Search Documents

By U. F. Kocks

SINGLE slip and a single parallel array of edge dislocations have been obtained in silicon single crystals by homogeneously bending them in a four-point dead-loading device at 1000°C around the [211] axis with [253.] as the tensile axis which encloses an angle of 40° with the glide plane. Other orientations or lower temperatures proved unsuitable. The homogeneity of the bending was checked by the method shown in Fig. 1. The chemically polished specimen was exposed to parallel light from a microscope-stage lamp. The sharpness of the focus of the reflected light is an approximate measure of the circularity of the sample. This method permitted the determination of the actual radius of bent specimens within 10 pct accuracy. The etching solution developed to show up dislocations consisted of the following volume parts: 2 HF, 1 HNO,, 2 CH,COOH, 1 a solution of 5 wt pct of CuNO, in water (Rosi'). The acetic-acid content was adjusted to produce fine well-defined etch-pits in about 2 min at room temperature. The effectiveness of the etch did not depend on the crystal-lographic orientation of the face etched. The number of etch pits produced after a given deformation was checked in the usual way against the Cahn formula' and showed good agreement. As it is to be expected from the orientation of the primary system there are slip steps on the top and bottom faces but not on the side faces (perpendicular to the bending axis), whereas etch pits appear on the side faces but not on the top and bottom faces. This is different only for occasional dislocations of a secondary glide system. All the micrographs included have been taken in places where the most of secondary glide could be seen. From this it is evident that in the homegeneously deformed region the number of secondary dislocations was less than 1 in 1000 of the primary type. Dislocation Distribution—A series of tests with varying amounts of deformation is shown in Figs. 2(a-c). An observation that can readily be made from these pictures is that the linear density of dislocations within slip lines is relatively constant and independent of the amount of deformation. "Slip line" in this context is understood to mean a line that is a straight connection of individual etch pits. The heavily pitted bands which can be seen in each of these three pictures may be resolved fairly definitely, at higher magnifications, into many "slip lines" the distance between them being of the order of 0.5p The distance between dislocations in slip lines is of the order of 2p and it is also fairly constant in going from the neutral zone outward. The higher over-all dislocation density in the outer regions of any sample and the higher total number in a more heavily deformed sample, are effected by a larger number of "slip lines." The relative constancy of the dislocation distance within an individual slip line is surprising. The absence of pile-ups" may imply, if there is no rear- rangement on unloading," that there are no substantial obstacles to slip in this case. It seems that the equilibrium distribution of the dislocations in each active slip plane under the higher external stress on

Jan 1, 1959

By Frederick H. McDowell

Notwithstanding the rapidly increasing use of copper, due to the extension of its applications within the last few years, the fact of its continued steady decline in price stands prominently forward. Nor have we far to look for the cause. The opening up of the vast copper-deposits of our Western States and territories is the metallurgical event of the last five years. We must not forget, in looking at the new field, the changed conditions under which the metallurgist must work, as compared with the previous history of copper-smelting. Until quite recently, the copper-plants of the country were few in number; and the concentration of industry implied in this circumstance, allowed many practices which must be considered as inapplicable to the conditions offered at the many mines which have of late become such important factors in our copper-production. Thus the old style of smelting the ore for matte in brick furnaces, involving great expense and time in their construction, while deservedly losing repute even in its old strongholds, in comparison with water-jacketed smelters, is still in some cases adhered to. But to put up such furnaces at Western mines would be out of the question. The large and continual need of brick for relining and repairs acts as an effectual bar, when such furnaces come into competition with the light, portable, and easily managed water-jacketed smelters of improved types. It is owing to the present unusual activity, manifested in the opening up of new copper-properties and the erection of plants for working them, that any improvement in furnace-construction is of especial interest and importance. The method in which processes are copied without variation in the rapid growth of metallurgical interests, has already been strikingly exemplified in the history of

Jan 1, 1885

By T. S. Liu, E. A. Peretti

A LITERATURE survey of the In-Sb system, which was made before a study of the binary diagram was undertaken, revealed that the intermediate phase InSb existed and that its crystal structure is face-centered cubic of the zinc blend type. In 1929 Goldschmidt' determined the lattice constant for InSb and obtained a value of 6.452A. A more recent value, 6.461A was reported by Iandelli2 in 1941. The purity of the indium used was not very high, however. The indium used by Iandelli contained 2 pct Ge. In view of this fact it was decided to remeasure the lattice parameter using high-purity indium (99.97+ pct In) and spectrographically standardized antimony of the highest purity available (99.91 pct Sb). Specimens corresponding to the InSb composition were made by carefully weighing the ingredients on an analytical balance and heating them in vacuo in a quartz tube at 700°C. As melting losses were negligible, the alloys were not analyzed chemically, but the intended analysis was taken as being accu- rate. Powder samples were prepared by either filing or crushing of the brittle alloy, followed by screening at 325 mesh. The powders were then annealed at 400°C in evacuated capsules for about an hour. X-ray photograms were taken with a Debye and a back-reflection focusing camera, using characteristic cobalt K. radiation. Lattice parameters were calculated by Cohen's³ method. The results of a Debye pattern and of a back-reflection pattern at 25°C are given in Tables I and 11. The lattice parameter at 25 °C is 6.47602A.

Jan 1, 1952

By W. H. Bassett

IN their paper on the directional properties in cold-rolled and annealed commercial bronze,1 Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45° ears" and "90° ears. " Fig. 1 shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45° ears, while that annealed at 950° C. showed FIG. 1.-CUPRONICKEL, 0.032-in. GAGE, CAST WITH MAGNESIUM. ANNEALED AT TEMPERATURES INDICATED (DEGREES CENTIGRADE) AND CUPPED. long "90° ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be.

Jan 1, 1932

By R. G. Vardiman, M. R. Achter

THERE has been interest recently in the conditions under which dislocation pipe diffusion may be observed. In order to extend the measurements to temperatures below Tm/2, where pipe diffusion becomes more important, a chemical sectioning technique was developed for silver single crystals which makes possible the removal of layers of 100A or less. The procedure is briefly as follows. Silver single crystals of 99.995 pct purity were cut in the form of discs t by 4 in., electropolished, and electropolated with Ag110 to about 1000A thickness. The thickness was determined by calibrating the activity with the weight of heavier platings, up to 10,000A. Both diffused and undiffused samples were sectioned in a two-step process. Reaction with a solution of iodine in alcohol formed a thin, even layer of AgI, which was then dissolved in a KCN solution. The reaction rate of the iodine solution varied slightly over a period of time, so that the thickness of the stripped layers, while quite even and regular for a given specimen, ranged from 65 to l00W for different specimens. This variation was checked by using a thickly plated standard with each run. Layer thickness was determined from undiffused samples by the point where the layer activity drops to half the maximum. This maximum intensity also provides, with appropriate corrections, the initial concentration per layer co. Because of the small penetration distances, it is necessary to use the exact solution of Fick's law for a source of finite thickness.' For a plating of thick- where c is the concentration at depth x. flj the error function, D the apparent diffusion coefficient, and t the time. The diffusion coefficient was obtained from the concentration-penetration data by extrapolating to x = 0 where c/co = erf h/2(Dt)1/2 Enough points were taken to impart confidence in the accuracy of the intersection, generally about ten layers. Four temperatures were used as in Table I. For best accuracy, t and h were chosen to give values of the parameter (Dt)1/2/h between 1.0 and 1.7. A typical concentration-penetration curve is shown in Fig. 1. The diffusion coefficients calculated from Eq. [I] are plotted in Fig. 2. For comparison, the high-temperature data of Tomizuka and sonder 2 which go down to 630°C are plotted as the solid line 2(a) from their expression D = 0.40 exp (-44,090/RT). Also for comparison, the lowest temperature point of Hoffman and Tumbull3 is plotted. It is apparent that our data diverge appreciably from the high-temperature extrapolation by 373°C. A better straight line fit for the low-temperature portion is obtained by subtracting the extrapolated volume diffusion coefficient from the apparent. or measured coefficient, and plotting the difference, curve (h) of

Jan 1, 1970

By K. C. Hong, R. B. Jensen

The problem of determining the optimum set of steam volumes and cycle lengths for a single well undergoing multicycle steam stimulation in order to maximize the cumulative discounted net income has been formulated mathematically and programmed for a digital computer. The mathematical fonnulation of the problem and the method for its solution are discussed in this paper. The oil production performance during each stimulation cycle was simulated by either a constant percentage or a harmonic decline. Using simple analytical expressions for production performance, the cumulative discounted net income and cumulative time of operation were related to the pertinent process and cost parameters and two principal process control variables (cycle length and steam injection volume). The discrete maximum principles was used to transform the equations for cumulative time of operation and cumulative discounted net income into a set of simultaneous equations. The simultaneous equations then were solved by trial and error on a digital computer to determine the set of cycle lengths and stem injection volumes that gives maximum cumulative discounted net income over the project life. INTRODUCTION Steam stimulation is a process for improving the oil recovery rate from wells producing high-viscosity crudes. The process is applied on an individual well basis and is executed in a series of cycles, each consisting of three phases: steam injection, soaking (steam condensation), and production. Significant increases in production rate following the stimulation operation result from heating the reservoir around the wellbore. As heat is removed with produced fluids and dissipated into nonproductive formations, the production rate declines, usually to near the prestimulation value. Typical production responses are given in case histories reported by Owens and Suter,l and are depicted in Fig. 1. Duration of the production phase is equal to the time for the oil production rate to decline to some specified value and is called the cycle length. (Cycle length is defined as the producing portion of the cycle and does not include the downtime required for steam injection and soaking operations.) Termination of the production phase coincides with the start of steaming for the next cycle. The process is continued, cycle by cycle, until it becomes unprofitable. Models 2-4 have been developed to simulate behavior of a single well during one cycle of steam stimulation and have been used to investigate the effects of system and operating conditions on the production responses. However, these investigations have not shown how the models can be used to determine a most profitable set of operating conditions for a multicycle stimulation project. Perhaps these models are too complicated mathematically to be adapted readily to an optimization study. This paper presents a method for optimizing a multicycle steam stimulation project based on simple production performance models. First, the performance of a steam-stimulated well during each cycle was simulated by either a constant percentage or a harmonic decline model. Using these simple analytical expressions for production performance, the cumulative discounted net income (before tax) and cumulative time of operation for each cycle were related to the pertinent process and cost parameters and two process control variables—the cycle length and the steam injection volume. Finally, the profit function to be maximized was formed. The analogy between the above problem and problems of optimizing multistage decision processes that have been reported extensively in the chemical engineering literatures5-10 in recent years has led this investigation to the use of the discrete maximum principle.5-7 This principle was used to transform the equations for cumulative discounted net income and cumulative time of operation into a set of simultaneous equations characterizing the optimum operating conditions in terms of the two control variables. These equations

Jan 1, 1970

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By C. P. Parsons

Caliper logging is a practice of measuring the variations in the diameter of the open hole in a well. This information is useful for many purposes, among which are: Determining the volumetric capacity of the portion of open hole to be cemented; the amount of gravel to be used for gravel-packing a well; the size and location of seat for a packer to be placed in a well; studying the effects of nitroglycerin shots; studying the effects of acidizing; studying the cause of drill-pipe failures; studying drilling technique; geological correlations. This is a new practice in oil fields and is eliminating considerable guesswork. Introduction Caliper logging of the open hole in oil wells, recently introduced and now showing initial results in many sections of the country, is providing information that is filling a long-felt need in oil-well cementing and in numerous other oil-field practices. Briefly, it measures the variations in diameter, of the open hole in a well. This direct physical measurement of the strati-graphic profile has considerable value for subsurface interpretations by the geologist, engineer, driller and others charged with the responsibility of properly completing and repairing oil and gas wells. The caliper shown in Fig. I is run into a well in closed position. The four arms are released when logging is to start. These arms are independent of each other. As the calipers are pulled upward through the open hole, the arms are like nimble fingers feeling the changing profile of the hole. This mechanical action is in turn converted into an electrical circuit, which is connected to a recording mechanism at the surface. a. Lowered into well in closed position. b. Arms released. Readings are made while caliper travels upward. Direct recording is made at surface, in inches. The recording of the diameter of the hole is directly in inches.

Jan 1, 1943

By H. Warlimont

Precipitation of cementite plates from carbon-rich austenite gives rise to localized formation of martensite in the matrix next to the precipitate upon quenching. The growth of this martensite is urmsually restricted. A distinct lattice relationship is found between this martensite and the cementite phase. It is concluded that the martensite is nacleated in the region of lowest carbon concentration at the austenite-cementite integace, with low-energy matching to the cementite lattice. The restriction of the growth of the martensite phase to the vicinity of the cementite plates can be explained by misfit in the austenite -martensite glissile interface and the uphill carbon gradient in the austenite. The investigation was carried out by light- and electron-microscopy and by electron-diffraction of thin foils. THE precipitation of cementite from carbon-rich austenite gives rise to a localized formation of martensite in the matrix next to the precipitate upon quenching. This behavior has been described previously by A. B. Greninger and A. R. Troiano1 for a 1.78 pct C steel ("pseudomorphic martensite"), and by A. Hultgren2 for a Fe-0.99 pct C—5.20 pct Mn steel. By measuring the axial ratio of the martensite phase,' it was found that the carbon content of this martensite was lower than that of the martensite which formed without prior partial transformation to cementite. Therefore, it was concluded that lowering of the carbon concentration in the matrix next to the precipitate raised the M, temperature locally and thus led to nucleation of martensite at the ce-mentite-austenite interface. However, the restriction of the growth of the martensite phase to the vicinity of the cementite plates cannot be explained by localized carbon impoverishment alone. Under ordinary conditions a martensite plate which has been nucleated in a favorable site can continue to grow until it encounters a physical barrier, or until it encounters a compositional barrier in the matrix, where the total free-energy change for the reaction is not negative, since it has been shown by numerous experiments that the activation energy for growth of ordinary martensite is virtually zero.' An investigation was conducted by transmission electron microscopy and electron diffraction to study this extraordinary martensite. It was expected that crystallographic in addition to compo- sitional conditions caused this abnormal mode of martensite formation. MATERIAL AND PROCEDURE An Fe-C-Mn alloy containing 1.15 pct C and 5.1 pct Mn was used for most of the experiments. For metallographic work, specimens 15 by 15 by 3 mm were used. For preparation of thin films, the initial specimen size was 15 by 15 by 0.7 mm. The heat treatment of each specimen consisted of austenitizing for 1/2hr at 1100'~ in an argon atmosphere, subsequent isothermal holding in a lead bath at one of a series of different temperatures, and, finally, quenching into brine at room temperature. For metallographic examination, the specimens were mounted in bakelite (slight tempering effects resulted from the heat in the mounting press) ground, polished, and etched in nital. Thin films for transmission electron microscopy and electron diffraction were obtained by grinding the specimens to approximately 0.2 mm thickness and subsequent electrolytical thinning. The orientation relationships were evaluated from sets of electron micrographs and selected-area electron diffraction patterns of single units of the transformation products and the adjacent matrix. RESULTS In the alloy which was used for the experiments, proeutectoid carbide precipitates over a wide tem-

Jan 1, 1962

By Charles Fairhust

Although the term 'rock mechanics' started to become popular about the time of the First U.S. Rook Mechanics Symposium in 1956, study of the mechanical behavior of rock certainly pre-dates this event. Bucky, Phillips, Von Karman, Fayol, Galileo...the list of significant contributors can be traced back over centuries, - not surprising for the oldest structural material used by man. Started with a strong mining orientation by the Colorado School of Mines, University of Minnesota, and Pennsylvania State University, joined soon after by Missouri School of Mines and the University of Texas, the Annual U.S. Symposium on Bock Mechanics has evolved into the main U.S. form for discussion of all aspects of rock mechanics, basic and applied - tectonophysics to comminution; near-surf ace foundations to deep mine support design. Although dominantly a U.S. event the annual symposium has benefitted from regular and important contributions from abroad. It would be presumptuous to attempt a comprehensive statement of significant developments over the 25-year history of the U.S. Bock Mechanics Symposium. This anniversary address will attempt instead to present a personal view of developments that appear to be of broad general significance and that may indicate directions for the future. Among the developments to be discussed in the address arc the following: - Energy Basis of Book Fracture Early rock mechanics investigators often overlooked the important distinction between a failure initiation stress and structural collapse. Although essentially synonymous in the

Jan 1, 1984

GERARD B. ROSENBLATT,* Salt Lake City, Utah (written discussion?). -Mr. Eschholz attacks this problem from what appears to me to be the proper angle. He does not limit his viewpoint to the attainment of ideal results under conditions approximating laboratory practice, but rather discusses actual commercial conditions that must be maintained in large-scale operations, where continuity of service without expert attendance is one of the prime considerations. I am of the opinion that Mr. Eschholz has not given sufficient consideration to the commercial possibilities of what he describes as System B, the use of low-tension a.-c. industrial or lighting circuits for supplying power to Cottrell treaters through the medium of a step-up transformer and a synchronously driven rectifier, without the use of motor-generators. It is true that, to date, few installations on a large scale have used this system, but I believe that when the conditions of power supply are suitable, and when proper precautions are taken, this system can be used successfully and to advantage. where at present it is considered necessary to use motor-generator sets. In the average commercial Cottrell installation of any size, the motor-generator set is used for two purposes: (1) To isolate the industrial supply circuit from the Cottrell circuit. (2) To. afford, an easily operated and smooth system of control for the Cottrell treater voltage With proper engineering, both of these objects can be accomplished without the use of motor-generator sets.

Jan 10, 1918

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

By C. M. Tucker, K. R. Van Horn, W. P. Sykes

Recent investigations of the molybdenum-carbon alloys have been reported by Becker and Ebertl,‡ Westgren and Phragmén2, T. Takei3, and H. Tutiya4. Takei3 studied the Mo-C system by employing metal-lographic and X-ray methods, and the other publications described the determination of the crystal structure of the molybdenum carbides. In exploring this system by a technique previously applied to the tungsten-carbon series5, the results of Takei were confirmed with two definite exceptions; i.e., first the composition of the eutectic, and second the nature of the carbon-rich intermediate phase. Consequently, a more thorough examination of the molybdenum-carbon constitution was initiated in an effort to correlate the data supplied by the microstructures, diffraction patterns and chemical analyses. Metallographic Investigation A briquette of molybdenum powder when heated in a carburizing atmosphere at 1500" to 1600" C. for several hours develops the carbon-rich layer shown in Fig. 1. The carburization was accomplished by placing the briquette in a carbon tube, which was heated in the hydrogen atmosphere of an alundum muffle wound with tungsten resistor. While the macrostructure indicates two distinct shells, and suggests the possibility of two carbon-rich phases, no evidence of this condition could be detected by the microscope, which revealed but one high-carbon constituent. This carbide forms next to the molybdenum as a relatively dense, light-colored zone (Fig. 2) which passes abruptly into an outer layer of spongy texture. As will be noted later, only one intermediate phase was observed in the X-ray photograms prepared of different locations in the carburized zone. The metallographic structure at the inner border of the shell, reproduced in Fig. 3, shows a marked porosity accom-

Jan 1, 1935

Tars Committee is the result of a desire of the authorities in charge of the publications of the four national engineering societies to co-operate in this matter. The members of the Committee are the following: Charles WarreN Hunt, Secretary of the American Society of Civil Engineers. D. S. Jacobus, Vice-President of the American Society of Mechanical Engineers. Joseph Struthers, Assistant Editor of the American Institute of Mining Engineers. CaRy T. Hutchinson, Chairman of The Editing Committee of the American Institute of Electrical Engineers. This Committee has held several meetings; it seemed advisable, at the outset, to limit its discussions closely to the general subject of abbreviations. Further, it seemed best to formulate a few general rules to be followed in making abbreviations, rather than to compile a list of forms to be recommended. The Committee decided to limit the subject more narrowly by considering only abbreviations to be used in the text, or general reading-matter, arid not those to be used in special matter,

Jan 1, 1905

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By William J. Priestley

In the manufacture of gun forgings and other steel parts that, in service, are subject to sudden high stresses and shocks, it is most desirable to use steel possessing the greatest toughness and ductility possible without sacrifice of strength. In order to obtain this condition, it is necessary to procure steel that shows the highest possible elongation and reduction of area without lowering the tensile strength and clastic limit. Proper heat treatment of the steel can control this condition within certain limits. When heat treatment has failed to produce the desired results, metallurgists have used steels containing molybdenum, zirconium, vanadium, chromium, tungston, etc. The purpose of this paper is to describe a method by which these desired physical properties may be procured—by the elimination of certain impurities that inherently exist in steel made by the open-hearth process, and without the use of expensive alloys. Design of Gun Forgings In the manufacture of gun forgings, a certain elastic limit is fixed by the designer, and the walls of the gun arc made of the proper thickness, allowing a suitable factor of safety for the high stresses and sudden shocks that occur during gun firing. The clastic strength of the gun is about 1.4 times the stress set up at any point along the bore of the gun during firing with the maximum powder charge. As the stresses set up in the walls of the gun during firing are mostly "tangential," all physical tests are taken in this direction. Due to the length of the forgings, these tangential test bars are always taken at right angles and transverse to the direction of flow of the metal in forging. Furthermore, test bars taken across the grain of the metal will more frequently expose defects and foreign inclusions in the steel than will bars

Jan 1, 1922

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have given much information concerning the miners, also I have discussed the choice of localities for mining, for washing sands, and for evaporating waters; further, I described the method of searching for veins. With such matters I was occupied in the second book; now I come to the third book, which is about veins and stringers, and the seams in the rocks1. The term "vein" is sometimes used to indicate canales in the earth, but very often elsewhere by this name I have described that which may be put in vessels2; I now attach a second significance to these words, for by them I mean to designate any mineral substances which the earth keeps hidden within her own deep receptacles.

Jan 1, 1950

By V. V. Valleroy, A. J. Cornelius, B. T. Willman, G. W. Runberg, L. W. Powers

This paper reports the results of an investigation into the use of steam as a recovery agent. High oil recoveries by steam, as much as 100 per cent greater than by water flood, were demonstrated in laboratory linear cores. The principal mechanisms responsible for the additional oil have been identified as (1) thermal expansion of the oil, (2) viscosity reduction and (3) steam distillation. Although the first two also enhance recovery by hot water flood, they are effective with steam injection at lower volumes of produced fluids. Steam-zone residual oil saturation is independent of initial saturation. Recovery by steam is greater for lighter oils because they contain a greater fraction of steam-distillable components. Equations for the steam-zone advance in a radial homogeneous system are presented; these show the effect of reservoir parameters. The displacement in the hot liquid region moving ahead of the steam front can be estimated by a calculative procedure which is suggested. The method which takes account of the temperature gradient is applicable also to a regullar hot water flood. INTRODUCTION Considerable industry interest in the application of heat to petroleum reservoirs as a means of increasing oil recovery has been evident in the past few years. Three thermal methods which have attracted interest are (1) the injection of saturated steam, (2) the injection of hot water and (3) the injection of air into a formation to support combustion within the reservoir. Much has been published in recent years on underground burning, and there have been several papers on hot water injection. Although there are several early reports1,2 on steam injection, no recent experimental studies have been published on this recovery method. In our early thermal methods research, a marked improvement was found in oil recovery by steam injection compared with recovery by water injection in the same system. An investigation subsequently was undertaken to obtain quantitative information from which to evaluate steam injection as an oil recovery method. In addition, it was desired to investigate the recovery mechanism of hot water as compared with that of "cold" water and steam injection. An understanding of the mechanisms by which these processes operate would generally define favorable field conditions for their successful application. This paper reports the results of the laboratory study and suggests calculative approaches to estimate the field behavior of the steam-injection process. EXPERIMENTAL METHOD EQUIPMENT A schematic diagram of the equipment used for the displacement tests is shown in Fig. 1. Essentially, it consisted of a core with suitable means for recording temperatures, a feed system for injecting steam or cold or hot water, and a receiving train for condensing, cooling and measuring produced fluids. For the steam experiments, air-free saturated steam was piped from the boiler to the core face in insulated lines that were provided with steam traps and bleeds to remove any condensate formed in the lines due to heat losses. A 12-in. section of the line immediately ahead of

By A. F. Bertuzzi, M. R. Tek, F. H. Poettmann

A method is presented for predicting pressure drop for two-phase fluid flow in horizontal pipes. A set of 267 experimental measurements randomly sampled from approximately 1,000 measurements from various literature sources was used. Pressure gradients calculated by the procedure developed and compared with the experimental values showed a bias of +0.82 per cent and a standard deviation of 20.8 per cent. The advantatges of this method over other available methods of predicting two-phase flow pressure drop are (a) its comparative simplicity of application, (b) its relative independence of flow patterns, (c) its accuracy, which on the basis of a statistical evaluation predicts pressure drop closer than other available methods, and, (d) its ability to satisfactorily correlate laboratory data from various sources while the correlations from these sources do not appear to agree with one another. The method has been reduced to a simplified graphical procedure, suitable for field use. A two-phase f factor is defined and correlated with parameters involving the flowing gas-liquid mass ratio, a Reynolds number for the gas phase, and a Reynolds number for the liquid phase. The choice of parameters allows the correlation to reduce to the usual f factor plot for the limiting conditions of (111 gas or all liquid. INTRODUCTION The mechanics and characteristics of two-phase flow systems have been of interest throughout the industry for some time. In numerous engineering installations such as pipe lines, chemical reactors, and heat exchangers, two-phase flow conditions are of every day occurrence. In oil production operations it has been desirable, in some cases, to consider transporting gas and oil together in a common pipe from oil field to process plant. The trend toward centrally located stock tank batteries in oil fields has resulted in longer gathering pipelines in which more than one fluid phase is flowing. The increase in the producing capacity of oil wells due to new production tech- niques has created the need for review and re-design of many surface gathering lines for properly handling the increased production. Optimum pipe size for the situations described above has become an important factor. The problem which is of interest here involves the ability to predict the relationship between pressure drop, fluid properties, fluid rates, pipe diameter, and pipe length. Although the literature1,5,10,13,18,19 contains various articles dealing with specific cases of the problem, Lock-hart and Martinelli17 proposed the most general solution. Their method has been later modified by Baker:1 Alves2 demonstrated that different flow patterns are possible for a flow mechanism defined by Martinelli such as gas turbulent, liquid turbulent. Baker explained deviations experienced with Martinelli's correlations on the basis that different flow patterns could exist for the same flow mechanism. Using Martinelli's method of correlatioil, Baker correlated data for each flow pattern for the turbulent-turbulent flow mechanism. Bergelin and Gazley6,7 presented a correlation for predicting gas phase

Jan 1, 1957

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949