Search Documents

By Earl S. Greiner, Eric R. Jette

Although the mechanical and chemical characteristics of certain iron-nickel-silicon alloys have been investigated,1 the available literature shows no results of a systematic investigation of the constitution of this system. 'This paper describes the results of an X-ray investigation of the constitution of the iron-rich iron-nickel-silicon alloys at 600°C. Data 011 the constitution of the included binary systems obtained in other investigations have been correlated with the structure of the ternary alloys. Jette and Foote2 have presented a tentative constitutional diagram of the iron-nickel system. following X-ray studies on quenched specimens. This diagram shows that the alloys at 600°C. containing from zero to approximately 4 atomic per cent nickel consist of a body-centered cubic (alpha) phase, the alloys containing 4 to 24 atomic per cent nickel consist of body-centered cubic (alpha) and face-centered cubic (gamma) phases, and the alloys containing from 24 to Ioo atomic per cent nickel consist of a face-centered cubic (gamma) phase. These investigators recognized that it was not possible to retain the gamma phase in equilibrium by quenching alloys containing less than approximately 25 atomic per cent nickel and that high-temperature X-ray methods were desirable to determine the gamma-phase solubility limit. In a later investigation of the iron-nickel alloys, Owen and Sulley3 determined the alpha-phase solid solubility limit to be 3.5 atomic per cent nickel at 600°C. High-temperature X-ray methods showed the solid solubility limit of the gamma phase to be 14 atomic per cent nickel at 600°C. Since the high-temperature X-ray method should reveal equilibrium conditions in these alloys better than the quench method of other investigators, the results of Owen and Sulley pertaining to the gamma-phase boundary are to be preferred. As the result of an X-ray investigation of quenched iron-silicon alloys, Greiner and Jette4 have shown these materials to consist of a body-centered cubic (alpha) phase containing from o to 26.4 atomic per cent silicon at 600°C. The alloys containing from 26.4 to approximately 50 atomic per cent silicon consist of two phases at 600°C.; namely, alpha and eta. The eta phase corresponds to the stoichiometrical formula FeSi (33.4 wt per cent Si)." The literature pertaining to the constitution of the nickel-silicon alloys has been reviewed by Ackerman,' who found disagreements in the results of various investigators on several parts of the system. Subsequent data on the constitution of the nickel-silicon alloys were reported by oSawa and okamoto.6

Jan 1, 1943

By Kurt Stock

The war caused a demand for enormous quantities of high-grade zinc, which were not available and could not be produced from pure ores in sufficient amounts and in the time required. Redistillation of virgin spelter on a large scale was practiced to supply this demand; this paper gives a full description of the process used by the Oklahoma smelters of the Bartlesville Zinc Co. As the redistillation of zinc has become of historical interest only, having been superseded by the electrolytic process, it was deemed advisable to give expression to this phase of the metallurgy of zinc that, in the past, had never gone beyond laboratory experimentation. THE grades of spelter demanded by the consuming industries were not definitely established until the American Society for Testing Materials undertook to fix specifications, based on the varying percentages of the common impurities (lead, iron, and cadmium) as follows: TOTAL, NOT LEAD, IRON, CADMIUM, OVER. PER PER CENT. PER CENT. PER CENT. CENT. A. High grade 0.07 0.03 0.05 0.10 B. Intermediate 0.20 0.03 0.50 0.50 C. Brass special 0.75 0.04 0.75 1.20 D. Prime western 1.50 0.08 The question which grade was the best for certain purposes and why was left unanswered. The conservatism of the zinc-smelting industry and the unwillingness of the spelter-consuming industries to engage in research work prevented the full benefits being obtained that such standardization promised. The custom smelters, producing spelter in pigs or plates, found it impossible to adhere closely to the established limits on account of the variety of ores treated; and the smelters with long-established and known brands, or those manufacturing their metal into marketable products, like sheet zinc, did not have to abide by the newly established grades based on chemical percentages.

Jan 7, 1924

By Thomas W. Yardley

In many years' experience as a maker and purchaser of cast-iron coated pipe, I have never met with any standard form of specifications for such. Each water-works company, employing a hydraulic engineer, has, under his direction, prepared complete specifications for the particular conditions required; but I cannot find that any two are alike; and each foundry, in bidding for the supply of such pipe, makes the price to cover the conditions' required. I, therefore, have the honor of offering to the Institute a form of specifications for cast-iron coated water-pipe, that may be found useful to water-works companies and others requiring pipe of this kind. The conditions are all reasonable, and can be carried out by makers without additional cost, and with advantage to the purchaser. Section 1 gives the kind of pipe, with its general characteristics. Section 2 specifies that neutral pig-iron shall be used, since such iron possesses the strength required, and is uniform in its shrinkage. Section 5, requiring makers to give the brands of pig-iron used

Jan 1, 1890

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By T. G. Sieber, T. D. Tiemann

The extraction of quartz from siliceous iron ores by dissolution in sodium hydroxide solution has been described in detail in AIME Transactions. l923 data reported covered the temperature range from 230-416°F, where a continuous increase in the amount of silica extracted with increase in temperature was found. It is the purpose of this paper to describe some unexpected results of more recent work exploring principally the range of 500600°F where higher rates and greater amounts of silica extraction were antici-p ted. In brief, the experimental procedure consists in digesting the ore under pressure in solutions of sodium hydroxide, filtering the suspension and weighing and analyzing the dried residue for iron content. The amount of extraction is calculated from the weight loss or from the iron analysis of the residue and that of the original ore.

Jan 1, 1969

By Hokuichiro Ohmachi

INTRODUCTION Metallic minerals have been formed only through complex geologic processes which took place at certain stages of the earth's histrory. Their concentration, abundance, and distribution are, therefore, restricted geologically, and very small in global scale. Ore is a mineral deposit or mineral concentration from which metals can be economically extracted by the contemporaneous technology. By this definition, several factors should be considered before any mineral deposit is regarded as an ore. The grade of mineral concentration and the scale of the reserve are most important. Demand for the metal and its price are the other factors. Advancement of technology in mining and extraction are also vital. Copper, for example, is now commonly extracted from the ores containing less than 0.3% of the metal. However, in the 1700's the common minerable grade was about 13%, and in the 1900's between 5 to 2.5%. This decrease in minerable grade is a function of not only the demand for copper, but also technological progress in mining and metal extraction in this case. Availability of ores has recently been subject to political factors, which were not the primary concern in the past. The petroleum of the Middle East is the prominent example. The metallic minerals are classified into three categories. The first one is the minerals free from these factors mentioned above. Iron and manganese belong to this category. The second category include aluminum, copper, nickel, cobalt, titanium, lead and zinc. These metals can be provided by the future progress in technology which enables the use of lower grade deposits. The third one represents the metals whose occurrence is geologically limited, and, thus, subject to the political factors. Niobium and tantalium are the example. In this article, I discuss these minerals in detail to give an outline of the factors which brought their concentration, distribution and availability. SELECTED MINERAL CONCENTRATIONS Iron Major iron ore deposits are the features of the relics of ancient continental crusts. They are found in all the continents where the Precambrian rocks expose. They do not occur in the oldest rocks (3,000my old) nor in the youngest ones (600my old). They are sedimentary rocks, normally, exhibiting alternations of bands of iron oxides (magnetite and hematite) or iron silicates (especially greenalite), and bands of silica, variously described as jasper, quartzite and chert. The best known banded iron ore deposits exist in the Lake Superior region of the North America, and their distribution extends at intervals to Labrador of Canada. Other examples occur in the U.S.S.R. Brazil, Venezela, India, the mainland China, and southern and western Africa (Liberia and Guines) (Table 1). Recently large deposits have been discovered in the Hammersley region of the western Australia, and northern and central region of Brazil. These ore deposits were originally formed in shallow seas where simple but abundant life existed. After the deposition, enrichment processes , related to tropical weathering, have brought about wholesale removal of silica to produce the deposits of best quality. Ores with 50-60% iron represent the best products in the Precambrian fields. Since local reserves of this high grade ores approach to exhaustion, benefication processes have been used effectively to upgrade much leaner ores (for example, taconite with 20-25% iron in Minesota, U.S.A.). There are two other types of iron deposits. Ironstone, a sedimentary rock containing goethite, chamosite and siderite, first appeared in early Paleozoic times in the stratigraphic record, and reached its Zenith in the Jurassic. Similar bedded iron deposits are found in the belt from the Cleveland Hills to Oxford in England, and in the "minette" oolitic ores of Alsace-Lorraine in Luxenburg and France. The iron content of these ironstones seldom exceed 30%, but they usually contain calcite and are self-fluxing. They also have phosphorous as undesirable impurity. Because of the grade and impurities, they require more fuel than the Precambrian ores. The third type of iron ore is associated with igneous activity and consists of magnetite and some hematite, and apatite. This deposit is believed to be a product of magmatic differenciation. It occurs in Kiruna of Arctic Sweden. The iron ore, therefore, present no global shortage problem. They extend to considerable depths. Their concentration is largest among the metals. If low grades were treated, the resource can be stepped up much substantially. Manganese Manganese is a ferro--alloy metal, thus, essential to the manufacture of sound steel. Manganese comes from manganese oxide and silicate ores. Many minerals contain manganese, but only a few oxides, silicates, and, in some places, carbonates (rhodecrosite) are mined as ore. Types of manganese deposits are bedded, massive,

Jan 1, 1982

By T. E. Evans, C. T. Baroch

ZrB2 was produced in batches of 4 to 6 Ib by interaction of ZrO2, B4C, B203, and carbon at around 2000°C in a simple graphite resistance furnace. Techniques of production are discussed and the final design of a suitable furnace is described in detail. Several other borides were made by the same technique and the process appears to have possibilities for commercial production. N seeking out new hard and refractory com- pounds, many researchers have turned to the investigation of the borides and excellent papers have been published on the properties of these compounds. Few papers, however, have appeared on the techniques and problems concerned with the production of these high temperature substances. This report describes progress made in developing a method for preparing zirconium diboride, ZrB2, on a pilot plant scale. The literature of the borides and other refractory hard metals recently has been reviewed, annotated, and classified so completely' that it is needless to attempt such an outline here. It is enough to say that three borides of zirconium have been reported: ZrB, ZrB2, and ZrB12.2 ZrB2 is the most stable of these and is especially stable in the presence of carbon up to and including its melting point of around 3000°C. Like most borides, it can be prepared in several ways. It can be prepared by synthesis of the elements, but these are expensive and difficult to produce in a high state of purity. Obviously, production directly from the oxides would have decided economic advantages. In electrolytic production such as that of calcium boride,:' the product is recovered as a sludge mixed with electrolyte; and separation of product from adhering electrolyte and regeneration of the electrolyte is an involved and difficult process. The work on borides was started on a small scale in 1948. Late in 1949, Naval Ordnance expressed a specific interest in ZrB2 and the project then centered on this compound. After the usual experimental work necessary in a new field, ZrB2 of good quality was produced by heating mixtures of B4C, ZrO2, B2O3, and carbon to a temperature of about 2000 °C in a resistance-type electric furnace. Over 100 lb was made for experimental use tests, and the method of production probably could be expanded into a commercial operation. A similar process has been described by Kieffer and coworkers.' The main chemical problems were the development of proper charges to insure complete reduction of the elements, determination of the proper temperature range at which these reductions took place, and adoption of techniques necessary to pre- vent inclusion of such impurities as carbon and nitrides. The mechanical problems consisted of developing a simple practical furnace that would attain the high temperatures required and permit use of a controlled atmosphere when necessary and determining of suitable refractories. Both problems were solved by designing a crucible resistance furnace. Crucible Resistance Electric Furnace Attempts were first made to produce ZrB2 in an electric arc furnace, but such a furnace would not provide the degree of carbon control required for producing clean graphite-free borides, so it was decided to try working in a crucible. Obviously, the furnace would have to be constructed of graphite, as the temperatures required are too high for other refractories or heating elements. Crucibles were made by hollowing out segments of graphite electrodes, which were fitted with a cover and clamped between two electrodes so that the current passing through the thin wall of the crucible would generate heat, using the principle of the Helberger crucible furnace."? Preliminary tests with this type of furnace were encouraging and led to the furnace design shown in Fig. 1. The essential components were a thin-walled graphite crucible resting on a graphite block, which formed the lower electrode assembly, and a top electrode assembly swung from a pipe column making contact with the top of the crucible. The space around the crucible was filled with graphite prepared from waste electrodes crushed to about ¼ in. This packing had excellent insulating properties, both electrically and thermally, and could be removed easily and quickly from around the crucible by means of an industrial vacuum cleaner. The largest resistor crucibles were machined from 8 in. electrode stock and were 26 in. long, with a side wall Yi in. thick and a 1 in. bottom. Temperatures were determined optically by sighting down a 1 in. hole drilled longitudinally through the top electrode and the crucible cover. Sealing this hole at the top was a water-cooled brass sight-glass assembly, shown in Fig. 2. An opening was provided for a light flow of helium to keep the sight opening clear of smoke, and a glass prism above the sight glass changed the line of sight to the horizontal for easier reading. More recently, the prism and optical pyrometer were replaced by a photoelectric recording pyrometer. At first the charges were placed directly in the resistor crucible but this meant that everything had to be withdrawn from the furnace every time the charge was emptied. Later, smaller crucibles were made up that could be placed inside the resistor

Jan 1, 1956

THE slag performs two useful functions in open-hearth steel- making. First, it is the means of disposal of all the impurities, save carbon, which are removed from the charge materials in refining the steel, so it must be suited to receiving and retaining as much as possible of undesirable elements with minimum loss of iron and useful alloying elements. Second, the slag serves as a buffer between the flame and the bath and transfers oxygen to the metal at a measured pace contrasted with the violent and difficultly controlled oxidation of the bessemer process. At the same time, the slag is a thermal insulator that limits the rate at which heat can be delivered to the metal from the flame, and a heavy slag blanket thereby serves as a brake on production rates. It has been said with justification that the secret of good steel- making is to make a good slag and the steel will take care of itself. In a broad sense, the subject of slag control includes not only the adjustment of the composition of the slag but also of its relative weight in terms of percentage of the metal-bath weight. The slag is made up essentially of: (1) oxides formed by oxidation of silicon, manganese, phosphorus, and iron in the charge, (2) Si02, MnO, MgO, and other oxides charged as such or introduced incidentally with ores or fluxes or by refractory erosion, and (3) lime charged or fed to the heat to neutralize the "acidic" oxides present (Si02 and P205). Obviously, if practically perfect control were possible over the composition of the charge as well as over the oxidation process during the melting period, both slag weight and composition would be very nearly predetermined; and the control problem would be solved. Unfortunately, only a somewhat imperfect control over these factors is possible, so the operator must begin during the lime boil and continue through the refining period to discover and correct departures from the normal pattern of slag development. To do this as the heat progresses, the first helper must be able to make quick estimates of the composition and physical state of develop-

Jan 1, 1964

Primarily, 1961 was a year for widespread application of tools and techniques which have become operational in the past several years • • • Raising --Raise climbers and climber raising techniques have been improved; narrow veins as low as 55° dip are now being mined from climber raises. Climber modifications include: larger motors, tighter radius curves negotiated, improved lubrication and new methods of stowing the climber during a blast. Climber raises are now ventilated in several ways: a 12-in. diam flexible vent tube behind the climber rail; a 6-in. diam pipe behind the climber rail (with fan); or a 6 to 8-in. diam drill hole along the axis of the raise. In hot raises, these ventilating techniques have resulted in more rounds per shift. When driving raises from crosscut and lateral development, mucking machine loading of raise rock is preferred over slusher ramp loading for the following reasons: a) faster set-up and teardown of climber facilities; b) easier access for climber maintenance, repair and loading of raising supplies; c) area at the bottom of the raise can be kept cleaner. Both wide and narrow veins are mined from 7 x 7-ft climber raises at Butte and at Republic, Wash. At Republic, climber rollers have been modified to support increased weight when driving 55°dip raises • Drilling-The new largebore, short-stroke push feed drills are much faster drilling than previous models and are most satisfactory in hard ground. Although reports on maintenance studies of the new drills are not yet available, increased steel and bit wear and breakage, and increased drill maintenance are seen as potential problems. Mines in Montana and Idaho continue to test rubber-collared drill steel. The fabricating methods used are successful but advantages in increased steel life have yet to be proved. Underground applications of down-the-hole drills continue. Drilling speed and accuracy are reported as the outstanding advantages. Manufacturers are now hopeful of making drills which will operate in any direction. Present applications are for ventilation holes (to 8 in. diam) for climber raises, holes for hydraulic fill distribution, drain holes and "predrilled" raises. Good drilling accuracy has been reported to a depth of 200 ft. Cutting holes in drifting is seen as a future application

Jan 2, 1962

By C. S. Smith

QUANTITATIVE methods were used to good effect in the earliest days of metallography1-3 but they mysteriously passed into virtual disuse until the important paper4 by Howard and Cohen in 1947. Various devices for the measurements of integrated linear intercepts have been constructed, primarily by petrographers. The hydraulically operated stage designed by the writer5 was satisfactory, but prolonged use caused air bubbles to become entrapped, which introduced back-lash. A new stage has been constructed which avoids this defect and provides better integration when measuring directional structures. This utilizes a circular traverse, and integration is achieved by counting electrical pulses produced by a photocell and a light chopper.* The stage is shown diagramatically in Fig. 1 and in photograph, Fig. 2. It is of simple construction. Mounted on a plate with clamps to fit the stage of a standard metallurgical microscope is a worm and 100-tooth worm gear, the latter supporting the specimen to be measured. The worm is manually actuated by a knob which contains inside it three

Jan 1, 1961

By Charles C. Rodd

PRIOR to 1938, proration procedure in Kansas required the physical testing of wells in order to set up a basis for allocating production. Subsequently the use of liquid-level data and bottom-hole pressure data was authorized on certain types of wells as a basis for calculating well capacities, thereby permitting wells to be tested at low rates and with small volumes of production. This paper gives some attention to the equipment used for obtaining liquid-level data but in general it is devoted to the theoretical and physical factors involved in well testing by drawdown methods. These tests are divided into two classifications: (1) liquid-level data used directly to calculate capacities, and (2) liquid-level data and liquid-level measuring equipment used in connection with other data to determine bottom-hole pressure. Equations and calculations for both types of tests are shown. Well capacities calculated from fill-up data have not been used generally but offer a simple means of testing some wells. Theoretical factors and calculations for such tests are shown. IN the state of Kansas, proration laws required that the "ability of a well to produce" be given consideration in state allocation orders and for many years this was the only factor used in prorating the allowed oil. The "ability of a well to produce" was the quantity of oil that could be obtained from a well in a prescribed period, usually 24 hr. Early in the history of State-regulated proration, Kansas operators realized that, unless some restriction were placed upon equipment, the competition between producers to obtain large well "potentials" might result in a race to install the largest pumping equipment. Consequently, restrictions were placed upon the size of tubing and length of pump stroke that could be used in pumping wells during potential tests. Later, restrictions were placed also upon the size of tubing and chokes that could be used in flowing walls. Despite the restriction set-up, better pumping equipment was designed and installed, pumps were improved, and various devices were invoked to obtain high rates of production for short periods of time. By 1937 pumping cycles of forty to forty-five 54-in. strokes per minute were not uncommon, and numerous wells had produced at the rate of 3500 bbl. per day for short periods. Such production was far beyond any rate that could be long sustained. Equipment necessary to take "potentials" was several times larger than that needed for normal producing purposes, and repairs and replacements required by the high pumping speeds were excessive. Also, many operators were beginning to suspect that the high rates of production maintained during "potential" tests were conducive to early water encroachment. By 1938 large-scale physical testing of wells in Kansas ended, the use of the bottom-hole pressure gauge had become common, engineers and operators were becoming familiar with the term "productivity index," and bottom-hole pressure was being used as a factor in allocation in many areas. There were many drawbacks, however, to large-scale use of

Jan 1, 1942

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Owen F. Jensen

CONSTRUCTION of a ground-water supply includes many operations, which do not end with completion of facilities. Evaluations must be made of the quality of water in various areas and the history of production. Following an analysis of geologic, hydrologic, and chemical data there must be an exploratory drilling program and a study of resulting information. When the well is completed a continuous survey of operating records and basic data is necessary, since designs for future wells are varied as more data becomes available for those already completed. As the following discussion must be limited to a single undertaking, the customary procedure will be outlined for development and construction of a ground-water supply in which more than three wells are involved. Parts of this procedure are applicable for all ground-water supplies. Three possible sites were selected for construction of a paper mill. The problem was that the industry daily required approximately 15 million gallons of water of the best quality available; however, if water of the best quality were not available in the desired amount, water of a poorer quality could be used up to half the required amount, about 7 million gallons. In the preliminary survey approximately 1500 to 2000 square miles were covered for each site. Collected data consisted of several hundred electric logs of oil and gas wells; reports by the U. S. Geological Survey on ground-water resources of localities in and near the area; unpublished records of several hundred water wells including chemical analyses of the water produced and drillers&apos; logs of the wells; records of periodic water-level measurements made in observation wells by the USGS; topographic maps drawn up by USGS and by army engineers; and highway and county road maps. A preliminary report based on study and evaluation of these data was presented to the client, recommending the site with the most favorable and economical ground-water conditions. The study indicated that water of the quality and quantity desired could be developed. In this particular area there were indications that the aquifer could be separated into two zones con- taining water of different chemical character. This chemical character varied somewhat with area, but principally with depth, a factor which later proved an economic advantage in design of the well field. After studying the preliminary report, the client weighed other economic factors as well as ground-water advantages and selected a plant site. Authority was given to proceed with detailed study of the chosen area. Evaluation of preliminary data concerning the area indicated that it should be supplemented with additional information derived from actual exploratory drilling and testing. A flexible plan of exploratory drilling was devised so that data obtained as each test hole was drilled could be correlated with existing data and additional test holes could be located and drilled accordingly. Specific data to be obtained from each test hole were: samples of all formations penetrated; the driller&apos;s descriptive log of formations; electric logging surveys; one or more samples of water from selected water-bearing formations; temperature; and water levels and their recovery after periods of production. The area studied in such detail was approximately 400 square miles. Choice of location for the original test holes was based on the preliminary study. The pattern for these test holes was designed to require a minimum number of holes and to allow for interpolation of data between two, three, and four holes. Geologic, hydrologic, and chemical data gathered after completion of the first four test holes showed that the north section was the most desirable in the area, which was then reduced from the original 400 square miles to about 150 square miles for more detailed and intensive study. On the basis of findings from the current test a tentative well field was laid out and a drilling program devised. One test hole was located on the actual plant site and later developed into a small pilot production well equipped with a deep well turbine pump. Water from this well was used for general construction requirements. Another test hole drilled near the pilot production well and adjacent to the proposed route of the well-collection system was used during the pumping test of the pilot production well to determine the degree of interference. From the data thus obtained, calculations were made to determine the coefficients of transmissibility and storage. Three additional holes

Jan 1, 1955

By A. B. Young

T HE smelting industry in Utah is represented by four plants: The Midvale of the United States Smelting, Refining & Mini.ng Co., the Murray of the American Smelting and Refining Co., the Garfield of the same company and the Tooele of the Inter- na.tiona1 Smelting Co. The first two are lead smelters, the Garfield plant is a copper smelter while the last named embraces both a lead and copper smelter. A total daily smelting capacity of over 10,000 tons is represented, of which 4000 tons is lead smelting capacity. With the exception of Tooele, forty miles distant, all of these smelters are within twenty miles of Salt Lake City. Pyrometallurgical operations in this district are con- fined entirely to the production of unrefined bullion, which is shipped east to the various refineries of the respective companies. The smelting industry in this state had its beginning away back in the latter days of the Civil War, many years before the completion of the trans-continental railroad. Ox teams were still bringing their companies of better fixed Mormon emigrants across the plains to the valley of the Great Salt Lake and those in lesser circumstances were still pushing their hand- carts over the same roads to the temporary abode

Jan 1, 1925

By John D. Weibmer

A strong step towards acknowledgement of mining as a skilled trade has been taken by the Tintic Division of Kennecott Copper Corp. In May 2 ceremonies, a pilot program was signed into force which, possibly for the first time in US history, recognizes mining as an apprentice trade and grants journeyman status to those who complete the prescribed training sequence. The apprenticeship standards, hammered out after months of consultation between management, labor, and government, are presently limited only to underground hard-rock mining and only within Kennecott&apos;s Tintic Division, but the architects of the program are confident that the concept will spread-first to other underground operations where miners desire documented evidence of their special skills, then to open-pit and soft-rock operations.

Jan 6, 1977

By R. A. Burmeister, G. P. Pighini, P. E. Greene

An open tube vapor phase epitaxial growth system has been used for large area (multiple substrate) growth of GaAs1-xPx on GaAs substrates. The GaCl-GaCl transport reaction is used with either a GaAs or Ga (nonsaturated) source. Selenium and tellurium have been used for donor impurities, and zinc as an acceptor. The useable substrate area in this system is approximately 20 sq cm. The uniformity of thick-ness of the epitaxial layers are typically better than ±5 pct across a given wafer. Electrical and optical measurerments indicute comparable uniformity in electrical and luminescent properties within a wufer. The application of this system to the large scale pro-duction of GaAs1-x Px for display devices, both discrete and arrays, is discussed. Typical electrical and luminescent properties of light emitting diodes fabricated front material produced by this technique are presented. THE most promising materials currently being utilized for visible injection electroluminescence are GaAs1-xPx, Ga1-xAlxAs, and Gap. All have reasonably efficient emissions in the red portion of the visible spectrum at room temperature; Gap also has an efficient green emission.&apos; At present, GaAs1-xPx has a technological advantage over Ga1-xAlxAs and Gap for display applications, since relatively large (several sq cm) areas of GaAs1-xPx suitable for use in electroluminescent devices may be readily grown by vapor phase growth techniques. In contrast, the preparation of Gap and Ga1-xAlxAs for electroluminescent device applications generally employs solution growth techniques which are at present not well suited for the growth of large areas of uniform thickness and doping level. The capability of uniform growth over large substrate areas and the use of multiple substrates is necessary for the practical utilization of electroluminescent devices. This is particularly important when quantity production or monolithic devices are required. Furthermore, in many display applications arrays of light emitting devices are used, the individual elements of which are of a size resolvable by the unaided eye. Thus the overall dimensions of display are substantially larger than those of most semiconductor devices. It is also necessary to achieve a high degree of control over the growth parameters to attain the required degree of reproducibility of materials properties for electroluminescent devices. In the case of GaAs1-xPx it is necessary to accurately and precisely control the phosphorus content of the alloy, both on a macroscopic and microscopic scale, in addition to the parameters generally associated with epitaxial growth such as thickness and doping level. This value is critical, as it has a major effect on the performance of electroluminescent devices. This paper describes the epitaxial growth of GaAsl-xPx suitable for electroluminescent display devices using a system developed specifically for this purpose, and which contains several novel features. The results of studies of selected physical properties of the epitaxial layers are also discussed. Finally, a brief summary is given of the characteristics of display devices fabricated from GaAsl-xPx grown in this system. EXPERIMENTAL A) Reactants. A number of techniques suitable for the vapor phase epitaxial growth of GaAs1-xPx have been reported in the literature.&apos;-&apos; The method selected for this investigation is that in which the Ga is transported by the GaC1-GaCI3 reaction in an open tube process. The results reported here were obtained using either the combination of GaAs, AsC13, and pH3, or Ga, AsH3, pH3, and HC1 as the initial re-actants.* The ASH3 and pH3 were obtained as dilute *Several different sources of supply were used for these reactants, y~elding comparable results._____________________________________________________ mixtures in HZ; the HC1 was obtained from the reduction of AsC13 by Hz at elevated temperatures. Both selenium and tellurium were employed as donor impurities, and zinc as an acceptor impurity. Selenium was introduced in the form of H2Se, tellurium in the form of tellurium-doped GaAs, and zinc in the form of diethy1 zinc. B) Apparatus. The prinicipal difference between the apparatus used in the present study and that of Tietjen and Amick,8 in addition to size and other related design features, is that RE induction heating is utilized in place of resistance heated furnaces. Induction heating was selected for this application because it appears to have several advantages, including: 1) It is possible to keep all fused silica portions of the apparatus at temperatures well below those of the reaction zone, thus minimizing a possible source of contamination. 2) The thermal mass of an induction heated system can be made small, thus reducing the total time required for the growth process. 3) Sharp temperature profiles (desirable for high deposition efficiency) are easily achieved. 4) The volume of the system for a given substrate area can generally be made smaller than a comparable resistance heated unit. This results in shorter time

Jan 1, 1970

By G. R. Speich

The distribution of carbon and the type of substructure in iron-carbon martensites containing 0.02 to 0.57pct C has been studied in the as-quenched condition and after tempering at 25" to 700°C by using electrical resistivity, internal friction, hardness, and light and electron microscope techniques. in marten-sites containing less than 0.2 pct C, almost 90 pct of the carbon segregates to dislocations and to lath boundaries during quenching; in martensites containing greater than 0.20 pct C, appreciable amounts of carbon enter normal interstitial positions located far from defects. Tempering martensites with carbon contents below 0.20 pct at temperatures below 150°C results in additional carbon segregation to dislocations and to lath boundaries but no carbide precipitation whereas -carbide precipitation occurs in martensites with carbon contents exceeding 0.2 pct. Above 150°C, a rod-shaped carbide (either Fe3C or Hagg) is precipitated in all cases. At 400°C, spheroidal Fe3C precipitates at lath boundaries and at former aus-tenite grain boundaries. At 400" to 600"C, recovery of the martensite defect structure occurs. At 600" to 700°C, recrystallization of the martensite and Ost-waW ripening of the Fe3C occur. The effects of the carbon segregation that occurs during quenching and the subsequent substructural changes that occur during tempering on martensite tetragonality, hardness, and precipitation behavior are discussed. A mathematical analysis of carbon segregation during quenching is presented. RECENT studies of the strength of low-carbon martensitel-4 emphasize the importance of carbon segregation to the martensite lath boundaries and to the dislocations contained between them during quenching. Unfortunately, very few studies of the tempering of low-carbon martensites have been conducted, so the exact nature of this segregation is poorly understood. In fact, most early tempering studies5,6 were restricted to carbon contents greater than 0.20 pct. Moreover, these studies did not determine the amount of carbon segregated to the martensite substructure during quenching so that the initial state of the martensite was not established. Aborn7 studied the precipitation of carbide in low-carbon martensite during quenching but did not establish whether carbon segregation occurs prior to carbide precipitation, nor did he study the subsequent tempering sequence in detail. In the present work we have used electrical resistance and internal friction measurements, supplemented by electron transmission microscopy to establish the carbon distribution in as-quenched specimens. Specimens thin enough to avoid carbide precipitation (but not carbon segregation) were employed. The redistribution of carbon on subsequent tempering below 250°C was followed by measurements of elec- trical resistance. Additional studies were made on specimens tempered at 250" to 700°C to elucidate the overall tempering behavior of low-carbon martensites, including the formation of cementite and recrystalli-zation of the martensite. EXPERIMENTAL PROCEDURE Eight iron-carbon alloys with 0.026, 0.057, 0.097, 0.18, 0.20, 0.29, 0.39, and 0.57 wt pct C were prepared as 8-lb ingots by vacuum melting. Typical impurities in wt ppm were 40 Si, 20 Mn, 30 S, 10 P, and 10 N. These alloys were hot rolled to 3 in. plate at 1095°C) (2000°F). The hot-rolled plates were surface ground to remove scale and the decarburized layer, then cold rolled to 0.010 in. sheet. Specimens cut from the sheet were austenitized for 30 min at 1000°C (1830°F) in a vacuum tube furnace in which the pressure did not exceed 2 x 10-3 torr. Chemical analysis of specimens after austenitization indicated no decarburization at this pressure. Immediately before quenching, the furnace was filled with prepurified helium. The specimen was then pushed rapidly through an aluminum foil gasket, which sealed the bottom of the furnace, into an iced-brine bath (10 pct NaC1, 2 pct NaOH). The quenching rate at the M, temperature is about 104&apos;c per sec for 0.010 in thick specimens, as calculated from Newton&apos;s law of heat flow2 using a heat transfer coefficient of 25 ft-&apos;. This quenching rate is sufficiently high so that all the alloys transformed completely to martensite throughout the entire 0.010 in thickness and no carbide precipitation occurred in the martensite. All specimens were immediately transferred to liquid nitrogen after quenching and stored there until needed. Tempering below 250°C (480°F) was done in silicone oil baths thermostatically controlled to *;"C. Tempering above 250°C was done in circulating air furnaces or lead pots with the specimens contained in evacuated silica capsules. Electrical resistance was determined by measurement of the potential drop across both a standard resistance and the specimen, connected in series. All resistance measurements were made in liquid nitrogen (77K, -196°C) to minimize thermal scattering of electrons and thus maximize the contribution of impurity scattering to the resistance. Specimen dimensions were 5.10 by 0.19 by 0.025 cm. Although the precision in the electrical resistance measurements was +0.1 pct, the electrical resistivities could only be measured with an accuracy of +5 pct because of uncertainty in the specimen dimensions. Internal friction measurements were performed in an inverted pendulum apparatus at vibration frequencies of either 1.9 or 66 Hz. The specimen dimensions were 5.10 by 0.375 by 0.025 cm. Hardness measurements were made with a Leitz-Wetzlar microhardness machine with loads of 100 g. Specimens were examined by light microscopy after etching in 2 pct Nital and by electron transmission microscopy after preparation of thin sections by electrolytic thinning in a chromic-acetic acid solution.

Jan 1, 1970

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940

By Joseph P. Kittredge

At the time this matter first came up in 1912, the National Malleable and Steel Castings Co. had seven basic-bottom open-hearth furnaces in its plant at Sharon, Fa., using fuel oil, then costing about 2½¢ per gallon. The fuel was satisfactory but its cost fluctuated widely, therefore the use of pulverized coal, which had been successful in the cement industry and in some metallurgical furnaces, was suggested. After a thorough investigation, and an actual trial on one of the open-hearth furnaces, to be certain that the siliceous ash in the coal would not seriously affect the basic slags, the management of this company approved its adoption and a complete installation was started. The conclusion had been reached that the success of the operation depended on pulverizing the coal to greater fineness than had thus far been accomplished, and all equipment was chosen with this in mind. A coal drier was deemed essential, and one of ample capacity and efficiency was selected, which has done all that was expected of it, working without failure and with very small maintenance cost, and is still in operation. Pulverizers The company demanded a pulverization of at least 90 per cent through a 240-mesh screen, with consistent results, and a machine was chosen that was grinding other materials than coal to the fineness desired. The control of fineness was obtained through a vacuum separator, and was governed by the size of the separator and the number and construction of the valves necessary to expand and direct the air current. These valves can be set to obtain any degree of fineness desired, and the result is consistent. Two machines were installed, each capable of producing 2½ tons per hour, 95 per cent through 240 mesh. These machines have done everything expected of them, have run continuously, and are still in operation. An examination of some of our pulverized coal by elutriation and microscopic measurement disclosed that a 1-lb. lump of bituminous coal,

Jan 1, 1940