Search Documents

By W. N. Tanner

THE wire-rope hoisting conditions at the mines of the Anaconda Copper Mining Co. in Butte, Mont., are very severe because of the conditions under which it is necessary to operate. A study was made, in the fall of 1919, for the purpose of changing these conditions in order to obtain longer rope and sheave life. There are at present in Butte, hoisting engines equipped with wire rope as follows: 9 main hoists using flat ropes. 7 main hoists using 1 ½ in. rope. 5 main hoists using 1 ¼ in. rope. 6 shafts using 1 1/8 in. rope. 2 chippy hoists using 1 ¼ in. rope. 9 chippy hoists using 1 1/8 in. rope. 15 shafts using 1 in. rope. 7 shafts using 7/8 in. rope. 1 shaft using ¾ in. rope. In addition, there are a number of sinking engines using 5/8 in., ¾ in., 7/8 in., and 1 in. (15.9, 19, 22, and 25 mm. rope.) The flat ropes run from ½ by 7 ½ in. (12.7 by 190.5 mm.) to ½ by 4 ½ in. (9.5 by 114 mm.) and are used on the older hoisting-engines, which are set comparatively close to the shaft. Because of swelling and moving ground at some of the shafts, these ropes present certain difficulties in operation that are more pronounced than with round ropes; they are, therefore, being superseded by round ropes as newer engines are being installed. They are, however, much more easily inspected and repaired than round ropes.

Jan 2, 1922

By W. W. Cotter, W. R. Clark

WEBSTER tells us the word "extrude" means to "force, press or push out; to protrude." As applied to the metal industry, the process consists largely of forcing plastic elements (plasticity usually obtained by preheating), through dies of predetermined profiles, into constant sections of considerable length and weight. Most of the "virgin" metals are quite malleable under this process, likewise many of the commonly used "alloys" in various industries, when basic elements are proportioned or combined within the natural laws and limits of good metallurgy. Several of the foundry alloys, both ferrous and nonferrous, together with some of the heat-treatable light metal mixtures, are decidedly weak and hot short at ordinarily plastic ranges, and consequently are troublesome or quite incapable of commercial extrusion. DEVELOPMENT OF PROCESS This process was conceived some time before 1800 and during its first century was employed almost entirely in making lead pipe, plumbing fittings and coating electrical cables. As a result of contact and experience with the lead industry and presses, Alexander Dick, of London, England, is credited with first having applied the principles of extrusion to brass, and in 1894 brought out a 500-ton horizontal press powered by hydraulics. A duplicate of this unit was imported by one of the Connecticut brass mills and was in experimental operation by 1900. During the first five years of operation, this press proved the value of the method to American industry, as it immediately revolutionized and converted the manufacture of brass rod from a 15-pass cold-rolling operation, with elimination of several intermediate anneals and cleanings, to an extrusion and a finishing draw. Likewise, ornamental brass and bronze moldings formerly cast and machined were produced in one squeeze on the extruder. The extrusion operation, being entirely that of compression, deforms the material without tensile stresses and can be used on delicate mixtures under heat, which cannot be hot-worked by straight hot-rolling or roller piercing. Base slabs of clock-brass strip were early in line of development or improvement, as were the brass bronzes (Naval brass, Muntz metal, manganese bronze, and others), popular as engineering materials for bolt stock, as well as structural shapes for marine and other mild conditions of corrosion. By 1910, American engineers undertook to design tube shell extruders, but were unsuccessful. The first World War began before fabricators could procure the more substantial designs of tube extruders produced in Germany; and it was not until the middle twenties that better models of the Universal extruders (double-actioned presses), equipped with hydropneumatic accumulator systems and other modern equipment, were available in the United States.

Jan 1, 1945

By F. O. Garrabrant

POWER is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt line to a bank of three 3333-kva. Transformers 100/13.8 kv. These transformers arc so designed that with the addition of forced cooling their capacity may be increased 33 1/3 per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200- amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. MINE Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three 250-kva, 13,800/440-volt, single-phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp. motor on the No. 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 100-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft. Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. Under normal operation the one pumping 1200 gal. per min. is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started, and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the pumps restart. On failure of any of these, an alarm is sounded in the train dispatcher's office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 370 substation is run to the switching station, in which are four15-kv., 600-amp. direct-current solenoid-operated oil circuit breakers. The current for operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1944

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

THE beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than 90 per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as originally proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accumulated since then, showing the utility

Jan 1, 1945

By A. B. Kinzel, Walter Crafts

A PRevioUs study1 of the relations of impact strength to inclusions showed that the dynamic strength of steel is lowered by the presence of visible counted inclusions, but that other factors comprised in the term "body" have a marked influence. The previous work was carried out on selected steels from a single source, so that the body factor was purposely minimized, but even under these conditions it was found that inclusion counting or the use of the commercial inclusion rating is not satisfactory. The tensile-impact test, however, was indicated as a satisfactory measure of dynamic strength. It was further suggested that the tensile-impact test should be so standardized as to be suitable for use in specifications, and that the hardness factor should be worked out over a sufficient range to admit ready commercial use of the tensile-impact test. In accordance with these suggestions, and in view of the fact that the steels reported in the previous paper were selected and treated so as to have a minimum variation in body, hardness and structure, further work has been performed on a variety of steels which are not limited by these conditions. The word "body" is used here for want of a better term. It is simply a convenient expression which comprises the effect, of the various unknown factors that modify the dynamic strength of the steel. Thus at our present state of knowledge, the writers have chosen to consider hardness, structure and counted inclusion content as factors not comprised in the term "body," and such factors as raw materials, process of melting, fabricating, etc., as comprised in the term "body." Numerous grades of steels made in several ways have been taken from different sources and have been heat-treated to varying hardness by normalizing and by quenching and drawing. The results, therefore, may be considered to be generally applicable to current engineering steels. A certain limitation with respect to the hardness at which steel should be tested still seems necessary. The upper limit of this hardness range has

Jan 1, 1931

By R. P. Agarwala, M. S. Anand

Using residual activity technique, the diffusion of palladium, silver, cadmium, indium, and tin in alunzinum has been studied in the temperature range of 400" to 630°C. The diffusivities (in units of square centimeters per second) have been expressed as: IMPURITY diffusion in aluminum,1-9 silverand lead5 for cases of low solid solubility of the impurity in the host metal has yielded frequency factors in the range of l0-6 to l0-9 sq cm per sec whereas the activation energy is practically half the self-diffusion activation energy value. From the observed values of frequency factor, activation energy, and entropy of activation, it has been suggested' that these solutes are not diffusing by vacancy or interstitial mechanisms but by a mechanism which should be consistent with such low values of the diffusion parameters (Do and Q). However in spite of extensive work on these types of systems, the mechanism of diffusion is still not well understood. The present investigation on the diffusion of palladium, silver, cadmium, indium, and tin in aluminum has been carried out to throw further light on the diffusion mechanism in systems, where the solid solubility is very low (except for the case of silver). The results are discussed on the basis of solid solubility and the structural changes involved owing to the presence of the solutes in aluminum solid solution. An attempt has also been made to apply the existing theories of charge5-8 and size8 difference between the solute and the solvent. EXPERIMENTAL PROCEDURE Specimens (1/2 in. diam by 3/8 in. high) were machined out of pure aluminum (99.995 wt pct) rod obtained from Johnson Mattheys. They were sealed under vacuum in quartz tubes and annealed at 620° C for several hours; the grains thus developed were sufficiently large to eliminate the possibility of diffusion along the grain boundaries. The flat ends were prepared carefully after polishing as described previously,10 Radioactive nitrates of cadmium, indium, and tin and chloride of palladium containing, respectively, cd115, 1n114, sn113, and pd103 were dissolved in distilled water and mixed with 30 pct acetone. By means of a micropipet a drop of this solution was placed on a smoothly polished and lightly etched surface of the specimen. Due care was taken to see that the solution spread uniformly on the surface of specimen without trickling down its sides. Radioactive silver was elec-trodeposited using a AgCN-KCN bath. The amount of sample deposited in all the cases was not more than 0.1 µ thick. The samples were then sealed in quartz tubes in vacuum. The cadmium samples were sealed in a purified argon atmosphere to avoid evaporation. The samples were then diffusion-annealed. The temperature of annealing varied between 400° and 630°C and was controlled to ±5°C. On heating to -400°C,the deposits of cadmium, indium, and tin, which were of the order of 0.1 p in thickness, were converted to their respective oxides. The contribution of oxygen present in the lattice of aluminum due to these oxides has been calculated and found to be less than 10 ppm in all cases. Oxide method has already been used by other workers11'12 in diffusion studies without any controversy on the issue. However, in some of these investigations, metallic deposition was also tried. The diffusivities calculated from these measurements were found to agree very well with the diffusivities obtained by using the oxide method. Thus it is assumed that the measured diffusivities represent true diffusion coefficients. Since palladous chloride decomposes at about 500°C, the deposited samples which were to be diffusion-annealed below 500°C were heated in vacuum for a very short time at 500°C to allow the decomposition of palladous chloride to palladium metal. Time taken in decomposition of nitrates to oxides and chloride to metal was negligibly small as compared to the period of the diffusion anneals. The residual activity technique13 was used to study the diffusion profiles where thin layers from the specimen surface were removed by grinding it parallel to a flat surface on a 600-grade carborundum paper. The specimen was washed, dried, and weighed, the differ -ence of the weight being the measure of the thickness of the layer removed. After each such abrasion and weighing, the total residual activity on the surface of the specimens was measured by counting 0.656, 0.94,

Jan 1, 1968

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By J. R. Thoenen, M. C. Malamphy, G. K. Dale

The beginning of the war and the events leading up to it precipitated a near crisis in the aluminum industry. Demands for the metal reached proportions far beyond the prewar production capacities and, in addition, the submarine menace seriously curtailed the importation of bauxite from South America, hitherto a chief source of high-grade ore. The situation required an intensive search for domestic ore to augment the reserves and in October 1941 Congress directed the Department of the Interior to investigate the extent, mode of occurrence, and quality of bauxite in the United States. In December of that year the Bureau of Mines and the Geological Survey began the search for bauxite in Arkansas, where more than go per cent of the domestic ore had been produced and where the greatest amount of bauxite was known to occur. The program involves the geophysical and geological investigation of the Arkansas bauxite region and the core drilling of areas considered favorable for the occurrence of bauxite deposits. Cores taken from the bauxite-kaolin zone are sampled and analyzed in the Bureau of Mines laboratory in Little Rock. The information from each of the deposits discovered is then assembled, the bauxite is graded with respect to its possible utility, tonnage estimates are made, and the whole is presented in the form of a war minerals report. Thirty-eight new bauxite deposits had been discovered and investigated at the end of the calendar year 1944, and the presence of several others had been indicated by the drilling. More than 5000 holes had been drilled throughout the bauxite region, and more than 60,000 chemical analyses had been made of samples taken from the bauxite-kaolin zone. A study of the chemical analyses led to certain general conclusions not only with regard to the chemical composition of Arkansas bauxite, but also with regard to its component minerals. Charts and diagrams based on these conclusions have been developed for practical use by the Bureau of Mines: (I) to serve as a check against laboratory analyses, (2) to present tonnage estimates of ore bodies based on mineral composition, (3) to illustrate the relationship of tonnages of bauxite to the alumina, silica, and iron content, and (4) to serve as a control for mining operations by providing a means for quick estimates of the value of the ore from a partial analysis of its chemical constituents. The use of charts and diagrams similar to those discussed in this paper-- is not new. The use of the trilinear diagram for studying the ultimate analyses of coals as of proposed by Ralston in Bureau of Mines Technical Paper 93 (1915) showed that the various ranks of coal fell in different areas on the diagram and that volatile matter, calorific value and other properties could also be plotted by the use of contours. A considerable subsequent literature, largely on classification of coals, has accurnulated since then, showing the utility

Jan 1, 1948

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By T. P. Clendenin

THE northerly two thirds of Mexico falls into five main physiographic divisions, illustrated on the accompanying map. In form, these divisions are a series of strips, paralleling the northwest-southeast axis of the country.

Jan 10, 1951

By P. R. Sperry, M. L. Holzworth, P. A. Beck

The basic work of Z. Jeffries 1,2,3 has long ago established the main features of grain growth in the presence of a dispersed second phase. Working with sintered specimens of initially fine grained tungsten, to which various amounts of thoria had been added, Jeffries found that grain growth was inhibited, that is, practically prevented, up to a certain annealing temperature. When this temperature, which increased with the thoria content, was exceeded, extremely large grains developed abruptly from the fine grained matrix. such a a temperature" was later found by Gross-mann~3,14 in certain types of steel, while ~~i~ showed15 that in other steels grain growth was gradual, without inhibition and abrupt coarsening. Later work demonstrated the connection between coarsening and aluminum additions. The viewpoint that the direct cause of inhibition and coarsening in aluminum killed steels is a fine dispersion of aluminum oxide21 appears to be held quite generally, although some doubts have been voiced even very recently, 20 In steels with Ti additions the titanium carbide phase is considered responsible for the inhibition effects found.20 The coarsening temperature increases with the titanium content. That coarsening may occur, as a result of, certain heat treatments, even in low carboil rimmed sheet steel, was shown by Samuels. He also detected coarsening in a steel ingot of similar composition, after giving it the same heat treatment as that used by him for the sheet material. In this instance the identity of the inhibiting phase has not been determined. However, Tangerding found23 that even the few small carbide particles, which occur in carbonyl iron, have a very marked inhibitive effect. As a result of an oxidizing anneal at 850°C, large grains begin to form at the surface of the carbonyl iron specimen, and gradually grow inward as the subsurface oxidation of the carbide particles progresses and eliminates the obstruction. The carbide particles Can be removed also by annealing in hydrogen, with similar results. But if the oxidizing anneal of 10 hr at 850°C in air is followed between in hydrogen for 75 hr at the Same temperature, grain growth is more hibition usually the whole specimen is transformed into a single crystal (approx. 1.5 cm X 5 cm). The reversed procedure, that is, hydrogen annealing followed by oxidizing annealing leads to smaller grains. Tangerding arrived at the logical conclusion that there must have been in his specimens some additional obstruction to grain growth hibition from a minor impurity, other than carbon. It seems likely that this obstruction was caused by an oxide formed during the oxidizing anneal and gradually reduced rtain the subsequent hydrogen-annealing. Other instances of grain growth inhibition of varying severity, associated with a dispersed second phase, have been described by several authors. Notable examples: lead with 0.06 pet Cu or Ni,24 cartridge brass with 0.12 pct Cr,25 or with up to 0.15

Jan 1, 1949

JOHN ALEXANDER MATHEWS, who has been awarded the Hunt Gold Medal for his paper "Austenite and Austenitic Steels," which was pre-sented before the Institute as the Howe Memorial Lec-ture for 1925, was born at Washington, Pa., on May 20, 1872. His interest in metallurgy may be said to be hereditary, as three generations of his Colonial forbears were gold and silversmiths. After graduating from Washington and Jefferson College in 1893, he entered Columbia University where he was successively assistant in assaying and tutor in chemistry and at the same time continued his work for the Ph. D. degree, which he received in 1898. He was at one time awarded a fellowship in chemistry, and for 1900, 1901 and 1902 re- ceived the award of the Ear- nard Fellowship for the En- couragement of Scientific Re- search, spending one year at the Royal School of Mines, in London, studying alloys un- der Sir William Roberts- Austen, another at Columbia under Henry M. Howe, and the third at Sanderson Bros. works, Syracuse. While in England, he was one of the first three, recipients of an Andrew Carnegie Scholarship of the Iron and Steel Institute of Great Britain, which later awarded him the first Car- negie Gold Medal for Re-search. He entered the employ of the Crucible Steel Company of America, at its Sanderson works, in 1902, as metal- lurgist and soon became as- sistant manager. In 1908 he ent to the Halcomb Steel JOHN A. Co., Syracuse, N. Y., as superintendent, later becoming general manager and president in 1915. In 1920 he returned to Crucible Steel Co. of America, first as vice-president and later became president from 1921 to 1924. He retired from the presidency in 1924, made a metal-lurgical trip to Europe, and returned as vice-president to resume his "favorite pastime" of directing research and development work in the production of special tool and alloy steels. He has taken a particular interest in the development of austenitic steels which, in addition to an extraordinary resistance to corrosive attack, show under fatigue, torsion, and tension tests superior qualities as compared with the ordinary engineering steels, and at elevated temperatures show remarkable resistance to oxidation and scaling and several times the strength of many of the complex alloys that are not of the natural austenitic variety.

Jan 2, 1928

By Francis Cameron

Gloomy predictions that domestic mineral reserves are approaching exhaustion are unwarranted and may be harmful, this author contends. Specific mineral forecasting errors in the Paley Report are cited to support this contention, and steps that can be taken to insure a progressive mineral industry capable of keeping pace with the major raw material needs of the nation through advancing technology are suggested. Mining is both exciting and rewarding —although at times somewhat frustrating— and we all can have real pride in our industry, in its people, and in its accomplishments. It is, however, with concern that I have noted a deterioration in this Country in what might be called mining's stature and in the growth of a belief in many quarters that our mineral reserves are rapidly approaching exhaustion. In other words, there is a popular image that we are fast becoming a "have not" nation in many respects and that the domestic mining industry can no longer be considered, in the vernacular of Wall Street to offer much in the way of "growth potential." I do not subscribe to this hypothesis, nor do I be-li4ve that the record of the mining industry bears this out. However, let me add that we can, in time, talk ourselves into this frame of mind and we can hasten the day when this very well might come about by unnecessary and unwise legislation or regulation. My remarks today are basically designed to give my reasons for refuting this negative philosophy and to review our record. With your help, I know we can improve our image, and the public's recognition of our industry's peculiar problems. The progress of our civilization over the centuries has been fundamentally based upon proper use of raw materials, both agricultural and mineral, and upon energy, human or otherwise. As the standard of living has progressed century by century, the demands for mineral raw materials have increased in an irregular, but steadily rising progression. Fortunately, those minerals on which we depend most, i.e., iron, coal, petroleum, copper, aluminum, lead, and zinc have been neither too difficult to find nor to process into useful form. Iron, the most useful of all metals, is present in various amounts in most rock types and soils. Gold, seemingly the most generally desired (but certainly not the most useful of all metals), occurs in sea water in a far greater total tonnage than has been won from all of the world's known gold mines. If the latter is true, then why do we not see large installations treating sea water for the recovery of its gold content? The answer, of course, is that even the French, who seem, from their recent actions, to value gold above all else, have not devised a way of doing this at a profit. Theoretically, it is possible, but not with today's technology at a cost which would justify the effort. Man has exploited only those mineral concentrations which accidents of nature have placed within his so far limited means of finding and utilizing. What we geologists and engineers refer to as an orebody is nothing more than a concentration of minerals, exploitable with available knowledge, that will yield a value greater than the value attached to the energy and capital required to produce it. What is "ore" and what is not "ore" is, in the end, a matter of economics. The economic problem stems from the physical and chemical character of mineral deposits. The good Lord stacked the cards heavily in favor of rising costs by limiting the amount of the higher grade ores easily available. As the best and most accessible ores are depleted, it becomes necessary to work harder and with greater ingenuity to produce more from less accessible and lower grade resources. The quantity of mineral raw materials we can have in the future will be determined largely by what we can afford to pay for them in terms of human effort, capital outlay and production energies. We will always have the problem of cost with us and our only real means of keeping ahead of rising costs is by continually improving our technical abilities. We, in this country at least, no longer have open to us large and unexplored virgin wildernesses in which a pick-and-shovel prospector might uncover an untouched mineral bonanza. The rest of the world also has few conventional frontiers left in which the explorer-prospector is free to roam. We do, however, have enormous land areas unexplored, and untouched po-

Jan 1, 1969

By Edward P. Barrett

DURING the past few years numerous references have been made in the technical press and Bureau of Mines Bulletin 270 to sponge iron' and so-called "direct metal" processes. The idea has been prevalent that sponge iron and "direct metals" are cheap commodities. In many instances it has been proposed that these processes be used to treat low-grade ores, utilizing low-grade coals as reducing agents. It is questionable whether or not high-grade sponge iron can be made from low-grade materials. Particles contain¬ing iron oxide and gangue become, upon almost complete deoxidation, particles containing metallic' iron and gangue. The possibility of mechanically separating the metallic iron from the gangue in these particles depends . on the physical characteristics of the particular ore under treatment. Some ores, in which the minerals constituting the gangue break free from the iron oxide upon crushing, may be concentrated magnetically after the iron oxides have been reduced to metal. The finely disseminated ores are least amenable to concentration. In general, high-grade sponge iron can only be made from high-grade raw materials. Sponge iron containing small amounts of sulfur can only be made from raw materials containing small amounts of sulfur or by

Jan 1, 1930

By James W. Halley

' FINE-GRAINED " steels have been standard products for many years. This paper describes an investigation of the effects of some of the more common grain-growth; inhibitors used to produce these steels. The properties, response to heat-treatment, and the deoxidation practice necessary to produce "fine-grained" steels have been the subjects of numerous papers. It has been shown that a substantial quantity of' aluminum is necessary to produce this type of steel, and it has been indicated that titanium and zirconium produce a similar result. For some time there was a lively argument between those who felt that aluminum refined the grain and those who felt that aluminum oxide was the effective agent. This argument subsided with an apparent victory for those promoting aluminum oxide. Most of the work on grain size has divided steels into two broad classifications based upon McQuaid and Ehn's original carburizing test at 1700°F. or some similar test at this temperature. If the steel coarsened at this temperature, it was coarse grained, while if it did not it was fine grained. Quantitative data concerning how much a certain amount of aluminum raised the coarsening temperature and affected the properties, all other factors being constant, are very meager. Similar information regarding titanium and zirconium is practically nonexistent. The published information on aluminum yields some quantitative information. Epstein, Nead and Washburn' gave the first quantitative information on the amount of aluminum necessary to prevent grain growth at 1700°F. They showed that the addition of a pound to a pound and a half of aluminum per ton (0.05 to 0.075 per cent) would assure steel that would not .coarsen during a McQuaid-Ehn test at 1700°F. Herty, McBride and Hough2 reported that a steel containing 0.020 per cent acid-soluble aluminum coarsened between 1742° and 1832°F., while steels containing 0.016 per cent and 0.017 per cent acid-soluble aluminum coarsened between 1652~ and 1742°F. compared with similar aluminum-free steels that started to coarsen at 1580°F. Herty3 also showed a marked improvement in low-temperature notched impact resistance with increasing acid-soluble aluminum up to 0.030 per cent. McQuaid4 compared the coarsening of steels containing 0.011 to 0.204 per cent total aluminum and found a maximum coarsening temperature at 0.098 per cent aluminum. He had no samples between 0.015 and 0.098 per cent aluminum. Houdrement5 found a marked decrease in coarsening temperature with aluminum contents above 0.50 per cent. Kinzel, Crafts and Egan6 found that aluminum and zirconium improved thy low-temperature impact resistance of a low-alloy steel, while titanium was detrimental. Sims7 shows that sulphur increases the coarsening temperature and that the maximum coarsening temperature is between 0.04and 0.06 Per cent added aluminum. The

Jan 1, 1946

By J. Nutting, D. H. Kirkwood

The oxidation of lead sulfide in air between 200° and 350°C has been investigated by electron diffraction from thick sulfide films and from galena surfnces. It has been demonstrated that sulfate is the stable reaction product up to 570°C. Sulfate is HAGIHARA has investigated' single crystals of galena roasted in air by the reflection electron-diffraction technique, which owing to the very limited penetration of the beam into the crystal gives information of the nature of the surface only. He has shown that up to 280°C the first oxidation product is lead sulfate, followed by lead mono-oxysulfate (PbO . PbS04). At longer times and higher temperatures more complex patterns appeared which could not be analyzed. All of these patterns were of streaks or spots arising from crystals oriented on the galena surface, and it is probable that these crystals are lead compounds whose structures have not been determined, such as the other oxysulfates (2Pb0 • PbS04 and 4Pb0 . PbS04) or a number of oxides. Certain lead sulfide films, formed chemically, give ring patterns in transmission electron diffraction2 because they are polycrystalline, and should also give ring patterns of the products after oxidation. It was thought that a diffraction study would reveal the sequence of phases produced in the reactions at different temperatures, since X-ray powder patterns are available for many lead compounds. PREPARATION OF FILMS The films were prepared by passing H2S over a saturated solution of lead nitrate in water. Once a silvery film had formed on the solution surface, no further thickening was apparent. The films were transferred by a gauze to a bath of distilled water for washing and pieces of film were caught on small discs on which they were dried. The discs were formed initially on galena up to temperatures of 300°C, followed by oxide and oxysulfates in turn at longer times. The appearance of- these phases is believed to result from an inadequate rate of supply of sulfur to the top surface 01. the crystal. standard Siemens mounts, made of platinum alloy, and had seven 20-p apertures drilled through them. The parts of the film which had dried onto the disc surface were light blue in color, which is the interference color of a film about 600A in thickness. A strong pattern of lead sulfide was obtained in transmission electron diffraction through the apertures but slight broadening indicated a crystallite size of around 200A. Tilting a sulfide film in the beam produced arcing of the rings, increasing the intensities of the (Ill), (3111, and (222) rings and reducing (200) and (220). This arises from preferred orientation in the film, a [loo] direction of the crystallites being normal to the plane of the film. These specimens were oxidized in an oven maintained at the required temperature. The reported times include that taken to heat the film to the reaction temperature. STABLE PHASES FORMED IN OXIDATION The conditions in which various oxidation products of lead sulfide are stable have been considered by the authors in a previous paper.3 It was shown that in a normal atmosphere, taken as containing lo-' atm of SOs, lead sulfate would be stable up lo about 570°C. This was confirmed by oxidizing thin films of sulfide for several days, and the analysis of the transmission-diffraction pattern is given in Table 1. The fit with the patt$rn from X-rays is good, except for the missing 3.62A ring. Some disagreement in intensities of reflections given by X-rays and electrons is to be expected. Up to 570°C a spotty pattern of sulfate was still obtained, indicating grain growth, but above this temperature the film disintegrated. Probably this is associated with the decomposition to PbO . PbS04. It needs to be emphasized that the atmosphere

Jan 1, 1965

By F. Twyman

PART I.-QUALITATIVE, SPECTRUM ANALYSIS THOSE chemists (they are still greatly in the minority) who use the spectroscope, use it very often, and find it almost indispensable. As a means of detecting minute quantities of the metals it is unrivalled. A metal can be readily distinguished in the presence of any other element, compound, or mixture without the necessity of separation. The qualitative analysis of the metallic constituents of a substance, which, the spectroscope gives so easily, is a sure basis for planning a chemical analysis. As the determination of each element proceeds the purity of precipitates maybe checked as often as desired. If, possessing these advantages; the spectroscope has been neglected in general chemistry, it is not surprising that it was neglected in metallurgical chemistry; for many of the impurities which are of industrial interest, even when they are present in a metal or alloy in small quantities, are not then always easily detected by the examination of their visible spectrum. The history of the development of the art has been given in Bureau of Standards Scientific Paper No. 444.

Jan 1, 1928

By Nicholas J. Grant, Robert H. Kane, Bill C. Geissen

The platinum-rich section of the Ta-Pt Phase diagram was worked out by metallographic and X-ray techniques, using twenty alloys; solidus temperatures and solid solubilities were determined. Besides s phase, four intermediate stoi-chiometric phases were found: TaPt (high-temperatzrre phase, structure unknown); TaPt2 (ortho-rhomhic, new type); a TaPt3 (orthorhombic, TiCu3 type); ß TaPf3 (monoclinic, new type). TaPt2 and TaPt3 melt congmentlv; two eutectic, two beritec-tic, and one eutectoid reactions occur in the inuestigated range. THE Ta-Pt system was examined as part of a study of the phase diagrams and the intermediate phases of niobium and tantalum with Group VIII transition metals. Since the main scope of this work was the relation among the ordered close-packed phases occurring in the concentration range from AB to AB3 (A = Nb, Ta; B = Pd, Pt, and so forth), only the platinum-rich side of the diagram was worked out thoroughly, while spot checks were made to determine the approximate outline of the tantalum-rich portion. The system has not been thoroughly treated in the literature; Greenfield and Beck1 in their survey of refractory metal intermediate phases found a o phase between -18 and 37 at. pct Pt which coexists at higher platinum concentrations with an unidentified intermediate phase. Browning2 worked on the range between 55 and 100 at. pct Pt; however, this preliminary study did not cover temperatures >1500°C, and included no conclusive crystallo-graphic data. More recently, a study of the platinum-rich section of the Ta-Pt system has been carried out by Ray,3 while Hartley, Parsons, and steedly4 have studied the tantalum-rich section. The crystal structures of TaPt2, a TaPt3, ß TaPt3, and others have been reported in abstracted form by Giessen and Grant.5 EXPERIMENTAL METHODS The methods of alloy preparation and processing and of the metallographic and X-ray procedures follow very closely those described by Ritter, Giessen, and rant' for other refractory metal-noble metal systems, and will not be repeated except where significant differences exist. Starting materials were: tantalum rod of 99.95 pct purity, supplied by National Research Corp., and platinum sponge 99.9 pct, supplied by The International Nickel Co. An oxygen analysis of the tantalum rod showed 30 ppm O; other impurities were C, N, Si, Nb, Mo, none of these exceeding 50 ppm, and 100 ppm W. Homogeneous buttons were readily prepared as follows: ingots of 5 g were weighed and arc-melted under welding grade argon, followed by two remelts after inverting the button. Between 40 and 100 at. pct Pt, weight losses during the first melt rarely exceeded 0.1 pct, in which case the alloy was rejected, and were nil on subsequent remelts. Since the vapor pressure of platinum far exceeds that of tantalum, the small evaporation loss could be assumed to consist of platinum; therefore, a corresponding amount of platinum was added on the second melt. Since it was confirmed on pure tantalum samples that no weight gain through oxygen or impurity pickup occurs (see Ref. 71, it could be assumed that the uncertainty in the composition did not exceed ±0.1 at. pct for the range 40 to 100 at. pct Pt. For the four control melts from 0 to 40 at. pct Pt, an error of ±0.5 at. pct was calculated. Microscopic examination of the whole buttons after melting showed no inhomogeneity other than local coring. This was eliminated by a homogenization heat treatment. A total of twenty-three alloys were prepared. Heat treatments were carried out in a tantalum

Jan 1, 1965

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By W. C. Ellis, E. S. Greiner, M. E. Fine

Discontinuous changes of Young's modulus, internal friction, coefficient of expansion, electrical resistivity, and thermoelectric power are evidence for a transition in chromium near 37OC. Although the X-ray diffraction pattern gives no clue, a difference between the thermal expansivity and the temperature dependence of the lattice parameter suggests a crystal-lographic change. Young's modulus data disclosed another transition near THE thermal dependence of a number of proper- ties of chromium indicates a transition occurring over a temperature range near room temperature. Bridgman' noted this first from a minimum in the electrical resistivity near 12°C. In a sample of greater purity, Sochtig' observed the minimum at 41 °C. Erfling3 reported an inflection in the thermal expansivity curve at 36°C. These temperature-dependence curves are reversible with no hysteresis being detected. No discontinuity or inflection has been observed in the heat capacity' or the paramagnetic susceptibility.' Likewise, no one has noted a change in crystal symmetry. In the present investigation Young's modulus, internal friction, coefficient of expansion, electrical resistivity, illustrated in Fig. 1, lattice constant, Fig. 2, thermal electromotive force, Fig. 3, and paramagnetic susceptibility, Fig. 4, were measured over an extended temperature range. The samples were prepared in two ways: (1) By cold pressing a sintered electrolytic powder compact,' and (2) by electroforming from an aqueous solution. The electroformed samples were prepared by R. A. Ehrhardt and G. Bittrich by plating on copper or nickel tubes from an aqueous solution according to the method of Brenner, Burkhead, and Jennings.' The pressed powder samples (method 1) were finally annealed at 1400°C in purified helium: the electroformed samples, packed in powdered chromium, were vacuum-annealed at 1000°C. From the composition of the original powder' the purity of the pressed powder samples is estimated to be 99.8 pct Cr. Spectrochemical analysis furnished by E. K. Jaycox, revealed only slight traces of impurities in the electroformed sample (less than 0.001 pct), neither iron nor nickel being detected. Chromium deposited by this method is reported to contain approximately 0.05 pct 0.- Methods and Data Young's Modulus: For measurement of Young's modulus, an annealed, pressed powder sample, 0.114 x0.237x1.845 in., and an electroformed sample, 0.10 in. od, 0.01 in. id, and 1.86 in. long, were prepared. The resonant frequencies of the rod samples in forced longitudinal vibration were measured at a series of temperatures from —192" to 200°C by a method previously de~cribed.6,7 Because the samples were nonferromagnetic, iron- silicon or molybdenum permalloy tips (0.013 in. thick) were soldered to the ends. The softening temperature of the solder limited the temperature of measurement. Young's modulus, E,, of chromium at temperature, T, may be calculated from the resonant frequency of the composite rod, f,; the thickness of the tips, t; the length of the chromium sample at 25°C, l,.; the density of chromium at 25°C, pc (7.20 g per cc);5 and the thermal expansivity, Al/l25. Modulus differences for two temperatures, ET and E, are accurate to +0.002x10" dynes per cm2. ET = 4PAlc+2tyf Young's modulus at 25°C, Fig. la, is 28.2~10" dynes per cm' (40.8xlO" si) in wrought chromium (upper curve). The modulus of the electroformed sample is apparently lower due to cracks. From the modulus measurements two transitions were observed: one with a critical temperature at 37°C, the other at —152°C. Internal Friction: The internal friction, 1/Q, was determined from the width, Af, of the strain amplitude-frequency curve at 0.707 times the strain amplitude at resonance;' the internal friction, 1/Q, then equals Af/f. Fig. lb shows a sharp peak in internal friction at 38°C. The internal friction of the electroformed sample had a similar maximum. Thermal Expansion: The expansivity measurements, shown in Fig. 2, covering the temperature range —195" to +400°C were made by D. MacNair in an interferometric dilatometer8 sing a sample consisting of three pyramids 0.25 in. high prepared from wrought electrolytic chromium. Below —120°C the experimental points deviated up to ±2x10 from the drawn expansivity curve in Fig. 2 because of decreased precision of the quartz wedge thermometer at low temperatures. Near 38°C the thermal expansivity curve, Fig. 2, goes through an inflection corresponding to a minimum in the coefficient of expansion, Fig. ld, and a relative volume decrease on heating. Electrical Resistivity: The variation of electrical resistivity with temperature measured by the po-tentiometric method is also shown in Fig. l. The resistivity of the wrought chromium (upper curve) at 20°C is 13.6 microhm-cm; of electroformed chromium (lower curve) 12.8 microhm-cm. The lower value reflects higher purity and agrees closely with a published value." A minimum at 40°C occurs in the resistivity curves of both samples. No conclusive evidence for a transition near — 150°C was observed, but the points, Fig. 1, appear to deviate from a smooth curve between —120" and —160°C.

Jan 1, 1952