Search Documents

Using 5-p Ni powder and 0.018 ,u A1203, oxide dispersion strengthened nickel alloys were prepared by mechanical mixing of powders, followed by compaction, sintering and extrusion. Processing variables such as cooling of the powder during mixing, electrostatic discharging, mixing time, amount of oxide, and so forth, were studied to determine the effects on room-temperature tensile and high-temperature creep-rupture properties and on the reproducibility of alloys. MECHANICAL mixing of metal and metal oxide powders provides one of the simplest and most inexpensive methods for preparing dispersion strengthened metal-metal oxide alloys;" however, because of large differences in specific gravity, powder particle diameters and other variables, difficulties have been encountered in reproducing alloys and alloy properties. Using 5-p Ni powder and 0.018 p A1203, the following variables were investigated: a) Blending techniques b) Blending time c) Volume fraction of oxide for the selected pow- ders d) Sintering of compacts before extrusion Cooling of Powders During Blending— Cremens and Grant had indicated that dry ball milling of the powder mixture gave superior results over other procedures. When ultra-fine metal and oxide powders became available and comminution was unnecessary or offered little gain, the use of dry mixing in a Waring Blendor gave optimum results.' In the current study, observations of the powder mixtures indicated that considerable heat was generated due to the high speed of the Waring Blendor (15,000 rpm). This heating appeared to produce some degree of clustering and pelletizing. To minimize such agglomeration, a Pyrex cooling coil was installed in the mixing vessel. A double coil, water cooled, proved to be quite satisfactory, providing a fair degree of cooling along with good erosion resistance. Discharge of Electrostatic Charge—Electron-microscopy showed that agglomeration was minimized by the cooling procedure but was not entirely eliminated. It appeared that some of the ag- glomeration had to be explained on the basis of an electrostatic attraction due to the high-speed blending operation. These charges had the effect of promoting the growth of alumina clusters. At the end of the blending procedure such clusters had an effective size which was as much as 50 times that of the individual powder particles and were very tightly bunched. Several methods were utilized to try to discharge the electrostatic forces to minimize the clustering. One successful method, utilized in alloy 17, involved continuous exposure during blending to a radium source of 50 millicuries at a distance of 1.5 ft from the container. A number of other methods were noted to work equally well. Fig. 1 shows the more open oxide structure which results from such a treatment, permitting the matrix metal to penetrate into the cluster more effectively. The combination of powder cooling and discharging led to noticeably improved structures. Fig. 2 shows a cross and a longitudinal section in alloy M-17, one of the best alloys, illustrating the marked decrease

Jan 1, 1961

By Henry S. Drinker

(Canal Zone Meeting, November, 1910.) FEW men reach middle life without having had the experience of failure in one or more undertakings; and most of us can look back with gratitude to help or advice given us by friends at critical periods of our lives. If, as men, we ask and take the benefit of such aid, why should we expect our sons to be stronger? A parent can make no greater mistake than to send a boy, however steady and intelligent he may be, off' to school or college, and expect the boy always to cope successfully with all the new conditions and new difficulties that may confront him. This is undoubtedly more the case with a freshman, in his first year at college, than in later years, or than it is with a boy at day- or boarding-school, where the boy receives a greater degree of care and oversight than can be given to the young man entering college; of all periods in life, the youth in his freshman year-fresh from the overshadowing care of home and school-may need judicious advice and timely aid. The change from the restraint of home and school to the freedom of college life is sudden and marked, and it is in this the first year of the boy or young man of 17, 18, or 19 years of age, that some tactful, judicious aid should be near him in his work and course. Some boys go to college so well prepared that they become careless and finally fall behind in their work from over-confidence. Others meet trouble from ambitiously trying to do more than their previous preparation, or physical or mental strength, can sustain. Others fall behind from illness-from injuries-from natural inability to grasp at first, without more aid than comes to them in the regular course of instruction, the higher mathematics-or mayhap the modern languages, or other subjects presented by the advanced curriculum of the present day. When a boy or youth begins to

Jan 1, 1911

By Robert F. Calman

OUTLINE FIVE EXAMPLES OF GOLD-LINKED FINANCINGS 1. Financing the Lupin Mine • Sale of Cdn $40.0 million of 12% preferred shares and Cdn $40.0 million of Gold Purchase Warrants @ $595 per ounce. 2. Financing the Copper Range acquisition • Borrowing 100,000 ounces from a Canadian chartered bank @ US$307 for five years. 3. Financing the Round Mountain expansion • Borrowing up to US $80.0 million in dollars, convertible into gold, repayable over five years from a group of North American banks. 4. Financing the Tenneco Precious Metals Division acquisition •Sale of SFr 110.0 million of ten year 3-718% bonds with warrants to buy 132,000 ounces of gold at US $560. 5. On Forward Sales, Puts and Calls • Gold, Silver, Canadian Dollars, Swiss Francs THE FINANCIAL RULES AT ECHO BAY 1. Never bet the company 2. Equity is the primary form of capital for a gold mining company 3. On debt 4. The Yardsticks for Corporate Decisions 5. Financial Community Relationships 6. Dividend Policy No Text Available Tables Follow

Jan 1, 1990

By H. V. Churchill

There are two distinct methods of combating corrosive conditions. The first and most popular method is to choose a surface or material which will give adequate service under the specific and general conditions which are present. The second is a control or modification of the corrosive conditions to the end that metals and materials which would be attacked and corroded without such control or modification may be used. Under the first method of attack of the corrosion problem may be grouped such devices as the selection of metals or alloys which offer great resistance or the use of protective coatings such as paints, lacquers or metallic coatings. Such procedures are exceedingly useful. It is undoubtedly true that most of the problems of corrosion will be solved by recourse to this first method of attack. However, it must be remembered that there are many conditions in which metals are used where the choice of the particular metal to be used must depend upon other factors than corrosion behavior. Some of the factors which may govern the selection of metals for specific use are the physical and mechanical properties of the metals. But there is another factor which is of prime importance and that is relative price. It is the pressure of these factors of mechanical properties, physical characteristics, and relative price that has acted as the stimulus for the second methhod of combating corrosion. The producer and user of various metals is confronted with the fact that because of mechanical properties, physical characteristics, or price, the use of a particular metal is desirable even though the corrosion conditions are adverse to the use of the metal. In many cases, the successful use of the metal may be made even though it is impossible to protect the metal by coatings. This is rendered possible by control or modification of the corrosive media. Use of Sodium Silicate to Prevent Attack by Alkali Solutions This idea of controlling or modifying corrosive media is well illustrated by some recent experiences with aluminum. For a number of years collapsible tubes have been made of aluminum. Due to the ease with which aluminum is attacked by even mild alkalies, the use of such tubes

Jan 1, 1929

By H. V. Churchill

There are two distinct methods of combating corrosive conditions. The first and most popular method is to choose a surface or material which will give adequate service under the specific and general conditions which are present. The second is a control or modification of the corrosive conditions to the end that metals and materials which would be attacked and corroded without such control or modification may be used. Under the first method of attack of the corrosion problem may be grouped such devices as the selection of metals or alloys which offer great resistance or the use of protective coatings such as paints, lacquers or metallic coatings. Such procedures are exceedingly useful. It is undoubtedly true that most of the problems of corrosion will be solved by recourse to this first method of attack. However, it must be remembered that there are many conditions in which metals are used where the choice of the particular metal to be used must depend upon other factors than corrosion behavior. Some of the factors which may govern the selection of metals for specific use are the physical and mechanical properties of the metals. But there is another factor which is of prime importance and that is relative price. It is the pressure of these factors of mechanical properties, physical characteristics, and relative price that has acted as the stimulus for the second methhod of combating corrosion. The producer and user of various metals is confronted with the fact that because of mechanical properties, physical characteristics, or price, the use of a particular metal is desirable even though the corrosion conditions are adverse to the use of the metal. In many cases, the successful use of the metal may be made even though it is impossible to protect the metal by coatings. This is rendered possible by control or modification of the corrosive media. Use of Sodium Silicate to Prevent Attack by Alkali Solutions This idea of controlling or modifying corrosive media is well illustrated by some recent experiences with aluminum. For a number of years collapsible tubes have been made of aluminum. Due to the ease with which aluminum is attacked by even mild alkalies, the use of such tubes

Jan 1, 1929

By C. W. Binckley, F. R. Burgess, E. R. Haymaker

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By D. T. Peterson, T. Carnahan

The diffusion coejTicients of carbon, nitrogen, and oxyget were determined in $ thorium over the tempernilcre range 1440" io 1715°C. The diffusion coyfiicir?zls are given by: D = 0.022 exp (-27,000/RT) jor carbo)~, D = 0,0032 exp(-l7,00Q/RTj for nitrogen, and D = u.0013 expt(-11,UOU/RT) for oxygen. Cavl~orz was found to increase the hardness of thoriunz nearly linearly with concentration over the range 100 to 1000Ppm carbon. ThORIUM has a fcc structure up to 1365°C and a bcc structure from this temperature to its melting point at 1740°C. Diffusion of carbon, oxygen, and nitrogen in bcc thorium was of interest in connection with the purification of thorium by electrotransport.' In addition, it was possible to measure the diffusion of all three of these interstitial solutes in the same bcc metal. Only in niobium, tantalum, vanadium, and a iron have all three interstitial diffusion coefficients been measured in a given bcc metal. Diffusion coefficients have been measured for carbon and oxygen in a thorium by Peterson2, 3 and for nitrogen by Gerds and Mallett.4 Activation energies for diffusion are reported by the above authors to be 38 kcal per mole for carbon, 22.5 kcal per mole for nitrogen, and 49 kcal per mole for oxygen. Values of the diffusion coefficients of carbon and nitrogen in 3 thorium have been reported by Peterson et al.' However, these were secondary results of their investigation of electrotransport phenomena in thorium and it was hoped that the present study could provide more precise data. EXPERIMENTAL PROCEDURE The specimens used in this study were the well-known pair of semi-infinite bar type. The couple was formed by resistance butt welding two 0.54-cm-diam by 3.0-cm-long bars of thorium together under pure helium, the concentration of the solute being greater in one cylinder than that in the other. The finished couple then contained a concentration step at the weld interface and diffusion proceeded only along the axis of the rod. The thorium used in this study was prepared by the magnesium intermediate alloy method.5 The total impurity content was less than 400 ppm. The major impurities were: carbon, 100 ppm: nitrogen, 50 ppm; and oxygen. 85 ppm. The total metallic impurity content was less than 150 ppm. The high solute concentration portions of the diffusion couples were prepared by adding the solute to the high-purity thorium in a non-consumable electrode arc melting procedure. Carbon and nitrogen were added in the form of spectroscopic graphite and nitrogen gas while a Tho2 layer was dissolved by arc melting to add oxygen. High-purity thorium formed the low concentration portions in the carbon and nitrogen couples. The low oxygen portions were obtained by deoxidizing high-purity thorium with calcium for 3 weeks at 1000°C according to a method reported by Peterson.3 The high C-Th contained 400 ppm C, the high N-Th contained 400 ppm N, the high 0-Th contained 220 ppm 0, and the low 0-Th contained 25 ppm O. The high O-Th was brine-quenched from 1500°C to retain most of the oxygen in solution at room temperature. These concentration levels were all below the solubility limits in 0 thorium at 1400°C. A resistance-heated high-vacuum furnace was used to heat the couples. The samples were mounted horizontally on a tantalum support which had small grooves near each end. Spacer rods of thorium, 0.4 cm in diam, were placed in these grooves to prevent contact between the sample and the tantalum support. This arrangement should have prevented contamination of the sample by contact with the support. In further effort to reduce contamination, the oxygen diffusion couples were sealed inside evacuated outgassed tantalum cylinders lined with thorium foil. Thorium rings around each end of the samples acted as spacers in this case. Pressure during diffusion runs was about 10-6 torr after an initial outgassing stage. Temperature measurements were made by sighting on black body holes in the sample support adjacent to the samples with a Leeds and Northrup disappearing-filament optical pyrometer. Temperatures were constant during a diffusion anneal to ±5C. The observed temperatures were corrected for sight glass absorption after each diffusion run. The pyrometer was checked against a calibrated electronic optical pyrometer and a calibrated tungsten strip lamp with the electronic pyrometer being taken as the standard. All temperature readings agreed to within ±3C over the temperature range 1450" to 1690°C. Time corrections due to diffusion during heating and cooling were necessary because of the short diffusion times. The diffusion times ranged from 6 min for the oxygen sample run at 1690°C to 90 min for the carbon sample run at 1500°C. A series of temperature vs time plots were made for heating and cooling of the samples to the various diffusion temperatures. This data was then used in a method according to shewmon6 to determine the time corrections. The corrections amounted to

Jan 1, 1970

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Robert L. Frantz

Progress and improvement continue to be the bywords of a dynamic coal industry. The industry continues to gain strength and expand its horizons in the face of competition from atomic energy and the problems of restrictive legislation. The direct contribution of coal mining and transportation to the national economy is about $3 billion a year ac- cording to a study made by the National Coal Policy conference. Coal remains the backbone of the power industry producing almost two-thirds of all the electrical energy generated by fossil fuels and one-quarter of all the energy consumed in the nation. Power supplied by electric utilities increased 6.9% last year. The chairman of the Federal Power Commission predicted a 7.5% growth rate until 1980 for the nation's electric output. Some 80,500 MW of fossil fired power plant capacity are on order or under construction before 1974, compared to a present capacity, all sources, of about 290,000 MW. The comparable new additions of nuclear power plants is expected to total about 51,000 MW.

Jan 2, 1969

By John V. Beall

Monotonous flood planes flanked either side of the road as we drove in the embassy car from the airport to downtown Seoul. We crossed the brown waters of the Hann River, meandering over mud flats. A great, gnarled tree bore beautiful fall colors of gold. "That is a Ginko Tree, the oldest living fossil, probably a hundred million years old;" said Jean W. Pressler. Compared to other cities of the Far East, the traffic in and around Seoul was sedate. Few motorcycles or bicycles, and little superfluous horn tooting. "This is the best season in Korea. We have long beautiful springs and falls," said Pressler, chief of the mining branch of USAID, and he continued with a briefing on the country.

Jan 8, 1969

By W. Geo. Waring

THE growing need of better methods for the recovery of zinc and other elements from complex sulfide ores has suggested an inquiry respecting a possible group separation of the elements by the aid of volatilization at more or less elevated temperatures. It 'is evident that if the zinc content of such ores can be completely separated, for instance, as pure oxide, by a volatilization 'method, there should be no difficulty in recovering the other elements by smelting and refining. Zinc burning" as applied to zinkiferous ores has advanced but little in practice since the invention of the wetherill grate-furnace process in 1852, as may be seen by reference to papers on the subject.' In other words the thermochemical reaction employed in effecting the volatilization of the zinc is essentially one of reduction by means of carbon, whether the ores treated contain their zinc in an oxidized form, or as the sulfide. The zinc vapors, liberated from the ores at a temperature above that required for the reduction of ZnO by C (about ,1100° C.) or for the volatilization of ZnS per se, (about' 1300°-1400° C.) are subsequently burned to ZnO or to ZnO + SOz, by contact with' atmospheric ,oxygen in the upper or posterior parts of the furnace chamber, or in a so-called "combustion chamber" after leaving the .furnace proper.

Jan 1, 1925

By Paul R. Cook

The ore deposit of the Buckhorn Mines Co., Buckhorn, Nev., is peculiar in being a shallow kaolinized mass of material with basalt walls, and having apparently no direct connection with any of the usual gold-bearing rocks. The average ore contains 16 per cent. water of hydration, and the cyaniding of this hydrous clayey material offered unusual difficulties as compared with an average Nevada quartz ore. The orebody was thoroughly developed; then the mill was built according to the latest cyanide practice, with such changes as were thought to be demanded by the peculiar nature of this ore. Upon starting the mill, the ore proved more difficult to handle than had been anticipated. It is hoped that an account of how these difficulties were met may prove of interest to anyone having a clayey ore to handle and to the profession in general. Geology The Buckhorn orebody lies along a north and south fault plane of perhaps 1,000 ft. dislocation, that can be traced for miles; but the only other known mineralization consists of similar ore in the Murphy mine, a mile farther north. The east or hanging wall is hard and smooth, being a typical fault plane. The best ore is along this wall, gradually grading down toward the west until at 30 to 60 ft. it is too low-grade to mine. The country rock on the west consists of alternating layers of hard and soft basalt and basalt scoria, pitching toward the mine. One of these basalt layers on the hillside a little above the mine is marked, for 3 or 4 miles in length, by a line of springs which seep out along it. Perhaps the meeting of the surface drainage, passing down these basalt layers, with the fault-plane solutions explains the formation of the Buckhorn orebody.

Jan 1, 1917

By Charles E. Lundin

The character of the Er-D system was established by determining pressure-temperature-composition relationships. A Sieuerts&apos; apparatus was employed to make measurements in the temperature range, 473" to 1223"K, the composition range of erbium to ErD3, and the pressure range of 10~s to 760 Torr. The system is characterized by three homogeneous phase regions: the nzetal-rich, the dideuteride, and the trideuteride phases. These phases and their solubility boundaries were deduced from the family of isotherms of the system zchich relate the pressure-temperature-composition variables. The equilibrium plateau decomposition relationships in the two-phase regions were determined from can&apos;t Hoff plots to be: The differential heats of reaction in these two regions are AH = - 53.0 * 0.2 and -20.0 *0.1 kcal per mole of D2, respecticely. The differential entropies of reaction are AS = - 36.3 * 0.2 and - 31.0 * 0.2 cal per mole D2. deg, respectively. Relative partial molal and intepal thermodynamic quantities were calculated from the pure metal to the dideuteride phase. The study of the Er-D system was undertaken as a logical complement to an earlier study of the Er-H system.&apos; The primary interest was to compare the characteristics of the two systems and relate the difference to the isotopic effect. Studies of rare earth-deuterium systems by other investigators have been very limited in number and scope. Furthermore, there is even less information available wherein an investigator has systematically compared a binary rare earth-hydrogen system with the corresponding rare earth-deuterium system. The available information consists primarily of dissociation pressure measurements in the plateau pressure region of a few rare earths. Warf and Korst&apos; determined dissociation pressure relationships for the La- and Ce-D systems in the plateau region and several isotherms for each system in the dideuteride region. They compared these data with those of the corresponding hydrided systems. The study of these systems as a whole was very cursory and did not give sufficient data for a thorough comparison of the effect of the hydrogen vs the deuterium in the respective rare earths. The heat capacities and related thermodynamic functions of the intermediate phases, YH, and YD2, were determined by Flotow, Osborne, and Otto,~ and the investigation was again repeated for YH3 and YD3 by Flotow, Osborne, Otto, and Abraham.4 This investigation studied only these specific phases. Jones, Southall, and Goodhead5 surveyed the hydrides and deu-terides of a series of rare earths for thermal stability including erbium. They experimentally determined isotherms of selected hydrides and plateau dissociation pressures for deuterides. These data allowed comparison of the enthalpy and entropies of formation of the dihydrides and dideuterides. To date, no one rare earth has been selected to thoroughly establish the complete pressure-temperature-composition (PTC) relationships of binary solute additions of hydrogen and deuterium, respectively. The objective in this investigation was to provide the first comparison of a complete family of isotherms of a rare earth-deuterium system with those of a rare earth-hydrogen system. This would allow one to determine what differences exist, if any, in the various phase boundaries and the thermodynamic relationships in various regions of the systems. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure deuterium, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GMl00A and a CVC, GM110). Pure deuterium was obtained by passing deuterium through a heated Pd-Ag thimble. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit deuterium to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to . An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to k0.5 Torr and in the McLeod range (10~4 to 10 Torr) to *3 pct. The deuterium compositions in erbium were calculated in terms of deuterium-to-erbium atomic ratio. These compositions were estimated to be *0.01 D/Er ratio. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9+ pct. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<i vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the PTC relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 gr for each loading of the reaction chamber. The procedure employed to obtain the PTC data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen

Jan 1, 1969

There were present eleven Directors, the Institute&apos;s Legal Counsel, the Secretary, the Assistant Secretary, and twenty-three guests. The Report of the Committee on Nominations (listed elsewhere) was presented and ordered to take the statutory course. The appointment of a Committee on Mine Taxation was approved. An Advertising Manager was appointed. E. G. Spilsbury and A. S. Dwight were appointed as representatives of this Institute on the Franco-American Engineering Committee. The Transactions were presented to the University of Louvain, and the monthly Bulletin to the French Technical Index. Permission was given to publish in full the argument of William H. Shockley on simplified spelling. A committee was appointed to have charge of the publication of the Raymond Memorial Volume. There were elected 70 members, 15 associates, and 1 junior associate. Three members were reinstated and the resignations of two were ac-cepted. The clues of 10 members who had been in active service with the allied armies were remitted. An extension of time for the payment of dues was granted to the 11 members.

Jan 12, 1919

By Dan Chun

Abstract-To facilitate the efficient handling of large volumes of information generated by logging exploration drill cores, a computer data bank system (GEOBANK) has been developed to store and retrieve the normally difficult to handle geologic information as well as the physical testing data. The data bank systematized the logging of drill core by first developing a standard list of adjectives or descriptors (with the corresponding assigned numerical codes) for the various stratigraphic categories that are also assigned numerical codes. The system uses the "floating-slot" concept and handles the data bank with one single input form.

Jan 9, 1978

By F. W. Glaser, W. Ivanick

A pressure-sintering method was used to produce binder-free and very dense TiC specimens. Some physical properties of these TIC bodies were determined and found to compare favorably with those of certain cemented Tic grades. It was also observed that the hot transverse rupture strength of TiC bodies remained substantially the same regardless of the amount or type of binder material used. STUDIES of the structure and physical properties of refractory materials have been intensified recently because of the urgent need for nonstrategic materials that retain their strength at high temperatures. Research aimed at determining and improving the physical properties of cemented carbides and borides has been accelerated with a view toward possible use of such materials in connection with turbine blades, rocket nozzles, and other high temperature applications. On the hypothesis that the strength requirements in connection with some of the above applications could be met only by proper choice of cementing agents for such refractory materials, the literature describing the physical properties of borides or carbides was reviewed. However, with a few exceptions,&apos;-" references were found only to compositions containing at least one or more auxiliary binder metals. Cobalt and nickel are among the most frequently employed cementing agents. The melting point of Tic (approximately 3250°C) and therefore the sintering temperature, at which notable densification of a cold pressed Tic powder compact could be expected in the absence of a liquid binder phase, is relatively high. The present study makes use of a high temperature, pressure-sintering procedure, recently described by one of the authors in connection with the sintering of binder-free ZrB,," to produce dense bodies of sintered Tic—free of any cementing agent. During the course of this sintering study, some physical properties of dense Tic bodies produced by this method will be discussed. Materials, Preparation of Samples, Testing Methods The procedure for the forming of Tic powder consisted of mixing graphite and TiH, powders in stoi-chiometric proportions, and heating this mixture in a H, atmosphere and carbon crucible by high frequency, to temperatures ranging between 1900° and 2100°C (3452" and 3812°F). The powdered carbide was then comminuted and screened to the desired particle size. Table I shows the chemical analysis of the two grades that were employed for the production of samples during this work. Bodies of Tic, approximately 2.5xlx0.5 cm were produced in graphite molds that were heated by direct conduction. Sintering was carried out at temperatures for time intervals ranging from approximately 0 to 30 sec under a constant pressure of about 1.3 tons per sq in. An alternate method for the production of samples consisted in cold pressing the individual Tic grades at pressures ranging from 4 to 10 tons per sq in. and sintering in a hydrogen atmosphere in graphite crucibles heated by high frequency induction. Sintering temperatures ranged from 2600° to 2900°C (4715° to 5255°F). Electrical testing was done by measuring potentiometrically the voltage drop over a length of 1.5 cm for a current of 10 amp at room temperature. Cross-sectional areas as well as densi-

Jan 1, 1953

United Engineering Society WALTER H ALDRIDGE J VIPOND DAVIES I V N DORR Engineering Societies Library Board SYDNEY H BALL ALEXANDER C HUMPHREYS GEORGE C SLONE JOHN H JANEWVAY Engineering Foundation Board H M BOYLSTON J VIPOND DAVIES GALEN H CLEVENGER Society for Promotion of Engineering Education WILLIAM KELLY ALLEN B ROGERS American Engineering Standards Committee GRAHAM BRIGHT GEORGE C STONE GEORGE E THACKRAY Alternates-RICHARD L LLOYD and HARLOWE HARDINGE

Jan 1, 1923

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.&apos; Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By R. Hogg

Sintering is a process in which the pore structure of an agglomerated powder is modified. For many applications, it is desirable to be able to control the pore structure in order to optimize such properties as mechanical strength and reactivity (availability and accessibility of solid surfaces to reactant gases, for example). In general, these properties will be determined by the total porosity and the pore size distribution of the agglomerate. In the work described in this paper, a physically realistic mathematical model for the sintering process has been developed. The model is based on the usual assumption that the pore system in an agglomerate can be treated as a network of interconnecting, cylindrical pores of continuously varying size. It is further assumed that the total pore length is conserved during the course of the sintering process. Using standard expressions for the rate of shrinkage of an individual pore, the model can be used to predict the changes in total porosity and pore size distribution as sintering proceeds. Experimental pore size distributions, obtained by mercury intrusion porosimetry, for the sintering of oxides appear to be in general agreement with the predictions of the model.

Jan 1, 1977