Search Documents

By C. F. Clausen

"Cement" means binding agent or glue. It is derived from the Latin word "Caementum," the name of a limestone, chips of which were used in mortar more than 2,000 years ago in Italy. During the middle ages "cement" or "cement" generally denoted mortar. Today it means any binding material. The Thomas Register lists nearly 200 classifications for "cement" including automobile cement, household cement, rubber cement, etc. The material most commonly associated with this word, however, is portland cement which, when mixed with water and allowed to hydrate, is a ceramic binding material used to cement aggregates (crushed stone, gravel and sand) together in "concrete," the most universally used building material of today. It is estimated that more tons of concrete are used annually than all other building materials put together including steel, lumber, gypsum, bricks, tiles, aluminum and glass. Its use in foundations, building construction, sanitary work, dams, railroads, and highways, makes it difficult to conceive of modem civilization without concrete. A survey made in October 1955 showed the following uses of portland cement: [Percent Highways20 Nonresidential buildings20 Residential buildings15 Military construction10 Sewer and water works8 Public utilities10 Other (conservation, farm, and maintenance and repair)17 100] As of today, the percentage for highways is probably even higher. Ceramic binding materials have unquestionably been used in construction work for thousands of years. The mortar between the blocks of the great pyramids was calcined gypsum (plaster of paris). The use of calcined and slaked limestone goes back earlier than the Roman Empire. Gypsum, however, is relatively soft, and common lime mortar is not "hydraulic," i.e., it does not harden under water. The Greeks and Romans discovered later that an addition of a finely divided active siliceous material (Santorin earth or Pozzolana) would react with slaked lime to form a stronger, and hydraulic, cement. The Appian Way in Italy, Colosseum, and the great Aqueducts built by the Romans were made with this type cement, and some of these structures are still in existence today. However, not until 1756 did some serious research result in the development of better cements. In that year the English engineer, John Smeaton produced a stronger cement by burning a limestone containing considerable proportions of clayey impurities. Other investigations and improvements were made by Bryan Higgins, Bergmann, Joseph Parker, L. J. Vicat, J. F. John, James Frost, and I. C. Johnson.2 Traditionally, but perhaps unfairly to others, the invention of the prototype of today's portland cement is credited to the English mason Joseph Aspdin who in 1824 obtained a patent and gave the product its name, because in color the mortar produced from it resembled a natural building stone obtained from the British Isle of Portland. The contributions of Johnson and Aspdin were primarily the important step of preparing a synthetic mixture of lime and clay without depending on raw materials found in nature which might contain such elements in desirable proportions. However, even these early

Jan 1, 1960

By L. A. Wilson, N. H. Harrison, R. R. Clay, R. L. Reed. D. W. Reed

Experiments have been performed in a linear near-adiabatic system for the purpose of extending data on reverse and forward combustion from atmospheric pressure to 1,000 psig. Results obtained from reverse combustion appear to conform qualitatively with the existing description of the process when reaction kinetics are suitably modified to account for the increase in pressure, i.e., increasing tbe pressure decreases the peak temperature and increases the combustion zone velocity. Forward combustion appears to be a fuel dominated process wherein peak temperature and combustion zone velocity are not very sensitive to changes in pressure. The moderate effects of pressure that do exist at low flux virtually disappear at high flux providing all oxygen is consumed. With this provision. increasing the pressure decreases the frontal velocity and increases the peak temperature. Results me shown graphicaIIy which demonstrate the effects of presswe on peak temperature, rate of advance, oil recovery, air/oil ratio, carbon oxides produced and temperature distributions. INTRODUCTION Numerous field tests of oil recovery using the technique of underground combustion are now in progress. Operating pressures used are always substantially in excess of atmospheric pressure. Nevertheless, the literature contains no laboratory data pertaining to the effects of pressure except for those of Martin, Alexander and Dew.1 Unfortunately, these data appear to reflect heat losses which may have obscured some of the effects of increased pressure. The underground combustion processes are exceedingly complex, and general concepts relating to them have necessarily been described in relatively simple terms. Particularly with regard to forward combustion, the interaction between multiphase fluid flow, heat transport and various rate mechanisms is so involved that to date a rigorous treatment is not available. In this paper a linear near-adiabatic system is described which was found capable of operating at pressures up to 1,000 psig and temperatures of at least 1,100 F. Using this equipment, experiments on both forward and reverse combustion were accomplished at elevated pressures and the data presented as a function of air flux or temperature. It will be assumed that the reader is familiar with the papers of Wilson, Wygal, Reed, Gergins and Henderson on forward combustion and that of Reed, Reed and Tracht3 on reverse combustion, so that it is not necessary to repeat the details of the two processes. EQUIPMENT AND PROCEDURE It was decided to study the effects of pressure over the interval 0-1,000 psig using a near-adiabatic system. Since satisfactory operation of such a system requires very thin tubing walls, it proved necessary to insert the entire combustion tube and heater assembly into a high pressure jacket in such a way that the internal tube pressure could be counterbalanced by pressurizing the annulus. This meant that the numerous heater and thermocouple wires had to pass through gas-tight seals that required considerable effort to maintain effective. An unexpected difficulty arose in connection with the nature of the annulus pressuring gas. It turned out that the composition of this gas critically affected the functioning of the adiabatic control system. Operation of the equipment at elevated pressures was not particularly difficult. The problems that did arise were a direct consequence of the large numbers of connections and seals involved. EQUIPMENT The equipment consisted of the combustion tube which fitted within the pressure jacket. This jacket was in turn mounted on a wheeled carriage which facilitated movement and provided for rotation of the

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By Donald F. Kennedy

During the past several years Climax Molybdenum Co. has been engaged in testing various types and sizes of hollow drill steel. The majority of tests have been on 7/8-in. hexagon st.ee1, inasmuch as it represents approximately 70% of total drill steel consumption at the Climax operation. Prior to December 1960, tests on 7/8-in. hexagon drill steel were conducted on steel with a forged collar and, in most cases, with a threaded bit connection. Through these tests and research, some improvement in steel life was achieved by making changes in heat treatment, design and alloying constituents. However, during that month, research and testing commenced on a rubber collar which was designed to replace the forged collar on 7/8-in. hexagon drill steel. Manufactured by the LeRoi Div. of Westinghouse Air Brake Co.. the collar. is very simple in design, consisting of a 1 ½ -in. diam steel cylindrical sleeve 2 in. long, containing a bonded rubber insert and attached to the steel with an epoxy cement

Jan 8, 1962

By B. I. Routh

A STUDY of the effects of temperature on the gel strength of drilling muds is a natural outgrowth of the present era of deep drilling. The control of the gel solids' is now considered important because it affects the wall-building qualities; the suspension of weighting material; the removal and release of sand, cuttings, and gas; and the control of cav-ing formations. With regard to the effect of temperature on gel strengths Herrick2 states: "Temperature variation within ordinary limits does not have much effect on yield points." Lewis, Squires and Thompson3 investi-gated one clay and found no marked change with temperature in either yield point or mobility. Reed4 found that potassium bentonite showed a great increase of gelation with increase in temperature and qualitatively there occurred a marked increase in viscosity upon heating. The apparatus used in these experiments consisted of a Stormer viscosimeter, Marsh funnel viscosimeter, rectangular and cylindrical shearometers, Mudwate hydrometer, and other minor laboratory equip-ment. The various methods of measuring viscosity and gel strength have been extensively described by Evans and Reid.5

Jan 1, 1938

By V. J. Decarlo, J. J. Gilman

POLISHING pure zinc differs somewhat from polishing less reactive metals. The problem is not that of finding a suitable reagent, but rather of producing the polish in such a way that the surface remains polished after it is removed from the polishing bath. In other words., the anodic film that is vital to the polishing mechanism' must be tightly adherent and nonporous. It is usually desirable that it be thin. Polishing solutions consist of proper proportions of an acid and a strong oxidizing agent. In electro-polishing, the external circuit acts as the oxidizing agent. The proportions are critical because the essential surface film must be maintained at approximately constant thickness during the polishing process. In the case of zinc, chiefly two oxidizing agents, chromic and nitric acids, have been used. The simplest polishing reagent is concentrated nitric acid. However, it has certain disadvantages. It tends to pit: an excessive amount of heat is evolved during polishing; and the oxide film that it produces is not very stable, so that the polished sur-

Jan 1, 1957

By Howard A. Meyerhoff

IN western Argentina, in the Province of Mendoza and the Territory of Neuquén, there is a series of solid bitumen deposits which are claimed to be the most extensive in the world. In a linear belt 500 km (311 miles) long, roughly paralleling the axis of the Andes but occupying a variety of positions with respect to the orogenic structures, more than 100 outcrops have been reported. Approximately 70 of these have been prospected, and some mining has been planned or attempted for about half this number. Limited tonnage, high sulphur content, inaccessibility, labor shortages, and disastrous fires have taken a heavy toll among these operations, and in 1947, only 4 deposits were being actively mined, but 8 more were being explored and developed with a view to placing them in production. Inasmuch as these deposits are currently yielding a substantial fraction of Argentina's limited domestic supply of solid fuels, a brief account of the deposits and of the small industry based upon them will provide a commentary on Argentina's fuel problem. CHARACTER OF SOLID BITUMENS The solid bitumens of Mendoza and Neuquén are petroleum derivatives, as is indicated by the following ultimate analysis: [CONSTITUENTS PER CENT Hydrogen6.8 Carbon82.4 Nit.rogenI.6 Oxygen2.7 Sulphur2.2 Ash4.3 100.0] In physical appearance they bear a close resemblance to coal and are commonly called carbón. Their specific gravity has an extreme range of 1.10 to 1.777 in 36 samples weighed, but the average is between 1.14 and 1.24. The material is black, lustrous to dull, with blocky to sub-conchoidal fracture. Though brittle, the purest material is softer than anthracite and exhibits slightly more cohesion. This bituminous material is generally known as asfaltita or asphaltite, but definitive chemical studies indicate that the term asphaltite or grahamite can be applied correctly only to the exceptionally pure material of the Auca Mahuida district in Neuquén. Some other name should be used for the chemically variable bitumens found in all other districts, and the designation "asphaltitic pyrobitumen" has been proposed by Carlos A. S. Piscione.1 At the present time these bitumens, are finding favor as solid fuel and as a gas-producing medium. They yield heat values of 8650 to 9750 cal,2 or 14,500 to 16,750 Btu per pound, and in consequence of their excellent heating qualities and the scarcity of imported coal, they are marketed as far away as Buenos Aires at a price of go to 95 pesos, or approximately $22 to 23, per metric ton. In burning, the material swells and decomposes into solid, fluid, and gaseous fractions which burn violently though nonexplosively. Its combustibility has been responsible for disasters and virtually complete destruction at Mina La Esperanza and Mina Santa Marta, and for minor mishaps elsewhere, as at Mina Escondida in August 1947.

Jan 1, 1947

By V. C. Allen

THE Tri-State Zinc, Inc., Galena, Ill., was confronted with the problem of securing ore from a deposit because the hoisting shaft was several thousand feet from the mill. The orebody is several thousand feet long, averaging 200 ft in width and 60 ft in height and opened up by vertical shafts some 300 ft deep. Mining is by the room-and-pillar method. During the initial operation the ore was loaded by conventional electric 1/2-yd boom-and-dipper shovels and hauled to the shaft by 8-ton diesel trucks. This underground ore loading and hauling was well adapted to the conditions and productive of low costs per ton. However, with the mill situated as mentioned, a triple handling of all broken rock was necessary: l—from the stope to the shaft by truck, 2—up the shaft by skip br can into the surface hopper, and 3—by truck from the surface hopper to the crushing plant at the mill. In addition to the repeated handling, serious troubles were encountered during the winter because of freezing in the shaft hopper. Consideration was given to either moving the mill to the new orebody or to the construction of a second mill. The presence of other orebodies to be mined at a later date made the first alternative impractical while the capital outlay for a second mill, when the present plant of approximately 850 tons per day was deemed sufficiently large for the total reserves, made the second alternative also unwise. It was decided to retain the mill in the originals location and continue to move the ore to it. The idea of driving an inclined adit from the surface to the bottom of the orebody suitable for truck haulage and big enough to allow the passage of all mechanical equipment was conceived. Among the apparent advantages of such an incline were: 1— Direct haulage from the stope to the mill without rehandling. 2—Elimination of virtually all grizzlies. Trucking from underground to the mill would do away with all hoppers, chutes, gates, and skips and make the maximum rock size dependent solely on the size of the shovel dipper at the mine and the crusher opening at the mill. 3—Less secondary blasting would be needed. 4—Ease of transporting equipment and supplies underground. Shovels and trucks could be taken through the incline intact. 5—Equipment could be brought to the surface for repairs and servicing without loss of time. The same advantages of ease in moving would be present in the handling of men, steel, powder, and supplies. 6—There would be far less difficulty in increasing the amount of tonnage that could be moved by truck up an incline than would be found in attempting to increase the capacity of a shaft. 7—All the broken ore in the stopes would serve as bin capacity, as it would take the breakdown of all of the loading and hauling equipment to have the same effect as a delay in shaft hoisting. 8—All danger of men being trapped in the mine as a result of shaft fire or power stoppage would be eliminated. 9— Virtually all trouble from severe winter conditions would be eliminated by the direct haul underground to the mill. The decision was made to proceed with the driving of an inclined adit. The topography of the surface between the orebody and the mill was such that it was possible to locate the portal at a point 170 ft above the mine floor and 1800 ft horizontally from the central point of the orebody to the south and 2500 ft from the mill to the north. A grade of 10 pct was found to be optimum for continuous truck haulage when the various factors of speed, safety, and truck maintenance were all considered. The incline as driven was consequently 1700 ft long on 10 pct grade and 12 ft high by 17 ft wide in cross section. The tunnel-driving equipment was chosen so that it could be used in mining after the completion of the tunnel. Drilling was done with a jumbo with two Joy jibs mounting 3-in. drills, loading with an Allis-Chalmers diesel-powered, front-end loader of approximately 11/4-yd capacity, and hauling by Koehring Dumptor trucks of 8-ton capacity, diesel-powered. The width of the tunnel allowed the end loader and Dumptor to be placed abreast. Since the Dumptors can be driven either forward or backward with equal facility, loading was accomplished without turning around either machine throughout the loading operation. The crew in addition to the tunnel foreman was comprised of three men per shift at the start and in the later work, four men. Each crew could perform any part of the working cycle. If the drilling was completed and the round blasted in the middle of a shift, the same men would proceed with the loading and hauling. Since the mine already had been drained to the bottom levels, no water was encountered. At the halfway point the tunnel was widened for approximately 100 ft to permit trucks to pass. The total cost of the tunnel excluding the capital outlay for equipment, which was all continued in use in the subsequent mine operation, was $60,363.00 or $35.50 per ft. The tunnel was completed at the end of June, 1949 and has been in continuous use since that time. In the five months from July to November inclusive, 106,049 tons have been transported to the mill or an average of 835 tons per day. No unforeseen disadvantages have been encountered and the advantages which had been predicated before the adit's construction have been more than realized. As previously mentioned, the deposit is worked by the room-and-pillar system with occasional faces up to 125 ft high. Except in driving development drifts when diesel-powered, front-end loaders such as were used in the tunnel are employed, all shoveling is done by Yz-yd boom-dipper type shovels electrically driven. These units need a width of 25 ft and a height of 14 ft in which to operate. All hauling is by diesel trucks, mainly Koehring Dump-tors. Roads are maintained with caterpillar tractors and a road grader. The tonnage output from the

Jan 1, 1952

By O. H. Eschholz

THE electrostatic process of fume precipitation is an excellent example of the successful application of scientific knowledge to an industrial operation. Originally proposed for the precipitation of sulphuric acid mists, it has been extended until at present there is practically no fume carrying gas to which the method cannot be applied. Among the more common applications are: the recovery of non-ferrous smelter flue-dust, iron blast-furnace dust, cement dust, and potash fume. It should be borne in mind that the process is restricted to the precipitation of suspended particles, either liquid or solid, and does not separate gaseous constituents. However, -by proper temperature control, mixtures of vapors having different temperatures of condensation to either solids or liquids may he selectively precipitated. The process consists essentially of subjecting suspended particles, including those too minute to be effectively acted upon by centrifugal or gravitational forces, to such an electrical force that they are driven from the gas stream, acting as a conveyer, and deposited upon a suitable receiving surface. This directional impulse is obtained front the interaction of charged particles and an electrostatic field of definite intensity gradient existing between two dissimilar electrodes, known as discharge and receiving electrodes. In principle, the equipment is equally simple. As shown diagrammatically in Fig. 1, it consists of: (1) A source of high-potential direct current, requiring: (a.) Source of alternating-current energy. (b) Means of transforming from tow voltage to high voltage. (c) Means of converting alternating to direct current. (2) Precipitation chamber having: (a) Transmission tubes for fume-laden gases. (b) Suitably designed and disposed electrodes. (c) Means for affecting removal of deposited solids.

Jan 8, 1918

By V. H. Wilhelm

The outstanding event in the California petroleum industry during 1931 was the continuance of curtailment of crude oil production, which directly reduced drilling and well repair activities. Although all objectives were not attained, a very close balance between supply and demand was maintained during the period of maximum requirements, but the decline in intercoastal and export shipments caused an overproduction during the last half of the year, which indicated that California production would necessarily suffer further curtailment after the end of the year. A new peak in potential crude oil production of 1,187,600 bbl. per day was reported in August and at the close of the year the California potential was 1,069,000 bbl. per day, the shut-in light oil amounting to practically 425,000 bbl. per day and the shut-in heavy oil amounting to about 150,000 bbl. per day. Fig. 1 depicts these conditions and also shows the production and curtailment situation since the inception of proration in California. The December, 1931, potential figure of 1,069,-000 bbl. per day was arrived at after the most careful deliberation by a number of committees, selected to check the potential of practically every well in the state. Continued overproduction in the first three months of 1931 and the inadvisability of building more storage, together with the inability to obtain the proper amount of curtailment in town-lot fields, such as Long Beach, Santa Fe Springs and Playa del Rey, prompted the major oil companies to inaugurate a price reduction in crude oil. This cut caused prices to reach the lowest levels since 1915, and instigated the formation of an oil sales agency, composed of independent operators, which is known as the Oil Producers Sales Agency. The purpose of this organization is to procure a market for its members at reasonable prices, advise them of market conditions and aid them in controlling the amount of oil available for sale. Marketing of oil produced by members began on June 1 and independents controlling" about 160,000 bbl. per day of production had become members by the end of the month.

Jan 1, 1932

By VILLIAN BRADEN

THIS paper is presented in the hope that it will be instructive in view of the future large expansion of the mining industry in the west-coast countries of South America. There is a more or less general impression that the Spanish-American workman is inferior to the American, but after some years of experience and observation I doubt the correctness of this view. Taking into consideration all the elements which make for efficiency of labor, it has been found, particularly in Chile, that under proper organization native labor yields as much, man for man, and more, dollar for dollar, than in the Western United States. If a manager is willing to accept unreservedly the c costumbres del pais, without combating intelligently and patiently the ones tending to inefficiency, he should expect no better results than he deserves. He must conscientiously insist that a " square deal " be given and exacted; that liquor be excluded from camp as far as possible; that comfortable quarters and other uplifting elements of life be provided; and that the costumbres del pais shall not be over-ridden roughshod. He should also insist upon the gradual and reasonable adjustment of these conditions to the exigencies of the work; and (by no means the least difficult of his tasks) he should select the most competent men to patiently direct and teach the natives in the several departments, and by their own example encourage self-respect and decency. While the Braden mine is by no means as yet operated on a large scale, according to modern rating, it will nevertheless be interesting to note what has actually been accomplished there. An illustrative description of the mines and mill of the\

Oct 1, 1909

By E. H. Crabtree

IN an ideal mill, with perfect milling operations, the mineral extraction would be 100 per cent, the, concentrate would be 100 per cent mineral, the tailing would assay zer.0 mineral and the milling cost would be zero dollars. Such an operation can, of course, never be attained. We can only strive to approach it as nearly as possible and in doing so most recognize .the fact that the three primary factors in milling: assay of concentrate, assay of tailing, and cost of operation bear a definite economic relationship to each other. This relation will change from time to time and will be different for different mills, depending on milling equipment, character and quality of feed, market conditions, and other factors. It is granted that for a given operation there is an economic point, but the location of this point is difficult. It is for the purpose of making some of these economic points a little more tangible that this paper has been prepared.

Jan 1, 1930

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By D. L. Albright, R. W. Kraft

Solidification experiments were conducted with the objective of testing the theory of eutectic colony formation. Appropriate control of variables in tests on a series of high-purity aluminum-copper specimens of eutectic composition resulted in the observation of three types of eutectic microstructures, these being a unique structure consisting of lamellae essentially parallel to one another, a banded structure, and the colony structure. Lamellar faults, which are morphologically similar in many respects to edge dislocation models in crystals, produced a complex substructure in these specimens. SOLUTE rejection at the advancing solid-liquid interface of a unidirectionally solidified single-phase metal can cause the liquid immediately in front of the interface to become constitutionally super-cooled below the equilibrium liquidus temperature. Constitutional super-cooling occurs if the solidification rate, R, is too rapid, or if the thermal gradient in the liquid at the interface, G, is too low. 1 This constitutionally supercooled layer in turn stabilizes a cellular rather than a planar interface.&apos; A similar cellular interface has been observed when lamellar and other types of eutectics were unidirectionally solidified, and it has been shown that the cellular interface led to the formation of eutectic colonies.&apos; The lamellar structure is fan-shaped at the edges of colonies (which correspond to valleys or grooves in the cellular interface) because the lamellae grow normal to the local interface. One of the possible mechanisms which might cause the formation of the cellular interface, in the case of solidifying eutectic alloys, is constitutional supercooling of the liquid with respect to a third component rejected by both phases of the eutectic.3,4 On the basis of the analogy between the solidification of single-phase metals and binary eutectics, a eutectic alloy should solidify with a planar interface if the ratio of G/R is sufficiently high to compensate for any impurity which might be present and causing constitutional supercooling. The fan-like microstruc-ture of eutectic colonies should not occur under these conditions and the lamellae should be parallel to one another and to the solidification direction for extended distances. The experiments conducted in this investigation were designed to test these ideas. Following a resume of the experimental procedure, the various microstructures observed during the study are described, and their relationship to the growth conditions which produced them is discussed. EXPERIMENTAL PROCEDURE The eutectic between an aluminum solid solution and 0 phase (approximate composition CuA12) was chosen for this work for the following reasons: it was known that a lamellar structure forms, the eutectic temperature is low enough to facilitate experimental work, and the components can be procured commercially in a very pure form. High-purity copper (est. 99.999 pct Cu, obtained from National Research Corp.) and spectrographic aluminum rods, having impurities other than copper estimated to be Zn-15 ppm, Mg-10 ppm, Fe-3 ppm, Na-2 ppm, Cd-1 ppm, and Mn < 1 ppm, were melted in a stabilized zirconia crucible in a vacuum induction furnace at a pressure of 10 pof Hg. The melt was superheated to about 1000°C to assure mixing, cooled to 780°C and cast into an investment mold which yielded sixteen cylindrical specimen blanks 1/2 in. in diam and 5 1/2 in. long. The casting was allowed to solidify under vacuum. This master heat had an analysis of 32.6 wt pct Cu and 67.4 wt pct A1 by difference. The cylindrical specimen blanks were remelted and solidified unidirectionally in an apparatus illustrated schematically in Fig. 1. An RF induction coil heated

Jan 1, 1962

Boiler-Room Economy "Establishing and Maintaining Boiler-room Economy" is the title of a paper presented before the Ohio Society of Mechanical Electrical and Steam Engineers by Geo. H. Gibson, of which the following is an excerpt: Boiler-room economy depends less upon equipment than upon operation, i.e., it depends largely upon the condition in which the apparatus is maintained and how it is used. A given boiler may operate this week with an efficiency of 78 per cent., and next week with an efficiency of 65 per cent., while using the same fuel and developing the same rating. If there are variations ii; character of fuel and in load and other factors, the falling-off may be even greater, possibly to less than 60 per cent. The steam produced may cost twice as much per 1,000 lb. at one time as at another. Most steam plant managers know from their own experience that these statements are not exaggerated. It does not take much of a plant to run up a coal bill of $5,000 per year, many "spend $10,000 for coal, and fuel bills of $50,000, $100,000, or $200,000 per annum are not uncommon. As it call be shown in the majority of these plants that 10 per cent. of this amount may be saved, and in large numbers of them 25 per cent., while in some the expenditure can be cut in half, there is no disputing that we have here a subject worthy of attention. In the production of steam the greatest variable is the human factor. Before we can pass judgment, however, we must first have standards. This implies accurate quantitative knowledge of fuel consumption and steam production. We must measure the output and know how much the steam costs per thousand pounds, and how many pounds of steam are obtained from a pound of coal. We can then begin to analyze the problem, and find where and how methods and conditions can be improved, and how much. Many favor buying coal on a B. t. u. basis. This is advisable where the amount purchased warrants the considerable expense involved in systematically gathering samples that: are. truly representative and in having analyses made, of every carload. Coal analyses, combined with. an honest endeavor on the part of the miner to ship good coal, should insure the receipt of the heat units paid for. , It often happens, however, that the coal which is cheapest on a B.t.u. basis is not the cheapest or most suitable for producing steam, because of peculiarities of the plant in which it is to be burned, or conversely, the fuel which furnishes cheap B.t.u. may require special methods or equipment for its economic utilization.

Jan 2, 1916

By F. A. Emmerton

I have used for about two years, in the laboratory of the Joliet Steel Company, a rapid method for the determination of phosphorus in iron, steel, and ores, which possesses one or two features sufficiently novel to warrant description. In general, it is the method described by Mr. Benjamin B. Wright (Transactions, vol. x., p. 197), involving the precipitation of the phosphorus by means of molybdate solution, and its estimation in the yellow precipitate by reduction of the molybdic acid, and titration of the resulting oxide with a standardized permanganate solution, according to the principles laid down by Werncke (Fres, Zeit., vol. xiv., p. 1). In the use of this method, I had difficulty at first in obtaining a yellow precipitate of reasonably uniform composition. It is a well-known fact that, to secure this result, the conditions of precipitation must not vary. The principal condition is temperature; and acidity, concentration, proportion of nitrates and chlorides, and time, are important elements. I am aware that uniformity in these conditions has been obtained to a reasonable extent by many chemists,. so that they are enabled to use with success, methods based on the

Jan 1, 1887

By Chi-Yuen Wang, Chaw-Long Chu

The time-dependent volumetric constitutive relation for a San Andreas fault gouge and a consolidated kaolinite are experimentally determined at confining pressures to 200 Mpa, under creep condition and at ultrasonic frequency. At any given pressure, the bulk modulus determined at 1 Mhz frequency is identical to the "elastic" modulus determined at a stepwise change of pressure. After the pressure change, there occur a time-dependent change of volume and thus the effective bulk modulus. The constitutive relations may be modeled by a standard linear viscoelastic medium with pressure-dependent moduli and viscosity. For the San Andreas fault gouge, viscosity increases from 2x10 13 poise, at 17 Mpa, and 10 14 poise, at 100 Mpa. For kaolinite sample, the corresponding values are 3x10 12 poise and 10 13 poise. These results imply that both stress and pore pressure in fault zones may show time-dependent variations in response to a change of state of stress, such as that occurring after an earthquake.

Jan 1, 1982

By John Chipman

DESPITE the rapidity of chemical reactions at steelmaking temperatures, deoxidation reactions cannot be expected to reach equilibrium immediately after addition of a deoxidizing agent. A considerable period of time may be required merely to obtain complete mixing of the deoxidizing element throughout the volume of steel to which it is added. Evidence in the literature indicates that in some cases the time is long compared with that allowed for completion of the experiment or for teeming of the heat. The great turbulence observed during the filling of the ladle is no guarantee of complete dispersion on a fine scale throughout the heat. During the process there are initially certain volume elements which are high in deoxidizer and others which retain substantially their original oxygen content. Mixing consists of the subdivision and ultimate destruction of these liquid segregates through the process of shear and elimination of concentration gradients by diffusion. The shear process does not continue indefinitely and a quiescent state may be reached in the ladle before all volume elements of divergent deoxidizer and oxygen content are completely eliminated. In furnace deoxidation the time required for complete mixing may be very long unless continuous stirring is employed.&apos; In Fig. 1, let the circle represent one small volume element of aluminum-rich metal surrounded by oxygen-rich steel in which no stirring movement remains. Further mixing requires inward diffusion of oxygen and outward diffusion of aluminum, resulting in precipitation of A12O3 in the diffusion zone. It is important to note that such a precipitate may itself interfere with the diffusion process. Moreover, if the precipitate forms as a film with even minimal mechanical strength, it may interfere not only with diffusion but with shear as well, thus stabilizing compositional differences in volume elements of greater than microscopic size. A film surrounding such a volume element would have little or no ability to rise or to sink unless it enclosed a liquid whose density differed from that of the ambient. Consider now the effect on the overall composition of the melt. Fig. 2 represents the A1-O equilibrium at the temperature of the bath. High-aluminum elements of composition X may exist alongside high-oxygen elements of composition Y in such proportions that the average composition 2 has a much higher A1-O product than that corresponding to equilibrium. The A1-O product supposedly corresponding to equilibrium at 1600 °C was found by Wentrup and Hieber2 to be 10-10, by Hilty and crafts3 to be 2 X 10-9 and by Gokcen and chipman4 to be 2 x 10-14. Only the last named investigators approached equilibrium by means

Jan 1, 1962

By Charles S. Barrett, Robert F. Mehl

It is generally understood by workers in the field of the crystal structure of metallic alloys that terminal solid solutions are of two types, the substitutional and the interstitial. In reviewing the literature, the work of Weissl on the crystal structure of the alpha copper-tin alloys was encountered, in which a new type of terminal solid solution was proposed. In brief, Weiss&apos; findings showed that the density of the alloys calculated from the side of the unit face-centered cube on the assumption of simple substitution—that is, with four atoms to the unit face-centered cell—was much higher than the density measured directly. It was suggested that the assumption of four atoms to the unit cube is not valid for these alloys, and that each unit cube contained less than four atoms; in other words, that one tin atom replaces more than one copper atom, leaving some atomic positions unoccupied. Such a structure, if verified, would have far-reaching significance in the study of the crystal structure of metallic alloys. It would indicate a complexity in terminal solid solutions not hitherto suspected and might encourage work leading to the discovery of other alloys of the same type, and perhaps to types intermediate between it and the two recognized types. It is of importance, therefore, to reinvestigate these alloys with respect to the type of solid-solution structure obtaining therein. Materials and Experimental Method The alloys were prepared from electrolytic copper cut directly from the cathode and the high-purity tin furnished by the U. S. Bureau of Standards for the calibration of thermocouples. No analyses for impurities of these materials or of the finished alloys were made, since such impurities as might be present could have only a wholly inappreciable effect upon the data obtained and the conclusions drawn. The alloys were made by melting the weighed copper charge in a graphite crucible under a KCl-LiC1 flux with later additions of NaC1, using induction heating. When the copper was melted the weighed portions of tin were

Jan 1, 1930

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white&apos; studied effects of heat treating on nickel-base alloys and Ewing and reeman&apos; investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959