Search Documents

By Jei Y. Choi, Paul G. Shewmon

The surface self-diffusion coefficient of copper (D,) has been measured between 847° and 1069 "C for six different orientations. These were the(111), (110, (100, and three higher index surfaces. The activation energy for Ds (designated Q s) was found to be about 49 kcal per mol for all six surfaces, and Do about 2 x 104 sq cm per sec. At any temperature Ds varied by no more than a factor of three over these orientations. It is shown that, if the free energy of a surface atom is uniquely determined by its number of nearest neighbors, it follows from the Principle of microscopic reversibility that Qs should have the same value for all surface orientations, and Ds should vary little with orientation. This model also suggests that for clean fee metals Qs ~ 2/3 AH, (heat of vaporization). This is true for copper. ALTHOUGH it has been appreciated for several decades that atoms can diffuse more rapidly on a surface than through the bulk of a crystal, it has only been in the last few years that reliable values of the surface self-diffusion coefficient (Ds) have become available. Tracer studies of Ds had been attempted prior to this period, but when a tracer is placed on a surface, an ever increasing fraction of it is drained off into the lattice. The correction for this loss involves a very difficult, and as yet unperformed calculation. Those who have worked with tracers have not corrected for this loss.1, 2 Thus their results indicate that Ds is greater than the self-diffusion coefficient in the lattice (Dl), but it has not been established that they give quantitative data on Ds. A procedure which avoids the problem of tracer loss is to study the rate of mass-transfer under the effect of surface tension. If the surface asperity being studied is very small, the mass transfer occurs entirely by surface diffusion. The kinetics at which a grain boundary groove forms on an initially plane surface is a well-studied case of this type. The smoothing of a slight scratch in an otherwise flat surface is another procedure that has been studied. If these grooves are up to 20 to 30 µ in width, the dominant mechanism for mass transfer is surface diffusion (at least in the case of metals with low vapor pressures), and the widths can easily be measured with an interference microscope. Of these two, mass-transfer techniques only in the case of grain boundary grooving has a rigorous mathematical treatment been given. This was done by Mullins.3,4 His analysis predicted that in the case of copper in an atmosphere of an inert gas, surface diffusion should be the dominant transport mechanism. This analysis gave an equation for the groove profile and predicted that the width of the groove would increase as (time)1/4. Mullins and Shewmon showed that both of these predictions agreed with experiments.5 Thus the validity of the values of Ds given by this procedure seems to be well established. Gjostein has used copper bicrystals and the grain boundary grooving technique to determine Ds and the activation energy for surface selfdiffusion (9,) in the [001] direction on surfaces ranging between the (100) and (110) planes.= He reported that Qs = 41 kcal per mole and Do = 6.5 x 102 sq cm per sec for all orientations studied. Since the results did not change with the dew-point of the dry hydrogen atmosphere or the type of refractory tube used, he concluded that the surfaces were clean, or at least that the results were not influenced by any impurities chemisorbed from the atmosphere. The work reported here reproduces and extends Gjostein's study in that D s and Q s were determined for copper over a wider range of orientations. To study the effects of impurities, two purities of copper were used as well as cathodic etching to remove any possible electropolishing film. Gjostein postulated that the diffusing atoms on a surface near a low index plane are the few atoms which are adsorbed on the smooth region between ledges or steps in the surface. A more rigorous derivation of the equation relating Ds to the concentration and jump frequency of these adsorbed atoms is given here. Using this treatment, our empirical observation that Q s and D s are essentially the same for all surface orientations can be shown to follow from the assumption that the free energy of a surface atom is uniquely determined by its number of nearest neighbors. The studies of D s using the scratch technique have been carried out by Blakely and Mukura on nickel,' and by Geguzin and Oveharenko on copper. The latter study using copper gives values of D s roughly

Jan 1, 1962

By Yoichi Ishida, Ching-Yao Cheng, John E. Dorn

Tile creep behavior of a iron was investigated over the range of temperatures from 375° to 1150°K. Apparent activation energies for creep, obtained by the effect of sudden changes in temperature on the creep rate, revealed the presence of- four distinguishable regions. The creep behavior of a iron in Regions II (480° to 774°K) and 111 (775° to 1045°K) was found to correlate well with a model where the creep rate is controlled by the nonconsevualive motion. of jogged screw dislocations. An anomalous increase in the apparent activation energy fur creep in Region III was found to be in harmony with the known decrease in the free activation energy for self-diffusion over the Curie transformation range. Furthermore, the creep rates in Regions II and III were found to increase with stress due not only to the effect of stress on the activation energy but also to an increase in density of mobile dislocations. The evidence suggests that pipe diffusion along moving dislocations could be a significant factor over the lower temperatures of Region II. ALTHOUGH the creep properties of iron and steel have been of interest to metallurgists for some time and an extensive literature is now available, most of the published information has not produced much toward understanding the fundamental dislocation processes controlling the creep behavior of these materials. Whereas the activation energy for high-temperature creep of metals usually agrees well with that for self-diffusion, Sherby, Orr, and Dorn1 deduced from the data of Tapsell -and c1enshaw2 that the activation energy for creep of Armco iron is about 78,000 cal per mole and more recently Lytton and sherby3 reviewed the data of Jenkins and Mellor4 and found an activation energy for creep of a iron of 80,000 cal per mole. Both values are substantially greater than the activation energy for self-diffusion in a iron. Because of the limited data suitable for purposes of identifying the controlling dislocation mechanisms of creep and the unusually high activation energies for creep quoted above, it was considered desirable to reinvestigate in detail the creep of a iron by more reliable techniques which would provide sufficient data for determination of the creep mechanisms. EXPERIMENTAL TECHNIQUE Creep specimens were prepared from 3/8 by 4 in. iron bar stock of the following composition by weight percent: 0.001 C, 0.0120 0, 0.001 N, 0.004 S, and 0.003 P. The as-received bars were cold-rolled to a thickness of 0.100 in., annealed under argon for 30 min at 1113°K, cold-rolled to a final thickness of 0.063 in., and machined into tensile specimens having gage section 0.250 in. wide and 1.70 in. long. Finally they were recrystallized under argon at 1113°K. Specimens to be crept above 1060°K were recrystallized at 1173°K. Both recrystallization treatments gave the same reproducible equiaxed ASTM No. 4 grain size. Creep testing was conducted in machines fitted with Andrade-Chalmers arms that maintained a constant stress to within ±0.2 pct of the reported values. Deformation over the specimen gage section was sensed with a linear differential transformer and recorded auto-graphically as a function of time. The strains deduced from these measurements were sensitive to ±5 x 10-5. During creep the specimens were contained in an argon-filled chamber which was immersed in a temperature-controlled molten tin bath. Creep temperatures, as measured by thermocouples attached to the specimen, were maintained to within ±10.25°K of the reported values. For activation-energy determinations rapid changes in temperature of about 12°K were obtained within 30 sec by direct resistance heating of the creep specimen, and maintained to ±1°K of the reported values. Observations of structural details of specimens before and after creep tests were made by electrolytic polishing and etching in acqueous ammonium persulfate. EXPERIMENTAL RESULTS A typical example of the determination of apparent activation energies, Q, by the effect of small changes in temperature is illustrated in Fig. 1. Q is defined by

Jan 1, 1967

By Thomas V. Falkie

The use of operation research and computer techniques in the mineral industries continued to gain acceptance during 1966. There are generally at least five sources of information for researchers and practitioners in the field: (1) Technical periodicals like MINING ENGINEER- ING, Mining Congress Journal, etc. (2) Proceedings of the Symposium and Short Course on Computers and Operations Re- search in Mineral Industries, held last year at Penn. State University and jointly sponsored by the University of Arizona, Stanford University, Colorado School of Mines, Penn. State University and the Society of Mining Engineers of AIME. (3) Various local conferences, such as the 1966 Rocky Mountain Minerals Conference held in Denver. (4) United States Bureau of Mines publications. (5) The AIME annual meeting in New York and the SME Fall Meeting in Tampa.

Jan 2, 1967

By S. C. Hollister

An evaluation of the function of the engineer, so that means whereby education can best serve his needs can be adopted. THERE has been a steady increase in specialized branches of engineering during recent years. Some of these are simply specializations in the function of engineering, such as welding engineering, tool and die engineering, petroleum engineering, and refining engineering. Others are associated more closely with the basic sciences, as for example, geological engineering or engineering physics. Still others tend toward the border line of business, such as administrative engineering or general engineering.

Jan 1, 1950

By Francis H. Brownell

During the 1920's lead consumption in the United States reached the highest average total ever known. For the ten-year period 1921-'30, it was slightly over 600,000 tons per year, or say 50,000 tons per month, and the price averaged 6.81 per lb. But the I930's witnessed a severe drop in the consumption of lead is in other business activities. The average U.S. consumption for the ten-year period 1930-'40 was slightly less than 380,000 tons per year, or under 32,000 per month, with the average price dropping to 1.191c. per lb. The outlook in early 1939 was for a continuation of this average consumption and price a demand of 35,000 to 40,000 tons per month, and a price level of 4 1/2 to 5c. in the United States.

Jan 1, 1941

By John E. Conley

THE production of lime by the burning or calcination of limestone, including all varieties from true dolomites and magnesian limestones to high-calcium types, continues as one of the essential basic industries. In 1937, a total of 4,124,165 tons of lime valued at approximately $30,091,000 was produced in the United States.1 The importance of any contribution to our knowledge on the mechanism of the lime-burning process is, therefore, obvious. The burning of limestone has been practiced since the earliest days of our civilization, and the literature on the various phases of the industry is voluminous. Calcination of the various types of limestone has been studied by many previous investigators, but some points require additional research. Each occurrence of limestone provides an opportunity for specific investigation, because the characteristics of stones in different localities vary Knibbs13 has given an excellent discussion of available data on the theory of lime and magnesia burning. The thermal dissociation of calcium carbonate has been studied more recently by Johnston,2 Smyth and Adams,3 Ralston et al.,4 Furnas,5 Potapenko,6 and Southard and Royster.7 As a result of these investigations the dissociation temperature at atmospheric pressure has been established as 894º to 898º C. The dissociation of dolomite and magnesite, although studied by several investigator,4, 6, 8 still requires clarification by additional data. The calcination of limestone was studied for a twofold purpose: (1) to extend our information on the mechanism of the lime-burning process and (2) to standardize the conditions for calcination of high-calcium and dolomitic limestones for subsequent hydration tests on the lime.

Jan 1, 1939

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By Henry M. Howe

THIS paper gives the composition of the iron and slag at different stages in the "air-furnace" process of preparing "hard metal," or white cast-iron, for conversion into malleable cast-iron by annealing. The details of the process are given in an appendix. One of us had been trying for years to work some chemist of some of our malleable-iron works up to a degree of enthusiasm which would lead him to make such au investigation. It would have had the advantage of the greater familiarity with the conditions which one habitually on the spot must have. Failing in this, he made use of an opportunity which presented itself of taking samples here represented, with such fairness as the conditions permitted, holding firmly that a rough approximation to the truth is better than the complete lack of data, or that a bird in the hand is worth two in the bush. We hope that this attempt may stimulate others effectively to duplicate this work, and thus correct or confirm it. Our results are shown in Table I. and graphically in Figs. 1 and 2. Discussion.-At the time when the first two samples were taken, the metal and slag were still too sluggish to permit fair sampling, and not until sample 6 were the conditions really favorable, because at the time of the fourth sample the metal was not fully melted, and even at the time of sample 5 it was still sluggish. Indeed, the slag was probably very heterogeneous throughout, because it took up silica and alumina rapidly from the bottom, and because it was so siliceous as to be sluggish at this relatively low temperature. This hetero-geneousness is exaggerated in the two samples of slag 8, apparently by the great viscosity due to its extraordinary acidity. Note that the manganous oxide of one sample is about two and

Mar 1, 1909

By H. D. Outmans

The mechanics of filtration are described by a theoretical-empirical nonlinear diffusion equation which, under certain circumstances, may,be linearized and then solved explicitly. For filtration under static conditions linearization leads to a boundary value problem analogous to a heat flow problem with a known explicit solution. The corresponding solution for static filtration is compared with published experimental data. Under dynamic conditions filtration takes place in three successive stages. During each of these the rate of filtration and/or the thickness of the filter cake are different functions of the filtration time. The proposed mechanism explains the observed high resistance of dynamically deposited filter cakes against erosion and also the connection between filtration rate and viscosity of the drilling fluid. Several of the quantities governing dynamic filtration have no counterpart in the static filtration mechanism. The static filtration rate is, therefore, not a reliable measure for the dynamic rate and vice versa. INTRODUCTION Filtration under simulated borehole conditions, i.e.. either from a static suspension or from a suspension flowing parallel to the filter cake (dynamic filtration), has been the subject of several laboratory studies.1-7 This experimental and theoretical work showed that many aspects of the filtration mechanism cannot be explained by an elementary filtration theory based on the assumption that the filter cake is incompressible. For a more satisfactory theory compressibility should be taken into account. This has been done. at least to some extent, in the filtration theory developed for the chemical industry. Surveying the literature (see Ref. 8 for a bibliography) it becomes apparent that, although several properties of filter cakes deposited from many different suspensions have been measured, including compressibility, the filtration equations are essentially empirical in nature. No attempt has been made, for instance, to develop filtration theory along the lines of consolidation theory.12 This theory, upon which a highly successful development in soil mechanics rests, would appear to be an excellent starting point for a filtration theory since the compressibility concept is an essential part of it. As we will use this theory in the following development it is well to state the four assumptions on which it is based: 1. The fluid flow through a compressible porous medium is governed by Darcy's law. 2. The rate of change in fluid content of an element of the porous medium is proportional to the rate of change of solid pressure between the particles. 3. The solid particles are incompressible within the range of pressures considered. 4. The total pressure on a surface normal to the line of flow is equal to the sum of the fluid pressure and the pressure between the particles (solid pressure) at that surface. To calculate the rate of filtration and other quantities of interest it is necessary to know the filter cake compressibility and the permeability as a function of the solid pressure. It has not been possible to calculate these functions from theoretical considerations and they will therefore be introduced in this paper as empirical expressions. Both are determined in a compression cell where the cake is subjected to a mechanical load. Permeability and compressibility are measured after the solid pressure has stabilized, i.e., after the excess fluid pressure has been dissipated and the uniform pressure is transmitted entirely by the solids. The permeability and compressibility thus determined are not the same as during filtration in the borehole, under either static or dynamic conditions, because then, due to frictional drag, the solid pressure and hence also the permeability and compressibility vary along a line normal to the direction of the mean flow and can only be defined locally. DERIVATION OF THE FILTRATION EQUATION FOR COMPRESSIBLE FILTER CAKES As the filter cake in the borehole is thin compared to the radius of the hole the filtration may be considered as linear. Taking the x-axis normal to the wall, with its origin at the formation, we have, according to Darcy's law,

By C. Chu

An investigation has been made of the radial heat-wave process using a mathematical model in two-dimensional cylindrical coordinates. This model considers combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. From a study of the general features of the process, an important phenomenon has been revealed, namely, the feedback of heat into the reservoir on the trailing edge of the heat wave. The effects of various process variables on the performance characteristics of the process have also been investigated. It was found that up to the time when the combustion front reaches a given point, the per cent heat loss, provided it is not higher than 40 per cent, is approximately directly proportional to the square root of thermal conductivity arid fuel content, but inversely proportional to the square root of gas-injection rate and oxygen concentration. The effecr of reservoir thickness is more pronounced, since halving the thickness doubles the per cent heat loss. The most decisive factor in determining the center-plane peak temperature is the fuel content of the reservoir. Within the temperature range investigated, doubling the fuel content doubles the peak temperature in the early stage, but the rate of decline of the peak temperature is high. Reservoir thickness is also a very influential factor. The peak temperature is lowered when the thickness is reduced; however, the effect of thickness becomes less pronounced when the thickness is high. Reduction of oxygen concentration increases the peak temperature in the early stage but lowers it afterwards because of the higher rate of decline of the peak temperature. Increase in gas injection rate or decredse in thermal conductivity geives a higher peak temperature which stays high for a longer period. The propagation range of the heat wave is chiefly governed by the fuel content of the reservoir. An increase of 0.2 1b/cu ft in the fuel content increases the propagation range by 100 per cent. The propagation range is more than doubled by doubling the gas injection rate, or reservoir thickness, or by reducing the thermal conductivity by 50 per cent. Comparatively, oxygen concentration has less effect on the propagation range. INTRODUCTION Several investigators have conducted theoretical studies of a radial heat wave. Vogel and Krueger1 studied a system with a moving cylindrical heat source of constant temper- ature, considering conduction in the radial direction only. Ramey2 included conduction in the vertical direction in his studies. Bailey and Larkin2 attacked a more general problem where initial well heating, vertical heat losses and arbitrary frontal velocities were included. In all these studies, however, conduction was considered to be the only means of heat transfer. Bailey and Larkin in a later paper included the effects of convection in a study involving both linear and radial geometries. Vertical heat losses were neglected in the radial case. Katz5 studied a similar problem in a one-dimensional radial model, using a heat-loss coefficient to account for vertical heat losses. Selig and Couch6 mployed a cylindrical model and investigated two limiting cases. In one case they considered no heat loss from the reservoir whereas in the other they assumed a constant temperature at the interface between the reservoir and its bounding formations. Thomas' studied a more general case but assumed a permeable bounding formation so that the convection effect is not confined to the reservoir. In the present work a more realistic and more generalized model is used. It involves a two-dimensional cylindrical system with combustion, convection and conduction inside the reservoir, but only conduction in the bounding formations. The purpose is to establish the temperature distribution both inside and outside the reservoir, to study the general features of the radial heat wave process, and to investigate the effects of various process variables on the performance characteristics of the process. THEORY We fist consider a circular porous reservoir of thickness H extending vertically from y = — H/2 to y = + H/2. The reservoir extends from a well bore radius r, to an external radius re. A stream of oxygen-containing gas is introduced into the reservoir through the wellbore. The oxygen-containing gas reacts with the fuel contained in the reservoir and forms a combustion front wherever the prevailing temperature can support the combustion. It is here assumed that this combustion front constitutes a cylindrical surface source of heat having an infinitesimal thickness in the radial direction and extending vertically throughout the whole thickness H. This is designated as Region I. We next consider a Region II corresponding to the upper and lower formations bounding the reservoir, extending from y = — - to y = — H/2 and from y = + H/2 to y = + m. Since r, is very small, we may assume that the two bounding formations have the same dimensions, symmetric with respect to the center plane of the reservoir. In this way, we may take the upper half of the system alone into consideration. In contrast with

By Joe O. Ledbetter

INTRODUCTION Health physics as a profession really got a significant start during the Manhattan Project of World War 11. The Health Physics Society has recently published its 25th anniversary issue of the journal (June 1980). There was concern over radiation exposures during and after uranium production, especially about radium and its daughter products [Jackson 19401 and, as evidenced by the frequency of articles in the literature, there still is. The reason for this concern was expressed by Harley as "Workers engaged in the mining and pro- cessing of radium-bearing materials are exposed to dusts of the parent, to radon, and to the radon daughter products. In- haled radioactive particulates may be retained in the lung or redistributed to other organs of the body. Relatively minute de- posits of radioactive substances, particularly alpha emitters, have been clearly shown to be the etiological factor in a variety of injuries to industrial and re- search workers. " [Harley 1953] Emphasis in measurements has been placed on radium in water and radon in air, since these are the principal mobilized phases; however, it should be kept in mind that radium-containing particles do become suspended in air as aerosols and radon absorbs in liquids. Much of the uranium mining and production is being carried out aboveground. The principal difference between underground and surface (pit or leach) mining of uranium is the reversal in the relative importance of roles for the types of radiation dose. For aboveground the major radiation exposure is external gamma ray, whereas for underground it is internal alpha; for aboveground, the whole body penetrating is of greater importance than the lung alpha dose. AS a result of the politics involved and the law- suits for any and all diseases as being occupationally- caused, today , more than ever before, the successful performance of the activities connected with uranium production--before-, during-, and after-the-fact-- must include the provision of first class radiation protection. Such protection can be achieved by good measurements, thorough risk evaluations, and adequate controls. Meeting the ALARA (As Low As Reasonably Achievable) philosophy necessarily entails the determination of what is reasonable exposure. The necessary and sufficient elements of radiation safety under the ALARA dictum require a hard look at the dose versus effects data. There are times when the health physicist needs to make decisions of judgement rather than compliance with a well-defined regulation value. In order to facilitate such decisions, the real world must be separated from opinions that are merely artifacts of statistical variation and from the unprovable "what ifs" that are slanted to question the morality of any non-Luddite. UNITS VOCABULARY FOR DOSIMETRY There have been many radiation quantifying and dosimetric units introduced in the past. Fortunately, most of them did not catch on enough to become required knowledge for reading the health physics literature. The unit definitions necessary for our purposes here are the following: -curie (Ci)--unit of radioactivity equal to 3.7 x 10 10 disintegrations per second Webster&apos;s 19711 or the quantity of radionuclide that undergoes 3.7 x 10 nuclear transformations per second. Environmental levels of radioactivity are usually measured in picocuries (10-l2 Ci) per cubic meter for air and in picocuries per liter (pCi/~) for water and sometimes for air. .roentgen (R)--exposure dose of x or gamma rays that gives 1 esu of charge (either sign) to 1 cc of dry air @ STP. The roentgen is equivalent to an energy absorption of 86.7 ergs/g of air [Gloyna and Ledbetter 19691. .rad--radiation absorbed dose of 100 ergs per gram of absorber. The SI unit for absorbed radiation dose is the Gray; 1 Gy = 100 rads. orem--radiation absorbed dose of 1 rad times the quality factor (QF) for that radiation. The QF is 1 for x rays, gamma rays, beta rays, and posi- trons. For heavy ionizing particulate radiation, QF is a function of the amount of energy trans- ferred per unit length of travel, i.e. , the linear energy transfer (LET); the values of QF:LET in keV/um are as follows: 1:<3.5; 1-2:3.5-7; 2-5:7-23; 5-10:23-53; and 10-20:53-175 [Morgan and Turner 19 671 . For radiobiology, relative biological effectiveness (RBE) is recommended for use instead of the quality factor above that is for radiation protection: the RBE is the ratio of the dose of 200 kVp x rays to the dose of radia- tion in question (both in rads) to cause the same

Jan 1, 1980

By E. E. Carpenter

Believing that the results accomplished in the mill of the Churchill Milling Co., Wonder, Nev., during the fiscal year ended Sept. 30, 1914, will be of interest, I am presenting the more prominent facts and figures showing the progress made in treating this ore with especial reference to tonnage, supplies, costs, and extractions. The mill is situated at Wonder, Nev., in the Wonder mining district, 55 miles east from Fallon, Nev., the nearest railroad point. All supplies are hauled this distance by freight teams, this method of transportation having been found more reliable for continuous service than truclis, the price paid for hauling being slightly under one cent per pound. In this mill are treated the ores of the Nevada Wonder Mining Co. Ore is Unusually Hard The company which tested this ore before the mill was built reported "This ore is an unusually hard, tough, oxidized quartz, carrying a small percentage of high-grade sulphides, containing good values in both gold and silver. None of the rebellious silver minerals appear to occur in appreciable quantities." ... "In regard to the mill tonnage this ore is unusually hard and tough, and a high stamp duty cannot be expected. Using a 20-mesh screen and 1,050-lb. stamps, our best work was three tons per stamp per 24 hours." It is very probable that the ore delivered to the testing plant was harder than the regular mill run has proved to be. However, at present the mine is developed to a depth of 1,000 ft., and still shows hard ore in places at this depth in about the same proportion as on the upper levels from which the test ore came; during this year&apos;s work, ore was treated from nearly all levels. Together with this hard ore in the mill feed a considerable proportion appears to be broken down and tending to crumble, thus making an ideal mixture for stamp milling. A small proportion of talc is also noticeable, which sometimes increases in amount to the point where it is very troublesome in the thickeners.

Jan 1, 1916

THE book covers principally the assaying of silver and gold and the determination of these values in ores, sweepings, and base metal. It seems to have been written more for the goldsmith and jeweler than for the primary producer of metals. There were approximately sixty different substances needed in the operations described and not over a dozen different types of raw material (ore, matte, crude or alloyed metal) are mentioned. The methods of separation used were essentially simple and reasonably reliable, though the processes were not sufficiently understood to permit the selection of the simplest effective ingredients, and there was a great tendency to employ complicated fluxes, with unnecessary repetition of long-continued heatings indicative of a leisurely pace of life. Practically all the processes described are based on a few chemical facts: the inability of gold to combine with sulphur, while silver and the base metals form easily fusible sulphides; the ready oxidation of base metals; and the ii- solubility of gold in nitric acid. Fluxes serve to make earthy impurities fusible, and to carry oxidizing or sulphurizing ingredients. Many of the processes of assaying had changed little up to the beginning of the present century. Even as late as 1924, when the writer took a University course in fire assaying, the crucibles, cupels, scorifiers, molds, and tongs were identical with those of the sixteenth century, though the wind furnace had a stack on it and the muffle for cupelling was gas-fired.* The fluxes were purer, but of the same essential composition. That this branch- or twig-of metallurgy had not advanced in any funda-

Jan 1, 1949

R. G. BROWN, Bodie, Cal.: Mr. Rickard&apos;s paper, with its valuable illustrations, brings into fresh clearness the game of hide-and-seek which the miner must play with his ore-deposit; but, more than this, it goes far towards classifying those perplexing idiosyncrasies which, while unclassified, constitute a labyrinth almost without clue. Probably every engineer can add to the list by the mention of at least one fresh detail from his own experience, and I for one would like to comment on two of Mr. Rickard&apos;s divisions. To what he has written about " walls within walls" and " walls without walls," the accompanying Figs. 1 and 2 may be appropriate, the more so as they represent conditions obtaining in a part of the Butte copper-belt more typical of the copper-veins as a whole than the Gagnon, which, in some respects the most interesting mine in the camp, stands almost alone in many particulars. (See nuns., xvi., 62.) Fig. 1 was sketched in January, 1895, in the stopes above the 700-foot level of the Colusa-Parrot mine, east of the Parrot and southwest. of the Anaconda. The stope, the commercial foot-wall of which is shown at A, was 30 feet wide at this section, the pay-ore being massive chalcocite, jumbled with bornite, pyrite, quartz and thoroughly broken-down granite. A and At are inch-thick seams of black talc; B, B&apos; and B" are also talc, possibly 1/8-inch thick. In the plane of the section the "banded quartz " and " quartz and pyrite " were both of too low grade for extraction, but 5 feet back along the stope had been of fair value. The granite with quartz and bornite between Bt and A&apos; was pay-ore, but that to the right of B" was not. In both cases the ferro-magnesian minerals had been removed, leaving, where not obscured by ore, faint, dark patches. Between A&apos;

Jan 1, 1897

By W. H. Smith

IN connection with some recent work on the effect of impurities on the ductility of chromium, it appeared desirable to know the solid solubility of carbon in chromium. A literature survey indicated that this information was not available. Although considerable work has been done on the Cr-C phase diagram,&apos;.&apos; previous investigators have been more concerned with the structure and phase boundaries of the carbide phases than with the terminal solid solution. The phase diagram shown in Fig. 1 is taken from the work of Bloom and Grant&apos; and represents the most recent determination. As indicated by the dashed line, the a solid-solubility limit was not determined. Experimental Procedure Alloys of chromium were prepared from hydrogen-treated and vacuum-degassed electrolytic chromium plus spectrographic grade carbon. The oxygen and nitrogen content of the alloys was <0.002 pct. After melting, analysis of the alloys showed them to contain 0.02, 0.08, 0.15, and 0.55 pct C. Pieces of the alloys were heated in a protective atmosphere to various temperatures and then quenched after holding for a time sufficient to insure equilibrium. Microscopic examination of the as-quenched alloys for the presence of a second phase was used as a measure of the solubility limit. The heats were made in a multiple hearth arc-furnace using a zirconium-gettered static argon atmosphere. A zirconium melt was made before each Cr-C heat. Triple melting was used to insure ingot homogeneity as shown by microscopic examination. The alloys were prepared by adding portions of a 4.5 pct C-Cr master alloy to high purity chromium. The carbon contents listed previously were those obtained by analysis. The nitrogen and oxygen contents after arc melting were both <0.002 pct. Sections 1/8X1/4X1/2 in. were cut from the 100-g ingots and a hole drilled in one end in order to suspend the sample from a molybdenum wire. After the surface was carefully cleaned, a sample of each melt was hung in a mullite tube heated externally by a platinum resistance furnace connected to a vacuum system. The lower portion of the mullite tube was sealed to Pyrex and closed off several inches below the furnace. This was filled with sili-cone oil kept cold by circulating cold water around the outside of the Pyrex. Quenching into the oil bath was achieved by melting a fuse wire supporting the sample. It required about 4 sec for the sample to cool from 1400" to 600°C. This severity of quench was considered satisfactory to freeze-in the high temperature equilibrium. For tests made at temperatures of 900" to 1200°C, heating was done in vacuum; for tests above 1200°C, an argon atmosphere was used. The holding time employed ranged from 12 hr at 900°C to 6 hr at 1400°C. Experiments were performed at temperatures of 900°, 1000°, 1100°, 1200°, 1300°, and 1400°C. Microscopic examination for evidence of a second phase was done at X1500. Experimental Result The microstructures of a 0.08 pct C-Cr alloy as-cast and after quenching from 1300°C are shown in Figs. 2 and 3. A 0.15 pct C-Cr alloy quenched from 1300°C is shown in Fig. 4. The data obtained from the quenching experiments is shown graphically in Fig. 5. If the Van&apos;t Hoff equation is obeyed, a plot on a logarithmic scale of the mol fraction of solute vs the reciprocal of the absolute temperature should give a straight line. For dilute solutions the weight percentage can be substituted for the mol fraction without introducing any appreciable error. The Van&apos;t Hoff equation can then be written as where H is the heat of solution in calories per mol. The slope of the straight line on the log pct C vs 1/T plot gives the value of AH. Assuming that the Van&apos;t Hoff equation is obeyed, which is probably justified for the dilute solution of carbon in chromium, the heavy straight line shown on Fig. 5 represents the best fit of the data. This line was obtained as follows. On Fig. 5 the results of the microscopic examination of all alloys following quenching were plotted and designated as to whether one or two phases were seen. Below 1100°C all alloys showed a second phase on quenching. The heavy vertical lines shown in Fig. 5 therefore represent the possible range of the ter-

Jan 1, 1958

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By T. Cantwell, N. C. Rasmussen, H. E. Hawkes

Beryl is a mineral that may be difficult to distinguish from quartz by casual field inspection. The easily recognized green color and hexagonal crystal form of coarse-grained beryl are by no means universal, even in beryl from pegmatitic deposits. If it occurred as a fine-grained accessory mineral in an igneous rock, it would almost certainly escape detection unless samples were submitted for petrographic or chemical analysis. There may be substantial deposits of some beryllium mineral, other than beryl, that has been overlooked because that mineral also closely resembles the common rock-forming minerals. A reliable and simple method of identifying beryllium minerals and determining the beryllium content of a rock would be helpful in exploration. This article describes preliminary experiments in applying nuclear reaction to the qualitative identification of beryl and to the semiquantitative determination of the beryllium content of rock samples.

Jan 9, 1959

By R. E. Crater

Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crystallographic directions, and in materials containing quartz because of the a-ß transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 3, 1959

By W. Denham Verschoyle

IN designing a pocket instrument whereby any given horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at 1. The instrument should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrument that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this " pocket transit " attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the sight-line DCE can be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jul 1, 1907

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945