Search Documents

By D. C. Hilty, W. Crafts

L. S. Darken—Laboratory investigation of deoxidizing and other steelmaking reactions is usually centered, at least first, on the determination of the equilibrium or equilibria involved. This seems a reasonable procedure since equilibrium, if attained, depends only on composition, temperature, and pressure; hence conclusions derived from data on small experimental quantities are applicable to a heat of steel providing eauilibrium is attained in both cases. A knowledge of equilibrium serves as a useful framework even though we may know that practical conditions do not correspond to complete equilibrium. On the other hand, nonequilibrium or rate phenomena depend on a wider variety of conditions and are more difficult to interpret; conclusions applicable to laboratory conditions may or may not apply to larger scale phenomena. Hence the attainment or nonattainment of true equilibrium in the experiments here reported is of critical importance in evaluating their significance. Since some of the statements in this paper and in the closely related preceding one (on aluminum deoxidation) imply some doubt on this matter, I should first like to ask the authors whether their conditions are intended and believed to represent equilibrium. I should like to point out three considerations which seem to cast considerable doubt on the achievement of equilibrium, at least of the particular equilibrium under consideration. 1. In the experiments on manganese deoxidation the authors point out that they could not maintain the manganese-oxide slag on top of the metal in their rotating crucible, and hence they substantially dispensed with this slag. This leads to serious trouble in the interpretation of the results, for any equilibrium is, of course, a particular specific equilibrium—in this case Mn + O = MnO The experimental deletion of the upper layer of manganese oxide means that if equilibrium is attained at all it is attained between the metal and the MnO which has soaked into or adhered to the crucible (under the metal) and has dissolved substantial amounts of the crucible material including impurities. These impurities may constitute a significant portion of the slag by virtue of the small total amount of slag, even though the crucible is relatively pure. Hence there would seem to be a strong presumption that the equilibrium (if attained) involves not a pure MnO (or MnO — FeO) slag but one saturated with alumina and containing perhaps considerable impurities which substantially lower the concentration and activity of MnO, causing the above reaction to proceed to the right further than it would in the absence of alumina and impurities. Hence it is not surprising that manganese here appears as a better deoxidizer than found by other investigators. The present results may represent equilibrium with a slag of unknown composition which seems unlikely to be particularly related to plant experience. 2. The curves representing the observed silicon deoxidation (figs. 3, 4, and 5) are all drawn with a discontinuity in slope at about 0.02 pct oxygen. This point is interpreted as corresponding to the three-phase equilibrium, metal, slag, solid silica. The type of construction shown in these figures (though apparently fitting the data) is contrary to a fundamental principle of heterogeneous equilibrium as pertains to the construction of phase diagrams. According to this principle, the two solubility curves (each of the two portions of the curves in figs. 3, 4, and 5) must intersect in such manner that their (metastable) extensions must lie outside the homogeneous field rather than inside as in these figures. In other words, the "point" in these curves should be aimed in the opposite direction, if it is to be interpreted as corresponding to the three-phase equilibrium. The construction adopted is in violation of the second law of thermodynamics. This matter is discussed in detail in several texts and also by Lipson and Wilson.&apos;" The same criticism applies to the later figures representing conditions for manganese additions. The occurrence of this discontinuity or break at 0.02 pct oxygen casts further doubt on its interpretation. The earlier investigation of this system by Korber and Oelsen is in substantial agreement with the several recent findings of Chipman and coworkers that the oxygen content of iron in equilibrium with silica and silica-saturated iron oxide slag is about one third to one half that (0.24 pct at 1600") of iron saturated with pure iron oxide; thus there seems reliable evidence that iron saturated with silica and iron silicate slag at 1600" contains about 0.1 pct oxygen, or certainly much more than the 0.02 pct proposed in this paper. 3. In the quarternary system iron-silicon-manganese-oxygen one of the equilibria involved may be written 2 Mn + SiO2 (solid) = 2 MnO <slag> + Si The activity of SiO, is constant (if equilibrium is attained) by virtue of its presence as a substantially pure solid. At not too low metallic manganese content, the activity of MnO in the slag is constant by virtue of the fact that the slag is substantially pure manganese silicate saturated with silica and hence of constant composition. Thus the equilibrium constant for the above reaction is asi/a2Mn. Barring unanticipated large changes in the activity coefficients, the equilibrium constant may be adequately approximated for the composition range covered as [% Si]/[% Mn]2. Thus a plot of log [% Mn] against log [% Si] would be expected to be linear with a slope of one half as found by Kijrber and Oelsen. In the present investigation the slope (shown in fig. 15) is found to be one. It is difficult to believe that this finding represents a correct equilibrium determination, since it is at odds both with prior experimental investigation and with. theory. In view of the above points it seems that, although this paper reports many interesting findings, there is room for considerable skepticism as to the attainment of equilibrium and as to the conclusions drawn. N. A. Gokcen—The authors consider that Si% x O2% product is constant. This product is a function of the asi X a0 activity of Si02. The true constant is -------------. If the asio2 slags of this investigation were always saturated with SiO2 then Si% X O2% product would be constant,

Jan 1, 1951

By J. R. Wylie, L. C. Huntley

Drilling for oil in the eastern producing states was fairly active during the first part of 1931, although less so than in 1930. With low prices development declined during the year, until the low prices of the summer resulted in an almost complete shut-down of drilling. This coincided with the action of the Conservation Board of the Pennsylvania Crude Oil Producers Assn, in limiting pipe line runs to 50 per cent of the 1930 normal for the Bradford district and upper country, and to 70 per cent for the balance of the region. Not only was new drilling halted but in many cases oil-producing properties were shut in. In November crude prices were partly restored, and all oil offered was being taken except in the Bradford district which was restricted to 80 per cent of the 1930 normal. During the latter part of the year drilling was being resumed on a moderate scale, and new production indicated a resumption of the proration order. The interest in gas development which has been under way for several years, maintained its supremacy over the search for oil in 1931. New reserves of importance were developed during the year in the Western Kentucky Coal Basin, in the Eastern Kentucky shale gas territory, in Stark County, Ohio, as well as the Oriskany sand development in northern Pennsylvania and central New York. A gas line was completed to the Eastern Seaboard serving Washington and Baltimore, and other lines were under construction designed to serve portions of the territory not hitherto supplied with natural gas. The low price of fuel oil at seaboard is understood to be the deterrent factor against further extension of natural gas lines to these markets at present. The development of these new reserves, as well as those developed by intensive drilling in old areas, resulted in the building up of large potential gas production and a lowering of rates paid to the producer. This, coupled with the country-wide tendency to lower the consumer rates of all public utilities, resulted in a general threat to reopen rate cases before various state commissions. Oil Development The past year was marked only by the almost complete shut-down of new development, reaching its low point during the summer, with its

Jan 1, 1932

By William K. Antle

The successful application of ther mo compression lead bonding to semicondtctor or thin-film electronic devices depends on the establishment of the associated parameters. The quality of a thermocompression bond is primarily related to the process temperature and bonding force. A technique using the coelyicient of friction is presented that both reduces the time necessary for determining optimum parameter values and increases the accuracy of the results. Modern theories of the friction process are used to develop mathernatical expressions for shear and tensile bond strengths in terms of friction measurements. A further application of the pararneter-deterlnination technique concerns the measurement of surface contamination that may affect thermocompression bonding. In spite of the extensive use of thermocompression bonding, adequate methods for determining the bonding parameters have not been utilized. The quality of the weld depends on the temperature, force, and time used. There is a definite value or range of values for each parameter which assures an optimum weld. The process now generally used to obtain these values is to make several weld samples at each parametric setting, determine the mean pull strength, and relate the maximum consistent strength to optimum weld conditions. This could involve a very large number of test samples if a thorough search of each parameter were made. Experience and prior knowledge can reduce this number somewhat by limiting the investigation to a range known to contain the correct value, but the time and effort involved are still objectionable. The problems associated with thermocompression bonding of interconnecting leads to semiconductor or thin-film devices can be alleviated by the application of a new technique for establishing the process parameters. Obtaining the correct temperature, force, and duration to assure an optimum bond is accomplished by a simple measurement of the coefficient of friction. This approach increases the accuracy of parameter determination and greatly reduces the time necessary to complete the process. The approach made can be better understood by analyzing the principles of adhesion and friction on which thermocompression bonding depends. When two flat polished surfaces are placed together, the area of actual contact is much less than the apparent area determined by the over-all dimensions of the surface. This is because the microscopic surface is covered with projections which prevent uniform contact. Careful measurements of the electrical resistance across the contacting surfaces indicate the actual area may only be 1100,000 of the apparent area.&apos; Because the actual contact area is small, extremely high pressure results from moderate force. This will produce deformation and plastic flow at contact points of the microscopic projections. The process will terminate in the creation of a large number of minute welds formed at extreme pressure and cold-worked to strong, hard bonds. Load removal will generally result in fracture of most of these microbonds because of the residual elastic stresses, unless the materials are soft. Friction between metals is due to the formation and

Jan 1, 1967

By B. E. Parsons

Curtailment of production of crude oil, to the extent of effecting an approximate balance in supply and demand, was a problem confronting the oil industry in California throughout the year 1930. At the beginning of the year, with drilling operations only slightly checked, the California industry faced a steadily increasing potential production, an actual production in excess of market requirements and stocks of crude oil and refined products which had reached staggering proportions. During the year, the intensive development of the Playa Del Rey field and extensions to several oil fields, together with flush production from numerous large wells from both new and old fields, caused a steady increase in the state&apos;s potential production to a record peak in November of 1,186,000 bbl. daily. Despite the burden of this steady stream of flush production and the handicap of incomplete cooperation in several fields, curtailment successfully lowered the trend of crude oil production in California, except for the period of an open-flow test to determine actual potential production in several important fields in February. Under the curtailment programs in effect, the state&apos;s production of crude oil for the year was reduced 22 per cent. under the production of 1929 and even slightly under the production for the years 1927 and 1928. The total stocks of crude oil and refined products were reduced 2.7 per cent. during 1930, as compared to an increase of 30 per cent. in total stocks of all products during 1929. Drilling operations were reduced 28 per cent. as compared to drilling activities during 1929. Voluntary curtailment of drilling programs by many operators, particularly the major companies, accounts for the greatest portion of the reduction in drilling activity. The decline in drilling activity at Santa Fe Springs and in the east-side fields of the San Joaquin Valley was more than offset by development in new fields and extensions to deeper zones of old fields. There were 755 new wells completed during 1930, as compared to 910 completions in 1929. At the close of the year, 220 wells were drilling in the oil fields of California, 9 of which were being drilled in search of deeper producing horizons.

Jan 1, 1931

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

By George S. Rice

ARIAL maps of prospective mineral-bearing territory have become almost indispensable in all the branches of exploration, and have proved particularly useful in the great oil area of the Southwest. About nine years ago aerial photographic mapping in this area was begun. The early product was lacking in scale accuracy and other control features, which limited its effective use. Since then, the evolution of the technique of such mapping has been steady, with several mapping companies collaborating with five of the leading oil companies, and aerial maps have been prepared covering practically the entire area.Improvements in cameras, film, and developing equipment and practice have resulted in more uniform and clearer photographs, but the outstanding development has been the accuracy obtained with respect to scale and all other control features. Maps are no

Jan 1, 1936

By C. D. Cochran, F. H. Deily, M. M. White, Victor Horner

A laboratory study of the effects of physical and easily measured rheological properties upon dynamic filtration was carried out. The purpose was to determine the factors affecting dynamic filtration and thus learn how to control this important property. The recommended procedure for determining the amount of fluid loss prescribed by API Code RP 29 "Field Procedure for Testing Drilling Fluids,"&apos; is very useful for mud conditioning purposes, but inadequate for comparing filtration properties of different muds under dynamic conditions. Where dynamic filtration control becomes important for purposes such as logging and coring, other means of evaluating filtration properties are needed. A special device and testing technique were developed to provide reliable data on filtration characteristics of different fluids under dynamic conditions. Liquid saturated rock samples were drilled with a microbit, and the amount of connate liquid displaced by the fluid being investigated was measured. The empirical testing procedure was considered reliable. A large number of laboratory-prepared and field-mixed dritling fluids with a wide range of physical properties were studied. These properties included: (I) shape of consistency curves, (2) apparent viscosity, (3) plastic viscosity, (4) yield value, (5) density, and (6) API filter loss. Test results indicate that very little, if any, trend could be established between changes in these fluid properties and dynamic filtration. INTRODUCTION During the process of drilling, excessive loss of liquid from the mud to the formation is undesirable for many reasons. Filtration can reduce production-zone permeability, cause sloughing of formations, affect electric log curves, and render the fluid data obtained from cores unreliable. Thus, it is very important that we gain a knowledge of the factors that control filtration. It is generally agreed that in any type of filtration (static, dynamic, or combinations thereof), the mechanics of filtering depend in great part upon the composition of the fluid. Moreover, it is also true that the physical and rheological properties are influenced by the composition of the fluid. Indirectly, then, it was hypothesized that a relationship existed between dynamic filtration and physical-rheological properties, two effects of a common cause—fluid composition. This paper discusses an attempt to relate filtration-while-drilling to physical and easily measured rheological properties. It is believed that the results of this study may prove useful to others in the industry who are working on the problem of understanding filtration. The industry accepted practice for determining fluid loss from drilling mud is described in API Code RP 29. The practice is to measure the amount of filtrate that passes during a given interval of time from a quiescent drilling fluid under applied pressure through a piece of filter paper. This is primarily a test of static filtration properties. Other investigators have studied filtration under dynamic conditions. Williams5 and Pro-kop5 studied radial filtration and filter-cake buildup by circulating fluid through a porous cylinder under conditions similar to actual mud flow. Nowak,4 Krueger,3,4 and Vogel3 studied the effect of filtration upon permeability by flowing mud past the face of rock Samples. In their tests, the bit action was simulated by mechanical scrapers that kept the filter cake from building up. Ferguson and Klotz2 studied three types of filtration: static, dynamic, and beneath-the-bit. They investigated each type separately, using a model well in which bottom-hole hydraulics and mechanics were closely approximated.

Jan 1, 1958

By Simon T. Johnson

Potential applications for boom tunnelling machines requires reliable assessment of in-situ performance. The majority of existing classification schemes concentrate on the prediction of excavation rate, neglecting the important influence of tool consumption rates. A statistical approach is taken to the analysis of the performance data, which was obtained first-hand through in-situ monitoring, and laboratory testing of representative rock samples. A statistical discrimination technique is used to produce a scheme for the prediction of performance groups, each of which covers a limited range of cutting rate and/or tool consumption rate.

Jan 1, 1984

By Arnulf Muan, Klaus Schwerdtfeger

Equilibrium ratios C02/C0 of a gas phase coexisting with selected phase assemblages of the system Fe-Mn-0 have been determined in the temperature range 1000" to 1300°C. The oxygen pressure for the "hfnO" +hfn30, equilibrium and for the "(Fe,hTn)O" + (Fe,Mnh 0* equilibrium at high manganese contents has been determined by electromotive force measurements using stabilized zirconia as a solid electrolyte. The notstoichometry 01&apos; "hTnO" and of "(Fe, iM1z)O" solid solutions has been determined by ther-mog-/avi?netry and by wet-chemical analysis. The data obtained are used to derive activity-composition relations in "(Fe,hfn)O" and (Fe,Mn),O4 solid solutions. WUSTITE "FeO" and manganosite "MnO" form a continuous series of solid solution at high temperatures,&apos; and so do magnetite Fe304 and the high-temperature, cubic modification of Mn304 (Ref. 2) (high hausmannite, -1170). The oxides "FeO" and "MnO" are cation-deficient phases.495 The nonstoi-chiometry of "(Fe,Mn)O" solid solutions has been studied by Engell and ~ohl&apos; at two selected C02/C0 ratios at 1250°C. The two oxide end members of the spinel solid solution, FesO4 and Mn,04, however, are known to be close to stoichiometric under the experimental conditions used in the present investigation.&apos;&apos;&apos; The oxygen pressures of "(Fe,Mn)07&apos; solid solutions in equilibrium with iron have been determined by Schenck and coworkers,8 by Foster and welch," and by ~n~e1l.l&apos; The two former groups equilibrated the condensed phases in C02-CO atmospheres of lmown compositions, whereas Engell" used a galvanic cell with stabilized zirconia as a solid electrolyte. The results of these investigators are not in good agreement. Activities of FeO in manganowiistite as calculated from the results of Foster and Welch show ideal behavior, those of Engell yield a pronounced positive deviation, and those of Schenck et 01. show a moderate positive deviation from ideality. In the present work oxygen pressures for the iron + manganowiistite and manganowustite + spinel equilibria and the nonstoichiometry of manganowiistites have been measured. The data were used to calculate activities in the manganowiistite and spinel solid solutions. EXPERIMENTAL METHODS The COz/CO ratios at which manganowustite and iron are in equilibrium were determined by thermo-gravimetric and quenching methods. Experimental details are described in a previous publication.&apos;2 In the thermogravimetric technique, incipient reduction of manganowiistite pellets to metallic iron was observed as a break in the weight vs log COZ/CO curve. In the quenching technique, manganowiistite samples were partially reduced to metallic iron, or the metallic iron of manganowustite + metallic iron mixtures was partially oxidized to manganowustite, in atmospheres of constant C02/CO ratios. After quenching the composition of the oxide phase was determined by X-ray lattice parameter measurements and comparison with a standard curve obtained from oxide solid solutions of known compositions. The nonstoichiometry of "MnO" and "(Fe,Mn)07&apos; solid solutions was determined by chemical analysis of samples equilibrated in C02-CO atmospheres and quenched to room temperature, as well as thermo-gravimetrically by reducing (Fe,Mn),04 or Mn304 to manganowiistite or manganosite. The equilibrium between manganowiistite and (Fe,Mn),04 was measured thermogravimetrically by reducing (Fe,Mn),04 solid solutions having composition in the range of %„ l(NFe +NM) from 0 to 0.63. No experiments could be performed with this technique at higher manganese contents, because the equilibrium C02/C0 ratios are too large for accurate control. An additional difficulty arises at the higher manganese contents due to the strong increase in oxygen content of the manganowustite phase with increasing log Py near the manganowiistite-spinel boundary. Consequently a sharp break in the weight loss vs log C02/CO curve cannot be observed at the phase boundary. At high manganese contents of the manganowiistite, e.g., (NMn/(NF~ + NMn) > 0.9, electromotive force measurements with stabilized zirconia as a solid electrolyte were made to determine the equilibrium oxygen partial pressure. Experimental details are described in a previous paper.* Mixtures of "(Fe,Mn)O" and (Fe,Mn),04 were pressed to pellets, and the oxygen pressure of the equilibrated samples was compared to that of Ni + NiO mixtures in the cell The composition of the manganowiistite in the equilibrated two-phase mixture was determined by lattice parameter measurements and comparison with known standards. The oxygen pressure for the Ni + NiO equilibrium was taken from available data.l3~l4 No reliable results were obtained with the electromotive force technique on iron-rich oxides. The electromotive force drifted strongly with time in this composition range. An additional difficulty arises from the partial de-

Jan 1, 1968

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By John C. McDonald

The amount of published literature in the field of mechanical properties of magnesium alloys is not great; particularly with respect to rolled alloys. Haughton and Prytherchl have summarized most of the articles to 1937, including their own work on sheet. Although many papers can be found dealing with the technology of magnesium and the alloys now in commercial use, there does not seem to be any work dealing exclusively with the variation in properties of rolled alloys as caused by changes in alloy composition. Comparison of published data reveals considerable discrepancies in properties of alloys of the same composition, probably due to differences in the details of working and heat-treating followed by different workers. The purpose of this paper is to study the properties of alloys in conditions where the effects of such differences have been eliminated. It is well known that the strength and ductility of metals are functions of the working and heat-treating they have received, as well as of their chemical composition. In comparing alloys with respect to these properties, therefore, all possible combinations of the variables of the fabrication procedure ought to be carried out on each alloy. One or more of these treatments mill produce the highest ductility, or strength, or both. These highest properties would then be selected as characteristic of each alloy, and alloys would be compared on the basis of those properties. Thus a separation of the effect of composition and that of workiiig and heat-treating would be achieved. In this paper, however, a compromise with completeness has been made by carrying out a restricted number of treatments. As a consequence, the properties obtained are not necessarily the best that the alloy is capable of exhibiting; but since all alloy3 have been treated by the same method, the results ought to be comparable. The elements selected for the study comprise a class that will alloy easily with magnesium, and that are reblatively cheap. Each was added in different amounts, up to a limit that varied with the element.

Jan 1, 1940

By R. H. Lee

Without doubt, one of the most frequent and serious ani~oyailces connected with the practical running of a blast-furnace, especially in single-furnace plants, is caused by low steam, in spite of the fact that all boilers at blast-furnaces have grates for burning coal, and that coal is more or less continuously burned upon them, from three to a dozen men being pretty constantly engaged around the boilers as firemen or coal- and ash-handlers. At times, when the furnace is " tight," all available men arc put on to assist the regular firemen; yet sufficient steam cannot be got to keep the engines up to their regular number of revolutions, while the stoves, deprived of the gas which has been sent to the boilers, run cold, so that, when the furnace loosens up and resumes the regular rate of driving, the blast is very considerably below normal temperature, and a "cold," or at best a " high-sulphnr," cast is the result. Again, it often happens that a furnace, running at its best, becomes temporarily a little too hot: the pressure rises; the amount of gas made is diminished; the steam soon commences to go down; and a small scaffold is likely to form before the furnace has been brought back to the proper rate of driving, and thus enabled to take its regular amount of blast. The usual remedy is either to "jerk" the furnace by a sudden, brief intermission in blowing, or to cool the furnace by lowering the heat of the blast; but if the lower blast-temperature be maintained too long, the hearth and descending stock may be cooled below the " critical temperature" mentioned by Mr. Johnson,&apos; and the furnace may go to the other extreme, and become cold. This is especially the case when coal or coke high in sulphur is used.

Jan 1, 1907

By Joseph E. Worthington

Many thousands of years ago when our earliest ancestor first swung out of a tree, picked up a rock, and threw it at what he hoped might be his lunch, the minerals industry, in a manner of speaking, was born. It was then a very long step indeed to the primitive metal industry of our early civilizations, for we know that precious metals were accumulated and some metal objects were produced several thousand years ago. Prospecting, or "exploration" to use the modern euphemism, consisted of little more than outcrop examination and the use of a gold pan, and it probably did not change much from our earliest civilizations until relatively recent times. In a general sense, all the early explorers of North America were also prospectors, for mineral wealth was certainly one of the goals of the first pioneers and settlers. The earliest pioneers didn&apos;t do too badly either, for they discovered copper and iron in various places in the Appalachians and Michigan, gold in the Southeast Piedmont and many mineralized areas in the Southwest. In most places these were outcropping ores or gossans, and the prospecting was incidental to the arduous task of ekeing out a living in a new land. It was the explosive discovery of rich placer gold deposits at Sutter&apos;s Mill in California that caught the public fancy and precipitated the establishment of prospecting as a full-time occupation. After the end of the Civil War in 1865, full-time prospecting became an important occupation and continued as such for almost three generations. Prospectors equipped with picks, shovels, gold pans and four-footed transportation swarmed all over what are now our Western States, discovering thousands upon thousands of mineral showings-and certainly most of today&apos;s large mining districts. Our vigorous western mining industry is a tribute to the courage and persistence of these men. The techniques of these picturesque prospectors, however, were essentially the same as those of their predecessors-examination of every outcrop and assiduous use of the gold pan. The great increase in discovery at this time was therefore due to increased activity rather than to different techniques. An important result of this in- creased prospecting was the growth of interest in geology. It was during this period that the U.S. Geological Survey began to grow. Many of the major mining districts were mapped, and geological studies and projections began to have an impact on further ore discovery. Ore search and development gradually became more geologically oriented and the geologist became a fixture in most mining camps by the 20th century. The development of mass-mining techniques in the early part of the century also changed exploration concepts.

Jan 1, 1971

By Noel Stearn

WHEN the Age of Machinery was suddenly thrust upon civilization about the beginning of the nineteenth century, an unprecedented demand for mineral resources sprang up. This demand brought about the rapid development of the known ore deposits and the discovery of such other deposits as could be encountered by energetic and canny pros-pectors. Thus in the countries now reasonably ac-cessible nearly all orebodies have been located except those which are totally concealed even from the eyes and "senses" of experienced and expert prospectors. The high rate of exhaustion of known ore deposits and the necessity of looking farther and farther ahead for raw materials as a matter of insurance on the stu-pendous capital outlays involved in mining, develop-ment, and conversion operations, have resulted in excep-tional activity in three different fields of effort. The first is purely geographic. Prospectors are now pene-trating the few hitherto inaccessible regions in the hope of stumbling upon exposed ore deposits or locating visible indications of their presence. The second is chemical. Industrial chemists and metallurgists are seeking to facilitate the exploitation of lower grade ores to find methods of recovering valuable metals from common substances. In the third field of effort. lie the activities of the economic geologist and the mining engineer, who en-deavor to locate concealed ore deposits, which would remain hidden from the prospector, no matter. how expert or conscientious he might be. Obviously the task which such a man must face is both exacting and indefinite, and the tools which he has heretofore been permitted to bring to it are, for the most part, abstract-a knowledge of certain fundamental princi-ples and processes involved in the origin, occurrence, structure, and distribution of deposits. of natural re-sources and of the rocks which form the environments of those deposits, and a process-of reasoning by analogy supplemented by the .use of the diamond drill, or such artificial exposure as the test pit, trench, shaft or tunnel. His primary efforts are usually bent on acquiring a knowledge of the distribution of the rocks-as accurate -is possible-which is a natural prerequisite to any conclusion as to how they became so distributed. Over very extensive areas, however, he meets. the extreme difficulty of being unable to see the rocks, except at rare intervals, since .they have been concealed by an overburden of glacial material, of alluvium, of soil, or of other rocks.

Jan 9, 1928

By F. Keller, E. H. Dix

The desirable high strength and hardness of the heat-treated strong aluminum alloys result from two distinct structural changes: (1) the formation of a solid, solution by heating at the required temperature for a sufficient period, and the substantial retention of this solid solution by rapidly quenching; (2) precipitation of particles of constituent and coalescence to a critical size to produce maximum strength and hardness. In alloys of the duralumin type, that is, alloys containing both copper and magnesium silicide precipitation takes place at normal atmospheric temperature, whereas in alloys containing copper without magnesium silicide or magnesium silicide without copper, maximum properties are obtained only after an accelerated aging treatment consisting of heating for 15 to 20 hr. at temperatures of about 150" C. The mechanical properties of these alloys subsequent to quenching but prior to aging are ideal for forming operations. Unfortunately, however, the alloys of the duralumin type age very rapidly during the first 24 hr. and aging is substantially complete after four days. For severe forming, such as the heading of rivets, it is desirable that this be accomplished within ½ hr. or at the most 2 hr. after quenching. Alloys containing magnesium silicide without copper also age at normal temperatures but the aging is less rapid and the material can be satisfactorily worked within several weeks after quenching. Some slight aging of alloys containing copper alone also takes place at room temperature but it is unimportant from the standpoint of workability. Any method of retarding the aging at room temperature of the duralumin type of alloys would be of considerable advantage in that the period during which the material could be worked successfully would be lengthened. For instance, in aircraft plants it is customary to supply the workmen with small lots of rivets that should be used within ½ hr . after heat treatment. Such procedure has the obvious disadvantage of being uneconomical, and furthermore there is always the possibility that the workmen would use the rivets after the time limit had expired, or the supply being depleted might use some that had not been heat-

Jan 1, 1931

By L. S. Panyity

The question of natural-gas supply is receiving careful consideration in many parts of the country, as in the winter months it is quite a problem to have on hand sufficient gas to satisfy the demand. Increasing the output of wells by the application of vacuum has been tried with various results and large companies have attempted to keep up the supply with gas compressors. The possibility of storing natural gas in the sands of exhausted gas pools has been tried in a few instances with satisfactory results. This method may prove of practical value in solving the problem, especially in the case of towns that formerly obtained gas from their immediate vicinity, but now must search for new pools. Town Plant Regulator High Pressure Line Exhausted Gas Field used for Storage Producing Gas Field FIG. 1. In all cases, only part of the available supply is utilized during the warns weather, so that many wells are shut-in, yet during the winter months, the supply is not sufficient even with all the wells on the line; in such cases it would be of great value if a large volume of stored gas were on hand, obtained through wells that would have been standing idle during the summer.

Jan 1, 1919

By O. C. Ralston, William C. Hunter

DUring experimental study on the separation of a zinc concentrate from the heavy sulfide ores of Jerome, Ariz., a great deal of attention has been given to proper activation of the sphalerite content of the ore. The sphalerite at Jerome contains enough iron to class it as a marmatite, as picked specimens have only about 60 per cent. zinc, whereas pure zinc sulfide contains 67 per cent. zinc. This marmatite in large pieces is black in color, but in dry powdered state is brown. A flotation froth made from it has a silvery black luster in comparison with a brassy luster caused by chalcopyrite which occurs in the same ores. The sample used in most of the experiments described below consisted of about 3000 Ib. of diamond-drill core from the zinc-bearing orebodies of the United Verde mine, and had the following analysis: Per Cent. Per Cent. Oz. peR Ton Cu............... 0.695 Al2O3............ 0.83 Ag................. 1.30 Zn............... 6.17 S................ 43.35 Au................ 0.02 Fe...............36.23 CaO............. 0.46 SiO2............. 9.27 Mineralogically, this analysis is calculated to the following, which is in agreement with the microscopic examination: Per Cent. Per Cent. Chalcopyrite................... 2.0 Schist........................... 3.2 Marmatite..................... 10.32 Quartz........................... 8.2 Pyrite........................ 73.0 Calcite.......................... 0.9 All samples were ground in a laboratory ball mill in order to leave about 3 per cent. on a 200-mesh sieve, fine grinding being essential to liberate the minerals in the ore. Most of the Jerome ores are so intimately crystallized that reasonably complete unlocking by grinding does not take place until 800 mesh is approached. Therefore, the 200-mesh grind adopted contains a considerable amount of locked mineral grains, but not so much as to render impossible the preparation of commercial grades of concentrate.

Jan 1, 1930

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

By Perry G. Harrison

The increased use of sintering for the beneficiation of iron ores and the reclaiming of flue dust creates a lively interest in sintering costs and economics. The character of material sintered and geographical location of plants so radically alter sintering costs and economics that it is well.to understand at least the basic elements which control such changes. The following cost factors are believed to be roughly approximated for large-scale Dwight-Lloyd continuously operated sinter-machine installations located anywhere. Per Crude Ton Labor, supplies and repairs 0.15 Power 6.5¢ X kw-hr. rate ? Plant overhead and administration 0.05 Depreciation per ton annual capacity 0.05 Fuel: 6 per cent coke breeze or equivalent minimum ? 1 per cent coke breeze additional for each 5 per cent free and combined water in ore or dust ? Ignition distillate at 0.6 gal. per ton ? Per Sinter Ton Royalty on ore 0.10 Royalty on flue dust 0.15 Per Crude Ton "Winter expense"; i. e., the cost of the five months enforced idle . period for plants tied in to Great Lakes transportation season 0.03 Using the foregoing data, it is possible to roughly approximate the cost of efficient sintering at any location for any ore, viz: Per Crude Ton Per Ton Handled Sinter 1. Flue Dust—Steel Plant Locations Sinter recovery, 15 per cent moisture and carbon 85 per cent Labor, supplies and repairs 0.15 0.18 Power 6.5¢ X 1¢ kw-hr. 0.065 0.08 Plant overhead and administration 0.05 0.06 Depreciation per ton 0.05 0.06 Dust handling and preparation 0.10 0.12 Fuel: free, contained in dust Ignition: blast-furnace gas free Royalty 0.15 Total $0.65 Note:—Cost increased by either deficiency or considerable excess of carbon in dust.

Jan 1, 1932

By C. H. Curtis

HE valuable mineral content of the current feed -*- to the Miami concentrator is as follows: copper, 0.7 pct total; molybdenum, 0.01. Flotation of this ore yields a sulphide concentrate containing: chalco- cite, 44 pct; molybdenite, 0.5; pyrite, 50.0; insol, 5.5. A combination of potassium ethyl xanthate and pentasol amyl xanthate as collectors, and pine oil as frother, are used in this flotation. Rejection of pyrite is encouraged by holding the amount of collectors used to the minimum consistent with copper recovery and by operating at high alkalinity (equivalent to 0.35-0.40 lb CaO per ton solution of pH 11.0). The molybdenum recovery in the sulphide concentrates under the above flotation conditions is approximately 50 pct of that originally present in the ore. Taking into account the acid soluble molybdenum, indicated molybdenite recovery is 75 to 80 pct. The attempt to separate the molybdenite into an acceptable molybdenum product begins with the bulk sulphide flotation concentrate just described. This concentrate is composed of chalcocite, whose floatability has been promoted to the fullest extent possible for the sake of its recovery from the ore, together with the pyrite which has been activated along with the copper mineral. The problem is to deaden the copper and iron minerals, and to float the molybdenite. Obviously in the accomplishment of this end, conditioning and preparation of the pulp, prior to flotation, plays an all important role. The first step is thickening to 50 to 60 pct solids, with milk of lime added to the thickener feed to maintain an alkalinity of the pulp equivalent to a pH of 8.5 to 8.8 during its residence in the thickener. The purpose of the thickening is primarily to reduce the volume of pulp for subsequent treatment. However, the relatively prolonged retention of the pulp in the thickener at the desired alkalinity is known to have a favorable depressing effect upon pyrite. There is a limit for this alkalinity above which a depressing effect upon molybdenite occurs. The thickened pulp (alkalinity: 0.015 lb CaO per ton, pH 8.8), discharges into an agitator, retention time approximately 2 hr, to which additional lime is added to raise the alkalinity to 0.35 to 0.40 lb CaO per ton solution, pH 11.6. This additional lime is required for pyrite depression and can be tolerated without loss of molybdenite because of the limited time of contact in the conditioner tank. The pulp leaving the lime conditioner passes through two successive steaming tanks, which are mechanically agitated, and into which live steam is admitted directly into the pulp near the bottom of the tanks. The temperature of the pulp is maintained as near boiling as possible. The steaming time is approximately 4 hr. The pulp leaving the last steamer has an alkalinity of about 0.04 lb Cao per ton solution, pH 8.7. It is believed that oxidation of the copper and iron sulphides occurs during steaming, the resulting sulphates reacting the calcium hydroxide to calcium sulphate and thus reducing the alkalinity. Since the steamer-feed solution is already saturated with calcium sulphate, the calcium sulphate produced during steaming is precipitated. It is believed that this calcium sulphate is precipitated preferentially on copper and iron mineral surfaces thus decreasing their floatability. Aside from the "lime chemistry" during steaming, pine oil is displaced from the pulp and xanthate decomposed, which has a major effect upon the deadening of the copper and iron sulphides. Following steaming, the hot pulp is admitted to another conditioning tank wherein it is aerated, primarily for cooling, but incidentally for additional oxidation of the copper and iron sulphides. The resulting "deadened" pulp is then diluted to 20 pct solids, a specific collector for molybdenite, ordinary stove oil, is added and the separation of the molybdenite by flotation is undertaken at a pH of 8.5 to 8.8 in standard Miami air-flotation ma-chines. B-22 frother is used when necessary. A re-grind of the thickened rougher concentrates is made prior to the first cleaning operation chiefly for rejection of insoluble in subsequent flotation. The cleaner concentrate is then stepped up to 90 pct MoS, in an 8-cell Denver flotation machine No. 18. Sodium silicate is added to the cleaner circuit. Its effect is to flocculate molybdenite and stabilize the froth. In summary, it may be stated: 1. Separation of molybdenite into an acceptable product from sulphide copper concentrates by flotation involves preliminary preparation and conditioning of the pulp, which is of major importance. 2. This preparation and conditioning consists of several successive steps: (A) Thickening to 50 to 60 pct solids at controlled alkalinity to reduce volume of pulp and to contribute to depression of pyrite. (B) Agitation at high-pulp density for limited time with additional lime to provide for depression of pyrite. (C) Steaming at high-pulp density for decomposition of xanthate and xanthate surface films, evolution of pine oil, and oxidation of sulphide minerals other than molybdenite. The latter involves sulphating of lime with probable precipitation of calcium sulphate preferentially on copper and iron minerals. (D) Aeration at high-pulp density for cooling, and for further oxidation of copper and iron sulphide minerals. (E) Dilution of pulp to 20 pct solids and addition of specific collector for molybdenite, common stove oil. It is hardly necessary to point out that this rather drastic procedure for depression of previously activated copper and iron sulphide minerals, without at the same time depressing molybdenite, is possible due to the inherently high floatability and refractory nature of molybdenite. However, molybdenite is susceptible to depression by excessive lime which must therefore be limited to the amount consistent with satisfactory molybdenite recovery. The steaming procedure is being carried on at Miami Copper Co. under license agreement with Janney, Nokes, and Johnson, holders of letters patent on the process.

Jan 1, 1951