Search Documents

By M. R. Tek, K. H. Coats, D. L. Katz

In natural gas storage operations, seasonal pressure fluctuations in the gas reservoir cause the water from the surrounding aquifer to flow into and out of the gas sand. The theory of unsteady-state liquid flow through porous media developed by Van Everdingen and Hurst' has been applied to predict the water movement into and out of the gar bubble for .several .postulated pressure cycles. Those cycles with as many pound-days above the original aquifer pressure as pound-days below, may cause the gas reservoir to slowly grow or shrink rather than hold to a constant volume. Applications to an actual field case study give the predicted gas reservoir monthly pressures and volumes as compared with the observed monthly pressures and volumes. INTRODUCTION A large number of natural gas storage reservoirs are bounded by or adjacent to large water-saturated formations called aquifers. The presence of these aquifers is usually evidenced by the production of water from wells delineating the gas-hearing sands. Some gas storage reservoirs in use today have been purposely developed on aquifers. Cyclic pressure variations in a gas storage reservoir cause water influx and efflux from the surrounding aquifer. This, in turn, results in a varying gas reservoir volume. The prediction of the effect of this aquifer fluid movement on the size and size variation of the gas reservoir can provide information valuable in the study of several reservoir engineering problems. The economics of gas storage operations are directly influenced by the influx of aquifer fluid into the reservoir since a shrinking storage reservoir requires increasing pressures for the storage of the same quantity of gas. Material balance and reserve or recovery calculations also obviously require knowledge of reservoir volume. Various other reservoir engineering calculations such as interpretation of well interference data, evaluation of physical characteristics of porous media, water coning, gas injection and pressure maintenance studies are typical problems where variations of volume due to edge or bottom-water encroachment becomes important. The solution of equations describing influx and efflux of water in the gas sand, application to gas storage reservoir behavior and interpretation of results are the main objectives of this paper. While this work was directed toward gas storage reservoirs, it applies equally well to repressuring of partially depleted oil reservoirs with an active water drive. MATHEMATICAL ANALYSIS As just mentioned, the cyclic pressure variations in an aquifer-surrounded gas storage reservoir cause water movement and varying gas reservoir volume. Prediction of this volume variation from the reservoir pressure cycles or the injection-production schedule requires adoption of a flow model, certain assumptions concerning reservoir and fluid properties, and formulation and solution of the governing differential equation. The flow model used in this study is a gas bubble located on a very large aquifer (Fig. la). Gas bubble radius and aquifer sand thickness are denoted by rr and h, respectively. Fig. lb shows the horizontal, radial two-dimensional porous reservoir attended by the unsteady, compressible motion of the aquifer liquid. Volume variation of the gas bubble is determined from aquifer water flow across the cylindrical boundary, r = r0

By Maurice Ewing, J. A. Peoples, J. W. Peoples, A. P. Craby

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By Gerald Sherman

IN the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40° to 50° from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increas-ing, as they avoid the maintenance' of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation,' the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it, out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver's whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Opera-tions while driving 195 ft. of this tunnel using a scraper loader were care-fully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration if was found most convenient to use a scraper loader.

Jan 1, 1936

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZg2, (formerly ASTM No. 17; also known as Dowmetal C or AM26o) which was done under "Restricted" Project NRC-2I, in 1942-1943, and reported in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat- treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZp was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZp, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray 'analysis. From this figure it may be seen that above approximately 375°C (707OF), AZp alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, ancl because of its solubility relations, AZqz resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ² alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1949

Jan 1, 1929

By J. T. Lapsley, I. I. Cornet, A. E. Flanigan, R. Hultgren, J. E. Dorn

WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that procedures of heat treating common magnesium casting alloys be investigated systematically. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. Research on the solution heat treatment and aging of magnesium alloy AZ92, (formerly ASTM No. 17; also known as Dowmetal C or AM260) which was done under "Restricted" Project NRC-21, in 1942-1943, and reported, in detail in a final report to the OSRD on September 3, 1943, is the basis of this paper, which has been released for publication by the OSRD. American experience with magnesium alloys prior to World War II was limited, although some of these alloys had been in commercial use since 1909. Requirements of the aircraft industry for light alloys made it imperative to understand and utilize the advantageous strength-weight properties of magnesium castings. Magnesium casting alloys are commonly solution heat treated to increase their ultimate tensile strength and ductility; this treatment may be followed by an age hardening at elevated temperatures, which raises the tensile yield strength but diminishes the ductility. In the present investigation, AZ92 was studied to determine the effects on properties of various solution heat treatment and aging schedules. The principles of heat treatment of magnesium alloys are the same as for other non-ferrous alloys. The alloy studied, AZ92, has a nominal composition of 9 pct aluminum, 2 pct zinc, and minor constituents. Fig I shows, by the projection of isothermal sections on the concentration plane, the solubility surface1 of the ternary magnesium-rich solid solutions as determined by X ray analysis. From this figure it may be seen that above approximately 375°C (707°F), AZ92 alloy is a single phase alloy at equilibrium; below this temperature the equilibrium condition is a. two phase alloy. The beta constituent which precipitates from the solid solution exerts a hardening effect. Because the zinc concentration is only 2 pct, and because of its solubility relations, AZ92 resembles a binary alloy of magnesium with aluminum. The solubility curve1 of Fig 2 shows how rapidly the solubility of the beta phase decreases with decreasing temperatures. Unlike many aluminum alloys, magnesium alloys do not age harden at room temperatures; precipitation hardening of AZ92 alloy is performed at about 177°C (350°F). At this temperature about 3 pct aluminum

Jan 1, 1947

By R. H. Fillnow, D. J. Mac

IT has been demonstrated that alloys in systems structurally analogous to steel undergo reactions during heat treatment similar to those of steel, and yet very little work has been done on such systems, particularly from the standpoint of isothermal transformation. The literature shows that most of the isothermal work has been done on copper-alu-minum alloys.'-3 One paper has been reported on a eutectoid copper-silicon alloy,' and one on iron-nitrogen alloys.' There are no published reports of previous investigations on the isothermal transformation of a eutectoid beryllium bronze. At least two papers have been reported on isothermal age-hardening phenomena in beryllium-copper alloys of lower beryllium content.5,6 No information on eutectoid transformations in this alloy is given in Rimbach's book, "Beryllium." ' This paper reports the results of an investigation on the isothermal transformation characteristics of a eutectoid beryllium bronze. Materials Used and Procedure The eutectoid beryllium bronze used in this investigation was centrifugally cast at the Ampco Metal Co., Inc.. Milwaukee. Wis. A master beryl-lium-copier alloy, purchased from the Brush Beryllium Co., was used to make the beryllium addition to the copper. The alloy was melted under a protective carbon cover and Centrifugally cast into a graphite mold preheated to 920°F. Some trouble with segregation of beryllium in the melt was encountered but was eliminated by violent stirring during melting and pouring. Since very thin .specimens were used for the various heat treatments, only one casting of the four prepared was necessary for the complete isothermal study, thus eliminating any discrepancies caused by a change in composition. The analysis of this casting was 94.035 pct copper and 5.965 pct beryllium. A slight trace of iron was found. The castings were sawed into specimens approximately 3/32 in. in thickness. The specimens were first given an "austenitizing" heat treatment at 788°C, well within the single phase beta region, in a vertical tube furnace. The specimens were then quenched individually into an adjacent molten salt bath and held there for a definite time, after which they were quenched into water at room temperature. Temperature was held to ± 2°C in the salt bath. No homogenizing treatment was given the specimens other than the soak at 788°C. Despite the fact that this was a cast alloy, no evidence of segregation or coring was found in the microstructure of any specimen, either as cast or as heat-treated. Upon completion of the heat treatment, the speci-mens were subjected to metallographic examination

Jan 1, 1951

Discussion of the papers of Messrs. Howe and Levy, Burgess, Crowe and Rawdon, and H. M. Howe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1075 to 1136. ALFRED STANSFIELD, Montreal, Canada :-In Professor Howe's paper on the position of Ae3, he shows its industrial importance in determining the temperature to which steel should be heated. for "grain refining." Several years ago I carried out a research on the " burning " of steel and found that while hypo-eutectoid steel should be heated to Ae3, hyper-eutectoid steel that has been very much overheated must be reheated to the curve Sa on the carbon-iron diagram, in order to redissolve the pro-eutectoid cementite and thus, to obtain recrystallization and grain-refining. This treatment was necessarily only partly successful, and I should like to ask whether the conditions of heat treatment for refining overheated high-carbon steels have been ascertained. Speaking of the " Persistence of Solidificational Segregation " Professor Howe quotes an experiment made by Mr. Stead in which a bar of 1.2 per cent. carbon steel was immersed in a large mass of molten blast-furnace slag and allowed to cool with it. The steel was heated above the solidus (curve Aa on the carbon-iron diagram), but below the liquidus (curve AB). A drop of eutectic carbon-iron alloy, rich in carbon, had liquated out and hung below the bar. This agrees exactly with my own observations on the burning of steel, but my interpretation differs somewhat from that of Professor Howe. Professor Howe considers that the fusion of a part of the metal (rich in carbon) shows that the solidificational irregularities of composition had persisted through the rolling and heat treatment of the steel, as otherwise no part of the steel would have been sufficiently fusible to melt. It does not appear to me that such an explanation is necessary. A piece of steel represented in temperature and composition by any point within the area ABa will ultimately resolve itself into a solid phase and a liquid phase in equilibrium with each other. It may appear that if the steel were absolutely uniform no fusion could take place, but the smallest nucleus of high-carbon, fusible alloy would ultimately bring about this separation into liquid and solid phases, by diffusion of the carbon from the solid to the liquid areas. A nucleus sufficient for the purpose might be provided by an area of pro-eutectoid cementite which had not become diffused during the

Jan 12, 1913

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By G. Thodos, R. J. Smialek

A method has been developed that permits the correlations of Mehra and Thodos8 and Dastur and thodos2 for binary systems to be used for the prediction of the vapor-liquid equilibrium constants of the light and heavy constituents, Kland Kh, of a ternary hydrocarbon mixture. Furthermore, the unique relationship observed in this study, i.e., a plot of log Ke/Ki vs log Kp/K h is linear and passes through the origin, permits the calculation of the K-value for the intermediate component. This approach has been used to establish K-values for the constituents of the three ternary hydrocarbon systems used to develop this method and has also been applied to two additional ternary hydrocarbon systems to yield an average deviation of 7.7 per cent resulting from a total of 294 points for the five ternary systems considered. INTRODUCTION The rigorous calculation of vapor-liquid equilibrium constants for systems containing two or more components is a difficult problem and becomes extremely complex at elevated pressures and for conditions approaching the critical point. Although thermodynamic relationships can be developed to account for the vapor-liquid equilibrium behavior of simple systems, their use is limited because the necessary PVT data for these systems are not generally available. To establish a method for calculating K constants directly, without any recourse to the PVT behavior of a system, Mehra and Thodos8 applied the principle of corresponding states to the vapor-liquid equilibrium constants of binary hydrocarbon systems. They developed a series of charts which made possible the prediction of K-values for all binary hydrocarbon systems not containing methane. This work has been extended by Dastur and Thodos2 to include binary hydrocarbon systems containing methane. The charts developed in these two studies cover the high-pressure region and are applicable to conditions in the vicinity of the critical point. The ability of this approach to predict vapor-liquid equilibrium constants of binary hydrocarbon systems suggests that this method may be extended to the prediction of the K-values of the components of ternary hydrocarbon systems. In this investigation, the charts developed for both the methane and non - methane binary systems,2,8 together with mixture rules developed in this study, have been used to predict the K-values of the light and heavy components of a ternary hydrocarbon system. These calculated values are then used to establish the K-value of the intermediate component through the use of a novel relationship developed in the present study. DEVELOPMENT OF METHOD FOR PREDICTING K-VALUES OF TERNARY SYSTEMS The application of the corresponding state charts developed for binary hydrocarbon systems is restricted to those systems containing two components. The extension of these correlations to three-component systems requires that the ternary system be reduced to an equivalent binary, which can be treated in a manner consistent with the corresponding state development. To establish such an approach, the vapor-liquid equilibrium constant of the light component K is first calculated by assuming that the ternary mixture consists of the light component and a pseudo-heavy component of the intermediate and heavy constituents of the original ternary. To establish the vapor-liquid equilibrium constant of the heavy component Kh, the light and intermediate constituents of the ternary are combined to form a pseudo-light component of another equivalent binary system. The calculated values Kl and Kb are then utilized to calculate the vapor-liquid equilibrium constant of the intermediate component EQUILIBRIUM CONSTANT FOR LIGHT COMPONENT K To calculate the K value of the light (most

Jan 1, 1965

By Douglas Baker

Zinc concentrates assaying approximately 54% zinc and 30% sulfur are roasted in a suspension type roaster to yield a zinc oxide calcine assaying about 65% zinc and 0.40% sulfur. This calcine is the feed material to the sulfuric acid leaching section of an Electrolytic Zinc Plant. The SO2 gases resulting from the elimination of sulfur from the concentrates are passed through a waste heat boiler for the generation of high pressure steam, cleaned by a baghouse, and delivered to the humidifying tower of a sulfuric acid plant system. The gases are then treated in a mist precipitator for final fume removal and then converted to sulfur trioxide in a three pass contact system using vanadium pentoxide catalyst for the manufacture of sulfuric acid. Waste heat steam is used to power the steam turbine which drives the acid plant blower.

Jan 1, 1970

By B. G. Ricketts, A. Kelly, P. A. Beck

The isothermal kinetics (at 200" to 400°C) of subgrain growth and of softening were studied in a 99.997 pct pure Al crystal rolled to 80 pct RA, under conditions where recrystallization did not take place. It was found that the kinetics of subgrain growth and of softening were similar, and that the correlation between subgrain growth and softening was in first approximation independent of the annealing temperature. It has been shown by Heidenreich' by means of electron transmission microscopy and by Hirsch and Kellar2 by means of an X-ray microbeam technique that the crystals of heavily cold-worked polycrystalline aluminum consist of subgrains of approximately 2µ diam, which are slightly disoriented with respect to each other. This substructure is found on cold working at room temperature, without annealing. A preliminary study has been previously published3 of the softening upon annealing at 350°C of a heavily cold-rolled aluminum single crystal. Softening and X-ray line sharpening for such a rolled aluminum crystal were later studied in more detail as a function of annealing time and temperature.4 Perryman5, 6 has studied the recovery of polycrystalline aluminum after cold rolling. By means of phase contrast microscopy he found that the subgrain size increases with the annealing temperature but does not alter very much with annealing time at a given temperature. In the present work further study was made of softening as a function of annealing time and temperature and subgrain sizes were determined by two different techniques in an attempt to find any correlation that may exist between softening and subgrain growth. Subgrain size measurements were made both by the X-ray microbeam technique and by transmission electron microscopy. EXPERIMENTAL PROCEDURE For the X-ray studies specimens were cut from

Jan 1, 1960

By Charles Mabery

So FAR as the elementary composition of petroleum is -known, it may be briefly stated. Petroleum consists principally of a few series of hydrocarbons, with admixtures of sulfur, nitrogen, and oxygen derivatives in comparatively minute proportions, which may be regarded as impurities to be removed in the preparation Of commercial products. But as each series is represented by many homologs, in the aggregate, crude petroleum is an extremely complex mixture of hydrocarbons and their derivatives. In part, these hydrocarbons individually conform in structure to the system of synthetic hydrocarbons whose structure is well defined and -represented by the typical series CnH2n+2, CnH2n, the series CnH2n-2, CnH2n-4, the members of which have not been sufficiently studied to establish their structure, and the series CnH2n-6 composed of the aromatic group, benzene and its homologs. Hydrocarbons of greater density contained in the portions of petroleum that cannot be distilled without decomposition doubtless have less hydrogen than is represented by these formulas. Since to every hydrocarbon there is a definite temperature, even in vacuum, at which its constituent carbon and hydrogen atoms fall apart, and since for the heavier bodies this temperature is not much above 360° C. in vacuum, it is evident that some other method than distillation must be devised for their separation if anything further is to be learned concerning their individual constitution. CLASSIFICATION OF PETROLEUMS There is such a wide variation in the composition of petroleum from different fields, it would seem possible to make a classification on this basis were it not that no single variety is entirely free from hydrocarbons contained in others. Such a classification has been suggested of the exceptionally pure Pennsylvania petroleum, the sulfur oil from Trenton

Jan 2, 1920

By J. Fred Johnson

MORE ORE is mined in the Bingham District than in any other mining district in Utah. In addition to the open-pit operations of the Utah Copper Co., there have been, many large underground mines. Until recent years the principal production was from the Jordan and Commercial limestones, but in the last eight years valuable ore deposits have been developed in the so-called alphabetical or "A," "B," "C," and "D" limestones, mainly by the U. S. Smelting, Refining & Mining Co. The value of these developments has led the company just mentioned to acquire large holdings in the district and within the last year to install at the Niagara shaft a hoist capable of going to a vertical depth of 4000 ft., or 1800 ft. deeper than the present lowest level. Ore from Bingham has been the chief factor in enabling the

Jan 1, 1934

By George W. Healy, Ko Yamaguchi

In typical calorimetry the energy given off by a material under study is transferred to a water bath, whose temperature is sensed by a thermometer; for correct measurement the water bath must attain a uniform temperature to which the thermometer must respond. This introduces two sources of error, non-uniformity of the heat sink and a time lag until its temperature is registered. These errors may become important where a rapid process such as solidification of metals and alloys is being studied by means of Oelsen'sl quantitative thermal analysis. To overcome this difficulty, a calorimeter sink was conceived in which the water bath is replaced by a copper coil, which serves simultaneously as heat

Jan 1, 1967

By R. L. Boyer, F. Morgan, M. Muskat

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947

By M. Muskat, R. L. Boyer, F. Morgan

In the last several years a type of application of the fundamental permeability-saturation relationships has been developed which offers great promise in the interpretation of general reservoir performance.l-' In these developments no attempt is made to solve the detailed flow dynamics in actual oil and gas-producing systems. That problem still remains unsolved. But the permeability-saturation phenomena are incorporated in the analysis of oil-producing reservoirs in a manner such as to reflect the true role they play in controlling the gross reservoir behavior. In particular, they are introduced in such a manner as to determine the gas-oil ratio of the production at any stage of depletion, and, when combined explicitly with the so-called material-balance principles in differential form, one can obtain a differential equation describing completely the average pressure and gas-oil-ratio history of oil-producing reservoirs. While thus far they have been applied directly only to gas-drive reservoirs, they are susceptible of extension to partial water-drive systems, and qualitatively the same principles are of value in the study Of complete water-drive reservoirs. Moreover, in addition to giving a means for computing the variation of the reservoir pressure and gas-oil ratios vs. the cumulative production, they automatically lead to predictions of the gross ultimate recovery under natural depletion—and when properly extended they provide means for predicting the ultimate recovery under gas or water injection. The data required for such applications are the initial fluid distribution in the producing section, the pressure-volume-temperature data on the gas and liquid phases, and the permeability-saturation relationship for the oil-satuiated zone. The former can be obtained with reasonable accuracy by methods that are well established and available throughout the industry. The permeability-saturation data, however, involve techniques that are not at all standardized. In fact, only

Jan 1, 1947