Search Documents

By Carle R. Hayward

GENERAL conditions in the lead industry have registered a distinct improvement. The first signs of a strengthening market were found in an increasing demand for scrap. There is keen competition for old battery plates both by large and small dealers. The large operator smelts them either alone or in combination with ores or other lead-bearing material, giving an antimonial lead for which there is brisk demand. The small operator usually has three alternatives. He may simply melt out the metallics in a kettle at low temperature, giving an antimonial lead and a pulverulent lead oxide; he may fuse under oxidizing conditions, giving a soft lead and lead-antimony slag; or he may fuse under reducing conditions, giving a relatively low-grade antimonial lead and a low-antimony slag. In each case the metal product is used or sold, and the dross or slag sold to a large smelter. It will be interesting to see what the final outcome will be of this situation which is generally conceded to be unsatisfactory.

Jan 1, 1937

By L. S. Castleman, R. K. Hotzler

We are currently studying the effects on recrys-tallization of impurities diffused into dispersion-hardened alloys. Our interest in this phenomenon was originally aroused by the observation that the recrystallization temperature range of tungsten "doped" with alumina and silica, or with thoria, is lowered drastically if nickel is plated onto the tungsten prior to heat treatment.' In this note, we report a similar effect that sulfur has on the recrystallization behavior of thoriated nickel. The experimental procedure for this exploratory phase of the investigation has consisted simply in heating commercially obtained stress-relieved samples of thoriated nickel for varying temperatures and times in sealed capsules containing air and small quantities of sulfur. The samples contain 2.4 vol pct thoria and initially less than 18 ppm S by weight; they are prepared either from 0.5-in.-ciiam rod stock or from 0.092-in. sheet and are in the "as-received" (stress-relieved) condition prior to exposure. In an atmosphere free of sulfur, such samples do not show evidence of recrystallization after being annealed for 1 hr at a temperature of 2500°F (1372C).2 The photomicrograph in Fig. 1 shows the microstructure of one of our samples annealed for 75 hr at 1000° C (1832°F) in a sulfur-free capsule. The grain structure is hardly evident (if at all) at 465 times magnification. In contrast, the photomicrograph of Fig. 2 shows the recrystallization that has taken place in a sample exposed to sulfur for 5 hr at 1000°C (1832°F). A nickel sulfide phase is visible at the grain boundaries of the light-appearing grains. We have also observed recrystallization to occur in a sample annealed at 600°C (1112°F) for 25 hr. This temperature is below the 637°C (1178°F) eutectic in the Ni-S system. In the latter case, no nickel sulfide phase is evident in the microstructure. Moreover, we have noticed the occur-

Jan 1, 1969

ARTHUR CROWFOOT, Morenci, Ariz. (communication to the Secretary*).-In order to set at rest any doubts in regard to the reasons for selecting the Callow pneumatic flotation process for use in the concentrators of the Arizona Copper Co., Ltd., at Clifton and Morenci, I am presenting the following facts gained from the results of test work carried out on the Callow and Cole-Bergman types of flotation machines at Morenci. Prior to the comparative test of merit between the Callow and Cole-Bergman machines, many months' time and a large amount of money had been expended in the development and testing of the Cole-Bergman machine, and it was necessary to decide quickly what make of machine was best to install. The Callow pneumatic flotation process was recommended for installation in our concentrators for the following reasons: The results indicated: 1. That the Callow system made the highest extraction of copper values from the feed treated. 2. That the Callow system was simpler to operate and could he operated it a lower cost. 3. That the Callow system operated with a lower air pressure. (The question of the actual power consumption of the two types of machines was not definitely settled at this time.) During the official test period the Callow flotation apparatus showed an additional recovery of from 1 to 1.5 lb. of copper per ton more than the Cole-Bergman machine, this difference being maintained by further treatment of the tailing from both machines. The simplicity of the operation of the Callow flotation system is one of its notable features, two operators per shift being able to handle 90 standard cells and blower equipment.

Jan 7, 1917

By A. B. Kinzel, Walter Crafts

Inclusions of nonmetallic matter have long been recognized as objectionable in steel. A complete theory of the effect of inclusions, which is consistent with that held today, was outlined in Howe's early work on the metallurgy of iron and steel. This, by analogy with wrought iron, assumes that the observed difference in properties between specimens with and across the direction of rolling is due to slag enclosures. The fact that wrought iron shatters in ballistic test is taken as an indication of the effect of inclusions on the resistance to'shock. Since that time, the development of the metallurgical microscope has shown the discrete nonmetallic inclusions in the iron matrix. Better resolution has brought out the great number of inclusions, and the availability of good microscopes in steel mills and laboratories has constantly drawn more attention to these inclusions. This recent emphasis on inclusions has resulted in studies as to their nature, mode of formation and methods of elimination, such as the work of Wohrman, Dickenson, Herty and Schenk. In addition to the published works, many investigations which have not been published have been carried out by private laboratories and have resulted in the application of specifications intended to limit inclusions in many qualities of steel. Neverthless, a clear understanding of the quantitative effect of inclusions on the physical properties of steel has been lacking. It is the specific purpose of this study to determine the quantitative effect of inclusions on the physical properties of steel that determine its behavior under dynamic stress. The study has shown that a quantitative relation between counted inclusions and impact strength does exist in normalized steels, but that factors other than readily visible inclusions are equally important. Furthermore, the present commercial rating of inclusions is unreliable with respect to counted inclusions or dynamic tests, and this study indicates that the tensile-impact test is more reliable as a measure of quality. General Scheme The general plan of the study follows: (1) To develop or establish a satisfactory measure of dynamic strength; (2) to develop or establish a

Jan 1, 1931

By W. L. Prehn, Adele Chambers, R. L. Slobod

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By R. L. Slobod, W. L. Prehn, Adele Chambers

The centrifuge has been found to be an extremely useful tool for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. The use of the centrifuge for determining the properties of small core plugs has been discussed in the literature,',' but practically no experimental evidence has been presented justifying the use of this method in preference to other methods (mainly disc method) now in use. Data have been accumulated and are now presented demonstrating the advantages of the centrifugal method, some of which are: (1) rapid establishment of equilibrium, (2) excellent precision yielding very reproducible results, (3) availability of high pressure differences between phases, (4) simple operational procedure, and (5) ability to establish connate water, residual oil, or to obtain complete capillary pressure curve in one day or less. A commercially available centrifuge capable of speeds up to 3,800 rpm, and a high speed attachment providing a maximum rate of rotation of 18,000 rpm were used in this work in conjunction with core holding tubes designed specifically for this application. In view of the outstanding advantages associated with the use of the centrifuge the conclusion has been drawn that this method should be used in place of the more tedious, slower, and less reliable disc method for determining capillary pressure curves and for establishing connate water and residual oil in small core plugs. INTRODUCTION The need for accurate values of connate water, residual oil, and capillary pressure curves in reservoir engineering has been recognized for many years, and the extent of the effort devoted toward solving these problems is reflected in the large number of papers3-" which have appeared in the literature during the past decade. Most of the methods discussed in the recent literature employ a porous disc as a semi-permeable membrane to separate two immiscible phases and make pos-ible the application of an explicit difference in pressure between two phases in the core. Thus, in the determination of the capillary pressure curve the wetting phase (water) is displaced by the non-wetting phase (air or oil). Several investigators1,2 have used centrifugal forces to develop pressure differences between phases. As a result of the first work' in this field the conclusion was reached that "the more rapid centrifugal method for measuring irreducible saturation may have equal value, (compared to use of discs) but more work is required to establish this point." This work was followed in 1945 by a more detailed study2 in which the concepts of this experimental work were more clearly enunciated. A method for calculating saturation for any given speed of rotation based on the observed volume of water displaced was developed and a wider application of the method was suggested. The absence of any subsequent pertinent literature on this subject is interpreted as indicating that no additional work has been completed to substantiate or deny the earlier claims and suggestions of promise contained in the original papers on this subject. One purpose of this report is to provide evidence designed to establish the practical value of centrifugal methods in determining core properties such as connate water and capillary pressure curves. It is also our purpose to suggest a broadening of the scope of this tool to include determinations of residual oil by gas or water drives. THEORY AND PRACTICE IN USE OF CENTRIFUGE Hassler and Brunner2 have clearly presented the basic concepts involved in the use of the centrifuge by relating the performance of a small core in a field of high acceleration to the

Jan 1, 1951

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By Joan Melcher

The oil embargo and increasing disillusionment with nu- clear power have put this country's abundant coal reserves in growing demand. Both the government and industry are looking toward increased coal mining, and with this goes an increased interest in new and advanced methods of coal utilization. One advanced coal system stands out among the rest-magnetohydrodynamics (MHD). Its high efficiency, strong probability of sulfur dioxide control, and limited consumption of cooling water place MHD in a unique position to help the power generation industry. Another point in MHD's favor is the capital costs of operation, which are lower than those of other advanced technologies. However, initial costs are higher and realization of a commercial MHD plant in this country may be more than a decade away.

Jan 12, 1977

By A. E. Perkins

fractured ingot will show a complete diagonal structure. If the temperature is lowered, the equi-axed zone is larger and the pine tree growth is less. A small ingot, though, is prone to this columnar structure, even though the casting temperature is kept down. The speed of cooling after solidification is slower in the hollow ingot than in the solid, therefore the granulation, which takes place after the crystals have formed from the liquid metal, is apt to produce larger grains than in the solid ingot. This is not a detriment. The original crystal size is of much more importance. The size of the grains due to this granulation constantly varies in response to mechanical work and subsequent heat treatment. Surface weakness, as shown by seaming and checking on the exterior when working or by cracking in hardening, is in some measure the result of the surface stresses of the ingot when cast. The temperature of the ingot mold or speed of freezing of the exterior of the ingot is of great importance and much seamy and cracked steel is caused by a too quickly cooled skin. Ingots that are turned or milled all over will not seam very much in working, in fact they are practically free from seams, whereas an ingot rolled without a preliminary machining operation is full of seams and cracks, some long and some short. It has been said that these short seams and cracks in the surface of the bar are the result of elongated depressions in the surface of the ingot and that if an ingot is cast very smooth it should give fewer surface defects. This is partly true, but an ingot cast very hot and having a very smooth skin will crack and seam very badly in the mill, as will the surface of an ingot poured very cold, which is very crinkly, because of the low temperature of the metal. The cause of the cracks and seams in one is not the cause of the cracks and seams in the other. The tube method of hollow drill steel manufacture is superior to the older method because of: (1) Greater freedom from external and internal straining; (2) the inherent small crystal size; (3) absence of harmful segregation, resulting in weakness of wall of hole. (4) less liability for steel to crack in inside of hole during forging or hardening; (5) toughening effect, arising from mild steel wall of hole limiting the intense hardening on quenching. Breakage and Heat Treatment or Rock-drill Steel By A. E. Perkins, Pittsburgh, Pa. Actual figures showing the superiority of one section or another are difficult to obtain. In a given size of steel, however, the cruciform sec -tion shows the most breakage; it is inherently a weak section. It contains less steel per foot than any other standard section of the same size and when rolled the wings tend to cool off setting up cooling stresses.

Jan 1, 1922

By James A. Barclay, Ralph C. Kirby

The US minerals posture will be increasingly dominated by three interrelated factors. First, when viewed over the long range, the US supply situation can be expected to steadily deteriorate as demand increases. Domestic high-grade ores have been used up, and other nations compete with the US for world supplies. Second, as environmental awareness becomes more acute, an aroused citizenry is demanding that minerals industries conform their operations to rigorous new standards. Finally, the changing energy situation that confronts the US is forcing an appraisal of energy-use patterns on operations previously guided solely by economic principles and not by national priorities. While future US mineral production and consumption patterns are unclear at this time, it is certain that US demand for minerals will continue to outrun domestic supply. Thus, the US is faced with a challenge of producing more minerals and metals from lower grade resources. Meeting this challenge means a strengthening of US research and development efforts, coupled with their application in the remaining leadtimes available. Some specific examples of how the US Bureau of Mines (USBM) is assisting in the processing of low-grade resources follow.

Jan 6, 1975

By John F. Elliott, Robert D. Pehlke

The rate of reaction of nitrogen with liquid iron and with binary alloys of iron and Al, Cb, Cr, Ni, O, S, Si, and W were measured. The surface active elements, oxygen and sulfur, decrease the rate markedly. The other alloying elements have very little effect on the rate except when they function as deoxidizers, The rates of absorption and de-sorption were found to be equal. Several possible reaction mechanisms which may control the rate are considered. In order to describe completely the behavior of nitrogen in steelmaking processes, the mechanisms of mass transfer between the gaseous and liquid phases, nitrogen and iron, respectively, must be understood. A kinetic study to determine the nature of these mass transfer processes was undertaken, and the results of that investigation are presented in this paper. Specifically, the study was directed toward determining the influence of alloying elements on the rates at which pure nitrogen gas at constant pressure is absorbed and desorbed by liquid iron solutions: A previous paper1 reported measurements of the equilibrium solubility of nitrogen in liquid binary iron alloys. The experimental data are presented and discussed first and then several possible rate limiting mechanisms are considered. PREVIOUS RESEARCH The results of several investigations on the rate of absorption of nitrogen by liquid iron and iron alloys have been reported.2-14 There is little agreement on the rate coefficients among these studies because of the influence of geometry on the experimental system and of the purity of the liquid iron. The rate was found to be influenced by alloying content for the binary liquid iron systems: Fe-Al,2 Fe-C,4,6 Fe-Cr,4,5,8 Fe-Mn,5 Fe-Ni,5,8 Fe-O,9,10 Fe-O,9,10 and Fe-Si.2,6,7,11 Several investigators12"15 have reported that the rate of nitrogen absorption is increased in a reducing gas mixture and decreased in an oxidizing atmosphere. A mechanism for the retardation by oxygen of the absorption of nitrogen has been described by Naeser18 as the formation of an iron oxide film at the gas-metal interface. The film slows the absorption rate until it disolves in the metal, thus permitting nitrogen to enter the liquid iron. Karwat17 discussed the influence of oxygen in terms of the formation of gaseous molecules of nitrous oxide which represent a higher energy form than the nitrogen and oxygen or the oxidizing gas and consequently constitute an energy barrier for the process. Fischer and Hoffmann10 showed that the oxygen markedly reduces the rate of absorption of nitrogen, the rate constant being one order of magnitude smaller in liquid iron containing 0.15 to 0.24 pct 0 as compared to that in melts containing 0.001 to 0.02 pct 0. Although Chipman and Murphy2 reported that the rate of absorption of nitrogen in liquid iron was essentially independent of temperature, Eklund3 found that the rate increases strongly with increasing temperature as did Kootz4 and Saito.5,6 Karnaukhov and Morozov7 also reported a large temperature coefficient, but related it to increased stirring at higher power inputs in an inductively heated system. All of the authors above have treated their results assuming that the reaction is diffusion controlled, that the surface reaction is in equilibrium with nitrogen gas, and that a "first order" reaction takes place. Karnaukhov and Morozov7 and Humbert; who studied the rate of absorption in a closed system by observing pressure changes in the system as a function of time, concluded that their results best fit a diffusion-type analysis. This was further verified by von Bogdandy, Dick, and stranski18 and Fischer and Hoffmann10 who found the initial rate of

Jan 1, 1963

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By J. B. Wagstaff, R. A. Buchanan, J. F. Elliott

High speed photography through blast-furnace tuyeres showed coke particles moving rapidly. Model studies showed a raceway was formed and gave quantitative results which were correlated with actual blast furnaces. Another study showed the similarity between hanging and the flooding of a packed column. This was explored by models. THE combustion zone before the tuyere in an iron blast furnace is a vital region because here are generated: 1—most of the gases on which the furnace depends to carry out its basic operation of reducing iron ore to the metallic state, and 2—the major fraction of the heat required in the nearby regions of the furnace for the various reduction reactions, the fusion of the slag, and the melting of the iron. Since the greater part of the coke is consumed in this region, the descent of the burden must be greatly affected by the characteristics of the tuyere zone. This region then would seem to be a profitable field for study. Fortunately, a view into this important zone is available to the operator through the tuyere peep sight. Here he sees relatively dark pieces of coke "dancing" in the blast. What he sees is of considerable help in interpreting the behavior of the furnace at a given time but the very rapidly moving particles and the intense radiation obscures what is happening very deep in the zone. This investigation was initiated in the hope that a better understanding of the combustion region could be obtained by using a high speed camera with a maximum speed of 3000 frames per sec. It seemed the best practical method of "slowing down" this characteristically violent action within the highly luminous field. Model studies and tuyere probing also have been used to aid in explaining the observed phenomena. Above the combustion zone, but below the fusion zone, there is probably a region in which the coke is comparatively stationary. Here are zones in which the gases must flow up through the granular bed counter to descending liquid slag and metal. There is no easy way to observe this zone in a blast furnace, but model studies have been of some help in explaining the nature of the zone and the laws governing the flow of the fluids involved. The whole problem is difficult and involved and any approach to a complete solution may require long investigation. This preliminary report has been written, therefore, because it is believed that appreciable progress has already been made that would be of interest to others. Tuyere Studies, Chemistry and Kinetics It is well known from the early work of Kinney and coworkers1,2 that combustion of carbon before the tuyeres appears to occur in two zones: Zone A: C + O, = CO2; AH77°F. = — 14,108 Btu per lb of carbon [I] Zone B: CO2 + C = 2CO; H77°F = + 6,183 Btu per lb of carbon [2] Zone A (Fig. 1) is close to the tip of the tuyere and zone B is somewhat farther back; there being a transition region in which both reactions occur. It is interesting to estimate the rate at which coke is burned before a tuyere with a wind rate of 90,000 cfm in a modern furnace having 18 tuyeres. Approximately 0.55 lb of carbon is consumed by eq 1 per tuyere per sec. A like amount disappears by eq 2 for a total consumption of 1.11 Ib per sec per tuyere. Assuming the coke is 85 pct C and has a bulk density of 30 lb per cu ft, this figure can be converted to a total of 1.30 lb of coke with a bulk volume of 0.043 cu ft disappearing per sec per tuyere. At the temperatures prevailing in the combustion zone (according to Kozlovich,³ he maximum is about 3400°F), the rate at which carbon is con-

Jan 1, 1953

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By John C. Shyne, Eric R. Morgan

BORON as a hardenability agent of commercial importance has been the subject of extensive study in recent years. It has been suggested in the past that boron increases hardenability by combining with nitrogen, thus rendering it innocuous.&apos; More recently it has been proposed that boron increases hardenability by reducing the free energy of sites of ferrite and pearlite nucleation.&apos; The segregation of boron to grain boundaries, the primary site of nucleation, would account for the large hardenability effect of minute additions of boron in steel. This grain boundary theory has found general acceptance while the concept of boron as a nitrogen scavenger has been disregarded. However, the interaction of boron and nitrogen in steel is considered to be important to hardenability because boron may be made ineffective by combination with nitrogen.". * The present work was undertaken to examine some of the effects of boron and nitrogen arid their interaction in steel. A base composition of moderate hardenability was chosen. This was a 0.35 pct C steel containing 2.50 pct Ni and 0.30 Mo. This composition was used because it contained no strong carbide, nitride, or Table I. Composition of Steels by Analysis, Wt Pct Steel C Ni Mo 0&apos; B N* Base 0.35 2.50 0.30 0.0012 nil <0.0001 Boron 0.35 2.50 0.32 0.0012 0.0022 <0.0001 Nitrogen 0.33 2.60 0.35 0.0015 nll 0.0052 Boron plus nitrogen 0.35 2.48 0.30 0.0006 0.0020 0.0040 * Obtained by vacuum fusion technique. boride-forming elements. The other alloys examined were modifications of the base composition and contained nitrogen, boron, or nitrogen plus boron. The compositions of the four alloys used are listed in Table I. The alloys were vacuum melted from electrolytic iron, electrolytic nickel, ferromolybdenum, and fer-roboron. When required, nitrogen was added by admitting a partial pressure of nitrogen over the melt after vacuum melting. The alloys were cast into 21h-in. diam ingots and hot rolled to %-in. sq bars. No ingot pattern was discernible on the polished and etched cross sections of the hot-rolled bars. The alloys were normalized at 1650°F, then machined into standard %-in. diam end-quench hardenability test bars. Four different austenitizing treatments were used: 60 rnin at 1550°F, 45 rnin at 1800°F, 30 rnin at 2000°F, and 20 rnin at 2000°F followed immediately by 30 rnin at 1550°F. The 1550" and 2000°F treatments were carried out in duplicate for each of the four steels. In order to prevent surface oxidation the bars were austenitized while buried under charcoal in an atmosphere of argon. After quenching the bars in a conventional end-quench fixture, the hardness surveys were made in the usual fashion on parallel flats ground along opposite sides of each bar. These were ground 0.050 in. deep rather than the conventional 0.015 in., to avoid decarburized or deboronized regions.5 The austenite grain sizes which resulted from each heat treatment were observed metallographically using Vilella&apos;s etch for martensite. The criterion used as a measure of hardenability was the distance from the quenched ends of the bars at which a hardness of RC 35 was observed. This hardness represented the inflection point on the hardness vs distance plot. Fig. 1 shows the hardenability of each steel after the several heat treatments. The duplicate tests demonstrated excellent reproducibility; the distance to Rc 35 was reproduced within 1/16 in. for duplicate test bars. All four alloys had the same grain-coarsening characteristics. Neither boron nor nitrogen had any observable effect on grain size. The grain sizes resulting from the various austenitizing treatments were ASTM 7 at 1550°F, ASTM 4 at 1800°F, and ASTM 2 at 2000°F. The small amount of boron in the boron steel greatly enhanced hardenability when the samples were austenitized at 1550°F. The low hardenability of the boron plus nitrogen steel showed that nitrogen eliminated the boron contribution to hardenability. Both steels containing nitrogen, with and without boron, exhibited lower hardenability than the base composition when quenched from 1550°F.

Jan 1, 1958

By R. B. Lincoln

THE function of a pyrometer protecting tube is to maintain an atmosphere about the thermocouple most favorable to its continued accuracy and long life, and at the same time permit the weld of the couple to attain the full temperature of the area or object being measured. In addition to protecting the thermocouple from the chemical or alloying effects of the products of combustion or bath being measured, the tube must also protect the couple from mechanical injury. The conditions met in practice vary so much that no one material is suitable for all applications. The usefulness as well as the expense of maintenance of a pyrometer system are influenced greatly by a choice of the most suitable protecting tube. The tube must protect the couple without itself becoming too great an expense item. The protecting tube should have the following qualities: (1) A melting point well above the highest temperature to be encountered. (2) Sufficient strength through the entire range of temperatures to hold up its own weight and resist such shock and jar as are unavoidable. (3) It must be impervious to the atmosphere or bath to which it will be subject. (4) It must not give off any vapor injurious to the couple. (5) It must not form any oxides fusible below the highest temperature to be measured. The proper location of the tube in the furnace is almost as important as the choice of material. The tube must be placed as near to the work to be heated .as possible. It must be kept out of the direct path of flame, both because that would give too high temperature readings and because partly burned fuel will destroy the tube faster than the quiet products of combustion.

Jan 9, 1919

By Frank Wilder

THE most important process in a gypsum mill is calcining the crude mineral. There seems, however, to be little progress or change in calcining methods. This would not be surprising if the industry was not, in other ways, developing. The demand for gypsum in its various forms, however, is growing rapidly. The output has more than doubled in six years, while the value of gypsum products, through the introduction of higher priced specialties like wall board, has nearly trebled in the same period. In other industries, under somewhat similar conditions, calcining in rotating cylinders, either by direct or indirect heat, has replaced the method that still prevails in gypsum mills. Efforts were made to use rotary calciners in manufacturing plaster of Paris in the early days of the industry in America; 25 years ago rotary calciners were in use in Germany. At that time there was great diversity of opinion in regard to their merit. In 1923, the output of calcined gypsum in the United States was 3,101,378 tons. About nine-tenths of this material was calcined in kettles, the remainder in rotary calciners. The ratio was about the same 10 years ago. During these 10 years, rotary calcining made rela-tively no gains, and there were no important changes in the construction of kettles. In their manipulation, the only change of consequence was in connection with the length of time that the gypsum is left in the kettle. For wall-plaster purposes, all producers who had not previously done so changed from second-settled to first-settled calcined gypsum, thereby reducing production costs and improving the plasticity and sand-carrying capacity of their plaster. Nevertheless, in the few mills in which they were installed, rotary calciners continue to operate, with possibly one or two exceptions, and to be highly successful. In these 10 years, the Cummer type of rotary calciner has disappeared. All rotaries now used are of the cement-mill type with a diameter of 6 or 7 ft. and length of 80 to 120 feet.

Jan 2, 1925

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey&apos;s determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By C. S. Smith, E. W. Palmer

For several years an investigation has been in progress in the research laboratory of The American Brass Co. to determine the thermal and electrical conductivities of most copper alloys of commercial importance and several of scientific interest. This paper contains such data on the binary alloys of copper with silicon, aluminum, manganese and nickel, and on a large number of ternary or more complex alloys. Some interesting general relationships between the thermal and electrical conductivities for all copper alloys at all temperatures are pointed out. The data for the copper-zinc, copper-phosphorus and copper-tin binary systems have already been published1,2 † except for the electrical conductivity at 200" C., which is given in the appendix of this paper. Literature on Thermal Conductivity of Copper Alloys The papers referred to above contained a summary of the figures available in 1929 for the thermal conductivity of copper alloys. There is given in Table 1 herewith a selection of the data that have appeared since that time. The measurements of Hanson and Rogers3 are particularly interesting since they cover a series of alloys in the alpha solid solution range and show the effect of heat-treatment. Their alloys were tested as annealed castings, and are not therefore directly comparable to the worked alloys measured in the present investigation, although the difference is small. Bailey&apos;s determinations4 were carried out on the alloys used by Lees6 in 1906, and extend his results to higher temperatures. It is most unfortunate that the alloys were not analyzed, for the approximate compositions given are hardly sufficient identification of the material. It is equally to be regretted that neither Hanson and Rogers nor Bailey give data for the electrical conductivities of their samples. Sager6, using the heat-wave method of King, determined the thermal conductivity of copper, nickel and four alloys of the two metals. His results are included in Table 1.

Jan 1, 1935

By Howard S. Bryant

FROM the viewpoint of the oil producer, the oil refiner, the oil marketer, and the investor, in oil securities, a brief picture of the crude oil supply and demand in the present critical season of the year will be timely and interesting. Although crude oil production has been in a comparatively poor statistical position this year, increased sales and sustained refinery and crude oil prices have allowed increased profits for many oil companies. The large amount of crude oil going into storage during the present period of peak consumption, just previous to the major yearly fall decline in consumption, has caused oil producers to make plans to leave the oil in the ground for the present in several of the areas of large flush production. The present moment is looked on as the turning point in the current year.

Jan 1, 1929