Search Documents

By Allen H. Rogers

THE need for coordinated effort on public problem by engineers has long been felt. Early in June there will assemble in Washington a conference composed of delegates from all the engineering organizations in the country. The call for this conference is issued by the Joint Conference , Committee of the four national societies as the completion of its work on the organization of a congress composed of delegates representing all the engineering organizations of the United States. The plan for this confederation was presented at a joint meeting of the administrative boards of the national founder societies on Jan. 23, 1920; and was unanimously approved in principle by that meeting. The work of the committee since that date has consisted in drafting a constitution of the organization to be presented at the conference for discussion and, after such amendments as may be adopted, acceptance.

Jan 1, 1920

By Marius R. Campbell

Does mine-sampling show the commercial value of a coal, and if so, how should it be done? This question is often asked, but seldom answered. During the past summer, while engaged in securing coal for the Government coal-testing plant at St. Louis, I had an excellent opportunity to obtain information on this subject, and the results seem to furnish an answer to the questions propounded above. Sampling for the Geological Survey Coal-Testing Plant. In organizing the work of the testing-plant, it was decided that coal in car-load lots only would be accepted for testing, also that this coal should be loaded under the immediate supervision of a representative of the plant, so as to be certain that the car-load sample would be representative. As an additional check on the work, two mine-samples were to be collected from each mine visited, and these samples, as well as the sam¬ple from the car when it was received at the testing-plant, were to be carefully analyzed at the chemical laboratory, which was established in connection with the plant and operated under the direction of Prof. N. W. Lord, of the Ohio State University, Columbus, Ohio. Mine-Sanmhling:-Mine-samples were collected with great care by me and my assistants, Messrs. J. Shober Burrows, John W. Groves and Frank W. De Wolf. The dominant idea in the regulations which were adopted for mine-sampling was that it should be done in such a manner that the sample would have the same composition as the commercial output of the mine. .

Sep 1, 1905

By D. W. Fuerstenau

Measurement of zeta potentials is a useful tool to study the surface chemistry of minerals under flotation conditions. Because there is continued interest in this approach, the apparatus for obtaining zeta potentials of nonconducting solids by the streaming potential method is outlined here. Fig. 1 illustrates the streaming potential apparatus. The streaming potential cell or plug consists of two 24/40 standard ground joints (4) joined with a piece of pyrex tubing 60 mm long and 12 mm in diam (5). The electrodes are made of bright platinum disks 19 mm in diam and 1 mm thick through which 0.5-mm holes have been drilled (6). To the surface of each is welded a piece of 80-mesh platinum gauze. Each electrode is permanently mounted on the ends of the inner parts of the two standard joints by means of a platinum wire (7) which connects it to the tungsten seal at the end of the cell (8). For ease in cleaning and handling the apparatus, the streaming cell is fastened to the 500-ml reservoir flasks (1) by means of two 18/9 ball and socket joints (2). This particular arrangement permits passage of the solution in either direction through the plug of particles. Flow of solution can be stopped by a stopcock (3). One of the reservoir flasks has a large opening to permit insertion of either a thermometer or a pair of electrodes for measuring pH of solutions within the system. In making the experiments, the plug is filled with 48 to 65-mesh particles, but a layer of 28 to 35-mesh particles is placed at each electrode to prevent any of the finer particles from passing through holes in the electrodes.

Aug 1, 1956

By W. Weissberger, Frankiewicz, L. Pommier

Introduction In the U.S., about one-quarter of the fuel oil and natural gas consumption is associated with power production in utility and industrial boilers and process heat needs in industrial furnaces. Coal has been an attractive candidate for replacing these premium fuels because of its low cost, but there are penalties associated with the solid fuel form. In many cases pulverized coal in unacceptable as a premium fuel replacement because of the extensive cost of retrofitting an existing boiler designed to burn oil or gas. In the cases of synthetic fuels from coal, research and development still have a long way to go and costs are very high. Another option, which appears very attractive, is the use of solid coal in a liquid fuel form - coal slurry fuels. Occidental Research Corp. has been developing coal slurry fuels in conjunction with Island Creek Coal (ICC), a wholly-owned subsidiary. Both coal-oil mixtures and coalwater mixtures are under development. ICC is a large eastern coal producer, engaged in the production and marketing of bituminous coal, both utility steam and high quality metallurgical coals. There are a number of incentives for potential users of coal slurry fuels and in particular for coal-water mixtures (CWMs). First, CWM represents an assured supply of fuel at a price predictable into future years. Second, CWM is available in the near term; there are no substantial advances in technology needed to provide coal slurry fuels commercially. Third, there is minimal new equipment required to accommodate CWM in the end-user's facility. Fourth, CWM is nearly as convenient to handle, store, and combust as is fuel oil. Several variants of CWM technology could be developed for different end-users in the future. One concept is to formulate slurry at the mine mouth in association with an integrated beneficiation process. This slurry fuel may be delivered to the end-user by any number of known conveyances such as barge, tank truck, and rail. Slurry fuel would then be stored on-site and used on demand in utility boilers, industrial boilers, and potentially for process heat needs or residential and commercial heating. An alternative approach is to formulate a low viscosity pre-slurry at the mine mouth and to pipeline it for a considerable distance, finishing up slurry formulation near the end-user's plant. Finally, at the other extreme of manufacturing alternatives, washed coal would be shipped to a CWM manufacturing plant just outside the end-user's gate. Depending on fuel specifications and locations of the mine and end-user facility, any of these alternatives may make economic sense. They are all achievable in the near term using existing technology or variants thereof. The Coal-Water Mixture CWMs contain a nominal 70 wt. % coal ground somewhat finer than the standard pulverized ("utility grind") coal grind suspended in water; a complex chemical additive system gives the desired CWM properties, making the suspension pumpable and preventing sedimentation and hardening over time. Figure 1 shows the difference between a sample of pulverized coal containing 30 wt. % moisture and a CWM of identical coal/water ratio. The coal sample behaves like sticky coal, while the CWM flows readily. The combustion energy of a CWM is 96-97% of that associated with the coal present, due to the penalty for vaporizing water in the CWM. Potentially any coal can be incorporated in the CWM, depending on the combustion performance required and the allowable cost. CWMs are usually formulated using high quality steam coals containing around 6% ash, 34% volatile matter, 0.8% sulfur, 1500°C (2730°F) initial deformation temperatures, and energy content of 25 GJ/t (21.5 million Btu per st). Additional beneficiation to the 3% ash level can be accomplished in an integrated process. There are a number of minimum requirements which a satisfactory CWM must meet: pumpability, stability, combustibility, and affordability. In addition, a CWM should be: resistant to extended shear, generally applicable to a wide variety of coals, forgiving/flexible, and compatible with the least expensive processing. It was found that a complex chemical additive package and control of particle size distribution are necessary to achieve these attributes simultaneously, while maximizing coal content in the slurry fuel. Formulation of Coal-Water Mixtures A major consideration in the manufacture, transportation, and utilization of a slurry fuel is its pumpability, or effective viscosity. Most CWM formulations are nonNewtonian, i.e., viscosity depends on the rate and/or duration of shear applied. Viscosities reported in this paper were obtained using a Brookfield viscometer fitted with a T-spindel and rotated at 30 rev/min, thus they are apparent viscosities measured at a shear rate of approximately 10 sec-1. The instrument does reproducibly generate a shear field if spindle size and rotation rate are held fixed. By observing the apparent viscosities of several slurries at fixed conditions it is possible to obtain a relative measure of their viscosities for comparison purposes. A true shear stress-shear rate relationship at the shear rates at which the CWM will be subjected in industry may be obtained using the Haake type and a capillary viscometer. These viscometers are used for specific applications. However, for comparison purposes, apparent viscosities are reported.

Jan 1, 1985

By Rztssell H. Bennett

A SURVEY of the Mesabi Range iron-ore industry demonstrates that a satisfactory degree of technical progress has been achieved in the last fifteen years. This advance has not been made over a uniform front, but, by salients and bays, according to the different initial positions, economic and technical, of the component producing companies. The producers endowed with rich ore have in general, because of natural advantages, progressed more slowly than their neighbors with leaner properties. The advance has been made step by step all along the line -blasting, loading, hauling and concentrating-and without the benefit of radical innovation. There have been, for instance, no such parallel discoveries in iron ore as leaching and flotation in copper. The much lower unit price of iron operates, of course, to bar the application of these and other practices developed for the higher-priced metals. There exists, however, a radically new concentration process whose technology is well worked out and which may become economically operative in the not too distant future; this, as so often happens in engineering advance, because of recent developments in an entirely unrelated field. First, however, let me devote a paragraph or two to the more important economies effected in mining.

Jan 1, 1932

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By William R. Webster

The unusual interest taken in the papers on steel at the New York (1922) meeting showed that the time is ripe for the renewal of the general discussion of the physics of steel, on the same lines that wete used formerly and produced such good and lasting results. The curves shown in Figs. 1 to 4 and the appendix were added to my paper1 after the February meeting, but, unfortunately, Figs. 1 and 3 were transposed; the curves on page 252 are for bessemer steel and belong on page 254; while those on page 254 are for open-hearth steel and belong on page 252. These errors are evident at once on referring to the data in Tables 1 and 2, pages 227 and 228. The curves for each 0.05 per cent. of carbon and manganese in basic open-hearth steel are given in Figs. 1 and 2; these lines for the lower carbons and manganese are comparatively uniform. Figs. 3 and 4 give similar lines for carbon and manganese in bessemer steel. The large break in the carbon lines from 0.55 per cent. to 0.60 per cent. is caused by much higher silicon in the steels of 0.60 per cent, carbon and over that are used for springs, etc. The estimated ultimate strength of pure iron, and the increase in strength by carbon, phosphorus, and manganese, with the different views regarding the same, were given and diseussed. All of this can be considered as an introduction to the practical use that is now being made of such data in selecting the heats of steel best suited to give the required physical tests called for in the finished rolled material. The chemical composition of the steel, of course, tells only a part of the story, as many other factors that have an influence on the physical properties of the steel must be considered, and controlled as far as is possible. Some of these have already been referred to, but there are other important ones to be considered and discussed.

Jan 1, 1923

By Earl C. Henry

Magnetic iron ore was mined in Essex County, N. Y., during the American Revolution; Benedict Arnold is said to have mined ore near Port Henry to secure iron for chains and spikes for the Lake Champlain fleet. Details regarding the operations prior to 1804 are not easily obtained but work on a commercial scale appears to have been started about 1838. The Witherbee, Sherman & Co. was established in 1849. The property of the district is held in fee almost entirely by the mining companies. The Mineville iron-ore district, as well as the entire Adirondack region, belongs to the pre-Cambrian complex. The readily identified rocks consist of gabbro, anorthosite, syenite, and granite, and are classed as igneous, eruptive, and intrusive. In addition, there is a great variety of gneisses, rocks with a variable mineral composition but all more or less distinctly foliated. The Grenville series are the oldest rocks in the district; this series consists of graphitic white limestones, graphitic sandstones, and quartzites and gneisses with or without graphite. The orebodies occur in the gneissic rocks and are comformable to the structure of the rocks. The typical occurrence of the ore in this district is in lenticular bodies with a parallel pitch to the southwest; this structure is best exemplified in the New Bed mine. The Harmony and Old Bed orebodies are faulted by two sets of diabase dikes, one set having a southwest strike and the other set an east-west strike. The ores occurring in the acid gneissic rocks are non-titaniferous. The ores occurring in the gabbros and anorthosites are high in titanium; these deposits are irregular, have no structural relation with one another, and are unquestionably of igneous origin. The origin of the gneissic rocks and the ores therein contained is not settled; both the sedimentary theory of ore concentration and the igneous theory of magmatic segregation have been advanced. The iron mineral in all the orebodies is crystalline magnetite; some very perfect and large specimens have been obtained. The gangue is

Jan 1, 1925

By Cyril Wells

THE diffusion of carbon in gamma iron plays an essential role in many metallurgical processes. In carburizing, in graphitizing, in homogenizing, in the formation of pearlite from austenite, and in other processes, migra-tion of carbon in gamma iron occurs.1,2 A full understanding of the rate at which these processes occur obviously requires a knowledge of the rate of diffusion of carbon. In carburizing, for example, the depth of carbon pentration is determined by the carbon concentration in solid solution at the surface, and by the rate of diffusion inward of the carbon. Until reliable data on the rates of diffusion of carbon are available it is unlikely that a full quantitative description of this process will be obtained. In the formation of pearlite from austenite, the segregation of carbon and alpha iron from the austenite obviously requires the diffusion of carbon; the rate at which pearlite nodules grow is evidently controlled at least in part by the rate of diffusion of carbon; it is unlikely that we shall understand the factors that determine the rate of growth unless data on rates of diffusion of carbon, and the variation of these with com-position, grain size, and temperature are available. Accordingly it was decided: (1) to determine, more accurately than hitherto, the diffusion coefficients of carbon in austenite over a wide temperature and a wide concentration range, (2) to study the influence of grain size and impurities on this diffusion coefficient, and (3) to study the effect of manganese and nickel on the rate of diffusion of carbon in the austenite of manganese and nickel steels, respectively; the influence of carbon on the rate of diffusion of manganese and of nickel will be made the subject of later papers. The rate of diffusion of carbon in gamma iron has been studied by Runge3 by Tammann and Schönert4, by Bramley and co-authors,5-14 and

Jan 1, 1940

By W. E. Rice

The ceramic industry has to do with forming or molding articles of clay, and imparting to them their characteristic properties of permanence, strength and color by subjecting them to heat treatment in kilns. This heat treatment is commonly known as "firing" or "burning." The art of firing clay ware antedates the industrial use of coal; hence wood was the fuel first used, and the earliest kilns were built to burn wood. The majority of the clay ware produced today is fired in periodic kilns that are essentially enlarged structures similar to the earliest enclosed kilns; a kiln consists of a large chamber 16 to 32 ft. dia. (or rectangular) in which the ware is charged and fired either in direct contact with flame or hot gases from the fuel, or in saggers which shield the ware from direct contact with the gases. The fuel is burned in a number of small furnaces built in the thick wall that encloses the chamber; these furnaces are from 16 to 36 in. wide and from 3 to 5 ft. long; some of them have horizontal or sloping grates, but many have no grates; the last are called "dead-bottom" furnaces. The temperature necessary to mature the charge in the kiln varies for different clays; for some it is as low as 1800°, and for others as high as 2700" F. Wood was an ideal fuel for the low temperatures that were used in early kilns; it burns freely and produces a long, clean flame, which promotes uniform distribution of the heat in the kiln; it does not coke and so restrict the passage of air through the fuel bed; the ash does not melt in the fuel bed to form clinker; and the ash that is carried into the chamber and deposited on the charge does not contain iron and sulfur to discolor the clay. The extent of the ceramic industry now precludes the general use of wood in kilns, so that today this industry is one of the large users of bituminous coal, burning more than eight million tons annually in kilns. Manufacturing plants usually are at or near the source of clay, with deposits of coal suitable for kilns occurring near the clay. The cost of coal is the largest single item of expense in the manufacture of clay ware, and, because all coals are not equally suitable for the process, the careful selection of coal is important. In this selection the desidera-

Jan 1, 1932

By Albert Hill Fay

IN giving a sketch of the geology and mining of the tin-deposits of Cape Prince of Wales, a short description of the geographic and climatic conditions may be of special interest on account of this being a part of the world of which very little is known, even by the reading public. As shown in Fig. 1, the location of the Cape is lat. N. 65° 35' and long. W. 168°. It is bounded on the north by the Arctic ocean ; on the west by Bering strait and on the south by Bering sea. It is the western-most point of the mainland of North America, and to the west, across the strait, one can see East Cape, Siberia, which consists of a rugged, steep coast of granite cliffs. The climatic conditions are of interest because of the part they have had in the surface geology, and also because they affect mining from an economic standpoint. In connection with the climate and geography, it does not seem out of place here to quote a few lines from the prologue of The Wandering Jew, written by Eugene Sue, under the caption '1 The Land's End of Two Worlds."

Sep 1, 1907

By James Lorimer

THE topography at the Stan Trg mine facilitated early exploration by adits; in consequence adit levels were developed at horizons 865, 795, and 760 meters above sea level, and the levels in the mine 'are named according to their elevation. Exploitation started from the 760-m. level . upwards while simultaneously first steps were taken with regard to mining in depth. A deep dewatering adit 2.5 km. long now gives access to the deposit at the 610-m. horizon which also is connected with the 760-m. adit level by a three-compartment main hoisting shaft. Main levels have been developed internally from

Jan 1, 1936

By Thomas T., Read

ALTHOUGH the first colonists in the area that is now the A United States, whether Spanish, French or English in nationality, were usually keenly interested in the possibilities of mineral wealth, it is a curious and interesting fact that none of them happened upon the mineral deposits that eventually were to make this the greatest mineral-producing country; up to 1800 it would probably have been rated as rather poor in minerals. Spanish explorers traversed the southeastern United States with- , out finding the Appalachian gold deposits that aroused so much interest in the early nineteenth century; Coronado sought in vain for the seven golden cities of Cibola; and the important gold \ deposits of California were not discovered until the political sovereignty of the region had passed from Mexico, which had held it for three centuries. The French also held Canada for nearly two centuries (and the British for another century) without finding the mineral deposits in Ontario and Quebec that now are so important. Though they knew of the copper of the Keweenaw peninsula, the lead ores. of Wisconsin and Missouri, and the coal of Illinois in the seventeenth century, these deposits were all too remote for exploitation. In the area held by Great Britain, iron smelting was planned at Jamestown as early as 1619 and was actually begun at Lynn, Mass., in 1643. The industry grew slowly, at first, but had reached considerable importance before the Revolution. Commercial bituminous coal mining began about 1750 in Virginia but anthracite mining in Pennsylvania was not started until 1800. As a result there was naturally little interest in the technical aspects of mineral prodnction here before 1800 by any except the few people who were actually engaged in it. Students of natural science were much interested in minerals, however. The activities of those who rank as geologists are so thoroughly covered in

Jan 1, 1941

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

By J. R. Bell, W. J. Childs, J. H. Bucher, G. A. Wilber

A technique for determining recrystallization times as short as 0.10 sec was developed utilizing the "Gleeble", a commercially available testing system designed for the study of short-time, high-temperaLure themal and mechanical processes. The procedure consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading- to failure. The magnitude of the ultimate load obtained upon reloading decreased with delay lime as recrys-lallization proceeded. The technique was applied to austenite recrystallization in AISI 1010 and AISI 1010 uith 0.02 pct Cb steels. For each steel the reduction in area given the specimen on the first pull was mainlairred at 30 ± 5 pct and recrystallization times deterntined at various temperatures. The results indicaled a significantly slower rate of recrystallization for the columbium-modified composition, suggested the presence of- a recovery stage in the softening process , and indicated a greatly increased softening rate at a temperatuve where significant allotropic transformation to a partially ferritic Structure could occur. In recent years increasing attention has been paid to the fact that the process of recrystallization of austenite deformed at elevated temperatures is far from instantaneous at many practical hot-working temperatures.1-3 This realization has given rise to such terms as hot cold-working1 or warm-working,2 These terms generally describe processes where the recrystallization rate at the temperature of deformation is slow enough to have an appreciable effect on mechanical properties despite a relatively high deformation ternperature. The mechanical properties of interest can be either the properties at the deformation temperature as in hot-workability studies4 or the room-temperature properties after cooling as in the many recent studies of various thermomechanical processes172 where heat treatment and deformation are intentionally combined to give a unique set of room-temperature properties. Because of this interest in processes where the austenite recrystallization kinetics can be an important variable, the development of quantitative methods of following the course of short-time, high-temperature recrystallization has received increasing attention.l,3,5 The experimental methods to date have, in general, relied upon rapidly deforming the austenite, holding at temperature for various brief intervals, quenching as G.A.WILBER and W. J. CHILDS, Members AIME,are Research-Fellow and Professor, respectively, Rensselaer Polytechnic Institute, Troy, N. Y. J. R. BELL and J. H. BUCHER, Member AIME, are Research Engineer and Research Supervisor, respectively, Graham Research Laboratory, Jones & Laughlin Steel Co., Pittsburgh, Pa. Manuscript submitted March 13, 1968. IMD. rapidly as possible, and then using room-temperature measurements to follow the recrystallization process. Although such methods can be successfully applied to certain alloy steels, the existence of the allotropic transformation during cooling of plain-carbon or low-alloy steels tends to obscure the results. Thus, such room-temperature measurements as hardness and X-ray line widths do not correlate well with the extent of austenite recrystallization before quenching,5 and results based on room-temperature microstruc-tural observations are dependent upon the success in correlating the observed structure with the prior aus-tenitic grain structure.1,3,5 The purpose of the present work was to develop a quantitative method for the determination of short-time, high-temperature recrystallization rates, based on measurements made at the temperature of deformation. EXPERIMENTAL TECHNIQUE The basic technique consisted of heating a small tensile specimen to a given temperature of hot deformation, loading to a given reduction in area, unloading, delaying various intervals at temperature, and then reloading to failure. The data were obtained in the form of traces of load and elongation as a function of time. Due to the high deformation temperature, the strain hardening introduced during initial loading was progressively annealed out with holding time after unloading and the loads obtained upon reloading decreased as this softening proceeded. Although the value of the second load at any Consistent point On the load-elongation curve could have been used as a measure of the degree of softening, the most convenient to use was the ultimate load. The softening indicated by the decrease in the second ultimate load with time is essentially a process of annealing of cold-worked material at a high deformation temperature. Although some recovery grain growth may contribute to such a softening process, it is generally considered that the major softening which must take place to achieve complete removal of substantial Strain hardening will occur by the formation of new, stress-free grains. As the results of this work indicate that essentially complete removal of strain hardening did in fact occur. the primary softening process will be attributed to recrystallization, and specific reference made where it appears that other mechanisms may be contributing to the total observed softening. It would, of course, be of interest to attempt to correlate the results of this work with the actual austenite fraction recrystallized as determined by other techniques. This was not attempted in the present work because it would have required running a large number of additional specimens and, as discussed previously, there is limited assurance that the results would accurately reflect the prior austenite fraction recrys-

Jan 1, 1969

By D. H. Woodard

One of the principal uses of polarized light in metallurgy is to show the granular structure of metals by contrasting reflections. This use is confined largely to anisotropic metals, such as beryllium, tin, magnesium, and the like.1 Recently, Hone and Pearson2 have extended the use of polarized light to include the isotropic metal aluminum. This was made possible by the formation of an anodic film that was optically anisotropic and that had a fixed and reproducible structural relationship to the grains in the substrata. With their method, it was possible to indicate localized textures in annealed aluminum sheet. In the course of an investigation of plastic deformation at the National Bureau of Standards, it was found that the isotropic single phase alloy Monel could be made optically anisotropic by treatment with the usual Monel contrast etchant. Experiments soon showed that dif- , ferences in orientation could be detected easily. Previous investigations involving the use of polarized light have been restricted to annealed metals. In this paper it will be shown that inhomo-geneous plastic deformation which results in lattice bending and development of deformation bands, experienced by individual grains in polycrystalline Monel, is revealed in the microstruc-ture. This interpretation of the micro-structure was confirmed by a study of slip lines formed after prior plastic strain. Materials and Procedure The material used was Monel, the chemical composition of which was C—0.17 pet, Mn—1.28 pet, Fe—1.61 pet, S—0.009 pet, Si—0.17 pet, Cu— 30.70 pet, Ni—66.04 pet. The material was divided into 2 lots which were treated as follows: Lot A was heated at 1700°F for 3 hr to produce a fully annealed, coarse grained structure. Lot B was heated at 1400°F for 1 hr to produce a close approximation of a fully annealed structure without appreciable increase in the grain size of the original material. After each of these heat treatments the material was cooled in air. Samples for metallographic examination were cut from tensile and compression test specimens and were prepared by grinding on lead-tin laps, followed by electrolytic polishing, † Etching and the development of ridges were avoided by keeping the voltage above 3.8 and by preventing contamination of the polishing solution with water. Monel, when polished and treated with most etchants, is optically isotropic. However, when given a light etch for about 4 sec with the Monel contrast solution the surface of the metal becomes optically active. The microstructure when observed under crossed nicols* appears different from that viewed by ordinary light. This is shown by a comparison of micrographs made of the same area of a plastically deformed specimen using polarized light (Fig la) and white light (Fig 16). If Monel, which has been lightly treated with the contrast etchant, is slightly deformed by compression, rectangular figures are apparent over the specimen. However, within too short a period to be photographed, these rectangles become circular, probably because of surface tension effects within the etched film. The two observations,

Jan 1, 1950

By F. F. Lines

IT is not the intention of the writer to enter into a discussion of the relative merits of the duplex process as compared with the straight scrap and pig iron process, working under the same conditions, but rather to present in a general way several modifications of the former process, and then describe the method adopted by the Maryland Steel Co., as best suited to local conditions, and also to meet the metallurgical problem presented in the removal from the iron of an unusual constituent-chromium. The principal factors to be considered in deciding whether or not duplexing should be employed are: (1) Chemical constituents of pig iron. (2) Variety and quantity of steel to be produced. (3) Relative cost of pig iron and scrap. (4) Regularity of operation. (5) Capital to be invested. (6) An existing Bessemer plant. Having decided to adopt the duplex process, several combinations may be used, viz.: (1) Acid-lined converter with basic open hearth. (2) Acid-lined converter with electric furnace. (3) Basic-lined converter with basic open hearth. (4) Basic-lined converter with electric furnace. (5) Basic open hearth with electric furnace. The combination of an acid-lined converter with a basic open-hearth furnace is the one most commonly employed, and as it is the one best adapted to the conditions encountered at the plant of the Maryland Steel Co., we will briefly outline the advantages and disadvantages of the different methods of working.

Jan 4, 1915

By G. L. Spencer

There is no question as to the importance of the part played by the retort in modern zinc smelting. A satisfactory retort should have properties that will result in resistance to slagging action and fire cracks, and have no tendency, or at least only a small tendency, to soften and bend under furnace heat. The life and cost of a retort also are extremely important factors. The trend in zinc smelting during the past few years has been toward longer retorts and .higher charge density. This is caused by the fact that the diameter is limited to 9 or 10 in. because of heat penetration difficulties in larger sizes. Consequently, increasing the length of the retort and density of charge offers the only practical means of increasing the amount of zinc produced per retort. The stiff-ness of a retort perhaps is the most important factor, as slag accumulates in the bottom of a retort which has sagged and very quickly cuts through, often ruining the retorts below. The development of the high-silica retort is a result of the demands made by the trend toward heavy charges. Materials Used for High-silica Retorts The materials used in the manufacture of high-silica retorts at East St. Louis are fireclay, grog and silica flour. Analyses are given in Table 1. The fireclay comes from the St. Louis district. The grog consists of clean firebrick culls, and the silica flour, a very high-grade material, is purchased in the form of a flour that has been ground through 140 mesh.

Jan 1, 1931

By Shiou-Chuan Sun

THE presence of an excessive amount of tough froth in the flotation of minerals, particularly coals, may create trouble in dewatering, filtering, and handling. Froth is also a nuisance in many chemical industries.' This paper presents a study on the destruction of extremely tough froths with intense high-frequency sound. The data indicate that sound waves can be employed for continuous atandsoundwavescan instantaneous defrothing. A powerful high-frequency siren was used in obtaining the data. Also tested was an ultrasonorator of the crystal type with a frequency range of 400, 700, 1000, and 1500 kc per sec and a maximum power output from its amplifier of 198 w. The results, not presented, indicate that as now designed this machine is not suitable for defrothing. Although the sound generators of the magnetostriction type2,3 and of the electromagnetic type'.' were not available, it is beelectromagneticlieved they are capable of producing the required sound intensity for defrothing. The use of ultrasonics for defrothing was suggested by Ross and McBain1 in 1944. Ramsey8 reported in 1948 that E. H. Rose mentioned a supersonic device that broke down flotation froth but with low capacity. The writer has not been able to find any published literature containing practical experiments. Theoretical Considerations The mechanism of defrothing by sound is attributed to the periodically collapsing force of the propagated sound waves and the induced resonant vibration of the bubbles. The collapse of froth is further facilitated by the sonic wind and the heat of the siren. Sound waves can exert a radiation pressure'," against any obstacle upon which they impinge. When a froth surface is subjected to the periodic puncturing of sound waves, the bubbles are broken. According to Rayleigh9 and Bergmann,12 the radiation pressure of sound, P, in dynes per sq cm is given as: P = 1/2 (r+1)i/v where r is the ratio of the specific heats of the medium through which sound is traveling and is equal to 1 on the basis of Boyle's law; i is the sound intensity in ergs per sec per sq cm, and v is the sound velocity in cm per sec. In this case, the accuracy of the formula is only approximate, because a perfect reflection can hardly result from a column of froth. In addition to the radiation pressure, the propagated sound waves cause the bubbles of the froth to have a resonant vibration.'" he vibratory motion of the bubbles causes collision and coalescence, thereby weakening if not breaking the bubble walls. Sonic wind and heat were also generated." The sonic wind can exert pressure on the froth surface, and the heat can evaporate the moisture content of the bubble walls as well as expand the enclosed air. Apparatus The defrothing apparatus, shown in Figs. 1 and 2, consists of a powerful high-frequency siren, a glass or stainless steel beaker of 2-liter capacity with 12.4 cm diam and 17.1 cm height, and a metal reflector. The beaker was placed 2 in. above the top point of the siren. The metal reflector was adjusted to reflect and focus the generated sound waves into the central part of the beaker. Fig. 2 shows the crystal probe microphone used to measure the acoustic intensity and the mandler bacteriological filter employed to introduce compressed air into the beaker for frothing. The apparatus was enclosed in a soundproof cabinet equipped with a glass window. The siren, shown in Fig. 3, consists of a rotor that interrupts the flow of air through the orifices in a stator. The rotor, a 6-in. diam disk with 100 equally spaced slots, is driven by a 2/3 hp, Dumore W2 motor at 133 rps. The frequency of the siren can be varied from 3 to 34 kc. The maximum chamber pressure is about 2 atm, yielding acoustic outputs of approximately 2 kw at an efficiency of about 20 pct. The siren itself is relatively small and can be operated in any orientation. A detailed description of the siren has been given by Allen and Rudnick.11 Collapse of Froth To study the sequence of the collapse of froth, the glass beaker was partially filled with 920 cc water, 100 g of —150 mesh bituminous coal, 0.3 cc petroleum light oil, 0.2 cc pine oil and 1.54 cc Pyrene foam compound. This mineral pulp was agitated for 5 min and then aerated through a mandler filter until the empty space of the beaker, approximately 9 cm high, was filled completely with min-

Jan 1, 1952

By Amitava Gangulee, Michael B. Bever

The effects of changes in short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions have been investigated. The heats of formation at 273°K of several alloys after two different thermal treatments were measured by liquid metal solution calorimetry. Their electrical resistivities were measured at temperatures ranging from 4° to 773°k. Tensile tests and microhard-ness measurements were carried out at room temperature. An effective short-range order parameter and an effective interaction energy are defined. The measured changes in the properties are interpreted in terms of these quantities. The short-range order parameter is evaluated separately from calorimetric and X-ray data; the results are in fair agreement. Increasing short-range order lowers the resistivity of- the silver-rich Ag-Mg alloys but does not measurably affect the temperature dependence of the resistivity. Short-range order increases the yield stress of these alloys but does not affect the ultimate tensile stress. Changes in the effective short-range order parameter independently obtained from measured changes in the heat of formation, resistivity, and yield stress are in fair agreement. THE thermodynamic, electrical, and mechanical properties of solid solutions have been investigated as functions of composition in many alloy systems, but the effects of configurational variables, such as short-range or long-range order, on these properties have received much less attention. The silver-rich terminal solid solutions in the system Ag-Mg are well-suited for the investigation of the effects of order. The composition of these solid solutions may be varied over a range extending to about 27 at. pct Mg.1 Appreciable short-range ordering is likely to take place in these solid solutions; the degree of short-range order can be varied by suitable thermal treatments. In the alloy Ag3Mg long-range ordering is possible.2 This paper is primarily concerned with the effects of short-range order on some thermodynamic, electrical, and mechanical properties of the silver-rich Ag-Mg solid solutions.-The long-range ordering transition is the subject of a concurrent paper.3 1) EXPERIMENTAL PROCEDURES 1.1) Preparation of Specimens. Ag-Mg alloys containing up to 26.4 at. pct Mg were prepared by melting 99.99 pct pure Ag (obtained from Baker Chemical Co.) and 99.99 pct pure Mg (obtained from Eastman Chemi- cal Co. or Johnson Mathey & Co.) in graphite crucibles under molten potassium chloride. The solidified ingots were homogenized at 823°K for 10 days in evacuated Vycor capsules. A surface layer 6 in. thick was then removed by machining. The ingots were swaged into rods (2.5 mm diam) which were drawn into wires (1.0 mm diam). The wire specimens were annealed at 773°K for 24 hr in vacuum and either quenched into iced brine or cooled to room temperature over a period of 15 days. The average grain diameter (obtained from the linear intercepts) was about 0.1 mm. 1.2) Calorimetry. The heats of formation of the alloys were measured in a tin solution calorimeter as the difference in the heat effects of alternate additions of samples of an alloy and the mechanical mixture of its component elements. The additions were made from 273°K to the bath at about 623°K. The heat effect on addition of the alloys was approximately 5.5 kcal per g-atom. The procedure and the method of calculation have been described.4 1.3) X-Ray Diffraction. Short-range order parameters of two alloys were calculated from diffuse scattering intensities,' obtained with briquettes made from powdered specimens. A GE-XRD 5 diffractometer with filtered copper radiation was used. The absolute intensities were based on calibrations with paraffin. 1.4) Resistivity Measurements. The electrical resistivities were measured by a potentiometric method in which the potential drop across the specimen was compared with that across a standard resistance. For measurements below room temperature, the specimens were immersed in liquid helium (4°K), liquid nitrogen (78°K), dry ice and trichloroethylene (195°K), or ice and water (273°K). Measurements above room temperature were made on specimens held in a furnace under helium or in vacuum. The resistivity measurements were reproducible to ±0.5 pct or less. 1.5) Mechanical Tests. Tensile tests were carried out at room temperature with a Tinius-Olsen XY elec-tromatic Universal testing machine. Wire specimens (nominal gage length 1 in.) were used. The strain was measured with an extensometer, which had a sensitivity of 4 x 10-5; the strain rate was 10-3 min-1. Microhard-ness measurements were made with a square-pyramid indenter and a 100-g load.11 2) RESULTS AND DISCUSSION All measurements were made on two parallel sets of specimens, one quenched and the other slowly cooled from 773°K. The reported values are the averages of at least three measurements. In the range of magnesium concentration substantially below that of the composition Ag3Mg, quenched alloys have less short-range order than slowly cooled alloys. As the magnesium concentration approaches that of Ag3Mg, slow cooling develops long-range order. Quenching sup-

Jan 1, 1969