Search Documents

By G. S. Scott, G. W. Jones

Economic waste caused by mine fires may become considerable,l5 especially if a fire is allowed to spread or temporarily to get beyond control. It is important, therefore, to act promptly whenever a fire is suspected and to make every action count. To contribute toward its extinction effectively it is necessary to know at the earliest possible moment, and continuously thereafter, what is happening at the seat of the fire, which may be in a remote or inaccessible area, and also to recognize what may be expected as a result of any proposed combative measure. In combatting a fire the mining engineer and the chemist should cooperate, first deciding upon the course of action to be taken and then drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required to carry out proposed operations, and the probable efficiency with which these operations could be performed, and upon the chemist's knowledge for the results to be expected therefrom. After the initial steps to be taken have been decided, it devolves upon the mining engineer to see that they are carried out and upon the chemist to evaluate the results and to keep the mining engineer continuously informed in regard to a variety of matters—such as the composition and toxic or asphyxiating properties of the atmosphere in which the men may be working, whether the fire is increasing or decreasing in intensity and its probable temperature, the quantity of air leakage and the explosion hazards of the fire area. The purpose of this paper is to discuss what the chemist can and cannot contribute as a member of the fire-fighting personnel. The technical literature contains several hundred papers relating directly and indirectly to mine fires, and this fact alone is testimony to the complex nature of the phenomena involved in the birth, life, and final demise of a fire. A fire may be stopped (I) by preventing oxygen from reaching the coal or (2) by removing the conditions necessary for the rapid reaction of coal with oxygen; i.e., decreasing the temperature. All methods of prevention or control necessarily must be based upon one or the other, or both, of these two principles. The chemistry of a fire may be understood readily if the low-temperature oxidation of coal is considered as a starting point; then oxidation at higher temperatures (or combustion); and with these, the composition of the solid and gaseous products resulting from the oxidation or from the effects of the heat liberated. This discussion refers particularly to Pennsylvania anthracite, although much of the material applies equally well to coals of lower rank. Oxidation of Coal Oxidation of coal fundamentally is confined to the surface; that is, the rate at which oxygen penetrates into the interior of a solid block of coal is so slow that it may be ignored."16 Oxidation starts when a fresh surface is exposed, and the rate is

Jan 1, 1942

By J. K. Elliott, P. H. Kelly

Many engineering functions such as surface metering work and laboratory compressibility check points involve the use of liquid densities of light hydrocarbon mixtures at various pressures and temperatures. However, at the present time, no simple reliable method exists for determining density variation, particularly if the composition of the liquid is unknown. Consequently, a study was undertaken to develop and present a simple and accurate method of predicting density variation of a light hydrocarbon liquid with pressure and temperature, knowing only the density of the liquid at some condition. The experimental liquid compressibility data from API Project 37 by Sage and Lacey' have been considered to be accurate within 0.5 per cent and cover a wide range of pressure (14.7 to 10,000 psia), temperature (100" to 400°F) and molecular weight (up to 150). From these data, a set of liquid density curves, which relate density to pressure, temperature and molecular weight, was developed. These curves make it possible to predict density variation with pressure and temperature. Compared to extensive laboratory compressibility data on a complex, light hydrocarbon liquid, the use of the liquid density curves resulted in an average error of less than 0.5 per cent. Based on the results of this analysis, it is concluded that the set of liquid density curves developed from the data of Sage and Lacey provides an accurate and simple method for predicting the density variation of light hydrocarbon liquids when the density at some condition is known. These curves should be very helpful in many engineering calculations, particularly in the surface metering of light hydrocarbon liquids. INTRODUCTION Many situations arise in field and engineering laboratory work, such as reservoir engineering studies, check of experimentally determined laboratory data and orifice flow-meter formulas, where liquid density factors at various pressure-temperature conditions are required. Also, the need for accurate light hydrocarbon liquid information has become more important with the advent of miscible-type displacements for secondary recovery purposes in oilfield operations. Several reliable methods are available1 - "or determining the density of liquid hydrocarbons if the composition of the liquid is known. However, there is a definite lack of methods for accurately determining the variation of density when the composition of the liquid is unknown. The purpose of this study is to review the various methods for determining hydrocarbon liquid densities and to develop a simple and reliable method of determining variation in density of light hydrocarbon liquids with pressure and temperature when the compositio~n of the liquid is unknown. METHODS FOR DETERMINING DENSITY OF LIQUIDS OF KNOWN COMPOSITION Sage, Lacey and Hicks' have proposed a method to predict the density of light liquid hydrocarbons by using partial molal volumes. Data are available on experimentally developed partial liquid volumes of hydrocarbons over a rather limited range of temperature, pressure and composition. The partial mold volume method has proved satisfactory for determining the density of some hydrocarbon liquids when the composition is known. Within the range covered in the Sage, Lacey and Hicks1 data, the results agree within about 3 per cent of the experimental values. Hanson mentions the limitation of this method to a composition range of approximately 10 per cent by weight of methane, which will not allow this correction to cover most low molecular weight-light hydrocarbon liquids. Standing and Katz2 studied data on light hydrocarbon-liquid systems containing methane and ethane at high temperature and pressure and have presented a method for determining liquid densities, assuming additive volumes for all components less volatile than ethane and using apparent densities for methane and ethane. The compressibility and thermal-expansion curves used by Standing are based on assumptions that compressibility of a hydrocarbon liquid at temperatures below 300°F is a function of the liquid density at 60°F and that thermal expansion of the liquid is affected little by pressure. The information required to use this technique with an example problem is furnished by Standing.' Hanson eports an average error of - 0.5 per cent using the method of apparent densities in calculating liquid densities of several volatile hydrocarbon mixtures. However, as implied, the apparent density method is not applicable for liquid density calculations when the composition of the liquid is unknown. Watson- as presented a method

By W. A. Boyer

MINE hoisting ropes can be loaded to capacity only when the strength of each component is exactly known. Characteristic curves provide this information. When load and rate of acceleration are specified for an individual rope, the characteristic curve assumes a predetermined shape. The factor of safety, is the value drived by dividing the breaking strength of the rope by the total stress on the rope where it goes over the sheave wheel. Total stress is made up of the weight of skip and cage, weight of ore, weight of rope between sheave and rope clevise or attachment, friction load, and acceleration force. Bending stresses are neglected in this discussion, as sheaves and drum di- ameters are assumed to be large enough to reduce these stresses to a negligible value. Fig. 1 gives a family of characteristic curves for 13/8-in. improved plow steel hoisting ropes of 6 x 19 or 6x21 construction with hemp core. The curves will hold for all rope sizes of this specified quality when they are subjected to an acceleration rate of 1.608 ft per sec2. As acceleration rates of most deep shaft hoists are close to this value, this family of curves is presented as a standard. Deviation is slight for other rope sizes. Note that for 0, which is the most important, the deviation is within the width of the line on the graph. In a comparison of values for ropes of 5/8-in. and 21/4-in. diam the deviation ranges from a maximum 1.2 pct at 0 ft to 0.6 of 1 pct at 5000 ft. The value of 5.55 is the same for all ropes at 2500 ft. The tabulated columns to the left of the curves are values of total connected load for each size of rope from 5/8-in. to 21/4-in. diam inclusive. With each of these connected loads the safety factor characteristic curve for the rope will be as indicated.

Jan 1, 1957

By F. Keller, A. H. Geisler

Some of the important changes that take place in the structure of aluminum alloys are largely submicroscopic in character. This is especially true of the changes that accompany age-hardening and recrystallization. Although improved metallographic practices have been helpful in indicating some of these changes indirectly, results are limited by the resolving power of optical microscope lenses. The electron microscope, however, provides a new and important means for investigating the fine structure of metals in a range not possible heretofore. It is anticipated that this microscope will yield new and useful information to metallurgists when suitable techniques are developed to utilize its very high resolving power. Several unique methods have been devised to permit the examination of the structure of opaque samples by the electron microscope. These are all based on the principle of producing a very thin film that represents the prepared surface of the opaque metal sample, which can be examined in the transmission microscope; however, the available methods fall into three categories, depending on the manner in which the film is obtained. With the oxide-film method developed by Mahl3-17 a very thin surface layer of the metallographic sample is converted into oxide by a thermal, chemical or anodic treatment. After removal from the metal sample by one of the special techniques described by Evans,19 this oxide film is examined in the electron microscope, and is found to portray the structure of the original metal surface. Films formed on aluminum,8,17 nickel,7 iron 3,8,9 and a nickel-beryllium alloy" by heating; films formed on iron 8.9 by chemical action; and films formed on aluminum3-16 by anodic oxidation, have been examined. The other two are more recent methods developed principally in this country; they consist in making the thin film in the form of a mold or replica of the surface contour of an etched sample. With the negative replica method the thin film is made directly on the sample; with the positive replica method it is made on a negative reproduction of the sample. With both methods, variations in the contour of the metal sample, caused mainly by etching, produce variations in the thickness of the surface replica. Because of the direct dependence of the amount of scattering of the illuminating electrons upon the thickness of the film penetrated, only the variations in thickness of the replica are responsible for tones in the electron image. Negative replicas are made by forming a thin film of some suitable material directly on the polished and etched metal sample, and derive their name from the fact that after removal from the sample they have the high and low points in the sample reversed, as shown in Fig. I. Nega-

Jan 1, 1944

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. L. Corp, J. C. Johnson, W. G. Pariseau, M. Poad, M. E. Fowler

This paper describes a comprehensive geomechanics case study of a full¬scale test stope at the Carr Fork Mine. The mine is owned by Anaconda Miner¬als Company and is located near Tooele, Utah. Large diameter blast holes were used in a new method known as blast hole post-fill (BHPF). The new design proved highly successful in contrast with earlier experience with vertical crater retreat (VCR) stopes. The main geomechanics objective was the estab¬lishment of a design procedure for optimizing stope and pillar dimensions with respect to productivity and recovery. An integrated three-part approach consisting of mine measurements, laboratory testing and finite element calcu¬lations was taken. Independent correlations of 0.88 and 0.89 between calculated and measured displacements and between estimated and observed yield :ones substantiate the finite element design approach using UTAH-II. Subse¬quent stope and pillar design analyses indicate that doubling of the original stope width at 50% extraction is quite possible without sacrifice of safety or stability.

Jan 1, 1984

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. Robert W. Hunt Medal and Prize THE partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes: first of a gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or papers on iron and steel. The scope of the term "iron and steel" shall be determined by the subcommittee considering the awards. In general, papers dealing with the practical side of the subject have preference over those dealing with the theoretical side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A subcommittee of three to five, including the Chairman of the Iron and Steel Division, shall be appointed by the Iron and Steel Division annually to adjudge the award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of .the Institute. 5. The recipient of the award shall be designated "The Hunt Medalist." Awards of the medal have been made as follows: 1920—-Robert Woolston Hunt. 192G—John A. Mathews. 1926—Charles Lewis Kinney, Jr. 1929—Edgar Collins Bain. 193G—James Aston. Awards of the prize have been made as follows: 1928—C. H. Herty, Jr. 1929—William E. Griffiths.

Jan 1, 1930

By H. J. Rose

SIXTY-FIVE million net tons of coal were carbonized in the by-product and beehive coke ovens1 of the United States during 1924. This tonnage represented 13.4 per cent. of the bituminous coal which was mined in that year. Table 1 shows production and disposition.2 TABLE 1.-Production and Disposition of Oven Coke in 1924 BY-PRODUCT BEEHIVE TOTAL Coal charged into ovens, tons 49,061,339 15,914,310 64,975,649 Coke produced (exclusive of screenings and breeze), tons 33,983,568 10,286;037 44,269,605 Average yield of coke, per cent 69.3 61.6 68.1 Disposition of coke: PER PER PER CENT. CENT. CENT. Blast furnace 82.5 82.8 82.6 Foundry 4.6 13.3 6.6 Domestic 8.3 1.4 6.7 Water gas manufacture and all other uses 4.6 2.5 4.1 Cokes having somewhat different combinations of chemical and physical properties are desired for the various uses listed above, and these properties depend primarily upon the types of coal used. American coals have a wide range of purity and coking quality, and the chief subject of this paper will be the selection of coals for the manufacture of blast furnace, foundry, domestic, and water-gas coke, in by-product coke ovens. It will obviously be necessary to include a discussion of those physical and chemical characteristics that are generally considered essential or desirable for each type of coke.

Jan 7, 1926

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

By Max Boehmer

(Pittsburg Meeting, March, 1910.) AFTER 30 years of development and after an output of $350,000,000 in value of gold, silver, lead, zinc, and copper, there has not been published a satisfactory explanation of the origin of the immense deposits of the Leadville district. The original examination find survey of Leadville by members of the U. S. Geological Survey was a most magnificent piece of work, but their attempt to explain the origin of the ores was based upon the then-accepted theory of lateral secretion, originated by Sandberger, which theory was afterwards disproved in many cases by further development in numerous districts. This theory contended that the ore in the veins had been leached by surface-waters from the eruptive rocks in the immediate vicinity, and it had its origin in the fact that the neighboring eruptive rocks all contained, to an appreciable degree, the several metals found in the ore-deposits. But the practical miner, reasoning in a simple manner from the condition of things as he found them underground, soon discovered the fallacy of this proposition. He reasoned that, in the case of the Leadville deposits, this theory could not be true, because, if the ores were leached from the overlying eruptive rocks by surface-waters, they would as a matter of necessity be controlled by the action of gravity, and the main bodies would collect in- natural depressions of the underlying limestone, and at all points where such depressions existed. But this was not in accord with the channels of ore as he found there ; and hence the theory of lateral secretion in this district was never accepted. Another objection to it consisted in the fact that large areas within the ore-bearing district contained no ores whatever, although their formation was the same, and the same limestones were covered by the same thick sheet of

Feb 1, 1910

By Dewey J. Sabin

THE Rio de Canada Honda placer property is situated at an altitude of 5500 ft. above sea level in the San Luis Mountains of the Province of San Luis, Argentina. The mine is reached by 70 km. of fair truck road, from the nearest railway station on the Ferrocarril Buenos Aires al Pacifico. The Pan-American airport at Villa Mercedes, 1.40 km. distant, serves as the most convenient point for shipment of gold. Placer mining in the Rio de Canada Honda dates from the time of the Incas and the present native population depends on the gold washed from this river and the adjacent arroyos as a means of livelihood as did the many generations before them. They dig pits to bedrock where they are not driven out by water, and mine the bedrock gravel by means of tunnels and caves. No timber is available and the ground is supported by rock cribs carefully built with the boulders encountered; or with angular blocks of slate rock taken from quarries on the surface.

Jan 1, 1936

By K. R. Janowski, A. B. Chase, E. J. Stofel

Ruby crystals of exceptional optical quality have been grown from fluxes composed of Bi2O3 + PbF2 or Bi2O3 + BiF3. Careful control of growth conditions was required to minimize the number of growth defects consisting primarily of dislocations, occluded flux, and growth twins. Slow growth rates coupled with the addition of small amounts of La2O3 as a flux dopant were helpful in producing nearly perfect crystals. Chromium concentrations up to 1 pet were incorporated into these crystals without adversely affecting their perfection. Crystals up to 10 mm in diameter having as few as one to ten dislocations per crystal were typical of those produced under optimum growth conditions. Under these same conditions the occlusions were eliminated, and growth twins were either eliminated or reduced to one to three twin boundaries per crystal. INTEREST in the nature of lattice imperfections produced during the growth of ruby crystals (Al2O3-corundum structure) has been stimulated recently by the need for ruby lasers of good optical uniformity. As a result, ruby crystals grown by the flame-fusion (Verneuil) process have been studied in detail and have been found to contain high densities of dislocations (106 to 107 dislocations per sq cm) and mosaic structures that impair their optical quality.'-3 Attempts to improve the quality of Verneuil-grown crystals by controlling the growth variables have not been entirely successful. On the other hand, rubies grown by the flux process have received little attention even though their more nearly equilibrium growth conditions suggest that they would have fewer growth defects. Nelson and Remeika have shown recently that small flux-grown rubies can indeed be made into very low-loss lasers. However, they did not report information on crystalline imperfections in these crystals.4 Stephens and Alford have reported briefly on defects found in a flux-grown corundum crystal but they neither described these defects in detail nor related them to the method of growth.5 The present investigation was undertaken to establish the relationship between growth conditions and crystalline perfection of flux-grown rubies, sapphires, and other crystals of the corundum family. EXPERIMENTAL PROCEDURE The corundum crystals used in this study were grown by slowly cooling solutions of A12O3 in molten-salt solvents of PbO + PbF2, Bi2O3 + PbF2 or Bi2O3 + BiF3. The materials employed were Linde A (a Al2O3 powder) with reagent-grade chemicals as solvents. Some of the solutions also contained small additions (1 pet or less) of one or more of the transition metal elements chromium, manganese, iron, and titanium as crystal dopants. La2O3 was added to some of the solutions to alter the growth habit of the crystals. The La2O3 promoted the occurrence of growth facets parallel to (0112) and {1011} planes, where the indexing system is the morphological system described in detail by Kron-berg6 and used throughout this paper. The melts from which the crystals were grown were prepared by mechanically mixing the various constituents and placing them in platinum crucibles. The covered 50- and 100-ml platinum crucibles were heated in muffle furnaces at 1250°C for short periods of time (1 to 4 hr) and then program-cooled at either 2° or 4°C per hr to 1000°C. At this lower

Jan 1, 1965

By Petri Bryk, John Ryselin, Rolf Malmstrom, Jorma Honkasalo

THE theoretical possibilities for the realization of flash smelting have been known for a long time. Calculations concerning the same can be found in previously published literature,1 and suggestions for its accomplishment in practice are described in patents on the subject. Likewise a smaller number of practical test results are known. Autogenous smelting is closely connected with flash smelting, since in flash smelting techniques it is possible to use the heat evolved by oxidation of the sulfides for the smelting process to such an extent that under certain conditions smelting can proceed without additional fuel. However, in the event that insufficient heat is available from the oxidation of the sulfide concentrates, then additional heat may be supplied by preheating the air, using oxygen enriched air, on burning additional fuel with the concentrate.

Jan 6, 1958

By Donald F. Saunders

Means and relative standard deviations were calculated for eU, eTh, K, and their ratios for aerial gamma-ray spectral data in 29 quadrangles at 1:250,000 scale. Known or suspected uraniferous provinces were characterized by: 1) Higher eU, eTh, and K means (due to generally higher radioelement concentrations); 2) Higher relative standard deviations for eU, eU/eTh, and eU/K (reflecting the presence of local uranium enrichments); and

Jan 12, 1979

By Morton Macartney

FOR many years the developers or owners of worthy mining ventures in need of financing have found it almost impossible to obtain such financing under the conditions existing in most other lines of business. High rates of interest and unfair participation in profits have robbed the developers of much of their holdings, and have resulted in over-capitalization and many other like evils. When the general financial condition of the country is bad, this difficulty increases to a point where many operations must cease and hen are thrown out of employment. In 1.934 this situation had developed to such a point that Congress attempted to aid the mining industry. It first authorized the RFC to make loans to recognized and established corporations, individuals, and partnerships engaged in the business of mining, milling, or smelting of ores in June, 1934, limiting such authority to loans adequately secured, the security to consist of mineral acreage. The requirements of the law were stringent and of the 252 requests for loans received up to June 1, 1935, 35 were authorized.

Jan 1, 1936

Extremes in temperature and weather, along with the highly corrosive nature of acid leach solutions used at open-pit copper mines, necessitates the use of pipeline systems that are both corrosion resistant and impervious to the environment.

Jan 6, 1976

By Evans B. Mayo

This study examines the structural framework of the Southwest for evidence of the four principal trends of lineament tectonics. It attempts to classify their intersections and compares the positions of those trends that appear most favorable with the positions of the presently known mining districts. This is a controversial topic. The author, in presenting his analysis, is aware that the study of lineament tectonics and relation of ore districts to regional structure is complicated by insufficient data and, unavoidably, by personal bias. The development of lineament tectonics has been summarized by Umbgrove.' Early attempts to fit ore districts into the Cordilleran framework were made by Billingsley and Locke, who do not refer to lineament tectonics, although their appoach is similar; they observe that heat and fluids, including the ore-depositing fluids, are most likely to rise at or near intersections of major structures where the crust is fractured, or weakened, to great depth. As a result of studies distributed over the earth-including ocean basins as well as continents— some tectonists recognize four dominant structural trends: 1) northwest; 2) northeast; 3) nearly east-west, or equatorial; and 4) nearly north-south, or meridional. Baker' proposed a theory to account for these trends and Sonder" called their world-wide arrangement the regmatic shear pattern. Moody and Hill proposed a much more complicated shear network which, although fascinating and perhaps ultimately useful, will not be followed here. In a recent review of deformation within the Cordillera, Wisser mentioned the four fundamental directions. The fact that many geologists deny the existence of the regmatic shear pattern implies that the fundamental structures are far from obvious. It may mean, also, that some geologists are not accustomed to examine regional and world maps analytically. The maps require much study, and certain features should be isolated on overlays. Even so, with the present limited knowledge, uncertainties remain. The following analysis is a qualitative experiment, subject to change as information accumulates, and should be supplemented by the western sheet of the Tectonic Map of the United States.' Many have probably gained the impression that the Cordillera of the West is oriented northwest-southeast and from this, unless experience rules otherwise, it is natural to assume that the structure likewise trends northwest-southeast. To an important extent this is true, yet anyone tracing off the western sheet of the Tectonic Map all the recorded north west-southeast structures may be surprised to see what a small part of the entire area they occupy. In southwestern U. S. (Fig. 1) the northwest-southeast structures are mostly restricted to the eastern, southern, and western parts. The eastern margin of the Cordillera from northern Colorado to the International Boundary near El Paso, Tex., is obviously determined by some structure other than northwesterly ones. In eastern Nevada and far southward toward the Gulf of California many mountain ranges, valleys, and faults are meridional. In the Rocky Mts. of Colorado, and at many places in southern Arizona, the crystalline Pre-Cambrian is foliated northeast-southwest. The Uinta Mts. of Utah trend approximately east-west, in much the same way as a broad belt of transverse, west-northwest structures—the Texas lineament of Hill",' and Ransome10 in southern Arizona, southwestern New Mexico, and southern California. It seems, then that there are four regmatic shear directions in the Southwest, but at many places they are discontinuous, and their projections must be inferred. To clarify these trends the four sets have been isolated into two systems: 1) northwest-northeast and 2) east-west-north-south (Figs. 2 and 3). Northwest-Northeast System: A number of prominent northwest-trending zones of structure are easily recognized. They are designated by circled Roman numerals, the northeast-trending structures by circled capital letters. Perhaps no two geologists would agree completely on the positions of all these belts. Names given below are for convenience only, and may be discarded where other names have priority. (I) The Sierra Nevada-Lower California belt contains the Jurassic-Cretaceous granitic massifs of the Sierra Nevada and Lower California. These

Jan 1, 1959