Search Documents

By James Ruddy

THE medical program of the Climax Molybdenum Co. is under the supervision of the department of industrial medicine of the University of Colorado, of which James J. Waring, professor of medicine at the University Medical School, is director. Dr. Waring is consultant and direct supervisor of both the hospital and industrial medical department at Climax. At Climax the program is in charge of the medical director and the associate physician, Dr. Galen M. Hover. The hospital at Climax is completely equipped with all that is necessary for the practice of scientific medicine and surgery. Only graduate registered nurses with experience in industrial medicine are employed. Being only a few hundred yards from the portal of the mine. acci-

Jan 1, 1946

By P. E. Demmler

The apparatus in which the process of bright annealing of copper wire was carried out consisted of a section of iron pipe, 6 ft. long and 3 ft. in diameter. The pipe was provided with flanges to which were bolted the end plates for sealing, also with inlet and outlet tubes to allow for the displacement of the air in the pipe by natural gas. After charging with copper wire, sealing and displacing the air, the pipe was heated to 350' C. (662" F.). It was expected that the natural gas would furnish a neutral atmosphere which would prevent oxidation and give a satisfactory bright-annealed product. It was found, however, that the outer layers of wire were discolored and not suited for the use for which they were mtended. To obtain an idea of what was taking place in the annealing furnace, skeins of the hard-drawn wire were placed in a glass tube so that all changes in appearance could be observed as they were heated to different temperatures and under varying conditions. The temperature in each case was determined by means of a thermocouple placed in the tube close to the wire. Following is a summary of the results of these experiments: 1. When the wire was heated for 1 hr. in a current of natural gas at a temperature of 350") 400") or 500" C. (662", 752", or 932" F., respectively), there was a marked darkening of the wire throughout the skein. 2. When heated for 1 hr. in natural gas at a temperature of 600" C. (1112' F.), there was no coloration, the wire remaining clean and bright. 3. When heated in natural gas to 350" C. until darkened and the treatment continued with the temperature raised to 600' C., the coloration disappeared and the wire became clean and bright.

Jan 1, 1923

By P. E. Demmler

The apparatus in which the process of bright annealing of copper wire was carried out consisted of a section of iron pipe, 6 ft. long and 3 ft. in diameter. The pipe was provided with flanges to which were bolted the end plates for sealing, also with inlet and outlet tubes to allow for the displacement of the air in the pipe by natural gas. After charging with copper wire, sealing and displacing the air, the pipe was heated to 350' C. (662" F.). It was expected that the natural gas would furnish a neutral atmosphere which would prevent oxidation and give a satisfactory bright-annealed product. It was found, however, that the outer layers of wire were discolored and not suited for the use for which they were mtended. To obtain an idea of what was taking place in the annealing furnace, skeins of the hard-drawn wire were placed in a glass tube so that all changes in appearance could be observed as they were heated to different temperatures and under varying conditions. The temperature in each case was determined by means of a thermocouple placed in the tube close to the wire. Following is a summary of the results of these experiments: 1. When the wire was heated for 1 hr. in a current of natural gas at a temperature of 350") 400") or 500" C. (662", 752", or 932" F., respectively), there was a marked darkening of the wire throughout the skein. 2. When heated for 1 hr. in natural gas at a temperature of 600" C. (1112' F.), there was no coloration, the wire remaining clean and bright. 3. When heated in natural gas to 350" C. until darkened and the treatment continued with the temperature raised to 600' C., the coloration disappeared and the wire became clean and bright.

Jan 1, 1923

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years' history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.' The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field's history subsequent to Jan., 1952 (see Fig. 1)'.

By AIME AIME

ON March 14, the University of Tulsa was accepted as a member of the North Central Association of Colleges, which ranks Tulsa among the leading universities of the country. A. G. OIiphant recently donated to the new school of petroleum engineering a splendid collection of books on geology, valued at $25,000. Waite Phillips, an oil producer and chairman of directors of The Independent Oil & Gas Co., donated $150,000 for a petroleum engineering building

Jan 1, 1929

By Harmel A. Dawson, Robert A. Wilson

First the basic steps to determine the values present and the minerals involved which are the basis for the metallurgical testing are presented in this paper. Next, choosing the process or processes indicated for treating an ore are discussed. This is followed by the test procedures used, the results of which will indicate amenability to treatment. These test procedures have been developed, used and proven effective in laboratory evaluations relative to plant processing. Special, uncommon processing is beyond the scope of the paper. Evalutation of test results and incorporation into the preliminary and final flow sheet for plant design are discussed. The value of a flow sheet, with material and water balances, to plant design is shown.

Jan 1, 1978

By J. A. Wilcox

A NEW LINE of specialists has arisen as a result of the trend toward labor socialization and collectivism in all branches of industry. These men are the ones who will govern the destiny of many companies and the labor policy of our government in coming years. They must be men of integrity and of rather exceptional qualifications; men who can foresee the trend of labor relations with business, and who are willing to sacrifice the immediate fruits of technical training for manual labor and study. They must take their place in industry, not with the idea of following the orthodox line of advancement, but knowing that they must stay at the bottom until they have learned to understand the viewpoints, the work, the advantages and the disadvantages of each classification of labor. They must not be of a radical nature or become easily biased, and they must study. You will say I am looking for a superman and in one sense that is true, but the business man and our government are both in the market even now for this type of man, and with the proper training and background, many of our young technicians can readily enter this field of work.

Jan 1, 1942

By W. A. Thomas

Steam is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 Ib., are used for power out of each ton produced. In the complete electrification of anthracite mining operations, no set rule can be given for the power requirement, in kilowatt-hours per ton, as conditions vary widely in the matter of pumping, ventilation, and transportation, but the following cases are given as a basis of determining a range and a possible average power requirements:

Jan 1, 1922

By D. B. Hobbs, L. W. Kempf, R. S. Archer

Silicon is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17s and 51s of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both 'normal" and "modified" sand castings. Review of Literature The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By L. B. Ticknor, M. B. Bever

An isothermal calorimeter suitable for measurements of heats of solution in liquid tin as solvent is described. Measurements of the heats of solution of gold, silver, copper, and a gold-silver alloy are reported. The heat of formation of this gold-silver alloy is also reported. HEATS of solution in liquids can be determined directly, but few such data have been published for metals as solvents. Knowledge of heats of solution is desirable because it contributes to the general understanding of energy relations in metallic solutions. Thermochemical measurements of this type also furnish answers to specific problems: For example, from the heats of solution of an alloy and of a mixture of its constituent elements in a given solvent, the heat of formation of the alloy may be found. Similarly, differences in the energy content of samples of the same metal in two different states, such as the annealed and cold worked states, may be determined. In the work reported here, gold, silver, and an alloy of gold and silver were dissolved in liquid tin at 240°C and gold, silver, and copper were dissolved in tin at 300 °C. The experiments yielded the heats of solution of these metals in tin. The heat of formation of the gold-silver alloy was also determined. The same calorimetric method is being used to measure the energy stored in metals during cold working and preliminary results have been published.&apos; Equipment and Experimental Procedure The isothermal calorimeter used in this work, Fig. 1, consisted of a Dewar flask completely immersed in a constant-temperature salt bath. A long neck provided space for thermocouple leads and a stirrer shaft and permitted the injection of solute samples. The metal bath in the calorimeter flask was stirred at about 100 rpm by a small glass impeller driven by a constant-speed motor. The shaft of the stirrer passed through a Wilson vacuum seal.2 All measurements were made under vacuum in order to eliminate temperature disturbances resulting from gas convection and to prevent the oxidation of tin. The calorimeter flask was joined by an all-glass connecting line to a gas-control system which made possible the use of a protective atmosphere of deoxidized and dried hydrogen. At the operating temperature of the calorimeter tin oxide was not reduced by hydrogen, presumably because the reaction rate was too slow. Part of the closed system was a removable side tube through which the solute sample could be introduced and in which it was held at a temperature of 0°C prior to injection into the metal bath. The salt bath containing a mixture of sodium, lithium, and potassium nitrates was similar to that described by Beattie3 and was equipped with a stir-

Jan 1, 1953

By C. F. Nagel

This paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. Heat Treating Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this irnprovement may be illustrated by some typical properties of dura-lurnin (Table 1). It is essential that the material be in the wrought condition in order to obtain rnaximum heat-treatment effects. In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By G. H., Wigton

THE present milling operations of the Chief Consolidated Mining Co. consist- of flotation of oxidized minerals from siliceous ores of the Tintic Mining district, Utah. As the lead, silver, and gold minerals that give the ores economic value are almost entirely oxidized; their successful flotation has necessitated the solution of many new problems. Laboratory effort resulted in the selection of a, natural float for the oxidized minerals. &apos;By "natural float," I mean that no reagent was added to produce a sulfide film on the osidized minerals before or while subjecting them to flotation operations. As compared to methods involving sulfide filming, the natural float was selected because it promised successful treatment of a larger variety, of ores without change in quantity or kind of reagents, as well as a better economic balance between metal recovery and concentration ratio. In explanation, I can, state that with sulfide filming, the efficiency of the method decreases rapidly with increase of hydrated, iron osides in the ore, whereas with the natural float the same effect has not been noted. Evidence shows that although sulfidizing can produce greater metal recoveries, it yields a concentrate so much lower in grade that no advantage results.

Jan 1, 1928

By Hugh P. Nicholson

IN view of the many articles that have been written on the proper classification of mining systems without so far having produced any particular tangible results it might seem that the subject is hopeless of solution. I do not believe that is so, and my intention in contributing the following outline is to present a slightly different viewpoint. Too much attention is often focused on unnecessary details and not enough on general principles. Too much attention and emphasis is often given to the system employed at one particular mine or in one particular district. In addition, names that are entirely misleading are applied to mining systems, and their adoption by the coming generation perpetuates a condition that needs clarification badly. The following classification is the result of several years of practical experience in mining and also several years&apos; practice in teaching the same subject. It therefore represents a broad picture of the entire field of mining systems from the viewpoint of the miner as well as the teacher. It seems that the difficulty in the past has been in reconciling these two viewpoints. The need of such a reconciliation requires no explanation.

Jan 1, 1934

By E. G. SINCLAIR

DRILLING wildcat wells in Wyoming differs a little from methods used in any other field. Here it is always advisable to start the hole as large as is convenient in order to carry each string of pipe as far as possible, so that drilling can be continued a thousand feet deeper if necessary, as there is always sand a few hundred feet ahead that really ought to be tested. This plan may seem ambitious, but if it is adhered to, it will save a great deal of trouble before the well is completed. In making the location, one representative from the operating department and one from the geological department should work together, so that the well may be in the best possible place for obtaining oil and the most feasible place to drill for the operating department. In Wyoming nearly all wells are drilled with standard tools, as with them a better log can be kept and better time made in completing the hole. The shales of Wyoming are very hard and do not mix well in a wet hole. The shale cuts into large pieces, too large to be circulated out of the hole, and forms a mat on the rotary which soon cuts off circulation. Then if this mat cannot be jarred from the bit, the drilling string has to be pulled and the mat cut off from the bit with a pick or an axe. I have seen standard tools come out of a wet hole with 10 to 16 in. of mat on the bottom of the bit. Rotary tools have drilled wells satisfactorily in the Big Muddy field and at Billy Creek, but in the other fields the wells have been drilled much more economically with cable tools.

Jan 1, 1926

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.&apos; Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith&apos; examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn&apos;s suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.&apos;" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953

By Paul Averitt

require both time and money. Any attempt to secure a quick answer will yield a figure that very likely cannot be substantiated, and certainly will not yield information in the detailed form now desired. It will be about 10 years before a completely new estimate can be prepared for the coal reserves of the United States at our present rate of progress, though of course, much information will be available in the interim. We would like to present such information as we obtain in the form most acceptable to the industry, and to that end we are working closely with coal resource committees of the AIME, the National Bituminous Coal Advisory Council, and the Bureau of Mines. DISCUSSION G. H. Cady*—Mr. Averitt&apos;s description of the nature of the coal resources investigations of the United States Geological Survey and the progress of this work is very timely in view of the general interest in the subject of coal resources. The Federal Survey is obviously taking the "long view" with respect to the appraisal of the coal resources as part of the preparation of the general geological map of the country and the attendant determination of the quantity of all mineral and fuel resources. It is apparently for regional surveys of the conventional type that the detailed procedures employed by the Federal Survey are applicable. Even if so it is somewhat unexpected to find the same criteria for evaluation will be applied to the country as a whole. The work on coal resources appraisal has been proceeding at various rates in a number of coal producing states for various periods. Undoubtedly since there has been no common practice in the method of appraisal the states each have worked independently and independently of the Federal Survey, and each has adopted certain practices to meet local conditions. I do not know how much consideration has been given by the U. S. Geological Survey to these practices. It seems probable that such consideration might result in important modifications of the standards which apparently have been set up by the Federal group in line with local requirements. It is the practice in some state surveys to present the facts in regard to the occurrence and distribution of coal beds and their variations in thickness down to thicknesses of 1 to 1 1/2 ft in relatively narrow stages up to maximum thickness. It is then possible for any one using such figures to compile quantitative estimates of workable coal at various minimum thickness limits. This is a desirable objective where surveys are detailed and information correspondingIy good. However, vast quantities of coal lie in beds that are relatively thin about which little information is available and the quantity of such coal might affect the final appraisal to the extent of several thousand million, depending upon the minimum limitation observed. Thus in the case of Illinois a difference of 1 ft in average thickness of coal in the coal field would make a difference of approximately 35 billion tons in the estimated quantity present. One is dealing with a very large area and small differences in thicknesses are very irnportant in the overall picture. The estimate of 10 years to accomplish the sort of detailed appraisal outlined by Mr. Averitt is viewed somewhat skeptically and certainly would require many more trained geologists than seem to be available. The requisite detailed mapping and study are very time consuming not only because of the geological field work required, which is difficult in certain seasons, but also in order to assemble data from company and personal files, and to study drill records and cores, and to sample and analyze the coal. Unless the staff of geologists could be increased in the order of several hundred per cent the prospects are that the appraisal of the type suggested will require many decades not just one. The permanent value of such appraisal, however, is not questioned and it should be expedited as rapidly as means allow. Satisfactory appraisal is not easily achieved and will vary from time to time. The main function of a geological survey is to collect and present the facts that will make possible appraisal in terms of existing conditions by individuals, particularly engineers, qualified by training and expcrience for making such estimates. Thickness and character of the coal bed, nature of the overlying and underlying strata, position, thickness, and character of "partings," relationship to other coal beds, and a variety of other factors must be assembled by the geologist in order to present a complete picture of the geological setting. The economic and engineering factors are in general outside the field of geological experience. The geologist should see to it that the pertinent geological facts are available; much more information than simply thickness and depth of the coal beds is essential to meet all the requirements of appraisal in the future as well as at present. With respect to the present demand by engineers and coal mine operators and others for a rapid re-appraisal of the available coal resources, in the light of existing practices and those in immediate prospect, the Federal procedure of systematic mapping and appraisal is scarcely in line. It will be necessary for those particularly interested in having such an estimate made to establish standards with respect to the various factors involved so that the scope of the geological work can be definitely restricted for the various coal fields. There is little use in setting up general standards since no such standards will be applicable to all fields. Thus it is folly to establish a standard minimum thickness to be generally applicable which is one-half to one-third the minimum minable thickness in some fields. The greatest difficulty in appraisal of the presently actually workable coal bed lies in the variation in the importance placed on roof, floor, structural conditions, bedded impurities. sulphur content and other factors that affect judgment relative to the value of a coal bed. It is doubtful whether any appraisal will have universal approval in view of the variable factors involved. For this reason if none other, the facts should be carefully and painstakingly assembled after the manner of a systematic geological survey such as that advocated by Mr. Averitt. Only upon the basis of sucb information can reliable estimates be made in line with selected conditions. Paul AveRitt (author&apos;s repty)— In this paper I discussed, but did not define as such, two major phases of our activities on coal, which are closely related, and which normally we in the U. S. Geological Survey see as an integrated whole. It is understandable, therefore, that Dr. Cady should assume that my remarks applied only to the current work on coal reserves with which I am directly concerned. In view of Dr. Cady&apos;s discussion, however, I think a brief summary of the two phases of U. S. Geological Survey activities on coal will be appropriate. The long-term function of the U. S. Geological Survey on coal investigations is to make detailed geologic studies, involving the preparation of detailed geologic maps showing the outcrops and correlations of coal beds, direction and dip of coal-bearing rocks, nature and thickness of overburden, location of faults and fold axes, and similar features. Such studies also yield many measured sections of coal and associated strata, which show variations in the thickness of the beds, and the intervals between coal beds. Taken as a whole, detailed geologic studies provide much useful information for mine operators and engineers. As Dr. Cady points out, this type of geologic work is arduous and time consuming, but it provides the basic data that are necessary both in the development of our coal fields, and also in the preparation of coal-reserve estimates, which are discussed in the next paragraph. The U. S.

Jan 1, 1950

By Gary Beerkircher

The mine hoisting equipment that is selected and installed at a mine is the lifeline of the mine, and therefore the proper selection of equipment will save a lot of time and money during the life of the mine. Various types of mine hoist designs &e available today, and each has their advantages and disadvantages. Double Drum Hoists, Single Drum Hoists, Friction Hoists and various special designs of these are available but should only be used on applications where they are suitable. There have been several new drive systems for mine hoists which have come into the picture in the last ten years, and they in turn must be evaluated along with the existing drive systems for each hoist application. It does not make sense to properly select the hoist mechanicals, and then have a drive system that turns out to be a bottleneck. This paper will attempt to cover the above noted systems - both the hoist selection and hoist drive system that will provide the mine with a reliable and economical hoisting system. I. Mine Hoist Types There are two basic types of mine hoists available in the world today: the drum hoist on which the hoist rope is actually stored during the hoisting cycle, and the friction (Koepe), which merely passes the rope over the wheel during the hoisting process. Following is a general outline of each type of hoist and the hoisting applications that they are suitable for. First let us consider the simple Single Drum Hoist. As a Service or Production Hoist with cage or skip in balance with a counterweight, a Single Drum Hoist can efficiently service one or more levels since the location of the counterweight at anytime is not important. As a Production Hoist with skips in balance the Single Drum Hoist is best used for single level hoisting. All rope adjustments for proper spotting must be done manually for the Single Drum Hoist. This has to be done periodically to compensate for rope stretch. A variation of the Single Drum Hoist is the divided drum hoist. If multi-layer winding is necessary the Single Drum Hoist must have a divider to allow a separate compartment for each rope. If a counterweight is used with a divided drum application the counterweight rope can be wound on a smaller diameter (Figure 2). Consequently, it moves a lesser distance than the main conveyance and rope adjustment problems are reduced.

Jan 1, 1975

By A. F. Lucas

EACH day, the fact becomes more evident that the ever-growing demand for oil is farther outstripping production, regardless of the increase in output throughout the past twenty years. The development of known oil fields and the prospecting for new ones along present lines are not resulting, in, and cannot bring forth, supplies large enough adequately to meet the oil needs of the country. The usual methods of prospecting-for new supplies are insufficient to meet the exigencies of the situation which threatens, in the not distant future, to reach a critical stage. Were it not that within the last two years new and prolific oil fields have been discovered in northern Louisiana, central Texas, and California, this crisis would undoubtedly be now at our door. Stocks are being exhausted in spite of the rapid growth of imports. The time is therefore fast approaching when some radical departures must be made in the method of prospecting and developing old and new fields in order to increase our oil supplies. Methods and chances, that have seemed unwarranted will not only be given serious consideration, but, according to the results promised, will be put to the test. Meanwhile, however, nearly all the oil fields are responding to the stimulus of higher prices, whereby enormously growing capital is attracted to this important industry, both here and abroad; the increase in our petroleum production at the present time is due to this circumstance. Yet, although a most active search is being made for possible sources of additional supply, one section of our country is not yielding the results that, in my opinion, it is capable of producing: I allude to the coastal dome belt of Texas, Louisiana, and Mexico. The United States Geological Survey has estimated that three-fourths of a billion barrels are available in the ground in the Coastal Plain of the two states just mentioned. Numerous papers have been written on the subject of the salt domes of the Coastal Plain and more or less attractive theories have been advocated by leading geologists to account for their origin and the presence of the oil, sulfur, and salt associated in them. However, owing in part to the generally monotonously level country in which the coastal

Jan 9, 1920