzed are then discussed. REVIEW OF PREVIOUS WORK Historically, subsidence investigations have been empirical studies in the field and laboratory or theoretical analyses of mathematically idealized media. Empirical and theoretical work in the United States has generally lagged behind investigations abroad. In the United States, field studies are mostly pre-World War 11. These are summarized in the Mining Engineer's Handbook. ' Field studies in Europe are more recent and more extensive. Those made in Great Britain are summarized in the Subsidence Engineers Handbook2 and represent observations made at 157 different collieries. Such studies by themselves are of limited usefulness as are all empirical studies. One can never be certain that conditions at one mine will be similar enough to those at another to warrant the drawing of like conclusions. European subsidence formulas rely heavily upon the "angle of draw" and "critical area" concepts. The angle of draw is defined as the angle between a vertical line through the face, and another line extending from the face to the surface at the point where movement is zero. The critical area is defined in relation to the least extraction necessary to produce maximum subsidence. Fig. 1 illustrates the angle of draw and critical area concepts. First and second "limits of influence" are also shown. The angle of draw and associated critical area concept are obviously not well defined, being dependent upon the accuracy of the surface survey. In Great Britain, the angle of draw has increased through the years from about 26 to 35°. In the United States, zero and negative angles of draw have been reported. In the authors' opinion, these purely geometrical concepts represent an oversimplification of subsidence phenomena and their use, in the United States at least, should be discouraged. Empirical observations of laboratory models containing layers of earth, sand, clay, and plaster were made by Fayol (cited by Peele) as early as 1885. An outgrowth of his work was the "dome theory," a verbal description of what is assumed to occur in subsiding rock masses. The dome theory has since fallen into disrepute. Theoretical analyses worthy of the name treat a subsiding rock mass as a deformable body. In these analyses, the actual rock mass is replaced by an idealized material that deforms according to a simple stress-strain relationship. The stress equations of equilibrium expressing the Newtonian laws of mechanical action and the geometry of strain furnish additional equations that must be satisfied. A loading criterion-generally understood, and in some cases stated explicitly-completes the theory.

Jan 1, 1969

By David A. Thomas, John F. Peck

Fibrous microstructures and their development have been studied by metallography and by hardness and quantitative metallographic measurements. Thin, curved grains were observed in transverse sections of commercial tungsten wire and were developed in laboratory-drawn iron wire at reductions greater than about 70 pct. The unusual grain shapes are attributed to the nonuniform mode of deformation of the grains associated with the characteristic [I101 preferred orientation that develops in bcc metals during drawing. Transverse sections of heavily swaged iron wire showed a ospiral nebulao structure that appears to result from the elliptical shape of the cross section of the swaging dies and their rotary motion. Hardness and quantitative metallographic results show unusual trends that parallel the changes in microstructure. Other phenomena are considwed in light of the results, including the strength of fine wires of bcc metals, ocylindricalo textures, and the ductility of fibrous tungsten. 1 HE microstructure of tungsten wire in a longitudinal section shows grains highly elongated in the working direction, giving the appearance of a bundle of parallel fibers, Fig. l(a). Wires of tungsten and other bcc metals show a pronounced preferred orientation in which a [I101 direction is parallel to the wire axis.l The microstructure and texture of tungsten develop during warm working (working above room temperature but below the recrystallization temperature) into wire by swaging and drawing. Fibrous tungsten so produced has limited but useful room-temperature ductility, whereas annealed tungsten is brittle at room temperature. During an investigation of the effect of recovery annealing on the substructure of commerical 0.030 in. diam tungsten wire, it was found that transverse sections of the as-received material showed thin, curved grains, Fig. 1(b), instead of the expected equiaxed grains. The fact that Figs. l(a) and (b) show different sections of the same material at the same magnification is at first disconcerting, because the long dimension of the curved grains in the transverse section is several times the average fiber width in the longitudinal section. However, a longitudinal section cuts most of the curved grains across their narrow dimension, giving the appearance of a multitude of narrow fibers. On the other hand, the plane of a longitudinal section occasionally includes a long dimension of a curved grain, resulting in a broad ofibero, such as A in Fig. l(a). EXPERIMENTS AND RESULTS To investigate the origin of fibrous microstructures and particularly the unusual transverse-section structure of tungsten, rods of iron (also bcc) were drawn and swaged in the laboratory. One rod of annealed Ferrovac E was drawn in six steps to a total reduction in area of 87 pct (0.10 to 0.036 in. diam), and a second rod was swaged to the same reduction, using approximately the same reduction steps. Longitudinal and transverse sections of the swaged and drawn iron wires are shown in Fig. 2, for reductions in area of 39, 73, and 87 pct. A fibrous microstructure in longitudinal section is first evident at 73 pct reduction, and it is further developed at 87 pct reduction. The grains in transverse section remain equiaxed until about 73 pct reduction, when they become somewhat elongated and curved. At 87 pct reduction, the drawn wire shows thin, curved grains in the transverse section, similar to those observed in tungsten. The transverse sections of the iron wires swaged 83 and 87 pct reduction in area show the striking ospiral nebulao structure in Fig. 2(d). This struc-

Jan 1, 1962

Institute of Metals Division Ferrous and Nonferrous Physical Metallurgy Established as a Division April 26, 1918 (Bylaws published In the 1944 TRANSACTIONS Volume of the Division) A A SMITH, JR, Chairman E A ANDERSON, Past-Chairman F N RHINES, Senior Vice-Chairman W A DEAN, Vice-Chairman H A MALONEY, Treasurer ERNEST KIRKENDALL, Secretary 29 West 39th Street, New York 18, N Y Executive Committee R M BRICK 2 W A JOHNSON 1 H I DIXON 2 E W PALMER 1 M GENSAMER 2 J H SCAFF 3 J D HANAWALT 1 J D SULLIVAN 3

Jan 1, 1952

Jan 1, 1927

By D. R. Parrish, T. M. Geffen, R. A. Morse, G. W. Haynes

Flow tests on small core plugs have indicated that a large amount of gas is trapped and not recovered by water flooding a gas sand. Instead of I to 15 per cent pore space, as is usually assumed, the residual gas saturation is 15 to 50 per cent pore space, and is thus of the same magnitude as residual oil after water flooding oil sands. A thorough investigation was made to ascertain that large amounts of residual gas actually remain in reservoirs after a water flood and that this condition is not merely a laboratory phenomenon. In field experiments, the amount of gas left in a watered-out gas sand was measured by use of a pressure core barrel and the residual gas saturation of two watered-out gas sands was determined by electric log evaluation. In the laboratory, an investigation was made of factors that could possibly cause the value of residual gas saturation as measured on small core plugs to differ from that in the reservoir, and the effect of these factors on the amount of residual gas saturation was studied. The factors studied include flooding rate, static pressure, temperature, sample size and saturation conditions before flooding All evidence established that a relatively high gas saturation is trapped in water flooded gas sands and that this residual gas saturation can be measured in the laboratory by tests on small core plugs. INTRODUCTION There. has been general agreement among engineers that very high recovery of gas could be obtained from natural reservoirs By water displacement. Gas recoveries of 80 to 95 per cent of the original gas in place have become the normal expectation in water drive fields. The assumption of high recovery has been based on: 1. low density and viscosity of gas compared with water; 2. the erroneous assumption that the flow relationship in a gas-liquid system where gas is the displaced phase will be the same as when it is the displacing phase. It has long been recognized that gas can flow at very low gas saturations (in the range of 1 to 15 per cent pore space) in systems where liquid is being displaced by gas. By assuming the reversibility of this process, the conclusion was reached that the residual gas saturation following water flooding of a gas reservoir would be the qame (1 to 15 per cent) as that at which gas first flowed continuously as a displacing phase. Recent laboratory relative permeability Studies have demonstrated that the flow characteristics are very different in gas-liquid systems, depending on whether gas is displacing or being displaced by, a liquid. Also, it has been shown that there is no difference between the flow characteristics of oil and water or gas and water in water wet porous rocks. The residual gas saturation that can be expected following water flooding of a gas reservoir then would be in the same range as the residual oil saturation normally expected after water flooding an oil reservoir! i.e., in the range of 15 to 50 per cent pore space, depending on the rock characteristics. Obviously, such a difference in residual gas saturation means very important differences in recoverable gas reserves from water drive reservoirs. For example, if the original gas saturation in a field were 70 per cent, and the residual gas following flooding were 35 per cent, only half of the gas in place could be recovered by complete water drive, compared to the previously expected 80 to 95 per cent. This is a situation in which complete pressure maintenance could result in very greatly reduced recovery, since straight pressure depletion recoveries from gas reservoirs can approach 80 to 90 per cent. Such a change in thinking must be based on more complete information than a series of small core tests. Hence the work reported herein was undertaken with the objective of determining whether or not residual gas saturations indicated from small core relative permeability tests at atmospheric pressure and room temperature are representative of the residual gas saturations which could be expected after water flood of natural reservoirs. A study was made both through laboratory and fields tests to determine any differences in residual saturation which might be occasioned by differences in pressure, temperature, rate of flooding, and original saturation conditions. Four separate types of laboratory experiments and two field mesurements were made in this investigation. The apparatus and testing methods of each will he discussed individually. LABORATORY EXPERIMENTS, APPARATUS AND PROCEDURE Relative Permeability Tests Steady state flow experiments Here conducted using the Penn State type apparatus. The equipment used has beer (described in a previous publication? "Irreducible" water satu-ration was established in the core' by imposing ,a capillary pressure of 45 psi before simultaneous flow of air and water

Jan 1, 1952

Jan 1, 1926

By Forrest V. Williams

The dislocatiorl and stacking-fault structuve of epitaxial GaAs1-,PX lms been examined by chemical etching. The layers were groun in the (100) direction and etch Pils were developed on (111} planes which nad been lapped and polished on the epiLaxia1 layevs. Tile effecL of the jollolcing cariables on the quality of the epilaxial layers has been examined: doping leuel, grouth rate, and composition. High stacking-faullL densilies weve found in the GuAsi_xpx layers. These are not observed in heavily dolled epitaxial layers tzar in layers with low phosphorus compositions. The dislocatiorz density in GuAsi-x px was highest at the sub-stvate- epilaxia1 layer interface. Composilion changes introduced dislocations in the epitaxial layers. ManY semiconductor p-n junction lasers of Group TIT-Group V compounds and their alloys have been reported in the past several years. Laser action at visible wavelengths in GaAsl-x,Px was first reported by Holonyak and Bevacqua. GaAs, a direct transition semiconductor which lases, and Gap, an indirect transition semiconductor which does not lase, form a continuous series of solid solutions.2 Laser junctions can be fabricated in GaAsl-xPx crystals with phosphorus compositions up to about 40 mol pct. In addition to the production of coherent radiation in these crystals, the efficient recombination radiation of p-n junctions in this material has equally important potential in the development of low-power semiconductor lamps. To achieve a high conversion efficiency of electrical to optical energy in p-n junctions in this material, the relation of physical properties of the crystal to luminescence efficiency must be better understood. Although the electrical, optical, and device properties of GaAsl -xPx junction lasers are understandably of considerable interest, the work to date indicates that the more serious problems are the chemical and metallurgical difficulties encountered in the growth of this material.3 In addition to the problems of chemical purity, crystal imperfections, such as dislocations and stacking faults, can be expected to affect both the efficiency of the radiative recombination process and the perfection of the p-n junction.3 The last requirement, i.c., that of the perfection of the p-n junction, is a particularly troublesome one in the fabrication of laser diodes. To obtain good laser diodes, the p-n junction must be flat, which permits the radiation to be reflected from the resonant cavity boundaries. Junction planarity is extremely sensitive to the crystal perfection of the semiconductor material. Also, it is known that at high dislocation densities (-105 per sq cm) it has not been possible to build laser junctions in GaAsl-xPx . Few studies have been reported on the crystal defect structure of GaAsl-,P,. The first serious study seems to be that of Wolfe, Nuese, and Holonyak,3 who examined the dislocation structure of monocrystalline bulk (nonepitaxial) material grown by halogen vapor transport. In this paper are reported some observations on the dislocation and stacking-fault structure of GaAsl_,P, crystals grown by a vapor transport process on substrates of GaAs. EXPERIMENTAL Crystal Growth. The GaAsl-xPx crystals were grown in an open-tube flow system, using two sets of reagents. GaAs, Pr(red), and HC1 were employed in one method. The transport reaction is =950JC GaAs+HC1 = GaCl +1/4As4 +1/2H2 and the deposition reaction is 2GaAs1-xPx +GaCl3 Composition control is obtained by the flow rate of the HC1 and the vapor pressure of the P4, which is maintained in a separately controlled furnace. The second method has been described by Ruehr-wein4 and utilizes gallium, AsH3, PH3, and HC1. The same transport and deposition reactions as above are involved. Composition control is obtained solely by the flow rates of the three gases involved. All of the crystals were grown on chemically polished GaAs substrates oriented on the (100) plane. The thicknesses of the epitaxial layers were typically 100 to 300p. Revealing of Dislocations. Dislocations were re-vealed on both the( 111 ) and { l l l }b faces by chemical etching. The specimen to be examined was mounted at 54.7 deg, lapped on glass with 3-p alumina, polished on cloth with 3-p diamond paste, and, to remove work damage, chemically polished at room temperature for

Jan 1, 1968

By C. Cronquist

Since April, 1962, Shell Oil Co. has operated a peripheral line-drive waterflood of the 10.750-ft lower Tuscaloosa (Cretaceous) Denkman sand in the Little Creek field. Located in southwestern Mississippi in the lower Tuscaloosa trend, the field was discovered by Shell in Jan., 1958. Among the largest in the trend, the accumulation is controlled stratigraphically and occurs in an extensive series of alluvial-point bar deposits across a nose that dips gently to the south. The crude oil is 39" API gravity and was highly undersaturated at initial conditions. Early production behavior indicated a depletion drive with slight water influx; primary recovery wm estimated to be 25 million bbl, or 24.5 percent of stock-tank oil originally in place. A.s a result of a favorable mobility ratio and remarkably uniform rock properties, the volumetric sweep eficiency in the waterflood has exceeded 90 percent. Despite the high connate water saturation (56 percent), the displacement efficiency by water injection has been quite efficient, contrary to traditional concepts. Based on observed field flood-out performance, ultimate recovery is calculated to be 46 million bbl. As anticipated, the production rate began declining during 1964 due to a continu ing reducrion in the number of producing wells as flood fronts advanced across the field. Cumulative recovery as of Jan., 1968, was 44.8 million bbl; waterflood operations ~hould be complete by 1970. Introduction Most waterfloods described in reservoir engineering literature involve pattern operations, the most common of which is the five-spot pattern. Only occasiona'lly are linear drives described, even though there probably are increasing numbers being put into operation. Increasing use of linear floods may reflect the accelerating trend towards early application of fluid-injection programs when linear drives are more efficient, as was the case at Little Creek. However. the Little Creek operation is unusual in several respects. It is one of a few successful waterfloods conducted in sands with connate water saturations approaching 60 percent, and it is among the deepest successful water-floods being operated anywhere. Development The Little Creek field was discovered in Jan., 1958, in the lower Tuscaloosa trend in southwestern Mississippi (Fig. 1). The discovery well, Shell-Lemann No. 1, was drilled on a seismic closure about 2 miles southeast of lower Tuscaloosa production at Sweetwater. The well was completed in the Denkman sand at 10,752 ft, and on initial potential it flowed 588 BOPD of 39" API crude on a %+-in. choke; psi was 730 and GOR was 442:l. Development proceeded rapidly on 40-acre spacing, and by the end of 1958 the field was producing approximately 9,100 B/D from 56 wells. Almost all this production came from the northern half of the field. The southern part was discovered in Nov., 1958, at a location almost 2 miles from previously established production. Subsequent drilling established an apparent conneotion about half a mile wide between the twd areas. Development of the field was practically complete by 1961 with the drilling of 155 producers and 35 dry holes. Some early wells were completed open hole but moslt are completed with casing cemented through the productive interval and perforated for production. Geology The lower Tuscaloosa structure in this area is a north-south nose with maximum dips of about 2" on the flanks. There is no discernible faulting at the producing horizon. Productive limits of the field are shown in Fig. 2, which is contoured on a marker just above the main productive zone. A common water level at 10,415 ft subsea was logged at both the northwest and southeast ends of the field. There is a gross oil column of nearly 100 ft (Fig. 2). Since there is less than 40 ft of closure, it is apparent that bhe accumubtion is controlled stratigraphically, being limited by a sand pinch-out across the creslt of the nose. The total produc-

Jan 1, 1969

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By C. T. Wei, A. Kelly

USING a recently developed X-ray method, reported by Schulz,2 it is possible to make a rapid survey of the perfection of a single crystal at a particular surface. This technique has the advantage of allowing a large surface of a specimen to be examined by taking a single photograph and it compares well with other X-ray methods in regard to sensitivity of detection of small angle boundaries. During the course of a survey of the perfection of large crystals of aluminum produced by a number of methods, an examination has been made of a number of single crystals produced from the melt using a soft mold (levigated alumina)." Crystals grown by this method are known, from an X-ray study carried out by Noggle and Koehler,3 to contain regions where they are highly perfect. In the present work, it has been possible to obtain photographs showing directly the distribution of low angle boundaries at a particular surface of these crystals. single crystals were grown from the melt using the modified Bridgman method with a speed of furnace travel of -1 mm per min. These were about 1/10 in. thick, 1 in. wide, and several inches long. The metal was 99.99 pct pure aluminum supplied by the Aluminum co. of America. The crystals were examined by placing them at an angle of about 25° to the X-ray beam issuing from a fine focus X-ray tube of the type described by Ehrenberg and Spear4 and constructed by A. Kelly at the University of Illinois. A photographic film was placed SO as to record the X-ray reflection from the lattice planes most nearly parallel to the crystal surface. The size of the focal spot on the X-ray tube was between 25 and 40 u, and the distance from the X-ray tube focus to the specimen (approximately equal to the specimen to film distance) was -15 cm. White X-radiation was used from a tungsten target with not more than 35 kv in order to reduce the penetration of the X-rays into the specimen. Exposure times were approximately 1 hr with tube currents between 150 and 250 microamp. The type of photograph obtained from these crystals is illustrated in Fig. 1, which shows a number of overlapping reflections from the same crystal. The large uniform central reflection is traversed by sets of horizontal white and dark lines. These two sets run mainly parallel to one another. Lines of one color are wavy in nature and often branch and run together. Large areas of the crystal surface show no evidence of these lines whatsoever. The lines are interpreted as being due to low angle boundaries in the crystal, separating regions which are tilted with respect to one another. A white line is formed when the relative tilt forms a ridge at the interface and a black line is found when a valley is formed. In a number of cases, the lines stop and start within the area of the reflection and often run into the reflection from the edge, corresponding to a low angle boundary starting from the edge of the crystal. The prominent lines run roughly parallel to the direction of growth of the crystal although narrow bands can run in a direction perpendicular to this; see Fig. 2. Although they may change their appearance slightly, the lines tend to occur in the slightly,Same place in the X-ray image and to maintain their rough parallelism when the crystals are reduced in thickness by etching. Thus the low angle boundaries can occur at any depth within the crystal. The appearance of the lines is unaffected by subjecting the crystal to rapid temperature changes, such as plunging into liquid nitrogen or rapid quenching from 620°C. From the width of the lines on the x-ray reflection, values can be found for the angular misorienta-tion of the two parts of the crystal on either side of a boundary. The values found run from 1' to 10' of arc, but values of UP to 20' have sometimes been found, e.g., the widest lines on Fig. 2. These mis-orientations are much less than those commonly found in crystals possessing a lineage structure. When a number of a and white lines occur, running in a roughly parallel direction across the image of a Crystal, the total misorientation corresponding to lines of one color is approximately equal to that corresponding to lines of the other color. The interpretation of the lines as due to low angle boundaries has been checked in a number of ways. Photographs taken with different specimen-to-film distances distinguish lines due to low angle boundaries from effects due to surface relief of the specimen. Normal Laue back-reflection photographs, taken with the beam irradiating an area of the surface showing a number of the lines, show white lines running through each Laue spot. Black lines are set to see by this method. X-ray photographs were also taken, using the set-up described by Lam-one et al.5 when the beam straddles regions giving rise to lines in the Schulz pattern, split reflections are observed within the Bragg spot. The misorienta-tions calculated from the separation of these reflections and that found from the widths of the lines on the schulz technique patterns show good agreement. An exposure was made with Lambot technique of an area of the crystal showing no evidence of low angle

Jan 1, 1956

CONTENTS PAGE HESSE, A. W,-Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells. Discussed by A. W. Hesse, T. G. Fear, George H. Ashley, George S. Rice, W. E. Fohl, R. V. Norris, S. A. Taylor, F. B. Tough, C. W. Gibbs, A. Hurlburt, S. W. Meals 1 DAWSON, THOS. W.-Belt Conveying of Coal at H. C. Frick Coke Company Mines. Discussed by F. F. Jorgensen, Thos. W. Dawson, Graham Bright, A. W. Hesse 13 OTTO, HENRY H.-Ultimate Recovery from Anthracite Coal Beds. Discussed by R. V. Norris, S. A. Taylor, Henry H. Otto, Douglas Bunting, Graham Bright, Howard N. Eavenson, J. B. Warriner 15 HOSLER, Rush N.-Schedule Rating Coal Mines in Pennsylvania for Compensation Insurance Rates. Discussed by E. A. Holbrook, W. W. Adams 17 ARCHBALD, HUGH.-Application of Gaussian Curve to Mining Industry. Discussed by Donald A. Laird, T. T. Read 19 ASH, SIMON H.-System of Coal Mining in Western Washington. Discussed by Eli T. Conner, Simon H. Ash 21 MILLER, J. S.-Method of Mining a Steeply Pitching Anthracite Vein by Successive Skips. Discussed by Eli T. Conner, J. S. Miller, J. B. Warriner 22 HARRINGTON, GEORGE B.-New Orient, an Unusual Coal Mine. Discussed" by George S. Rice, Eli T. Conner, John A. Garcia, George B. Harrington, F. F. Jorgensen, Graham Bright, W. M. Hoen, George N. Simpson, W. C. Adams, R. W. McNeill, Chas. C. Whaley, Carl Scholz, E. T. Gott, Andrews Allen 23 PERROTT, G. ST. J.-Properties of Liquid-oxygen Explosives. Discussed by George S. Rice 48 Safeguarding Coal-mining Operations against Danger from Oil and Gas Wells Discussion of the paper of A. W. HESSE, presented at the New York Meeting, Feb-ruary, 1925, and issued, as Paper No. 1412-F, with MINING AND METALLURGY, February, 1925. A. W. HESSE.-The well under investigation, No. 101, Fig. 2, was started about Sept. 5, 1921, and drilled-in in November. The first hole was started with a 13-in. bit and reached the Pittsburgh coal at a depth of 563 ft.; at 602 ft. the 10-in. casing was run in and the well was continued with a 10-in. bit and 1400 ft. of 8-in. casing was put in. It was then continued to a depth of 1770 ft. and 6-in. casing put in; then continued to a depth of 2555 ft. where the gas was struck. As the well produced only about 100,000 cu. ft. per day. 2-in. tubing was used to conduct the

Jan 6, 1925

[ ]

Jan 2, 1969

Jan 1, 1913